Search Documents

By Jianwen Yang, Yucai Zhou, Yanhong Dong, Daixiong Chen

"The study of combined depressants for flotation separation of lead from copper has been carried out to solve the copper-lead separation problem. Test results show that the depressant of CMC (Carboxyl Methyl Cellulose) or sodium sulfite plays an important role on the selective depression of galena flotation. When the two reagents above are combined, the selective depression effect on galena is further enhanced. When the mass ratio of CMC to sodium sulfite is 1:4, galena was best depressed, with the lowest lead content in the copper concentrateClosed-circuit tests indicate that under a certain pH value of the slurry, with the best ratio of CMC to sodium sulfite as depressants, the copper concentrate with the grade of 28.23% copper and 4.12% lead is obtained, and the copper recovery is 84.87%; the lead concentrate with 68.12% lead and 0.86% copper is obtained, and the lead recovery reaches to 92.20%. An efficient separation of copper and lead is achieved with the combined depressants. INTRODUCTIONComplex copper-lead-zinc sulfide ore is abundant in China. With the rapid increase of mineral consumption, it has become one of the important sources to produce copper-lead-zinc metals. However, it is difficult to achieve effective separation of copper and lead, due to the complicated ore properties, such as fine dissemination, low copper grade, complex symbiotic relationship and similar floatability of copper and lead.Poisonous reagents of bichromate and cyanide are often used as depressants for copper lead separation. They have good separation efficiency, but pose serious pollution issues. As the environmental protection is becoming more and more important, it is a trend to replace traditional toxic reagents with new nontoxic efficient chemicals. Organic depressant FCLS studied by Liu has strong selectivity against galena, and does not depress chalcopyrite. A new type of galena depressant of CLS-01 discovered by Jin-lin Yang shows good results in the separation a mixed copper and lead concentrate. In addition, dextrin, chitosan and some other natural organic compounds (Drzymala, 2003; Huang, 2012; Qin, 2013) have also been studied to separate copper and lead."

Jan 1, 2016

By Chaluvadi K. Sridhar, Prashanta K. Chatterjee

"IntroductionThe planning of an underground coal mine requires a complex blend of technical expertise, experience and subjective design criteria implemented by the mining engineer. Currently the procedure is largely manual and requires considerable resources to generate a single mine plan. Often three or four people are assigned to work in the development of a single draft layout. Evaluation of the layouts is also tedious as it requires many repetitive calculations. The evaluation of layouts developed manually generally attempts to derive a single economically feasible solution. Operational constraints in underground coal mining such as manpower, time, equipment, etc., do not allow the generations of more than one alternative layout. As a result, the first plan is generally the only one considered.Computer-aided mine planning can automate many of the manual procedures and calculations involved in mine planning thus allowing to evaluate man y layouts and mining strategies and to select the optimum plan with confidence. An optimized planning procedure will also provide the capability to evaluate mine performance continuously and critically, thereby helping to maximize return on investment. Although recent advances in computer graphics have provided the hardware necessary for developing and evaluating min e plans rapidly, software that will allow the mining engineer to make use of the new technology is slow in developing. The need for such software packages has been recognized and ackowledged.At several sessions in recent conferences on the applications of computers in the mining industry, the use and benefit s of computer-aided mine planning were discussed. However, there were few papers presented that referred to actual applications of interactive graphics to underground mine planning. The emphasis of this study is toward the development of a completely integrated computer-aided underground mine planning package that integrates geological modeling, engineering design and planning"

Jan 1, 1986

THIS article describes the origin and details of a hydraulically operated switch to control the operation of an automatic underground pumping system. This system was installed in December, 1939, on the 2,350-foot level at No. 5 shaft of the Buffalo Ankerite mine. The pumping unit consists of an 8-stage centrifugal pump direct-connected to a 150 h .p., 2,200 volt motor. Pumping capacity is 200 gallons per minute under a 1,315-foot head and with a flooded suction. The control consists of a 200 amp., 2,200 volt oil-immersed starter with thermal overload protection, thermal protection on the pump, and a flow switch that is bypassed for 30 seconds after the pump starts. The 30-second time lag is operated by a relay mounted on the panel. There is a swing check valve in the discharge line of the pump which originally operated the flow switch by means of a connected outside lever which closed the switch as the check valve opened.

Jan 1, 1945

By J. C. Ingles

"A survey of possible methods for controlling cyanide concentration indicated that the simplest method would involve the use of a potentiometric technique. Such a method was suggested by a paper from the laboratory of Mines Safety Appliances, which described a method for determining hydrogen cyanide in air. In this application, the cyanide was absorbed in caustic and a silver electrode immersed in the caustic solution provided a measure of the cyanide concentration. However, our attempts to use the silver electrode in this simple manner to measure the cyanide concentration of solutions were not very successful. A study of the mechanism by which a silver electrode responds to cyanide concentration made it evident why this simple procedure is not satisfactory.Basically, the silver electrode provides an indication of the free silver ion concentration of a solution, and generally speaking, ignores the other ions' present. It can be used to measure an anion if this anion complexes silver. This technique has been used in complexing studies to determine the activities of such anions as acetate, citrate, oxalate and chloride. To do this, the electrode has to be placed in a solution which initially contains a known concentration of free silver ions. Addition of the complexing anion causes a drop in the free silver ion concentration and hence a change in the potential of the silver electrode. The change in potential can be expressed in terms of the concentration of the complexing anion, and used to indicate its concentration in the solution being analysed. The determination of chloride-ion by a silver-silver chloride electrode is an example of an application of this technique. The solubility of the silver chloride with which the electrode is coated provides the initial free silver-ion concentration. Depression of this free silver-ion concentration by the presence of the excess chloride ion of the sample solution results in a change in the potential of the electrode which is proportional to the chloride-ion concentration."

Jan 1, 1965

By Janne Karonen, Stephen Hughes, Mikael Jåfs, Jan Stål, Hannu Johto

End-of-life electrical and electronic scrap material attracts attention as a good opportunity for new value creation through efficient metal and energy recovery of such materials. On the other hand, the treatment of such wastes becomes important to avoid problems for society and environment. Treatment of such secondary raw materials faces multiple challenges due to their increasing complexity and evolving nature. Processing of these complex scrap materials together with recovery of a wide range of valuable metals with a combination of pyrometallurgy and hydrometallurgy using Outotec technology is discussed in this paper. One key consideration is environmental performance which needs attention when processing such complex secondary E-waste materials. Outotec has successful experience with commercial projects in the countries at the forefront of environmental and operational standards. INTRODUCTION Increasing attention has been drawn to the responsible processing of end of life Waste Electrical and Electronic Equipment (WEEE) as part of metals recycling, especially copper. It has been estimated that the amount of WEEE globally in 2016 was around the level of 46 Mtpa (Balde et al., 2017), representing a major disposal challenge but at the same time huge opportunity for resource recovery. The potential for increasing the recovery is high, because the official recycling rate of WEEE is in 2016 only 20% (Balde et al., 2017) and at the same time the estimated increase of the WEEE amount is between 3 and 5% per annum in the EU (Eurostat, 2019).

Jan 1, 2019

By M. J. Bennett

"The Quemont mill is primarily a differential flotation plant in which copper, zinc ·and pyrite concentrates are recovered. Native gold and silver are associated in the form of very small particles with all the minerals contained in the ore: chalcopyrite, sphalerite, pyrite, pyrrhotite and even with the gangue rock.The proportion of the precious metals associated with chalcopyrite is such that the best recoveries we can obtain in our copper flotation concentrate are about 68 percent of the gold and 51 percent of the silver in the ore. In order to improve the total recoveries of precious metals it is necessary for us to float a pyrite concentrate and treat it by cyanidation for the extraction of whatever gold and silver we can obtain in this manner. In spite of the fact that we regrind this concentrate to 75 percent minus 325 mesh, it is difficult to extract much more than half of the gold and silver present in the pyrite concentrate by cyanidation, due to the extremely fine association of the precious metals with the pyrite.In 1963 we produced 86, 853 ounces of gold by flotation alone, and 14, 581 ounces by cyanidation. These amounts are equivalent to 67. 74 percent and 11. 37 percent respectively of the total gold in the mill heads. Comparable figures for silver are 325, 598 ounces by flotation and 99, 448 ounces by cyanidation; and 51.37 percent and 15.69 percent respectively.The total annual value of these metals (ie. $4, 000, 000) qualifies Quemont as a precious metal producer of some note. On the other hand, it is evident that by far the greater proportion of our gold and silver production is contained in copper flotation concentrates. When the income from our copper and zinc values is also considered, the much greater importance of flotation compared with cyanidation in our operation may be appreciated. This explains why most of our work on controls has been carried out in our flotation mill, rather than in our cyanide plant. Some of the controls installed there could, of course, be employed in either type of operation."

Jan 1, 1964

By D. Kershaw

"A world-scale surface mining operation is associated with the Syncrude Oils ands Plant. Each day over 300 000tonnes of oils and are mined and transported to the process plant to produce 129 000 barrels of synthetic crude oil.Examples of research and maintenance engineering programs which have resulted in substantial gains in dragline and bucket wheel conveyor system productivities are discussed. Two central themes within these programs, which go beyond the usual technical support associated with a large surface mining operation, are pursued:1. the approach taken to determine the causes of component failures and provide Syncrude performance specifications to allow manufacturing industry to respond with more appropriate products; and2. systems and equipment studies which have led to higher productivity in the major mining equipment and the development of an auxiliary feed system.IntroductionA world-scale open pit mining operation is associated with the Syncrude Oils ands Plant located near Fort McMurray in northern Alberta. Over 300 000 tonnes per day of oils and are mined and transported to the process plant. Fifty million barrel s of synthetic crude oil were produced in 1987, which represents 10010 of Canada's crude oil requirement.following tree clearing and surface drainage, overburden is removed by mobile equipment ahead of oils and mining. Draglines excavate the 40 m depth of feed grad e oils and which is windrowed on the dragline bench. Bucketwheels reclaim the oils and from the windrows for transport by conveyor systems to the extraction plant surge pile.The Syncrude mine is operated in four essentially equal quadrants, each serviced by a dragline and a bucketwheel conveyor system. The mining face in each quadrant is approximately 2 km long and reclaimed oils and is transported by 1830 mm shift able conveyors over distances up to 6 km. Individual conveyors vary in length up to 2500 m.The Syncrude plant started operating in late 1978, and Figure I shows the mine production history through to the end o f 1987. Annual production volumes have increased from 50 million tonnes of oils and in 1979 to 105 million tonnes in 1987.The period from 1982has seen a change in operating philosophy, away from striving for very high production rates, to operating at sustained targetted levels within the measured capacity of the equipment. Higher over-all production volumes have resulted from being able to operate for more hours at these rates. This same period has also seen much greater emphasis placed on routine inspection of the equipment and planned preventive maintenance to avoid problems which could otherwise impact on production."

Jan 1, 1990

By R. J. Mitchell

"The use of hydraulically delivered classified tailings sands to provide ground support in large mining operations is still widespread despite recent developments of alternate backfilling methods and materials. The major disadvantages of the use of hydraulic fill are the costs and risks associated with slurry delivery. The main risk is that of bulkhead failure resulting from sand liquefaction due to insufficient operational control or due to dynamic loading from earthquake or rockburst. That risk may be eliminated by the pouring of a stiff cemented sand plug in the base of each stope prior to continuous fill pouring in that stope. An additional advantage of cemented plugs is that massive bulkheads are not needed. Instead, a temporary (removable and reusable) bulkhead can be used for plug forming.Physical model studies of fill pressures on a temporary bulkhead were carried out in a 3 m radius centrifuge facility. Fill pouring in-flight was carried out in order to model prototype stress paths. The results indicate that the average bulkhead pressure is likely to be less than 10 kPa under normal operating conditions and less than 20 kPa under the poorest anticipated operating conditions which include smooth walls, high slimes content and high water-content slurries. A portable bulkhead consisting of a central core and a surrounding sealing bladder was modelled and found to be effective. The use of different sizes of cores allowed the stress distribution adjacent to these bulkheads to be evaluated."

Jan 1, 1992

By C. Feng, D. W. M. Arrigan

Arsenic is often associated with gold mining operations and poses a significant health and environmental hazard. While a number of technologies are available for removing arsenic, none of them is effective under all conditions. Although adsorption is a promising approach, most methods focus on the purification of water under neutral or acidic conditions and tend to be less effective in gold mining process waters, operating under alkaline conditions. In this study, the removal of As (III) and As (V) from both arsenic-only solutions and simulated process waters using composite magnetic nanoparticles was investigated. The nanoparticles consisted of magnetite (Fe3O4) or maghemite (?-Fe2O3) cores covered by various metal oxides with Langmuir adsorption capacities of As (III) and As (V) ranging from 31.4 to 79.1 mg/g and 10.2 to 25.5 mg/g, respectively, in arsenic-only solutions at pH 9. Their adsorption capacities were further recognised by the adsorption tests conducted in simulated process waters. The ability to remove As (III) is of particular importance as it is harder to remove it from alkaline solutions. The magnetic cores allow simple and efficient magnetic recovery of the As-loaded nanoparticles.

Jan 1, 2017

By Jiahao Xu, Namsoo P. Kim, Guikuan Yue

Iron (ferrous ions and ferric ions) plays an important role in the heap leaching of copper sulfide minerals and copper electrowinning. In our previous study, a novel oxidation-reduction potential (ORP) equation only based on the variables of temperature and nominal ferric/ferrous ratio was developed to predict the redox potential of the quaternary H2SO4-Fe2(SO4)3-FeSO4-H2O system, and its applicability was also extended to more complex acidic iron sulfate solutions, especially those generated during the acidic leaching and bioleaching of Printed Circuit Boards (PCBs) to recover copper. In this work, the broader range of applicability of this equation to other complicated acidic iron solutions containing copper ions has been extended and determined. Specifically, synthetic iron-containing solutions with copper ions according to the conditions of industrial electrolyte during copper electrowinning and heap leaching have been used to measure the ORP and test the developed equation. It seems that this equation can still be employed to predict the redox potential of the Fe3+/Fe2+ couple for the simulated solutions under conditions related to copper electrowinning and pregnant leaching solution generated during heap leaching over a wide range of solution concentration, nominal Fe3+/Fe2+ ratio and temperature. It has shown that the prediction and measurement of redox potential is highly useful to estimate and understand the iron chemistry of industrial leaching and electrowinning processes. INTRODUCTION It is well-known that iron (ferric or ferrous) ions are widely involved in the hydrometallurgical production of non-ferrous metals such as Cu, Au and Zn, mainly in the form of acidic iron sulfate solutions. As far as Cu is concerned, in a typical leaching-solvent extraction-electrowinning process, ferric ion plays a central role in the heap leaching process and is reduced to ferrous ions in the pregnant leaching solution. Ferric ion is the most important surrogate oxidant and the dissolved ferric/ferrous couple plays an important catalytic role in accelerating the leaching rate with oxygen as an oxidant (Peters et al., 1986; Schlesinger, King, Sole, & Davenport, 2011). In addition, during the traditional electro-winning process, oxygen is evolved at the anode, and copper is reduced at the cathode. A common idea is that iron in the electrolyte in copper electrowinning cell (with total iron of 1–4.4 g/L) plays an important role in reducing the current efficiency. According to the published results (Winand et al., 1975; Dew et al., 1985; Moats et al., 2009; Khouraibchia et al., 2010), thecurrent efficiency decreases linearly with increasing ferric ion concentration and the energy consumption increase was mainly caused by the decrease in current efficiency.

Jan 1, 2019

By Charles Goodeve

"BEFORE I begin, I should like to thank The Canadian Institute of Mining and Metallurgy for the honour they have bestowed in inviting me to give this address at the fourth annual C.I.M. Conference of Metallurgists banquet.Secondly, I should like' to convey the greetings of the Iron and Steel Institute of Great Britain in accordance with a request made by its Council at its last meeting. The I.S.I. hopes for the continued growth in strength of this annual Conference and in the collaboration between our respective societies.When I read the program of this Conference, it was brought home to me what a non-ferrons country Canada is. Also, I realized what enormous advances have been, and are being made, and what an ex-citing field non-ferrous metallurgy is for the scientist. This made me wonder, as I have done before, whether the future for steel was proof against these advances.At present, iron and steel stand astride the metallurgical world like a Colossus; I hope that the bronze industry will pardon my stealing their thunder and mixing my metaphors! Will this still be so in the future?The best way to answer this question is to take a look at the fundamentals to see why the iron atom dominates to such an extent that al! other metals are called ""non-ferrons."" Is its present position due to historical and therefore ephemeral reasons, or is there a fundamental difference between the atom of iron and those of other metals?"

Jan 1, 1966

By Jonathan Peck, Jim Gray

"With the implementation of more advanced monitoring, control and locating systems in surface mines, there is an ever increasing need for their mine-wide integration toward achieving over-all optimization. AQUILA Mining Systems Ltd. is developing the basis for a comprehensive real-time monitoring, control and information system called the Total Mining System or TMS. This system is being designed to address both current and future needs of open pit mines toward improving productivity and minimizing costs, through better two-way information flow between each component in the operation. At a basic level, feedback from equipment and process monitoring will enable decision making to be based on quantitative, on-demand information, thus permitting proactive rather than reactive planning. Dynamic planning would be a valuable tool as market conditions fluctuate, equipment fleets age and variations in the grade, quality, geometry and hardness of the mined material all contribute to either changing production targets or levels of achievable performance. Such a capability could be implemented within the next two years.At a higher level, and within five years, autonomous operation and/or real-time supervisory control of mobile and stationary equipment in open pit mines will be achieved. A discussion is provided in regard to the development and implementation of an autonomous haultruck and blasthole drill, to demonstrate the need for such a system.This paper outlines a preliminary program for the design, development and implementation of this system, primarily in relation to high-level communications and its role in the future automation of open pit mobile equipment."

Jan 1, 1995

By Y. Hanada

Electrorefining at higher current density is desirable due to the increase in productivity attained without expanding the plant size. However, increasing the current density in common commercial practice causes problems such as anode passivation, dendritic deposition, cathode impurities and energy consumption. In general, agitation of the electrolyte is effective in suppressing these problems. To apply the agitation to commercial practice effectively, the method of agitation is important. One possible method is agitation by gas injection. In this study, fluid motion characteristics with gas injection between electrodes were investigated using a water model. Flow patterns were observed and fluid velocity was measured using a particle tracking method. It was found that the time-averaged velocity near the electrode walls was of the order of 0.1 m/s in the conditions. The flow was highly turbulent. The turbulent component of velocity was the same order as the time-averaged velocity. The mass transfer coefficient between the wall and fluid doubled when the effect of turbulent intensity was taken into account. The effects of gas injection on the electrolysis behaviour at high current density were discussed in terms of the mass transfer. It is suggested that gas injection could suppress the problems at high current density.

Jan 1, 2007

By Philip Thwaites

"Automatic flotation control in varying degrees of sophistication is practiced at a number of concentrators throughout the world. Practically, the variable conditions in the flotation circuit and the difficulty in maintaining accurate instrumentation information all add to the complexity of automatic control.Further development at the Kidd Creek concentrator has resulted in a 3075 mtpd copper flotation circuit capable of running twenty-four hours a day under the direct control of an optimizing supervisory computer.Three main streams, continuously monitored by an XRF analyzer, supply circuit information to the optimizing computer. Circuit efficiency calculations (from smelter contract terms) and target setpoints allow the computer to determine the economic optimum direction to move the circuit based on the grade/recovery relationship. Circuit manipulation is accomplished by precise pumping of collector and frother reagents together with accurate control of flotation bank pulp levels. The former uses computer controlled diaphragm pumps and the latter is achieved by control loops utilizing a float type level transmitter, variable position dart plugs and a process computer working to setpoints determined by the optimizing computer.The development of a fully automated flotation circuit is by no means complete, but increased knowledge and major hardware improvements have allowed its progression to a higher level of sophistication.IntroductionThe Kidd Creek concentrator is located twenty-six kilometers east of Timmins, Ontario, within a metallurgical complex including a 109,000 mtpy zinc plant and a 59,000 mtpy copper smelter and refinery. The concentrator treats two ore types, a copper-zinc ore and a copper-silver-Iead-zinc ore, at a combined rate of 4,500,000 mtpy. Flotation of the crushed and ground ore yields copper and zinc concentrates from the copper-zinc ore and copper, lead and zinc concentrates from the copper-silver-lead-zinc ore."

Jan 1, 1983

By J. C. Ingles

"A new technique is in the process of revolutionizing inorganic chemical analysis. Galled atomic absorption spectrophotometry, it combines the use of a special light source, a flame, and the equipment of conventional spectrophotometry, to provide a quick, reasonably accurate method for the determination of a large number of elements.This paper outlines the principles on which it is based, describes the commercial instrumentation"" available for exploiting it, and. summarizes current applications in process metallurgy."

Jan 1, 1966

By F. Y. Hsiao, H. C. Kao

Underground excavation in hard rock is normally stable at shallow depth except for wedge failure. However, the excavation depth is rapidly increasing recently. In high overburden stress condition, the integrity of rock would be destroyed with degrading rock strength. Therefore, understanding both the peak and the post-peak strengths of hard rock are necessary to assess the tunnel stability at depths. The characteristic of the post-peak strength is seldom studied in Taiwan in the past. Various estimation methods for the post-peak strength degradation were briefly reviewed in the paper. Based on the Geological Strength Index (GSI) system is widely used in the determination of the rock mass strength, the quantitative residual GSI system was adopted to estimate the possible strength degradation for a hydraulic tunnel in Taiwan. The Mohr-Coulomb model (no strength degradation) and the post-peak strength degradation model (strain softening model) were used to simulate the excavation of the case tunnel at different depths. The analyses demonstrate that the tunnel is in stable condition at 600m of depth. And the effect of the postpeak strength degradation on tunnel deformation is progressively significant with increasing tunnel depth. Approximate 3-5 times of increase in crown settlement and horizontal convergence would occur when post-peak strength degradation are considered at 2400m of depth. Severe tunnel deformation may endanger the tunnel stability. Modeling results reveal that the post-peak strength degradation has a great effect on tunnel stability under high overburden stress condition, which should not neglect in deep tunnel design.

Jan 1, 2015

By K. V. Konigsmann

"The mill at Mattagami Lake Mines treats 3,850 tons per day. The mill feed is a heavy sulphide ore. It is composed ofPyrite & Pyrrhotite - 40%Marmatite - 17%Chalcopyrite - 2%Magnetite - 10%Talc and other Silicates - 31%The sulphides are intimately associated with each other and often finely disseminated throughout the siliceous gangue. An abundance of middling particles exist in the circuit and a delicate balance has to be maintained between concentrate grades and metal recoveries.The metal content of the mill feed fluctuates between 0.4 to 0.7% for copper and 6 to 13% for zinc.The flow sheet of the concentrator is shown in Figure 1.Eight sample streams have been selected for on-stream analysis, namely1. Copper Concentrate 2. Copper Cln Tailings 3. Copper Tailings 4. Zinc Concentrate5. Zinc Rgh Concentrate6. Zinc Cln Tailings7. Zinc Rgh Tailings8. Flotation TailingsThe mill feed is not being analysed. Only a very coarse sample could be obtained which would be difficult to pump, and the fluctuations in the copper content are too small in absolute terms to have much of a bearing on circuit operations."

Jan 1, 1969

By K. C. Lahiri, H. P. Das, G. G. Sarkar

"The petrographic components of any particular rank of coal often show some distinct physical and chemical characteristics. Therefore, their pro-portionate distribution in a coal greatly influences the technological behaviour of the coal.In any size or gravity separation of a coal, the petrographic constituents become segregated to different degrees in some preferred size or specific gravity range. Therefore, a knowledge of the petrographic nature of the washed and/or screened fractions is often considered essential in selecting the most efficient method for coal preparation and in exploring the proper evenues for its utilization.A graphical method is described in this paper to indicate the mineral-matter content and the petrographic components of the washed fractions of a coal at different ash levels of separation in the form of a new washability diagram. This diagram can be conveniently used to assess or predict the petrographic composition of clean coal or sinks corresponding to any desired ash level in the cleans. With the help of this diagram, it is also possible to locate the yield level of cleans at which maximum enrichment of vitrinites and exinites occurs with the least amount of mineral-matter content."

Jan 1, 1971

By Frank Wright

"The Icon Sullivan Joint Venture ore deposit was discovered in June, 1965 by Messrs. Paul Benard, Bob Galipeau and Mac Watson working under the direction of Mr. Andrew J. Troop, as employees of the Icon syndicate. The deposit is located on the Waconichici River as the south end of Baie du Poste of Lake Mistassini, approximately 45 miles north of Chibougamau. Property acquisition and Winkie drilling was followed by a diamond drilling program to evaluate the deposit. Stripping of the open pit area connnenced in the late fall of 1966 and the first test sample of ore was shipped to Chibougamau in December of that year.Regular ore shipments to the mill of Merrill Island Mining Corporation Limited for concentration commenced May 25, 1967. Production to December 31, 1970 amounts to 42,960,000 pounds of pay copper.The ore is chalcopyrite in white quartz dolomite, and it contains a very small amount of precious metals. The quartz dolomite assumes a flat to gently dipping attitude and is associated with a graphitic argillite contact zone on both hanging and footwall sides, in dolomitic limestone rocks. There is practically no other sulphide present in the ore.During the summer of 1969 a series of pre-concentration tests were completed and a Wemco heavy media sink float plant was installed in late 1969 and early 1970. This pre-concentrator eliminates at least one third of the ore mined in the form of barren quartz dolomite prior to ore shipment by truck to the concentrator in Chibougamau."

Jan 1, 1971

By B. R. Casement

"Managing safety on the basis of after-the-fact reaction to accidents, can never be more than partially successful. Injuries will occur as long as the underlying potential for them still exists. Unless unsafe actions and conditions are systematically decreased, no program can have more than a short-term success.The pro-active Bullmoose loss control process, instead, focusses on heightening awareness of work habits, to prevent incidents by reducing their potential.Any safety program will be doomed to failure if the development of safe work habits depends on the safety supervisor or a safety committee. At Bullmoose the focus is on the critical actions out of which losses emerge. The successful application of performance-related feedback is achieved by taking safety, health, and environmental concerns into consideration on every level, and, by doing the right thing in every job done.What is an Exceptional Loss Control Program?If an accident in an organization creates a flurry of interest, resulting in ""cracking down"" on violations for a short period of time then an ""exceptional"" loss control program exists. Unfortunately, exceptional here does not refer to the effectiveness of quality of the program but to the fact that the organization is managing loss control by exception. The degree of management attention in an ""exceptional"" safety program varies over a period of time, remaining low as long as the rate of losses stays within management's acceptable control limit (Fig. I). When the losses rise above this, management becomes motivated to begin ""exceptional"" efforts to manage losses. When the rate falls again to within the accepted limit, efforts to control losses take a back seat.Such a strategy guarantees that losses will be tolerated or ignored as long as the actual rate is below the acceptable limit. Simply to lower the limit would not reduce losses, but would result in an increased number of flurries of management attention to loss control. This ""on-again, off-again"" style of management teaches supervisors and others that basic loss control is not as important as are statistics."

Jan 1, 1993