Search Documents

By G. Lucas

"Material substitution occurs continuously in response to competitive and economic pressures. Technical development can accelerate or slow substitution by improving the performance of the invading or defending material. The choices are seldom simple and have to be made in the context of continuous commercial change.The development and commercialization of a new aluminum material is examined. The material has been introduced into· several different markets, so it is possible to compare and contrast the degree of success obtained in each.IntroductionAluminum-based materials have been in use for over one hundred years and , therefore, the development of a new family of alloys is rare. In the early 1970s, Dr. L.R. Morris and his coworkers at Alcan' s Kingston Research Centre started work on what was, at the time, something of a scientific curiosity-a family of alloys strengthened by an unusual mechanism.This paper deals with the development and commercialization of what became known as the Alcan 255 alloys"". These alloys have found uses in several markets, usually as improved substitutes for existing materials. Forecasting the usefulness of a substitute material in an existing marketplace is difficult, in part, because even material users are seldom able to specify precisely their requirements. This uncertainty can cause the failure of some substitutions but can also lead to opportunities which were not initially obvious.Technical BackgroundPure aluminum is a soft, weak material. It can be strengthened by the addition of various alloying elements and by work hardening. Alloying elements usually act by forming solid solutions which are stronger than the pure metal or by precipitating during heat treating or aging and so preventing the easy movement of dislocations during deformation. Elements which can perform either role had been investigated for decades and were thought to offer little chance of technical breakthrough in 1970. An outgrowth of the then new and exciting research on directional solidification seemed, however, to offer such promise.Some aluminum-iran-manganese alloys will solidify under certain conditions as 'coupled growth' eutectics (Figs. I and 2). The microstructure shows one phase growing as long rods through the other. This is an uncommon structure and it was investigated to see if it had equally unusual properties. On deformation by rolling the rods were broken up into small equiaxed , evenly-spaced particles (Fig. 3). Materials with this structure were found to be stronger than other alloys with similar amounts of alloying addition, and to resist thermal softening remarkably well. This combination of properties was thought initially to be due directly to the particles by a dispersion strengthening mechanism, but later this was found not to be strictly true."

Jan 1, 1987

By D. Bouchard, M. Forté, A. Charette

A transparent replica of a casting die was built to achieve a better understanding of the filling mechanisms of aluminum in high pressure die casting. Water and tomato paste were respectively used as analogues for the Newtonian liquid aluminum and the non-Newtonian semi-solid aluminum. The transparent die was installed on an industrial casting press and filling was filmed with a high-speed camera. Differences between the Newtonian and non-Newtonian fluids are presented and discussed.

Jan 1, 2006

By D. Haraguchi, S. Izawa, C. Tokoro, S. Owada

"Arsenic is widely known as a toxic element for humans, animals and plants. Because of more stringent wastewater standards not only in Japan but also around the world, research for appropriate and efficient treatment method for arsenic is becoming increasingly important. Coprecipitation or adsorption process using ferrihydrite is widely implemented for dilute As(V) removal from wastewater. In this study, the sorption mechanism of dilute As(V) with ferrihydrite in coprecipitation or adsorption process was investigated. To accomplish this, we conducted batch experiments of coprecipitation or adsorption and compared these results for sorption isotherm and zeta potential. These experimental results showed that sorption mechanism in coprecipitation process depends on the initial As/Fe molar ratio; simple twodimensional adsorption onto the surface of ferrihydrite when the initial As/Fe molar ratio was < 0.4, and some three-dimensional uptake with ferrihydrite when it was = 0.4. We also evaluated the sorption mechanim by analysis of X-ray diffraction (XRD) and X-ray Absorption Fine Structure (XAFS). XRD or XAFS spectra showed that surface precipitation of amorphous ferric arsenate was formed when the initial as/Fe molar ratio was = 0.4, beyond the thermodynamic bulk precipitation range for ferric arsenate.INTRODUCTIONArsenic is toxic to animals, including humans, and long-term exposure to arsenic via drinkingwater causes cancer of the skin, lungs, urinary bladder, and kidneys, as well as other effects on the skin such as changes in pigmentation and thickening (Ghosha et al., 2008). Elevated levels of arsenic are often present in the environment as a result of the weathering and dissolution of minerals as well as in response to numerous anthropogenic sources including the discharge of mine wastes, coal fly ash and the use of pesticides that contain arsenic (Nriagu, 1994; Singh et al., 2007). Indeed, the potential for arsenic exposure affects many people, as evidenced by several million people in Bangladesh and India being at risk of exposure via drinking water obtained from contaminated groundwater sources (Ahmed, 2001).Acid mine drainage (AMD) containing arsenic is a global environmental problem (Dold, 2008; Liang and Thomson, 2008) that also affects Japan, which has many abandoned or closed mines that have been generating AMD for the last few decades (Masuda et al., 2008). Several such facilities in Japan produce AMD containing dilute concentrations of arsenic that exceed Japanese effluent standards (0.1 mg/dm3) (METI, 2006). For example, AMD from the abandoned Horobetsu sulfur mine, the largest AMD source in Japan, contains approximately 10 mg/dm3 arsenic."

Jan 1, 2012

By Silvana Costa

In the last two decades, there have been nearly no new mining towns built in Canada. Governments and mining companies have viewed long distance commuting (LDC), commonly known as fly-in-flyout or fly-in mines, as a way to avoid problems associated with building a new community and providing for its sustainability after mine closure. LDC is also considered more cost-effective than building a mine town. The intensification of the use of LDC in the Canadian mining sector has been quite rapid, particularly in northern regions. However, LDC has implications to employees, their families and communities, which deserve further examination, particularly considering the significant expansion in Northern mining and Aboriginal participation in this sector. This paper presents a review of the major issues in long distance commuting, both from an industry and community perspectives. It is a result of preliminary investigation for a PhD research project that will be pursued by a Bridge Fellow and UBC Mining Sustainability Working Group member, and guided by an interdisciplinary research team at the University of British Columbia (UBC). The Bridge Fellowship Program is research-training program linking the UBC?s Faculties of Medicine, Engineering and Graduate Studies. Its mission is to develop creative evidence-based prevention measures for public, environmental and occupational health problems. The SWG is an interdisciplinary student group based in the UBC Department of Mining Engineering, committed to respond to the complex sustainability-related challenges currently faced by the mining industry. In other to pursue this project, it is paramount that industry and local communities alike participate in the development and clarification of research questions as well as in the research design. It is hoped that this paper will function as an invitation for industrial and community partners for such study. The main themes identified for this research are occupational health and safety of LDC employees, family life impacts and community health impacts of this model of resource development.

May 1, 2004

By Madaah Hosseini H. R., P. Abachi, S. Miraghaei

In this study, the effects of milling time, chemical composition and heat treatment on microstructure and magnetic properties of nanocrystalline Fe-Si (6.5-25 at.% Si) alloys prepared by mechanical alloying have been investigated. The results show that increasing the milling time or the Si content, decreases the lattice parameter and increases the internal microstrain. The prepared powders mainly consist of micron-sized particles with an average grain size of less than 20 nm. The specific saturation magnetization values are slightly less than those of single crystal or conventional Fe-Si alloys and decrease as Si content increases. The coercive force values of the nanocrystalline as-milled powders are much higher than those of corresponding Fe-Si bulk alloys with a minimum at 13.5 at.% Si. The values of coercive force decreased after annealing but it seams that the residual strain developed during milling is not the major contributing factor to the higher values of coercive force in the mechanically alloyed powders and nanocrystals behave as single-domain particles without exchange interaction between them.

Jan 1, 2006

By S. Kashani-Nejad

The kinetics of the thermal decomposition of samples of Mg2(OH)3Cl.2H2O that were obtained by a novel leaching technique applied to a commercial magnesium electrolysis feed were investigated under ambient atmosphere. Thermogravimetric (TG) Analysis showed that decomposition of Mg2(OH)3Cl.2H2O exhibited a single intermediate stage wherein crystalline water was lost at roughly 108 °C. Conversion of the resulting Mg2(OH)3Cl to MgO, HCl and 1120 occurred at temperatures above 398 °C. Thermal decomposition of anhydrous Mg2(OH)3Cl was seen to be consist of two stages. Both stages exhibit first order kinetics with respect to the weight percent of Mg2(OH)3Cl remaining in the sample. However, the rates of decomposition in the two stages were significantly different. Detailed analysis of the kinetic data suggested that the rate of decomposition of Mg2(OH)3C1 was controlled by the rate of removal of the gases released. The change in decomposition rate during the course of the experiments was explained by HCI being released in stage 1 and followed by release of H2O in stage 2.

Jan 1, 2004

By A. G. Mattes

This paper presents an overview of passive, engineered, biologically-based anaerobic bioreactor (ABR) treatment systems of the sort that can be used to remove dissolved copper from mine wastewaters. The paper begins with a brief history of the origins of this treatment technology and continues with a discussion of principles of engineered wetlands (EWs, advanced kinds of constructed wetlands, CWs) and the use of vertical sub-surface flow (VSSF) varieties that contain pulp & paper biosolids as the reactive medium for EW cells. A brief outline of a procedural methodology used in evaluating the potential for biological treatment on a site-specific basis is also included. An introduction to the microbiology of passive biologically-based treatment systems is followed by some recent research results in the general area of wetlands and ABR research. The paper concludes with a brief discussion of several sites known by the authors to have successfully (or not) demonstrated the potential of this treatment option.

Jan 1, 2007

By W. G. Stevenson

With the author's background of extensive experience, this paper delineates the role of the prospector in modern-day exploration programs. The stages in the development of a prospect to a producing mineral district are outlined, and examples are given from the Ross River area of the Yukon Territory and the Peachland and Highland Valley areas of British Columbia.

Jan 1, 1970

By Raj K. Rajamani, Sanjeeva Latchireddi, Dave Plummer, Stieger. Julius

"The Cortez SAG mill liner design was recently modified to improve the mill operating energy efficiency. In addition to the expected benefits, the design change unexpectedly played a significant role of verifying the proposed grinding circuit expansion for the Cortez Hills project as well as illustrating current SAG mill bottlenecks. This paper will discuss the evaluation that addressed operator and maintenance observations, historical PLC data, and “crash stop” observations to calculate charge motion, packing between lifters, and slurry transport through grate and pulp lifters. The performance of the new shell and discharge end liner design will also be discussed as well as their role in the possible grinding circuit expansion.INTRODUCTIONCortez Gold Mines commenced operation in 1969 with its Mill #1 rated at a nominal 2,000 tons per day. Mill #1 was a conventional rod mill/ball mill circuit followed by an 8-stage CIP circuit. In the early 1990s the Pipeline deposit was discovered and subsequently Mill #2 was built to process the increased ore volume. Mill #2, commissioned by mid-1997, was a nominal 10,000 tons per day SABC circuit followed by an 8-stage CIL circuit for oxide gold ore. Operating and commissioning details of this plant have been published elsewhere (Powell, 1998). By late 1998, there was not enough ore volume to support both mills so the smaller, higher operating cost Mill #1 was put under its current care-and-maintenance status. A simplified flowsheet of the current mill is shown in Figure 1."

Jan 1, 2007

By F. Musuka, D. Jenkins, A. Keyes

BHP Olympic Dam operates a Direct-to-Blister copper flash smelting Furnace (DBF) and an Electric Slag Cleaning Furnace (ESCF). Tapping blister copper from these furnaces via tapholes is a routine task carried out by trained personnel. Blister tapping is a high-risk activity with personnel operating in close proximity to molten metal. BHP’s risk management framework has identified taphole integrity as key to managing the potential for loss of molten metal containment and molten metal – water steam explosion, both of which have the potential to cause multiple fatalities. As part of the focus on managing this risk, since 2017, a dedicated Taphole Development Team has been embedded in the operation to run an accelerated improvement program focused on safely and sustainably embedding an improved taphole design with greater integrity. The program of works includes selecting and testing of new materials as well as improving operating discipline by collaborating with tapping personnel to convert their knowledge into codified condition monitoring and operating strategies. Computational fluid dynamics (CFD) is being used to derive critical risk controls, and to develop live-alerts to infer excessive refractory insert wear. To date, improving DBF blister taphole mudgun clay has led to more consistent drilling depths and subsequently reduced oxygen lancing requirements, resulting in improvements in taphole insert service life. On the ESCF, insert performance testing and development of a new taphole condition monitoring strategy, is being used to increase taphole insert tonnages to more sustainable levels. Operations personnel have been closely involved in different phases of the change management, this has led to standardization of tapping practices for both furnaces, and improved ownership of the proposed changes. The paper discusses the maturity in taphole integrity risk management as a result of recent and ongoing developments. It then provides an overview of future taphole developments proposed at Olympic Dam. INTRODUCTION Tapping operations at Olympic Dam and learning from significant events The Direct-to-Blister furnace (DBF) at Olympic Dam was built with a conventional design blister taphole, which was designed for manual oxygen lancing and clay stopper bar plugging tapping operations (Campbell, 2005). Manual tapping is a high-risk activity, where personnel work in close proximity to molten metal, and molten metal personal protective clothing and equipment must be used. Opening tapholes by oxygen lancing is a skilled activity and unintentional damage to the taphole inserts can occur. Since 2008, a Mudgun and Drill unit has been developed and trialled and is now in use on the DBF blister tapholes, to remove personnel from the line of fire when opening and closing tapholes. This has the additional benefit of reducing lancing damage to taphole inserts. A new taphole design labelled the Modular Blister Taphole (MBTH) was developed at Olympic Dam for the Mudgun and Drill operation. The intent of the design was for mudgun clay to fill the entire tapping channel when plugging after a tap. The drill would then drill through this clay plug to open the taphole.

Jan 1, 2019

By J. S. Stachulak, K. A. Mackinnon

This paper deals with specifying and evaluating fans for mine ventilation projects. Topics such as fan and equipment design life, operating points, and operating conditions are discussed. Common operating problems, such as vibration, parallel operation, mechanical failure, erosion, corrosion, and deficient fan performance are covered. Apart from identifying the potential operating problems, likely causes and suggested remedies are given. Fan type, fan accessories, and likely system effects and fan testing are discussed. Suggestions on what should be covered when evaluating different fan options and proposals and suggestions on the verification of supplier claims and guarantees, including cost of operation, the evaluation of initial capital cost, estimate on maintenance costs, and likely replacement expenditure over the life of the fans. In addition, fan reliability, operational flexibility, suggested construction details and fan vendor past history and experience are reviewed.

Jan 1, 2004

By C. Dodds, R. S. Ferrari-John, The University of Nottingham, G. Dimitrakis, J. Katrib, A. R. Batchelor

"Sorting technologies have the potential to reduce energy use in comminution by rejecting uneconomic ore before feed material enters the mill. However, a major challenge for sorting porphyry copper ores is providing a basis of discrimination between valuable and non-valuable fragments, due to their complex mineralogies and textural features. Microwave heating in combination with infra-red detection (MW-IR) has been shown to provide upgraded feedstock for certain ores at bench scale. Selective heating of copper sulphide minerals compared to the gangue leads to an increased thermal response for valuable fragments, providing the basis for sorting.Rapid scale up of MW-IR from bench scale to a 100 t/h continuous pilot plant facility has been facilitated by the design of microwave choking structures to allow continuous operation at industrially meaningful throughputs, whilst meeting health and safety and electromagnetic compliance standards, and the integration of materials handling with electromagnetic systems.Laboratory batch testing on a pilot scale microwave system has been undertaken to investigate the thermal response of copper ores under industrial conditions, at microwave energy inputs up to 1 kWh/t. These results provided the operating window and recommended test conditions for the continuous pilot plant. Sortability curves predicted in the laboratory are in good agreement with separations achieved during continuous pilot plant operations. The potential microwave sortability of a number of ores has been studied, allowing informed decisions to be made about potential ore candidates based on mineralogy. Future development of the technology will be underpinned by the creation and validation of scale up concepts for 1000 t/h operations. Understanding the value proposition for individual sites/applications will be central to unlocking the potential economic and environmental benefits of microwave sorting."

Jan 1, 2016

By S. Bozorgi, K. Anders

"The automotive applications of heat treatable AlCu cast alloys are designed for performance at high temperature, which can be improved using specially alloying element as well as different heat treatment. In this research work an effect of alloying element such as Cu, Ni and heat treatment on microstructures and mechanical properties of AlCu alloy were investigated using optical microscope (LIMI), scanning electronic microscope (SEM) equipped with energy dispersive X-ray detection (EDS), Differential scanning calorimetry (DSC) and mechanical testing. It was found that during solidification most of the elements Cu, Mg and Ni segregated at the grain boundaries in the form of Al2CuMg or Al7Cu4Ni and a very small part of Cu and Ni element dissolved in the FCC-Al matrix. The latter is not completely reclaimable for strengthening mechanisms in FCC-Al matrix in its as-cast state. The results of mechanical test show that yield strength and ultimate tensile strength increases after heat treatment significantly compared with the as-cast state. Furthermore the mechanical properties at elevates temperature (240°C) is higher with higher Cu+Ni+Si containing alloys compared with the less Cu+Ni+Si containing alloy.INTRODUCTION Due to the high strength-to-weight ratio, high strength and ductility at room- and elevated temperature, AlCuSi cast alloys are widely applied in the automotive industries specially for producing cylinder head and engine block, where modified alloys with enhanced metallurgical properties are always needed to satisfy the ever increasing demands for the applications. The AlCu based cast alloys can be strengthened by age hardening. The precipitation processes from which this hardening is derived can be attributed to the presence of selected trace element additions or micro alloying, which can change the process or kinetics of precipitation in age hardenable AlCu cast alloys (Polmear, 1998; Morris, 1991). Furthermore their strength is mainly controlled by the aging process through the precipitation and growth of very fine precipitates of the ?'-phase (a semi-coherent, metastable form of the equilibrium Al2Cu phase) from the Al and Cu Guinier-Preston (GP) zones. Several studies have shown that solute clustering occurs prior to the precipitation of GP zones, and this modifies both the nature and kinetics of the precipitation process. The typical size of GP zones is in the order of tens of nanometers, and the chemical composition of these precipitates is not easily measured, even with a typically analytical electron microscope (Polmear, 1989)."

Jan 1, 2018

By Jian-bin Xie, Lin-fang Shen, Zhi-liang Wang

"In order to research temperature field for construction of connecting passage in Metro using artificial freezing method, the finite difference software FLAC3D is employed to numerically simulate construction process of connecting passage. During construction, the overall distribution of temperature field around connecting passage, the relationship between soil temperature and freezing time, the distribution and variation for the thickness of freezing wall are studied from the perspective of numerical analysis. The results show as follows: after 55 days’ freezing, the soil temperature surrounding connecting passage is about -24 oC ~ -28 oC, and the minimum thickness of freezing wall is about 4.0m, which is larger than the design value 3.1m. So construction conditions have satisfied to the excavation of connecting passage and pumping station. During the excavation of connecting passage, soil temperature has almost no obvious change and the thickness of freezing wall remains constant mainly. After 45 days’ normal thawing, the temperature of freezing wall rises 12 oC approximately. And the soil temperature rises faster at the beginning of the normal thawing stage. In the whole process of construction, the frozen area is about 5m outside the edge of connecting passage, and the cooling area is about 10m outside the edge of connecting passage. INTRODUCTIONThe first recorded application of the artificial freezing method is on a mineshaft project in 1862, and it has been widely used in foundation pit engineering, subway tunnels, mine shaft engineering and so on (Wang Zhiliang, 2010; Zhang Juanxia, 2012; Qiu Fan, 2007; Zhou Xiaomin, 1999). This method has many advantages of enhancing soil strength; decreasing permeability and adopting various unstable soils (silt clay, sand, gravel, etc.). It has been applied successfully in metro engineering construction in Beijing, Shanghai and Nanjing. According to incomplete statistics, the construction of connecting passage using artificial freezing method accounted for 98% in Shanghai metro (Qiu Fan, 2007)."

Jan 1, 2015

By Norman Orr, J. W. Gregg, Jack Wahl

The Pembina Cardium pool is a low permeability, stratified, solution-gas drive reservoir. Water-flooding has proven to be an effective means of pressure maintenance for all areas of the pool in which an economic rate of water injection can be maintained. The majority of water injection wells in the pool are converted oil well~ with capacities greater than 100 millidarcy-feet. If the average injection rate per unit of capacity can be in-creased the lower capacity areas of the pool can be economically flooded. Theory, laboratory work, and two . early miscible-flooding projects with-in the pool suggested that average water injection rates for converted wells could be increased two to three-fold by the initial injection of natural gas liquids and natural gas. How-ever, these two early projects received volumes of natural gas liquid!:' and high-pressure natural gas which would be economically prohibitive for routine stimulation. Area D, one of the Five-

Jan 1, 1962

By R. Alarcón Sch., R. Abel F.

For many years, copper cathode quality has been a priority for end consumers, since it affects the variety of products that can be obtained from them. From the beginning, physical and chemical quality of the wire bars was controlled, as this product was used to obtain wire rod and other forms of copper by wire drawing. At that time, all the electro refined cathodes were melted and casted as wire bars. Subsequently, in the 80’s, with the introduction of continuous casting furnaces, it was possible to directly produce wire rod from cathodes. From then on, cathodes quality standards were consistently increased, by the introduction of uniform criteria, among which we can identify ASTM and British Standards as well. Also, producers began to use more demanding internal standards than the existing specifications, in order to differentiate their cathodes as high quality products among customers. Today the physical aspect of cathodes, including nodules, cracks, sulfates, or others, is the first element used by end customers to assess their quality. This paper aims to show a brief vision of the evolution of quality specifications for products used to manufacture copper wire. INTRODUCTION From the beginning of refined copper production for industrial purposes, mandatory minimum quality conditions were established. These quality conditions were used as the main element to determine prices and discounts of the respective sales contracts. Reviewing the copper development history, we can appreciate that its quality requirements had been constantly evolved, so that currently refined copper has an extremely high quality standard, that allows its direct use in the production of ultra-thin cables and other products applied in the industry. In each stage, refined copper production has fostered the development of technology used in their treatment. Similarly, cathode processing technology has been evolving to minimize treatment costs in order to generate a wire rod for several uses, ranging from power cables to super conductors. In this sense, to the already known type of fusion processes of the Southwire or Asarco type (capacities over 80 kt / year), wire rod production processes of the Upcast or Rautomead type (capacities between 20-50k t / year) have been added. They immediately deliver oxygen-free wire rods. In both cases, we can conclude that the clients' requirement had evolved from a chemical criteria focus, to considering more subjective aspects, such as visual control as the first stage of inspection.

Jan 1, 2019

By V. Prasad, A. Afacan, K. Popli, S. Dubljevic

Froth flotation is one of the most common and widely used separation processes in the mineral processing industry; however, its complexity means that complete understanding of the process has not yet been achieved. A dynamic fundamental model is needed to enhance the understanding of the process and to improve process control. It is challenging to capture all the phenomena involved; hence, we propose a multiscale modeling approach with a framework ranging from macroscopic (equipment scale) to microscopic (attachment, detachment) models along with distribution models for ore particle sizes. Real-time froth properties are obtained using a vision-based sensing system. These measurements can be used for developing a soft sensor for grade using statistical methods such as PCR (principal component regression) and PLS (partial least squares) regression. The fundamental model is updated in real-time using extended Kalman filtering. Attachment dynamics are studied for different particle size distributions. The modeling and soft sensing is tested on batch flotation cell for the pure mineral galena with different particle size distributions using Xanthate and MIBC as collector and frother, respectively. The model, online measurements and soft sensor are useful in developing monitoring methods for froth flotation.

Jan 1, 2015

By Q. Zhang

The necessary capability of the gravity transportation pipeline system for cemented coal gangue backfilling at the Suncun Coal Mine, China, is about 74.4 m3?h-1 according to mining production and working times in the mine. It is estimated that the working velocity and maximum pipe length-backfill depth ratio of the backfill system are 3.82m?s-1 and 5.4, respectively and that the probable backfill capability of the system is 110.18m3?h-1. Results of hydraulic calculations for the backfill transportation system show that the designed backfill system is reliable in flowability and sufficient for backfill capability needs.

May 1, 2007

By G. Deschênes

The Eleonore property (James Bay district of Northern Québec), owned by Goldcorp, hosts gold within stockworks of quartz-tourmaline-arsenopyrite veins and veinlets contained within microcline (potassic alteration) and brown tourmaline replacement zones. The preliminary investigation to recover gold from drill core samples showed that flotation followed ultrafine grinding and cyanidation is the preferred option. Ultrafine grinding is used to liberate gold finely disseminated in sulphides. The flotation concentrate used in the investigation had a P80 of 11 microns and contained 75.5 g/t Au, 5.0 g/t Ag, 10.3% S, 0.07% Cu and traces of antimony (0.03%). The mineralogical characterization showed the presence of 65% gangue minerals, 23% pyrrhotite (hexagonal), 9.6% arsenopyrite, 2.2% pyrite and 0.08% chalcopyrite with trace amounts of galena (0.05%) and sphalerite (0.03%). Gold was in the form of native gold and electrum. A straight cyanidation conducted at pH 11.0, DO of 3-5 ppm, 2000 ppm NaCN, 20 C 72 hours extracted 97.0% Au and consumed 31.5 kg/t NaCN. The equilibrium was reached within 24 hours. Increasing the dissolved oxygen to 16 ppm reduced the consumption of cyanide to 22.0 kg/t with 96.7% Au extraction. A 16-h pretreatment with 2.0 kg/t lead nitrate, followed by a 24-h cyanidation reduced the cyanide consumption to 6.0 kg/t with a gold extraction of 97.5%. Increasing the lead nitrate addition to 6.0 kg/t reduced the cyanide consumption to 1.2 kg/t by passivating the surface of pyrrhotite. The gold extraction remained at 97.0%. It was possible to decrease the concentration of cyanide to 800 ppm NaCN without compromising gold extraction. The associated cyanide consumption was 1.2 kg/t NaCN. The passivation of gold grains was an issue when the cyanide concentration was decreased to 550 ppm NaCN. The gold extraction decreased to 92.2%. The average lime addition for all the tests was 7.4 kg/t and the average silver extraction was 80%. Efficient cyanidation of an ultrafine sulphide concentrate with only 800 ppm NaCN represents an advance in leaching of ultrafine sulphide concentrates.

Jan 1, 2013

By Y. Huang

Corrosion of GaAs in aqueous electrolytes is a major limitation in implementing GaAs-based photoelectrochemical solar energy conversion systems, In this work, the corrosion behavior was investigated by electrochemical methods and surface analysis approaches, in both H2SO4 and NH3?H2O solutions, Open-circuit measurements showed that the cleaned GaAs surface was very sensitive to water/air, Impedance measurements for n-GaAs showed that an inductive loop only appeared at a high corrosion rate because a reaction intermediate is the oxidant for a further decomposition step in combination with chemical reaction with water, The results suggest that the same corrosion/decomposition mechanism occurred on n-GaAs in the two solutions, When the surface-hole concentration was low, the hole injection or generation process was the rate-determining step, At large reverse bias on n-GaAs, with high-hole concentration, the corrosion rate was limited by a Faradaic adsorption process, involving an adsorbed intermediate, The different surface compositions after corrosion in the two solutions can be explained by the dissolution of As(0), Further oxidation of As(0) to As(III) in NH3?H2O solution is still slow, as suggested from X-ray photoelectron spectroscopy (XPS) analysis,

Jan 1, 2005