Search Documents

By H. H. Gardner

Introduction The Greenhill mine of West Canadian Collieries, Limited, is on the Alberta side of the Crowsnest pass, twelve miles from the Alberta British Columbia boundary-line. Here, five coal seams of Lower Cretaceous age are found in the Kootenay formation. They outcrop on the north and south slopes of the valley, with strike approximately N.30°W., paralleling the main range of the Rocky mountains, and dip about 40 deg. westward. Of the five seams, only two, designated No. 1 and No. 2, have been worked to date. On the West Canadian Collieries property, No. 1 seam ranges in thickness from thirty feet to nil. Generally, it has a hard, strong conglomerate roof. No. 2 seam is separated from No. 1 by forty-five feet of shales and sandstones. It has a thickness of eight to thirty feet.

Jan 1, 1947

By E. L. Bruce

EUROPEAN Russia is mainly a great plain, the average elevation of which is only 600 feet above sea level and the maximum elevation less than 1,200 feet (Figure 1). The main divide between the Arctic ocean and the Black sea and Caspian sea is an indistinguishable topographic feature from which the Dneiper and Don rivers flow southward to the Black sea and the Volga river to the Caspian. The valleys of these rivers are but little below the general level (Figure 2). To the south, this great, rolling plain is broken by a low ridge of Precambrian gneisses and intrusive rocks. The Crimea is an upland from which the descent to the Black Sea coast is precipitous (Figure 3). The Ukrainian Soviet Socialist Republic occupies the southern part of the plain. It is the southwestern unit of the Union, bordered by Rumania and Poland on the west and by the Crimean Soviet Socialist Republic on the south.

Jan 1, 1938

RISKGATE is an interactive online risk management system developed by the Minerals Industry Safety and Health Centre (MISHC; University of Queensland) to maximise health and safety performance in the mining industry through implementing continual improvement in management of major unwanted events. A comprehensive knowledge base has been captured for risk management of tyres, collisions, fires, isolation, strata underground, ground control open cut, explosions, explosives, manual tasks and slips/trips/falls. This will be extended to outburst, coal burst and bumps, interface displays and controls, tailings dams and inrush in 2013. RISKGATE presents substantive and leading edge controls to assist industry stakeholders in the design, management and reporting of organisational and regulatory compliance requirements. From a broader industry perspective, RISKGATE provides an environment for knowledge capture and knowledge exchange to drive innovation and best practice in the identification, assessment and management of risk. By capturing operational knowledge from industry experts, RISKGATE provides a cumulative corporate memory at a time of high personnel turnover in the coal industry. All major Australian mining companies are contributing topic experts to this broad industry initiative. In the first 24 months, nine coal mining companies nominated over 80 different experts who contributed over 400 days of individual time to the knowledge capture workshops. RISKGATE is the largest single Australian Coal Association Research Program (ACARP) occupational health and safety (OHS) initiative to date.

Aug 1, 2013

By Marc-André Villiard, C. St-Onge, V. Silla, J-C Milot

Rio Tinto Fer et Titane (RTFT) operates a metallurgical complex in Sorel-Tracey, Canada. In the Ore Preparation Plant (OPP), ilmenite ore is roasted through four parallel rotary kilns generating 95% of the plant wide sulphur dioxide (SO2) emissions. RTFT proactively set an annual emission cap for SO2 to be achieved by 2015. To achieve this targeted SO2 reductions, a technology evaluation and selection exercise was carried out, followed by detailed engineering and implementation. After a detailed evaluation of SO2 scrubbing technologies, the Circulating Dry Scrubber (CDS) system was selected as the most appropriate desulphurization system for this application. The system was implemented and commissioned from 2013 to 2015. General performance testing conducted in May 2015 demonstrated that the system achieved and surpassed the anticipated design values in terms of SO2 removal efficiency and hydrated lime utilisation. This paper summarizes the SO2 technology selection process, design features of the selected technology, project implementation and final performance testing of the SO2 abatement system.

Jan 1, 2015

By Nancy C. Mohn

?Even though the age of many existing coal units exceeds 30 years, these units continue to perform with excellent reliability and at a competitive cost with other fossil fuel units. ?NERC data shows a consistent increase in availability for all utility coal generation ?With the opening of power markets, the challenge for coal is to produce competitive electricity while meeting increasingly stringent, and costly environmental limits. ?During the 60s and 70s, subcritical steam power plants dominated the market. The emphasis was on scale-up to larger MW size units. ?In the last decade, we have seen interest in a broader set of technologies with new drivers: ?Fluidized bed technology was developed to respond to increased environmental requirements, particularly with lower quality fuels ?Supercritical pressure units have gained interest for both fuel cost savings and reduced emissions due to higher efficiency.

May 1, 2001

By D. H. Flather, J. W. Hendry, K. Drover

Black Hawk Mining Inc. has completed a comprehensive program on the prediction and management of acid rock drainage (ARD) at their Keystone Gold Mine (Keystone) near Lynn Lake, Manitoba. The program, initiated in 1994, followed a phased approach utilizing initial acid-base accounting (ABA) results and subsequent laboratory kinetic testwork to define site-specific sulphide oxidation and neutralization consumption rates in waste rock. Net acid generating waste rock at Keystone was defined through the kinetic testwork as waste rock yielding a net potential ratio (NPR) of less than two. A preliminary waste rock management program based on blending of potentially acid generating and acid neutralizing waste rock was advanced. Subsequent refinement of the management program followed the analysis of over 1580 ABA samples collected from individual blast holes during the initial bench development phase of the Keystone pit. Uncertainties in actually achieving adequate blending within the dumps at a mining- scale resulted in the development of a revised waste rock management program based on segregation. Recognizing that any successful management plan requires that the ARD characteristics of the waste rock be identified prior to in-pit blasting, the extensive ABA database was utilized to develop a rapid characterization scheme. By implementing a characterization scheme based on total sulphur concentrations and fizz rating, waste rock could be quickly segregated without delaying the natural flow of ore from the pit. Interestingly, it also became apparent that gold values were strongly correlated with total sulphur, such that traditional fire assays were supplanted with a simple and more cost-effective total sulphur determination. The program highlights the importance and benefits of collecting and exploiting data beyond that necessary to acquire appropriate development permits.

Jan 1, 2000

By C. F. Chung, F. P. Agterberg

"Prediction of a variable sulphur content in Cape Breton seams is important for planning the production of a highgrade metallurgical coal. Two extrapolation methods (Kriging and a version of Universal Kriging) to predict sulphur content in blocks of coal before mining are presented and applied to the New Lingan Mine reserves in the Harbour seam. The uncertainty of the predicted values is expressed by using standard deviations. Some statistical results for the Phalen seam, which occurs about 400 ft below the Harbour seam, are presented for comparison. The two mathematical models consist of two sets of equations which have been used in computer algorithms. Some limitations of the present approach and possibilities for further statistical work are indicated."

Jan 1, 1973

By D. G. Champion

"A comparison of diesel engine power ratings with in-service capability, and the selection of unit size and total number of units are discussed in the paper. Engine specific fuel consumption and its evaluation in relation to manufacturers' tolerances and equipment load factors is reviewed along with the suitable plant layout. The potential for heat recovery is discussed in connection with simple and operable recovery systems f or exhaust and cooling circuits. Maintenance standards as related to improved reliability and reduced fuel and operating costs are also outlined. IntroductionDiesel generators are used in Canadian mining operations to provide electrical power for "" base- load"" requirements in some instances and for ""stand-by"" or ""emergency"" power in almost every producing mine in the country . There are over 300 mines in Canada of which only a handful have to generate their own electricity. Only one or two mine s enjoy access to a hydroelectric site. Consequently, the diesel engine is the principal prime mover because of its high efficiency relative to other prime movers in the size range in question.The author has been associated with several “base-load” plants in addition to participation in numerous projects requiring emergency diesel generators. Records indicate that engine performance in term s of reliability and efficiency lags behind other industries where the diesel engine is used more extensively, such as the shipping industry which is able to make a more prudent selection of original equipment and enjoy easy access to highly skilled operating and maintenance personnel. It is hoped that the contents of this paper will be of value to Canadian operators of diesel generators, in the generation of prime power or applications for back-up power."

Jan 1, 1986

By W. D. Breil, C. B. Ison

A collection of general performance data relating to the G.H.H. - Gutehoffnungshiitte multi-rope friction hoist will be discussed together with some aspects of the following: overspeed supervision by a pantam device as opposed to the lilly type of fly ball control, automatic control systems, multi-disc braking, generator and motor winding, constant temperature monitoring, the development of an automatic hoist-rope lubrication system, and the control of rope tensions by the installation of G.H.H. - Gutehoffnungshiitte hoist rope fine tensioning units.

Jan 1, 1972

By John G. Kelly

"In 1982 an extensive study was carried out to determine the best means of size reduction for the ore to be hoisted through the borehole hoisting system at Sherritt Gordon's Fox Mine.The study examined three alternatives:1. a jaw crusher,2. pneumatic rockbreaker(s) at a grizzly, and3. hydraulic rockbreaker(s) at a grizzly.The final decision was a compromise between alternatives 2 and 3. Two rockbreakers, one pneumatic and one hydraulic, were installed over a single grizzly. Some modifications have been made to the system, but over-all it has operated at acceptable levels since its installation in July 1983.As all the ore passes through a jaw crusher before being hoisted to surface, an evaluation of the relative performance and cost-effectiveness of the jaw crusher and the two types of rockbreakers is possible. This paper outlines the initial study, and compares the three breaking systems in operation at Fox Mine.IntroductionThe Fox Mine of Sherritt Gordon Mines Ltd. is located 800 kilometres north of Winnipeg near Lynn Lake in Northern Manitoba. Production at the copper-zinc orebody began in 1970 at a rate of 3,000 tons per day. Over 12.5 million tons will have been hoisted from the underground mine when the ore reserves are depleted in October 1985.The mining method at Fox Mine is sub-level open stoping with delayed backfilling are from the upper level stopes, above the 2000 level, is mucked on the main levels established at 400-ft elevation intervals, and is fed through a central orepass to the crusher located on 2100 level. Production in the lower levels commenced in 1975, and ore from the 2200 and 2400 level stopes was hauled up a 15010 ramp by 26-ton trucks to the 2000 level orepass dump. Projected production rates from the 2600 and 2800 levels using the trucking system were too low, and therefore, in 1983 a borehole hoisting system was commissioned to hoist that ore'!'. One thousand tons per day of ore are skipped through an 8-ft diameter borehole from the 2650 level loading pocket and dumped on the 2000 level. The ore is transferred by LHD to the main orepass for crushing before being conveyed to the main shaft for hoisting to surface (Fig. 1)."

Jan 1, 1986

By W. E. Segsworth

Introduction By far the largest part of the money raised for mining is raised by honest and legitimate means; but a not inconsiderable amount is raised by fraudulent sales methods. It will be conceded without argument that the greatest menace to the mining business is the fraudulent promoter. The sale of worthless mining stocks to the public by high-pressure. salesmen, house to house canvassers, telephone campaigns, fraudulent use of the mails, fraudulent statements, and reloading, has seriously prejudiced the public against even legitimate mining. A very small percentage of the funds raised by such fraudulent means is ever spent on the property, but instead is absorbed by the promoter in illegitimate' profits, enormous commissions, high office rents, and other expenditures, and is just so much subtracted from the fund which the legitimate developer needs to bring new mines to the point of production. The mining fraternity has been at fault in that, while they recognized this situation, they made no adequate attempt to rectify it. They knew that these fraudulent practises were conducted by parasites who attached themselves to the mining business in boom times and claimed to be part and parcel of it, but who were merely professional salesmen and promoters who, when there was not a mining boom, were selling sky-line real-estate, worthless oil stocks, or fraudulent securities which happened to be popular with the public. While mining people had this distinction well in mind, the public did not differentiate between the crooked promoter temporarily selling fraudulent mining stock and the honest promoter who made mining finance his life work; and we did little to make this distinction clear to the public or to sweep these money grabbers out of our house. The historic boom of 1927-8 and '29 brought with it the usual crop of crooked mining promoters, and the scandals resulting from their operations forced the Governments into the enactment of laws to attempt to protect the gullible public against the operations of these meanest of thieves and to appease public clamour.

Jan 1, 1934

By Adrian Dance

The Antamina orebody is a geologically complex, polymetallic skarn located in the Peruvian Andes. A range of copper and copper-zinc ores are campaigned separately through the concentrator producing copper and zinc concentrates as well as lead and molybdenum by-products. Ore type classification at Antamina is based on chemical assays; geological or lithological variations are not considered. Consequently, each ore type demonstrates a wide range of concentrator performance. Antamina is currently implementing a system to track ore movements from the shovel face to the concentrator. Relatively sophisticated models of the ROM and coarse ore stockpiles ahead of the mill will be used to account for the variable delay between mining and milling. One of the numerous benefits of ore tracking is the ability to directly associate the measured concentrator performance with a physical location in the orebody. Using existing mine planning software, three-dimensional models can be created of such performance measures as metal recovery, concentrate quality, operating cost and reagent consumption. Such a database of information allows the true value of different ore sources to be determined. The value of an ore source is conventionally measured as metal content (individual or combined ?equivalent?) with a cut-off grade applied to indicate some base level operating cost. However, the true value of an ore source should include dynamic factors like haulage cost, reagent use, smelter penalties and even prevailing metal prices. If an ore source is considered from all perspectives rather than simply its potential to deliver value, the concept of ?ore? becomes more flexible. Any ore source that reveals itself to be unprofitable can be eliminated from the mine plan or possibly blended with others to improve its value. The ability to predict mill performance ? and thereby profitability ? is a powerful tool. In an operation such as Antamina, where managing ore sources, campaigns and the delivery of a variety of concentrates in a narrow timeline to customers is a daily challenge, prediction is the key to success and improved efficiency.

May 1, 2003

By S. Leong

This paper reports on research examining disclosures from mining companies regarding their water usage in the Macquarie and Lachlan catchment areas, both parts of the Murray-Darling Basin in New South Wales, Australia. The objective of the research was to assess whether this disclosure is sufficient to allow communities to determine whether mining companies are complying with mining conditions of consent and abiding by the requirements of their water licencing agreements. These requirements are then compared to the water reporting requirements of the Global Reporting Initiative (GRI) and the Water Accounting Framework for the Minerals Industry (WAFMI). Communities are concerned about whether the mining industry?s use of water will have impacts on their livelihoods and lifestyle and thus require information concerning the quantity of water that will be extracted, how much water will be left for other stakeholders and whether the mining will affect water quality. This is an archival study. It has involved examining relevant publically available information released by mining companies and government regulators and determining if this is sufficient to meet the needs of the local communities. Additionally, it has involved looking at information indirectly provided by mining companies, via the use of intermediaries. Further, information availability concerning basic water accounting and regulatory breeches and whether such information is available at the mine site level has been considered. It is found that while NSW legislation places very little reporting requirements on mining companies, the development consent conditions for new projects and extensions to existing projects are quite significant and should be sufficient to meet the needs of local catchment residents though such information is not always easily accessible for the layperson.

Aug 1, 2013

By F. Chiesa

Experimental results on thin and thick castings poured in aluminum A356 and magnesium AZ91E by the low pressure permanent mold process have been compared to the result of filling simulations for thin and thick castings. If the results of modeling is reliable when the liquid remains above the liquidus temperature, this is no longer the case when partial solidification occurs. The visco-elastic behavior of a partially solidified liquid is difficult to put into equation as it depends on the amount of shear it has been been subjected to. Attempts to predict misruns with a commercial software has been proven to be very difficult if not impossible; divergence of the numerical solution has been observed unless prohibitively long computing times are used. In order to overcome these difficulties from a practical standpoint, a simple method is proposed which consists in tracking the temperature of the advancing liquid metal front so as to make sure it will always be above so-called `Misrun Critical Temperature' (MCT) determined experimentally for thin and thick aluminum A356 and magnesium AZ91E castings. If the liquid metal front falls below this temperature, a cold-shut or misrun is likely to happen at this location. The values of MCT for thin and thick in aluminum A356 and magnesium AZ91E were determined experimentally on misrun castings of extreme geometries (a thin 2.5 mm wall cover and a 6mm to 25 mm thick bell housing). MCT was found to be lower for magnesium AZ91E and for the thicker castings.

Jan 1, 2011

By A. Henk, C. M. Aruffo, K. Fischer

"Geomechanical reservoir modeling offers a valuable tool to predict tectonic stresses, in particular the local perturbations in orientation and/or magnitude which occur at lithological boundaries and faults. The paper presents a workflow for building and calibrating such geomechanical models. The numerical simulations are based on the Finite Element method and can range from field-scale models to smaller, highly detailed submodels of specific fault blocks. The approach considers the reservoir-specific characteristics with respect to subsurface geometry (lithostratigraphic boundaries, faults), mechanical properties and ambient stress field. During the subsequent calibration stage calculated stresses are compared to stress data actually observed in borehole data. Poorly constrained input parameters are iteratively modified within reasonable limits until a satisfactory fit between calculated and measured stresses is achieved. This validated model can then be used for stress predictions between wells and in undrilled parts of the reservoir, respectively. The workflow is applied to two case studies - a large gas field in Northern Germany and a CO2 sequestration project in Australia – to test and illustrate its practical value. INTRODUCTIONDetailed knowledge of the tectonic stress field is crucial for the optimal exploration and use not only of conventional and unconventional hydrocarbon reservoirs, but also for deep geothermal reservoirs, carbon capture and storage (CCS) projects as well as underground mining and nuclear waste repositories. Any reliable stress prediction is hindered by the observation that the magnitude and orientation of the stress field can vary significantly – not only in time, but also in space. Such spatial stress variations comprise all scales, i.e., from the scale of lithospheric plates down to the grain-scale. On the reservoir- and fault blockscale, the local stress field can be influenced by faults and different mechanical properties of lithologies (Sassi & Faure, 1997). The resulting variations in stress magnitude and/or stress orientation are commonly referred to as stress perturbations and give rise to a unique, reservoir-specific stress pattern (Yale, 2003). Thereby, local stress fields can deviate by up to 90° in orientation and several tenth of Megapascal (MPa) in magnitude from regional trends."

Jan 1, 2015

By Ajit K. Sinha

"Abstract - Electromagnetic surveys were conducted over the Yava sandstone-hosted lead deposit in Nova Scotia to evaluate the usefulness of such surveys for detecting and mapping sedimentary­ hosted metallic ore deposits. Both transient and multifrequency systems were used for that purpose. The deposit consists of three zones of disseminated galena which also contain minor amounts of pyrite and sphalerite filling the interstices of the sandstone grains. Each zone overlies a basement depression and is separated from the adjacent zone by an intervening basement high. A conductive shale layer underlies the galena-rich sandstone formation at all three zones.Because the concentration of galena (3% to 4% ) and other sulfides is too low to affect the resistivity of the sandstone formations for detection by ground electromagnetic (EM) methods, the strategy for our survey was to look for areas of basement depressions and the presence of conductive shale in those depressions by EM depth soundings. The presence of the galena-rich sandstone formations could be inferred because of the close association of these two features with the deposits in the Yava area. Both transient and multifrequency EM systems were successful in mapping the basement depressions and detecting conductive shale at the three known mineralized zones. The technique, therefore, seems to offer good prospects for mapping similar stratabound sedimentary-hosted sulfide deposits."

Jan 1, 1993

By M. Li, T. H. Dubaniewicz, H. N. Dougherty

"INTRODUCTION Underground mines have the risk of accumulation of gases if not ventilated properly or during and after emergency situations when ventilation controls become damaged or stop working. Common gases that are monitored in underground coal are carbon monoxide (CO), oxygen (O2), and methane (CH4). Methane is a gas found in coal and released through mining; its explosive range is between 5% and 15%. Methane is commonly monitored on all mining equipment and with handheld gas sensors carried by most underground coal miners. Fiber optics (FO) is a popular technology applied in underground mining, particularly for its electric isolation. Many miners are familiar with FO cables hung throughout the mine, which are primarily used in the communication of voice and data (Taylor et al. 2010). Advancements in laser and fiber optics have made this technology well suited for gas sensing the harsh environment of mining applications. The work of the U.S. Bureau of Mines on the use of fiber optic monitoring of gases in mines started in 1992. Dubaniewicz et al. (1992, 1993, 1995, 1999, 2003) developed prototype gas sensors, including methane gas sensors, for research purposes. Previous research (Dubaniewicz & Chilton 1992) identified potential fiber optic gas detection cross-sensitivities associated with the index of refraction of various gases. Index of refraction effects was noted for carbon dioxide (CO2), which is produced in significant quantities by mine fires or explosions. NIOSH released a broad agency announcement (BAA) for the development and demonstration of mine safety and health technology (CDC NIOSH 2017). The objective of this announcement was to validate a sensor, specifically fiber optic, for the mine environment and test it in an actual working mine. The RSL FO sensor “OptoSniff” provided from this work is capable of hundreds of sensing points over distances of up to 20 km, has a measurement range of 0.05% to 100%, senses in an oxygen- deficient environment, and has no gas cross-sensitivity (RSL, 2014). The RSL system is totally electrically passive outside the central control unit (CCU), which can be housed in an MSHA-approved explosion-proof (XP) enclosure or in a control room outside of the permissive area. The sensor was tested in dusty and signal loss situations, showing it is tolerant of dust, has functioned at signal losses up to 90%, and was successfully tested in a mine environment for a five-month period (Walsh et al. 2014). This paper describes how the RSL FO sensor is used for testing using smoke and its contaminants for applicability in emergency situations. The testing investigates individual contaminants such as CO2, temperature, and smoke. Each test was performed separately and methane concentration, laser power, and response time data were collected."

Jan 1, 2019

By E. B. Wilson

"Although the Operations Research technique of Reliability Theory has been applied with marked success in many fields, including the Apollo spaceship programs, the concept of reliability has not been generally adopted in mining and other heavy industries. Of course, reliability, or the probability that a system will be able to operate without a failure for a given interval of time, does not require the same emphasis in mining as in the aerospace industries. Nevertheless, certain aspects of Reliability Theory can be followed advantageously. For example, reliability calculations can determine the best time to overhaul and whether to retain stand-by units.The usefulness of the pseudo-operations research technique known as Replacement Theory is more readily re-cognized by the maintenance engineers in mining and other heavy industries. One of the least complex models enables the optimum Lifetime of an asset to be determined."

Jan 1, 1970

By N. Shi, T. G. Joseph

ABSTRACT: An interactive cable shovel simulation has been developed to mimic any shovel dipper geometry for a given cable shovel operating in any homogeneous face material. This interactive cable allows the user to predict shovel performance in any face material encountered and track both its ground stability and the dipper-ground interaction. An embedded Microsoft® Visual Basic spreadsheet was used as the platform for developing an interactive simulation that allows for maximum user-defined parameter input and interactive visual output. The result is an analytical dipper-ground interaction solution that yields crowd, hoist, and digging effort as a function of face activity position.

Jan 1, 2011

By Michael J. Beus

The National Institute of Occupational Safety and Health-Spokane Research Laboratory (NIOSH-SRL) have developed a Shaft Conveyance Monitoring System (SCMS). Assessment of current hoisting technology has shown that monitoring wire rope tension and conveyance position and load directly from the skip or cage top offers several significant safety, production, and maintenance advantages. The SCMS consists of conveyance position and guide displacement sensors, a battery power supply and charging system, and a new sensor to measure hoist rope tension. This device provides a warning of the occurrence of ?slack rope? a particularly dangerous condition. A 2.4 GHz radio link transmits data to the hoistroom. A reduced scale hoisting test facility has been constructed to test these components prior to field trials. The advantages of monitoring wire rope tension and conveyance position and load directly from a skip or cage top will be discussed. Field tests are underway in full-size shafts to refine the concept and evaluate long-term reliability and maintenance requirements. Application of this technology may result in decreased maintenance costs as well as safer, more productive hoisting operations.

May 1, 2001