Search Documents

By L. McFarlane, D. Rollwagen

"Madawaska Mines produces a uranium precipitate (83-85% u3o8) using a magnesium oxide slurry to precipitate the uranium from solution. The solution, at approximately 9""0 g/l u3o8 is neutralized to a pH of 7.0. At the Eldorado Nuclear Refinery in Port Hope, the precipitate is not acceptable as a single feed to the refinery process. It was discovered that a 2% silica impurity caused emulsion problems in the solvent extraction column.After extensive studies of possible solutions, such as two-stage precipitation and solvent extraction, an acceptable solution was found. The selective precipitation of uranium at a pH of 3.5-4.0 using Hydrogen Peroxide produces an almost silica free product of higher purity (90-93% u3o8) to that of straight magnesium oxide precipitation. Introduction Madawaska Mines Limited is located four miles southwest of Bancroft, Ontario. The annual production of u3o8 is approximately 610,000 pounds. To produce the final product or yellowcake, nine separate steps are required. These are (1) grinding, (2) dewatering, (3) leaching, (4) acid filtration, (5) clarification, (6) ion exchange, (7) precipitation, (8) washing, and (9) drying and packaging. To illustrate these steps, a complete flowsheet of the mill is displayed on page three.The yellowcake is sent to Eldorado Nuclear Limited in Port Hope, Ontario for further concentrating and refining. As part of their routine specification check, a test called the amenability test is performed. This test indicates how a particular dissolved yellowcake product reacts to solvent extraction. The Madawaska yellowcake did not pass the test."

Jan 1, 1982

By A. Griffiths, G. Vickell

"INTRODUCTIONA successful cyanide destruction process has to ensure environmental compliance at reasonable cost. That this is possible with hydrogen peroxide is shown by the fact that over twenty gold mines either already use H2O2 or intend to start using it within the next few months. About half of these mines are in Canada.This growth is remarkable, considering that the first treatment plant to use H2O2 for detoxifying cyanide was commissioned less than five years ago at Ok Tedi, in Papua New Guinea.Hydrogen peroxide is being applied to a wide range of situations, including:Treatment of CIP pulps; examples: Ok Tedi, PNG; Hope Brook, Nfld.Treatment of barren bleeds and filtrates; examples: Nickel Plate, B.C.; Puffy Lake, Man.Treatment of tailings pond discharge; examples: Detour Lake, Ont., Page Williams, Ont.Treatment of excess heap leach solution; examples: Hope Brook, Nfld; Gordex, NS.Treatment of barren heaps after heap leaching; examples: Alhambra, NV; Wharf Resources, S.D.Treatment of pond reclaim water to prevent either ""preg-robbing"" or depression of gold-bearing pyrite in a flotation step; example: Getchell, NV.Treatment of backfill to prevent possible groundwater contamination; example Hope Brook, Nfld.Treatment of tailings ponds to prevent bird kills; example: Paradise Peak, NV.""Emergency"" units to deal with unusual events such as freak storms or dam failures."

Jan 1, 1989

By G. A. Gross

Nearly 90 per cent of the iron ore produced in Canada is derived from iron-formation or bedded iron deposits. About 70 per cent of this consists of concentrates obtained fom iron-formation; another 20 per cent was formed by natural enrichment processes. Four principal varieties of iron-formation are recognized -the Algoma, Superior, Clinton and Minette types. Differences in their geology, mineralogy, chemical composition and environment of deposition are of special significance in their evaluation as ore.

Feb 1, 1966

By Jean-Luc Beaudoin

"In addition to the actual energy consumed, billing is dependent on the peak load and the power factor. The lower the power factor goes, the higher will be the penalty the consumer pays. The principles of a power factor regulator, the two ways of improving the power factor and methods for calculating the capacitor values required will be described.The rate structure of the utility company is founded on three cornerstones: the energy consumed during a given period of time and two penalties imposed when the power factor is low or the power demand is high. Even though the normal consumption of a customer might be 10 kW, with a peak demand of 20 kW only once a month, the wiring and associated equipment at the input to the customer's plant will have to accommodate this peak demand. The power company has no means of forecasting these demands and cannot therefore provide the additional equipment necessary. So it exacts a penalty, and the customer must take all possible steps to avoid these peak power demands. This can be accomplished by using an automatic peak load regulator which will selectively disconnect the loads which are not essential in the operation of a plant .The principles of such a controller will be described.Principles of power factor regulatorsThe operating principles of a power factor regulator will now be described. It might be asked why the power factor of an electrical installation in a mine, or a factory, should be corrected at all, but there is a simple answer. In addition to the actual energy consumed, the billing is dependent on the peak load and the power factor. The lower the power factor goes, the higher will be the penalty the consumer pays."

Jan 1, 1982

By Tim Robinson, Michael S. Moats, William G. Davenport, Andreas Filzwieser, Andreas Siegmund, Shijie Wang

This survey continues the long tradition of providing a snapshot of operating data from industrial electrorefineries. It is a supplement to previous surveys that were performed in 1987, 1991, 1995, 1999, 2001, 2003, 2007, 2010, 2013 and 2016. Analyses of current data and historical trends are presented. Examples of innovations to reduce costs, improve productivity, and improve quality are provided. In general, refineries continue to increase productivity while treating anodes with more impurities. INTRODUCTION This manuscript analyzes global survey data provided by operating copper electrorefineries. This paper continues a series of surveys of copper refining tankhouses that started in 1987 (Schloen, 1987, 1991; Schloen & Davemport, 1995; Davenport et al., 1999; Robinson et al., 2003; Moats et al., 2007, 2013, 2016). In this installment, data collected from 2015 and 2018 will be presented and analyzed. The 2015 survey data were presented at Copper 2016 in Kobe, Japan. This survey will continue the analysis of previous data to illustrate long term trends in copper electrorefining, which were originally presented at the Davenport Symposium in October, 2014 (Moats, Robinson, & Wang, 2014). Refineries who supplied surveys are listed in Table 1. Cathode production data from 2015 and 2017/18 (from surveys presented in 2016 and 2019) are provided to indicate which plants provided surveys and when. This manuscript presents operating data for ~6.5 million tonnes of copper production, which represents 30–35% of the world’s copper electrorefining production. The detailed survey results are available upon request from the corresponding author.

Jan 1, 2019

By Z. Z. Öztürk, N. Sarica, A. H. Üçisik, C. Bindal

"Titanium oxide films were fabricated on commercially pure titanium surfaces via anodization procedure. Anodization parameters, anodization time and voltage were altered, whereas temperature and chemical composition of anodization bath were kept constant. The main idea in this study is to obtain rough titanium-oxide surfaces. The type and feature of titanium oxide formed were observed via SEM and EDX analyses. What was revealed from SEM and EDX analyses were combined with Ti-O phase diagram in order to make judgment on the type of phases obtained, e.g. solid solution and/or compounds. Studies on the different regions of each sample showed that surfaces consist of different titanium oxide compounds with various O/Ti ratios in nano level and solid solutions varying in terms of chemistry on the same sample. Thus together rough surfaces and inhomogeneous distribution of "titanium oxides" were obtained. It was also found that when anodization time and voltage were increased, more granular surface with higher O/Ti atomic ratio was obtained."

Jan 1, 2015

By Lyall J. Lichty

THE property of New Calumet Mines, Limited, is on Calumet island, in the Ottawa river, about sixty-six miles northwest of Ottawa. Lead and zinc orebodies were discovered here in 1893. A gravity concentration plant was built in 1912 but was not a success metallurgically, and the plant was later destroyed by fire. A programme of diamond drilling on the property, started in 1937 and continuing to 1942, indicated ore reserves amounting to 1,300,000 tons averaging 2.75 per cent lead, 8.82 per cent zinc, and 0.041 oz. gold and 6.24 oz. silver per ton( l ). These orebodies have been developed underground by cross-cutting and drifting from a three-compartment vertical shaft, sunk to a depth of 745 feet. 'The ore is a contact metamorphic deposit occurring in rocks of the Grenville series, on or near the contact between biotite gneiss and an overlying calcareous amphibolite(2,3). It consists chiefly of iron-bearing sphalerite, galena, pyrrhotite, pyrite, and minor amounts of chalcopyriteand argentite. The gangue minerals closely associated with the ore are calcite, quartz, and various lime-silicate minerals.

Jan 1, 1945

By J. Lebl, S. Bharti, D. J. Cornett

"This paper presents the design and application of blasthole mining to an area at Strathcona Mine previously employing post pillar cut-and-fill. Extensive mining in the area had led to gradually deteriorating ground conditions and post pillar stoping was no longer considered acceptable. Alternative methods had to be investigated.Conventional methods for mining in poor ground were rejected because of the high cost. Blasthole mining was selected because iI offered good productivity and safety with acceptable costs. The design of this approach involved field investigations and the use of numerical modelling to simulate the different blasthole options and their impact on ground stability. The blasthole design incorporated reinforcement with cablebolts, use of a radio-controlled remote LHD unit, large-diameter holes, blast design and wall control. Potentially unstable areas were outlined during mining with ground monitoring instruments and the results used to modify mining plans during the production phase.IntroductionIn underground metal mines there is a need to improve safety and productivity and lower mining costs in order to maintain reasonable rates of return on investment. This requires the application of good engineering design to both mine planning and ground control in order to optimize production and costs and to forecast potential problems during mining. The task becomes more important when extensive mining leads to gradually deteriorating ground conditions, making existing mining methods and techniques no longer acceptable from a safety point of view. Alternative mining methods must, however, be sufficiently productive to ensure profitability. This paper presents an example of the engineering design and operating approach used by Falconbridge in dealing with such a situation at Strathcona Mine."

Jan 1, 1983

By O. Guyot, A. Broussaud, M. Revalor, G. Legrand, D. Kok, E. Roux

"The paper describes the advanced grinding control system implemented at Newmont Ahafo gold mine, Ghana in 2009 and 2010. It shows how the different components of the Advanced Process Control (APC) system cooperate for increasing plant performance.The SABC circuit processes hard rock from different pits mixed with a variable proportion of oxides. The control strategy is designed to address specific disturbances, including start/stops of pebble crushers, unavailability of oxides, changes in rock size distribution resulting from segregation in the stockpile, and changes in ore type and hardness.The system consists of an expert system per se with extensive use of fuzzy logic, supplemented by an online dynamic model of the process used as a soft sensor, a VisioRock™ rock size measurement system over SAG mill feed before addition of recycled pebbles, and an AudioMill™ system to analyze the SAG mill sound and detect impacts on liners. All these components are embedded in the same OCS© software platform, which, among other benefits, makes it easy to support the entire system remotely. The paper details the physical constraints and the variables that are manipulated. It describes the control strategy and the contribution of each component of the system. It also describes the project implementation and the performance of the system. In addition to a strong involvement and support of management, the very good acceptance of the operators has been facilitated by the remote access system that made it possible to immediately modify the system each time it was needed during the baby sitting phase.The system made it possible to increase gold production significantly through increases in tonnage and recovery thanks to a better control of the grind size through a stabilization of the secondary ball milling circuit and an improvement of the operating conditions of the classifying cyclones."

Jan 1, 2012

By J. Keith Haddock

"Introduction The Boundary Dam Mine is located 5 km south of the City of Estevan, Saskatchewan and is operated by Manitoba and Saskatchewan Coal Company Ltd., one of the Luscar companies. The entire production of 1.7 million tonnes per year is delivered to the Boundary Dam Generating Station of Saskatchewan Power Corporation. Geology There are basically two seams mined on the property, the main Estevan seam ranging in thickness from 3.0 m to 4.5 m with partings and the upper Roche Percee seam (roughly 15 m to 23 m above the Estevan) which ranges from 0.6 m to 2.0 m in thickness. Most of the reserves are concentrated in the Estevan seam, the Roche Percee only being mined whenever its thickness makes it economic to recover. The coal measures belong to the Ravenscrag Formation of Tertiary (Paleocene) Age. This formation is widespread in North Dakota and Montana and contains the lignite fields of North Dakota and subbituminous coals of Montana. The formation is gently tilted to the southeast at Boundary (0.5 degrees) and consists of weak sandstones, siltstones and silty mudstones. Reserves and Coal Quality The present minesite encompasses a coal reserve of approximately 50 million tonnes calculated to a maximum stripping depth of 37 metres or 20:1 mining ratio. The reserves form only a part of the total reserves in the Estevan area which are owned by the Saskatchewan Power Corporation. The coal being mined is classed as Lignite ""A"" and has the following specifications:"

Jan 1, 1985

By G. W. Clark

"The mining of the ore bodies at Rabbit Lake has in the past been by the open pit method. This method is presently being used to develop the B-zone and will continue into the future with the development of two smaller ore bodies, the A-zone and D-zone. The Eagle Point orebody will be developed by an underground method which will provide production and employment into the next century.The ore bodies at B-zone, A-zone and D-zone are unique in that they are located under Wollaston Lake. To permit mining by the open pit method a steel-celled dyke has been constructed around the north end of the B-zone. This same dyking method will be used for the A -zone and D-zone. INTRODUCTIONMine development at Rabbit Lake commenced in 1970when a detailed engineering feasibility study established the viability of the Rabbit Lake deposit. In 1972 construction of the mill and camp site began. Construction materials were seasonally hauled to the site over a winter road until November 1973when the government of Saskatchewan completed an all-weather road to within six miles of the operation.In October 1974, stripping of the Rabbit Lake open pit began with the removal of overburden and lake bottom sediments from the previously drained Rabbit Lake. The first ore was processed by the mill in June 1975and by October the mill was producing three million pounds per year. The design capacity of five million pounds annually was first achieved in 1977 and maintained until 1981, when lower ore grades resulted in lower production rates .It was clear when mining at Rabbit Lake began that, without additional reserves, the Rabbit Lake operation had a life of less than 10 years. Exploration, therefore, continued in the immediate area in an attempt to discover additional uranium mineralization."

Jan 1, 1989

By W. P. Corking

"The purpose of this paper is to describe the relationship of the goldbearing ore to structure at the Pickle Crow mfoe. Information beyond this scope may be found in the reports and papers of Hurst( l), Bothwell(2), Thomson(3) , and Monette( 4).The property lies on Crow river, in Patricia district, 80 miles northeast of Allanwater, and about 125 miles northeast of Sioux Lookout on the Canadian National railway. From April of 1935, when the mill began operation, to the end of 1944, a total of 564,890 oz. gold and 49,275 oz. silver were recovered from 958,416 tons of ore.Mining on the property is at present carried on in two separate orebodies, the Howell and the No. 2 vein. Stoping has been carried on from every level on the Howell vein to a depth ot 2,450 feet below the surface and from several levels on the No. 2 vein through a mile long cross-cut on the 750-foot level to the Howell vein workings. A steadily increasing volume of ore is being obtained from the No. 2 vein.Each of the two orebodies consists of vein quartz with small amounts of other gangue minerals either in a single vein or a stockwork of veins. Both lie within sheared walls and carry gold in the free state. Fig. 1 shows the position of the veins with respect to the surrounding rocks. It will be noted that the delineation of the beds of iron formation shows that the lava flows and minor, interbedded sediments that make up most of the country rocks are areally folded and contorted.STRUCTURENearly all gold found to date in sufficient quantity and concentration to make ore in the Pickle Crow area is confined to these major quartz veins . Both strike a little north of east and dip north, and in both cases the attitude of the enclosing rocks is somewhat more north of east in strike and more steeply north in dip than that of the veins. As a result of this disposition both veins migrate across their enclosing rocks at a moderate angle in both dip and strike. (In this connection it should be noted that No. 2 vein dips at a considerably flatter angle than its host rock, but has a very pronounced rake to the northeast, effecting the same result as in the Howell vein.)"

Jan 1, 1954

"The North Star and Don Jon copper deposits lie beneath the waters of Thompson Lake, which is 12 miles east of Flin Flon, Manitoba. The deposits were discovered during the years 1949 and 1951 by diamond drilling done in the vicinity of pyritic showings on the shores of two small islands in the lake. The Don Jon ore body lies 1, 700 feet southeast of the North Star orebody and is connected with the North Star mine workings by a crosscut on the 600-foot level (Figure 1 ).Production began on January 1, 1955, at a combined rate of 200 tons per day. The ore is trucked, on 24 miles of highway, to the Hudson Bay Mining and Smelting Co., Limited mill at Flin Flon.Regional GeologyRocks in the Thompson Lake area are Precambrian volcanics, ranging in composition from andesite to rhyolite, with related tuffs and breccia. These rocks have a general north-south trend and are steeply dipping. The area is part of the Lac Aimee fault block, which probably is the southward extension of a south-plunging syncline now thrust some miles to the north. This regional deformation has produced many subsidiary zones of intense shearing and crumpling. It is in two of these zones of shearing and drag-folding that the orebodies occur. The only recognizable intrusive is a narrow diorite sill which trends northeasterly near the west shore of Thompson Lake.The North Star MineA pyritic showing, carrying some chalcopyrite, was discovered around the year 1930 on the west side of a small island near the west shore of Thompson Lake. This ground was included in a group of claims acquired by the Hudson Bay Exploration and Development Co., Limited in 1947.In the years 1949 to 1951, a diamond drilling program outlined a copper sulphide orebody. This ore zone comes to surface beneath the lake, about 300 feet north of the pyritic showing on the island."

Jan 1, 1949

By Gordon L. Kidd

The object of this paper is to show the relations of the East Coulee coal area to the near-by Willow Creek, Wayne, Rosedale, and Drumheller areas, all being parts of the Drumheller field. The word ?area? is here used in a more local sense than that employed by Dr. J. A. Allan, whose. 'area' is rather comparable with the 'mining division' in British Columbia. I have drawn freely from the published information, particularly from Dr. Allan's report on the "Geology of Drumheller Coat Field, Alberta", and from Dr. E. Stansfield's paper on " A Chemical Survey of Alberta Coals", to whom thanks are due. The Drumheller field is served by branch lines of the two principal Canadian railways. The C.N.R. traverses the district by its Goose Lake line from Calgary to Saskatoon; and the C.P.R. by a line from Calgary to Acme and then southeasterly to Drumheller, where it effects a junction with the C.N.R., over which the C.P.R. has running rights as far as Rosedale. From Rosedale, a joint line built during the summer of 1928 extends about forty miles down the Red Deer river to the mouth of Bull Pond creek. From that point the C.P .R. turns more southerly to connect with the Bassano-Empress line. The C.N.R., it is expected, will eventually proceed eastward to connect with a transcontinental line. The joint line from Rosedale down the Red Deer river opened up the Willow Creek and East Coulee areas.

Jan 1, 1929

By G. Bimpilas, G. N. Anastassakis

"Today, one of the most intense problems in mineral processing systems is referred to the treatment of fine (–100 µm), and even smaller size, particles. Fine mineral particles possess specific properties (small mass, high specific surface area, and high surface energy per unit area) that render their separation inefficient with conventional methods (physical, physicochemical) and equipment. As a result, it is not feasible to obtain a concentrate both of high grade and recovery in mineral value and a considerable amount of mineral fine particles is lost to the tailings. As evidence, we could cite numerous examples from industrial practice with considerable loss of mineral values to the tailings because of the fine particles size, e.g. phosphate, tungsten, tin, etc.The objective of the current paper is to investigate the possibility to separate magnetic gangue minerals and rocks (serpentine, ilmenite, and olivine) from magnesite by co-agglomerating all the gangue components and subsequent magnetic separation of the agglomerates.To meet the target, hydrophobic agglomeration tests were initially carried out on single minerals to define the favorable conditions for selective hydrophobic co-agglomeration of the gangue minerals. In this respect, the effect of the following factors was examined: pH, collector dose, conditioning time, and settling time of the agglomerates. Among the combinations examined, the most favorable proved that with amine in the basic pH region. The use of non-polar oil proved beneficial. The preliminary results were confirmed by tests on mineral mixtures. The application of magnetic separation resulted in the removal of gangue minerals and the recovery of magnesite concentrates of commercial grade (magnesite content 95% approximately) and high yield.The current paper contributes to the development of mineral processing, since it successfully copes with a very important problem of mineral processing, such as the efficient separation of fine particles."

Jan 1, 2016

By D. Mraz

"Under high pressure in a deep potash mine, the salt rock behaves in accordance with the concept of a generalized, perfectly plastic substance. The paper presents the evidence of this behaviour and engineering concepts f or room-and-pillar design. IntroductionThe mining and refining facilities at International Minerals &. Chemical Corporation (Canada) Limited are located near Esterhaz y at the southeastern edge of the Saskatchewan evaporites. Ore extraction began in 1962 and at the present time the annual mining capacity is in excess of eleven million tons of potash ore.A generalized geological section is shown in Figure I. The mining horizon is overlay in by 100 feet of rock salt followed by a thin bed of competent dry shale. The strata in the next 1,500 feet are generally competent and locally water bearing. The Blairmore formation contains strata of water-bearing unconsolidated sand. Below the mining horizon, rock salt is interbedded with anhydrite bands.The 8-foot mining bed is distinguished mainly by grade and clay content, as there is no definite bed boundary. The chief mineral s are halite, sylvite and, in some cases, carnallite, with up to 2 per cent disseminated clay. The ore is coarse grained, with crystals averaging one-half to three-quarters inch across.The major mining problem is related to the fact that the Dawson Bay formation, overlying the evaporites, contains areas and channels that are highly porous and permeable and are filled with unsaturated brine under high pressure. Consequently, all mining areas, with no exception, must be so designed that the overburden salt stratum remain s competently supported for the duration of the mine .This paper outlines a successful engineering method of determining the stability of the pillar s and designing a stable room -and-pillar mining system."

Jan 1, 1980

By DAVID C. MILLER

Barite deposits occur worldwide and in a variety of geological environments. In recent years, several deposits of barite and barite-lead-zinc have been discovered in northern British Columbia, Yukon Territory and Alaska. Most are associated with Devonian-Mississippian age sediments, and many are syngenetic, bedded-type deposits. The Mel is a barite-lead-zinc deposit; it lies within Lower Cambrian strata and appears to be of epigenetic replacement origin. Figure I is an aerial view of the property from the south. Observations herein described are based largely upon field work, megascopic studies and two recent B.A.Sc. theses (Biasucci 1979, Rennie 1979).

Jan 1, 1984

By S. K. Paul

"This paper briefly describes the underground crushing and conveying system at Sherritt Gordon Mines' Ruttan Mine. A series of three steel-cord belted conveyors, with a total length of 2J55 metres and a total vertical lift of 407 metres, convey the muck from the underground crushing station to the mill at the surface. The maximum size of the crushed rock is 6 in. All the conveyors are provided with numerous safety and fire suppression devices. IntroductionThe Ruttan Mine of Sherritt Gordon Mines Limited is located 20 km east of the town of Leaf Rapids, 760 km north of Winnipeg. The orebody is multilensed, with lens width varying from 6 to 45 m. Ore production started in 1973 with the opening of a 10,000-tpd open-pit mine. Initial development of the underground mine was started in 1972 with the driving of parallel conveyor and access declines at minus-2507o gradient to the I 220-m level, and then the access ramp was further extended to the 1160-m level. Exploration drifting was done on the 1280-m and 1160-m levels from the access ramp. The final development plan for the underground project was approved in January 1977, and full-scale development and constructionwere resumed.At present, Ruttan Mine is in a period of transition from open-pit to underground mining. Ore production is now coming from both operations. By mid-1980, open-pit production will cease and all production will come from the undergroundmine.The underground mining method at the Ruttan Mine is sublevel open stoping with delayed backfilling. The orebody is divided along strike into a series of 27-m-long stopes and 15-m pillars, both 60 m high."

Jan 1, 1980

By Michel Noël

This paper presents a partial compilation of adopted measures of waste rock dump closures at mine sites located in Canada and Alaska, where the climate includes cold winters. The paper also presents the selection process that was followed for some of those mine sites. Mining operations usually generate waste rock that can sometimes result in very large quantities. Additionally, the nature of the ore body and the host rock will often introduce environmental impacts. These impacts need to be managed not only during the operations but also in the long term. Mine closure plans consequently have to address the long term issues that sometimes require perpetual treatment. Closure planning often involves the evaluation of risks associated with environmental and financial liabilities. It needs to consider the science, some common definition of objectives, and there will be a need to manage resources and schedules. Closure planning is essentially an exercise in constrained decision making. A performance and risk based ranking matrix is often developed during this selection process to identify the preferred option(s). The case studies presented in this paper provides a few examples. The level of knowledge on acid rock drainage from waste rock dumps has increased considerably over the past decades. It did not necessarily increase the level of complexity of the adopted closure methods, as the selected closure methods are often kept simple. A common approach consists of stabilising the slopes of the waste rock dumps material by resloping and then covering the waste rock with a growth media to support vegetation. Such covers prevent direct contact of animals with the waste rock material, minimise erosion and reduce infiltration to various degrees. The inclusion of water treatment is obviously dependent on the water quality being released.

Nov 1, 2008

By Chao Yang, Liguo Tian, Yan Yang

"The Jinfeng gold mine is one of the three gold mines that Eldorado Gold has in China and it is the second largest gold mine in China. The mine is located in a relatively remote and mountainous area in the southwestern Guizhou province. The orebody is similar to the Carlin type deposit in Nevada. The mill throughput was designed to treat 3,600 tones per day. The ore comes from open pit mining and underground mining, and is fed to one-stage jaw crushing. The crushed ore is stockpiled, reclaimed and then fed to the SABC grinding circuit. After classification with hydrocylones, the ore is floated, and the resultant concentrate is oxidized biologically in a process known as BIOX®. The oxidized concentrate is then washed in a CCD circuit and finally leached with cyanide in a CIL circuit for gold extraction. Jinfeng produces about 180,000 oz of gold per year.This paper introduces operations and modifications of SABC circuit over the past three years, and then describes some technical characteristic of the SAG mill and other circuits in the processing plant.Major modifications and improvements on the SABC circuit are described in the paper, including:1. Impacts of grinding ball and mill liner with respect to material selection, quality, hardness, manufacturing methods, and interactions between mill liner and grinding ball.2. Effect of milling operation parameters on milling efficiency.3. Impacts of SAG mill scats and modifications of grate size to improve mill throughput.4. Design and construction of a pebble crushing system, and recycle the crushed scats to the SAG mill to improve mill throughput.With the above-mentioned modifications, 20% increase over the design in mill throughput has been realized over the past three years, and operating cost has been significantly reduced. However, some issues still remain, and thus process modifications and technical innovations are still needed."

Jan 1, 2012