Search Documents

By J. H. Archibald

"IntroductionShot-saws are used for sawing rock throughout the dimension stone industry especially in granite quarry mills. Shot-saws, as currently designed, have an inherent wear problem which leads to slow cutting rates and repetitive blade changes which consumes much time. Because the saw blades are made from steel the abrasive shot used with them is limited to a certain hardness which effects the over-all efficiency of the sawing operation. Suggestions are made toward optimization of blade design and the sawing process. Blade DesignA common steel blade design is shown in Figure I. Note the perforations in the blade. These perforations or holes in the blade serve two or three purposes. The most obvious reason is to allow the abrasive shot a pocket in which to collect at the bottom of the blade, so that it can be distributed from these pockets into the cutting zone underneath the blade. The abrasive is fed to the saw in a slurry and usually comes in from the top. The blade must then cut a kerf wider than itself in order that the abrasive grains have a path leading from the top of the blade, down along its sides, and finally reaching the pockets and cutting zones. This circuitous path followed by the abrasive leads to side wear on the blades and high friction which can lead to blade buckling in severe cases. However, the fluidized path of the abrasives down the sides of the blade serves another purpose which is a positive gain if conditions are properly controlled. The abrasive slurry interacts with the perforations of the blade, the blade itself and the rock. This gap and the perforations in the blade, which are fluid filled, are sites of constant shearing motion. Eddy currents form in these gaps and pockets which tend to stabilize the blade by setting up balanced hydrodynamic forces which otherwise might not form in a non-perforated blade. A stable blade produces a more uniform cut in the rock. The third and final reason for the perforations are to allow the blade to wear in such a fashion that new pockets are always being formed and, consequently, new cutting surfaces between these pockets are also formed."

Jan 1, 1993

By Yannis Faitakis, Simon Bergeron

"This paper describes the implementation of model-based predictive control (MPC) on a vacuum heat exchange network at Alcan's Jonquière Complex. The plant produces alumina from bauxite ore using the Bayer Process.The MPC system was commissioned in 2000, by Alcan personnel and an Advanced Control Engineer from Matrikon. The application has achieved an uptime of about 97%.The benefits were:• Energy savings : 0.5% - live steam reduction• Reduced variation: standard deviation of key temperatures reduced by 50%• Plant throughput increase: via the automated use of surge tanks• Decreased supervision time: by plant operations• Faster and easier diagnosis of problems and plant constraintsThe benefits were higher than expected with a payback time around 12 months.The purpose of the vacuum heat exchange network is to recover energy from a hot stream (pregnant liquor) by transferring it to a cold stream (spent liquor). The system is very tightly coupled, and the main constraints of the multivariable control system are: • to control the many tank levels involved in the process (8 tanks)• to maximize the temperature of the heated streams (spent liquor)• to prevent cooled streams (pregnant liquor) from cooling to below a minimum temperatureThe system includes 9 manipulated, 14 controlled and 2 feedforward variables.The advanced control implementation runs under an expert system environment and provides added flexibility to the overall control strategy."

Jan 1, 2003

By R. Q. Honaker

It has been shown that naturally hydrophobic carbonaceous materials such as coal and graphite can be selectively coagulated and separated from hydrophilic impurities without using oily agglomerants, flocculants or electrolytes. The coagulation occurs at C-potentials significantly higher than those predicted by the classical DLVO theory, suggesting that it is driven by the hydrophobic interaction. In the present work, the energy barriers for the coagulation of a hydrophobic coal sample have been calculated using the extended DLVO theory which incorporates the hydrophobic interaction energy in addition to the dispersion and the electrostatic energies. For the coagulation of minerals present in the coal, the classical DLVO theory has been used for the energy barrier calculation. The results of these calculations provide an excellent correlation with the results of a series of Selective Hydrophobic Coagulation (SHC) tests conducted with run-of-mine coal and graphite samples.

Jan 1, 2004

By Mario Gerards, Axel Wellendorf, Arulnesan Rajesh

"In times of increasing energy cost and global demand for improved machine technology, the optimization of industrial mineral processes in terms of efficiency and production cost is an important factor when choosing industrial equipment suppliers. Of course this applies for screening machines, feeders and distributers as well!Besides of the ability of a screening machine for being adjustable to changing requirements during the production process itself, it becomes more and more important to choose the correct screening machine type, peripheral equipment for arising screening tasks and to optimize the overall design of the screening machine starting at a very early stage.The different types of screening machines bring many advantages and disadvantages with them. The selection of the correct type of screening machine can improve the flow rate, energy, efficiency, yield, quality, output, availability and decrease the maintenance costs and structural steel work.The machine optimization has to be a consecutive process in which at any time results of simulation and “real-life measurement” are compared and the findings are implemented in machine development and design. As an example, it is possible to reduce machine weight and reinforce the steel structure of a screening machine at the same time, which enables the manufacturer to use smaller drives for the screen.This paper will present the methods ANSYS and 3D Solid Works used at RHEWUM GmbH for this way of optimizing machine design and construction and examples for results gained from this continuous improvement process."

Jan 1, 2016

By Goutam H. Shahani

Today, the mining and mineral sectors are being impacted by highly fluctuating supply ? demand, extreme price volatility and tremendous market uncertainty on a world-wide basis. This pattern is expected to continue for the foreseeable future. In particular, large consumers of tonnage quantities of industrial gases (oxygen, nitrogen) all have to make informed investment decisions in this uncertain economic environment. Plant owners ? operators need to carefully examine their current and future industrial gas needs in order to develop the most cost-effective industrial gas plant configuration. This can be done by partnering with an experienced engineering company that offers a complete technology portfolio for producing industrial gases. Ideally, the mineral and engineering companies have to work together as a single team to identify the most efficient and economic plant design. This includes an in-depth assessment of capital and operating costs, in order to deliver an optimal solution, taking plant reliability and process safety into account. It is important to consider all the industrial gas needs at a given manufacturing complex, in conjunction with available utilities and infrastructure to develop the best possible long term solution. Oxygen (O2) requirements include: oxygen enriched and oxy-fuel combustion, smelting and hydrometallurgical operations. Nitrogen (N2) is used for annealing. All of these industrial gas requirements have to be examined at a given site over a long term horizon in a holistic manner. Cryogenic air separation was first practiced at a commercial scale in 1902. Since then, the technology has been constantly refined to reduce cost; and improve reliability and flexibility. Today, using advanced engineering techniques, including proprietary process simulation, and modern fabrication techniques, it is possible to build air separation plants that are both low cost and high quality at the same time. It is important to work with an engineering company that owns a complete portfolio of industrial gas technologies, functional engineering capabilities and a variety of plant solutions. Such a partnership can quickly identify a ?sweet spot? for a given situation. By drawing on experience gained from hundreds of projects, it is possible to quickly optimize a given requirement. In situations where a customer wants a complete solution it may be appropriate to provide an air separation plant on a turn-key basis. This will enable the mining and mineral processor to focus on their core business. By using global procurement and construction capabilities it is possible reduce cost and improve project execution, thereby making industrial gas plant procurement simpler and cheaper for the mining and mineral sector.

Nov 1, 2011

By S. Stefanizzi

In the present paper, numerical simulations based on a finite/discrete element approach are used to study deformation and failure process during standard rock mechanics. FEM/DEM modeling has been used as available with the ELFEN code, which explicitly model the transition from continuum to discontinuum. The transition is simulated through a crack nucleation and propagation that obeys to the Griffith?s failure criterion. If the fracture criterion within the intact rock (represented by FEM) is met, a new crack (represented by DEM) is initiated. Remeshing allows the fracture process through the FEM mesh to be tracked and visualized, thus contact properties can be assigned to pre-existing fractures and newly generated fractures. In this study, compressive tests of rock samples are simulated. The applicability of ELFEN to properly and efficiently simulate typical laboratory rock mechanics tests, with reference to the rock fracture process, is described in detail. In addition, an indirect validation of the extensional strain criterion proposed by Stacey (1981) is given.

May 1, 2009

By G. Beckstead, L. F. Sawatsky, R. Nutbrown, D. Long, G. Gould

"This paper presents a case study for optimizing water management at Gregg River Coal Mine located near Hinton, Alberta. The optimization study was derived based on a review and assessment of existing management practices and plans for future operation and final reclamation. A proactive water management strategy was developed to assist mine staff in adopting a rational, environmentally sound, and economical approach to water management. A plan was developed to provide for safe operation, self-sustaining operation, low maintenance, minimum negative environmental impacts, and anticipation of future needs for existing and future operations. A plan for final reclamation drainage was developed including establishment of effective, sustainable, and maintenance-free water management systems. The study demonstrated the importance and benefits of a proactive approach for integrated mine water management. This approach is recommended for other similar mine operations because it will improve environmental compliance and reduce costs of water management. IntroductionGregg River Resources Ltd. (GRRL) operates an open pit coal mine on the eastern slopes of the Rocky Mountains, located about 45 km south of Hinton, Alberta. GRRL opened the mine in 1982 and expects to continue operations after Year 2000. GRRL has progressively reclaimed the disturbed area and expects to complete mine-land reclamation shortly after mining in the area is complete. The existing disturbed area and reclaimed area covers approximately 9.5 km2 and will expand to about 10.5 km2 upon mine closure.Like other coal mines in the mountainous areas of Alberta and British Columbia, the GRRL coal mine is subject to highly variable temperatures and moisture conditions. Average monthly precipitation varies from a low of 12.6 mm in January to a high of 113.0 mm in August, based on the precipitation record at the mine site since 1982. Despite the relatively high rainfall during the spring and summer months, excess water problems during rainfall events are quickly replaced by water deficit conditions during periodic droughts. Surface runoff varies from near zero in the winter to a mean annual monthly maximum of 78 mm during the month of June. The mean annual surface water yield is 345 mm."

Jan 1, 1997

By N. Campbell

"The fault under consideration follows a northerly trend past the west; side of the original settlement of Yell ow knife; which is situated 600 miles; north of Edmonton and 400 miles from the Northern Alberta Railway; terminus at Waterways; Alberta. The mining properties chiefly concerned; include the southern part of the Giant claims; on the east side of the fault; and the Con-Rycon-Demelt claims; on the west side 3 1/2 miles to the south.; Geological data were also obtained from the eastern part of the A.Y.E.; property; which lies south of the Giant claims; and from the Negus; Meg; Yellorex; and Kam properties; which are south and southeast of the ConRycon-; Demelt claims (see Frontispiece; also Fig. 5).Recognition of the major faults in the Yellowknife Bay area, including the West Bay fault, which appears to be the greatest, resulted from the work of A. W. Jolliffe (formerly of the Geological Survey of Canada) in 1935 and subsequent years. It has been stated with little exaggeration that these faults rank with the largest known steeply dipping dislocations of the earth's crust.In the winter of 1939, a mineralized shear zone named the 'Creek vein' was found on the Giant property. It was noted that the space relationship between this shear zone and a body of quartz-feldspar porphyry is roughly the same as that between the Con C-4 shear zone and a body of acid flows lying north of the Con property. Coupling this relationship with the assumption that the movement along the fault is dominantly horizontal, it was postulated that the Giant shear zone represented the faulted extension of the Con C-4 shear zone.As geological information became more extensive, certain weaknesses in this concept became apparent, and when spectacular orebodies were discovered on the Giant property in 1944 the question of possible faulted extensions became an important consideration. Consequently, in the spring of 1944, an extended investigation was undertaken, the results of which are embodied in this paper."

Jan 1, 1954

By Chris M. Healey

"Abstract - Perhaps the single most significant variable in the evaluation of a mining project is the reserve estimate. Many parameters are considered when estimating reserves, among them geology. This paper examines the link between the quality of a reserve estimate and a good understanding of the geological controls for the deposit. A clear understanding of the geometry is essential to the accurate definition of the shape and size of the deposit. This includes the definition of any structural controls as well as the proper interpretation of the stratigraphy. Further when the distribution of grades is erratic and there is consequently a high nugget effect, there are significant problems in estimating the true grade of the deposit.Two Saskatchewan examples are presented, one with good knowledge of the controls and therefore good estimates of reserves, and the other with a poor understanding of the geology and resultant problems in deriving good estimates. In both cases the reserve estimates at various stages in the project development are compared to actual results from underground work. The first example is the Star Lake Mine where just about all the estimates were within 10% of the actual on both tonnage and grade. The Laurel Lake deposit is discussed to show how problems in interpreting the geological data make reserve estimation very difficult. Laurel Lake has the additional problem of erratic grade distribution."

Jan 1, 1992

By Murray Pearson, Jack Murray

"The danger of autoclaves lies in the high temperatures and pressures that exist in autoclave vessels. The usage of autoclaves will continue to expand in the mining industry because of their efficiency and environmental friendliness. But increasing attention must be paid to ensuring their safety. Safety Instrumented Systems (SISs) play a critical role in autoclave plants by detecting potentially dangerous conditions, taking the plant to a safe state, informing the operator about the plant status and the cause of the trip and expediting safe plant restart. The SIS should ideally be fully integrated with but functionally independent of the Basic Process Control System (BPCS) and provide redundant logic solvers to increase safety and plant availability while reducing spurious trips.INTRODUCTIONWikipedia defines an autoclave as follows: “An autoclave is a pressurized device invented by Charles Chamberland in 1879 designed to heat aqueous solutions above their boiling point to process materials.” A typical autoclave system used in the metallurgical industry includes, besides the autoclave vessel, heat recovery (heater) vessels, high pressure positive displacement (HPPD) feed pumps, vessel lining systems, specialized internals and components, agitators, pressure letdown or flash vessels, isolation and control valves, over 2,000 I/O points and related instrumentation, and emergency relief systems."

Jan 1, 2009

By A. McLean, W. Q. Chen, W. Yan, M. Barati, Y. D. Yang

In order to maximally remove the harmful impurities phosphorus and reduce the loss of valuable elements from Si-based alloy for production of solar-grade silicon, thermodynamic properties of the Si-based alloy were studied. In this work a new model, the Molecular Interaction Volume Model (MIVM) derived from statistical thermodynamics, was successfully used in the Si-based and Si-Fe-based alloy. The calculation started from binary Si-Fe, Si-P and Fe-P systems, then the thermodynamic parameters of ternary systems could be derived based sub-binary systems. Using the activity coefficients of the elements in the Si-based alloys and the saturated vapor pressure of the pure substance of the components, mass fraction of P during vapor-liquid equilibrium can be calculated. The calculated thermodynamic parameters were compared with experimental data available in different publications, and it is found that the thermodynamic parameters calculated using MIVM model are in good agreement with the measured results. The calculated result shows that the mass fraction of phosphorus during vapor-liquid equilibrium of Si-Fe-P melt increases with the increasing phosphorus content and decreasing temperature. This is an important direction for experimental practice in vacuum or low-pressure EML refining of ferrosilicon for potential production of solar-grade silicon without significant vaporization loss of valuable element.

Jan 1, 2015

By Ken Musgrave

"What Most Effective Management Does?It must satisfy the demands, of three groups of people: owners, employees and the public.OwnersOwners want profitable operations that will pay them a return on their investment, plus operations managed for long life. Many owners are also concerned with employee's well being and their company's public image.EmployeesJob security and a good income are probably still the most important demands, however, as time goes by, employees are also demanding more involvement in safety issues, working conditions, and even how work is done.The PublicThe public requires acceptable environmental standards, as well as enjoying the prosperity supplied by a successful operation.How are Mines Managed?Most mines are managed very traditionally. The basic credo is that the managers make the decisions, and the hourly, and junior salaried employees do what they are told. Clearly this is the extreme case, epitomized by the long service shift boss who might say ""It took twenty-years to become a shift boss, and no miner is going to tell me what to do"" .There are some exceptions, two notable ones being Campbell-Chibougamau, and T.G.S. (now Kidd Creek Mines) which, in very different circumstances, decided on a more participative style.Campbell-Chibougamau, having closed down due to unprofitable operations, reopened, using a team structure with working leaders, and a system for sharing gains against cost targets with employees. Although the system has some problems, and development miners are bonused conventionally, this has been a basically successful program.Texasgulf Sulphur, a company with a history of non-union operations, and a participative management style, made a corporate decision to operate their Kidd Creek Mine in the same way. The orebody was rich enough to allow them the luxury to do this, but they have never had a strike, so perhaps they have more than saved the cost of the benefits and salaries they needed to pay. They also reward employees with a stock distribution scheme based on service and earnings."

Jan 1, 1985

By Larry A. Morris

The environmental impacts of industrial activities have become very serious concerns of the public over the past few decades. Not surprisingly, governments have responded with legislation and regulations to force industry to operate in a more environmentally responsible manner and, more recently, have prompted industry to initiate voluntary measures in response to specific environmental issues. The concept of Product Stewardship has evolved as a system or vehicle for the industrial sector to demonstrate an active concern about the environmental impact of their products, services and processes.

Jan 1, 1996

By Larry A. Morris

The environmental impacts of industrial activities have become very serious concerns of the public over the past few decades. Not surprisingly, governments have responded with legislation and regulations to force industry to operate in a more environmentally responsible manner and, more recently, have prompted industry to initiate voluntary measures in response to specific environmental issues. The concept of Product Stewardship has evolved as a system or vehicle for the industrial sector to demonstrate an active concern about the environmental impact of their products, services and processes.

Jan 1, 1996

By K. Miao, W. Mu, M. Sharma, A. Haas, N. Dogan

"The ever increasing demand for cleaner steels with low inclusion content has highlighted the limits of our current knowledge for controlling and predicting inclusion agglomeration and removal during liquid steel processing. Key knowledge gaps in this area result from the complex nature of the problems associated with measuring and visualizing the phenomena studied. Confocal scanning laser microscope (CSLM) allows for continuous in situ observation of micron-size samples in real time, at high resolution, under conditions relevant to the steelmaking process. This paper summarizes some of recent CSLM applications in our laboratory to illustrate the methods of analyzing transient behavior. The reaction between inclusions and slag is given as an example. The dissolution rate of calcium aluminate inclusions in CaO-SiO2-Al2O3 slags has been studied at elevated temperatures: 1500, 1550 and 1600°C as well as thermodynamic/kinetic analysis. It is found that total dissolution time decreased with increasing temperature. The rate limiting steps are discussed. It is shown that the diffusion through a product layer is responsible for dissolution at 1500°C. At higher temperature, dissolution is most likely controlled by both boundary layer diffusion and chemical reaction at the slag-inclusion interface. In this paper, the evidence for and against the theory will be critically examined and repercussions of the theory to steel refining processes will be discussed.INTRODUCTION Inclusion formation during liquid steel refining is an unavoidable consequence of current ladle steelmaking processes. The nature and quantity of the inclusions formed in steel is critical in steelmaking, as it affects both productivity through clogging, and downstream physical properties of the steel. It is therefore crucial to better understand and control the formation, agglomeration and dissolution behaviour of inclusions in a slag in order to improve the removability of inclusions from liquid steel. Most research (Sandhage & Yurek, 1988; Sandhage & Yurek, 1990a; Sandhuge & Yurek, 1990b; Sandhuge, 1991) relevant to the kinetics of inclusion removal has been obtained by using a technique where simulated inclusion material (ceramic rods) is dipped in slag and the dissolution rate is measured. While much has been learned using this approach, the difference in scale from bulk materials to inclusions is likely to have a significant bearing on the dissolution kinetics of inclusions in a slag and will certainly result in a very different influence of capillary effects. Further, the data obtained using an indirect (dip test) procedure relies on a comparison of the initial and final conditions of a sample rather than in-situ observation which can be achieved in a confocal microscope in real time."

Jan 1, 2017

By B. Yu, Y. O. Oyediran, M. Robart

"This paper presents the latest flotation development testwork conducted in 2015 on the ‘B Zone’ samples from the Strange Lake Alkalic Complex (SLAC). Since the discovery by Iron Ore Company of Canada (IOC), metallurgical development has been under taken by a number of mining companies targeting various value metals, including yttrium, zirconium, niobium, and rare earths.Most recent, Quest Rare Minerals Ltd. (Quest) completed a Pre-Feasibility Study (PFS) in 2013 where the flowsheet was relatively complex and led Quest to explore alternative options. In 2014, the PFS flowsheet was simplified and one of the features introduced was pre-concentration by rougher flotation. The combined rougher flotation concentrate and slimes successfully recovered >90% TREE in 60% mass thus reducing capital cost and technical risks of the downstream hydrometallurgical processes. The latest flotation development testwork focused on achieving a pre-concentrate in which >80% TREE are recovered in 20% mass. Two separate reagent schemes, based on an ester phosphate collector (Clariant 1682) and a benzoylhydroxamic acid collector (Florrea 7510), were developed. Parameters evaluated in the development testwork included desliming, secondary yttrium and zircon collectors, depressants, temperature, conditioning temperature, time, and density, pH, sodium silicate type, cleaning, and flowsheet configuration. Both developed reagent schemes achieved the targeted metallurgy.INTRODUCTIONThe Strange Lake Alkalic Complex (SLAC) was discovered after geological survey and mapping studies by Geological Survey of Canada and Newfoundland and Labrador Department of Natural Resources between 1967 and 1980. Subsequent exploratory drilling programs by Iron Ore Company (IOC) in the 1980s found that the REE and high field strength element (HFSE) mineralization were within the central region of the SLAC which was named A Zone by IOC and later renamed Main Zone by Quest Rare Minerals Ltd. (Quest). Additional exploratory drilling outside the Main Zone by IOC and later by Quest, led to the discovery of B Zone, which was recognized as the most significant deposit of rare earth elements, yttrium, and zirconium in the SLAC. The B Zone Indicated Resources are estimated at 278.13 Mt at 0.93% total rare earth oxide (TREO) and Inferred Mineral Resources are estimated at 214.35 Mt at 0.85% TREO (Oyediran et al., 2014)."

Jan 1, 2016

By K. Galovich, P. Krivokuca

"Quinsam coal mine is located about 25 km west of Campbell River on the east coast of Vancouver Island, British Columbia. Using continuous miners in a fully mechanized retreat room-and-pillar operation, it produces low sulphur, “super compliance” thermal coal for domestic and international markets at a rate of about 2600 t/d. Currently, 65 people work at the site, including some corporate employees.Opened in 1993, the Quinsam mine had a dismal safety record until 1997. Lost time injuries and medical aids were unacceptably high. In 1998, a change in corporate structure brought a change in safety attitudes; a total and unequivocal commitment to safety as job No.1 by corporate and site management. This commitment was clearly spelled out in a new mission statement, circulated to all employees by the new President and CEO, David Slater: “Safety is job No. 1; Production flows from safety; and Think safety at all times.” As well as re-defining workplace safety practices, QCC tightened engineering controls and enforced strict adherence to mine plans.This paper provides a general background to the mining operation, and describes the safety practices that have resulted in an enviable safety record in recent years, reflected by provincial and national recognition."

Jan 1, 2004

By A. J. Oliver, C. E. O’Neil, I. J. Itzkovitch, V. A. Ettel

A new solvent extraction process for the separation of cobalt, copper and zinc from nickel sulphate process streams has been developed. It involves selective extraction of these elements with a quaternary ammonium thiocyanate dissolved in an aromatic diluent. The chemical principles of this process have been investigated and are described, together with background physico-chemical data relating to the use of this solvent. Long-term testing in a continuous "mini-plant" circuit gave high-purity nickel and cobalt products (Ni/Co —200011 and Co/Ni ~1000/1 respectively).

Jan 1, 1976

By M. S. Badollet

Introduction The manufacture of some asbestos products involves the use of asbestos in combination with water, cement and granular fillers. This type of production is often called the wet or semi-wet process and requires the use of either pressure or vacuum to eliminate the excess water in the fibrous blend so that the product may develop the proper strength during the curing stage. Asbestos - cement products available today are numerous and are a valuable contribution to the building industry. Their production in quantity depends upon the type of equipment employed, the speed at which it can be operated, and the factors involving the? blending of asbestos, cement, water, and fillers. Assuming that all mechanical troubles at a plant have been eliminated or are under control it is still advisable to study the basic properties of the raw materials used in the asbestos-cement products. The type of cement used is an important factor, but usually the manufacturer of the cement is willing to work with the asbestos development engineer and recommend the proper type to be used for the product. The source of the water should not be overlooked as a general factor involved in the production cycle. Waters containing a high percentage of contamination such as silts, humus, or soluble salts may adversely affect the setting of the cement or cause a slowing down of the production rate in the factory. Asbestos in combination with cement is an ideal material fo1 building products. It is inorganic, will not deteriorate, and can be handled by mechanical equipment with a minimum reduction of fibre length. The many physical properties peculiar to asbestos fibres should be well understood by the manufacturer. They may be briefly enumerated as follows: fibre strength, fibre composition, sliminess, length, harshness, softness, and filterability or porosity. This last named property is important and it is the purpose of this paper to present some basic studies on filtration as applied to production problems.

Jan 1, 1949

By Jean-Pierre Côté, Alexandre Noiseux

"Hatch and ArcelorMittal Mines Canada have combined their expertise to develop a dynamic model of the latter’s Iron Ore Pellet Plant in Quebec, Canada. This model was used to predict the benefits of different expansion projects, as well as asses the best implementation sequence.Two modelling tools were used: a discrete-event simulation software used to develop the dynamic model of the Pellet Plant and an in-house process simulator. The latter was based on operational data and known behavior of the process, and was calibrated with historical data gathered under different operating conditions.The results of the process simulator were used as input values for the dynamic model, which included all of the operation steps of the pelletizing process, from concentrate beneficiation to baking of the pellets. The model has been validated by assessing its capacity to represent adequately the operation of the plant during a 20-month operating period. It was able to reproduce the plant capacity within a precision of 1.2%.Simulated “what-if” scenarios allowed quantifying the production increase associated with the addition of new equipment such as ball mills or balling discs, implemented individually or in combination. Results revealed a potential 10% increase in the annual plant production by adding additional equipment in the two most limiting sectors of the plant, grinding and agglomeration. The simulation results made it possible to quantify the synergistic effect of two projects on plant throughput; the model showed that the combination of two projects resulted in a greater production increase than the sum of the same projects evaluated individually.Now that it has proven reliable, the simulation tool can readily be used by ArcelorMittal Mines Canada process engineers to perform simulations for equipment optimization, and to evaluate the impact of various operating parameters such as equipment availability and tonnage, product mix or concentrate quality. This work showed that a reliable model can be developed based on known parameters in combination with the proper integration of the process knowledge."

Jan 1, 2010