Search Documents

By C. Mills, A. O. Burt

"The paper examines the role of gravity concentration in both an historical context and within the modern mineral processing industry. It discusses the principles of the process on both a theoretical and practical level. The importance of more mineralogy and its effect on the choice of the wide range of equipment available is discussed. The paper concludes with a discussion on the relative merits of gravity concentration with other forms of processing.IntroductionIt is an unfortunate, albeit popular, misconception among otherwise enlightened engineers in the mineral processing industry that gravity concentration was a process developed in the dark ages, perfected in the middle ages, and abandoned in the modern ages.Gravity concentration was developed in the dark ages - long indeed before that. Agricolau: cited examples of gravity concentration, crude examples admittedly, being practiced over 3000 years ago. However, gravity concentration is not dead. Far from it. As recently as 1978 it was reported that the total mineral tonnage treated by this process in the United States was greater than that processed by flotation. Coal represents the bulk of the or e treated by gravity separation in the U.S.A., with iron ore representing a major portion of the balance."

Jan 1, 1985

By Ron Davidson

"The Utility Mine in southeast Saskatchewan is owned by Saskatchewan Power Corporation and operated by Mana/ta Coal Ltd. Up to 3.3 million tonnes of lignite is supplied annually to Saskatchewan Power's Boundary Dam Generating Station. The coal occurs in two predominant seams which are covered by up to 37 metres of saturated fine-grained overburden. Overburden is removed by two draglines working in two pits. Coal is hauled to the mine mouth power station. Comprehensive drainage and reclamation programs are integral parts of the operation. IntroductionThe Utility Mine is owned by Saskatchewan Power Corporation and operated by Manalta Coal Ltd. It is located in southeastern Saskatchewan, approximately 200 km southeast of Regina and 8.5 km southwest of Estevan (Fig. 1). The climate of the Estevan area is semi-arid with long, cool winters and short, hot summers. The mean annual precipitation is 42 cm and the mean summer temperature is 20°C; mean winter temperature is -10°C. The Utility Mine supplies coal to the adjacent Boundary Dam Generating Station. Increases in the station's generating capacity during the past decade have resulted in an extensive expansion program for the Utility Mine. This expansion program, the geological conditions present in the area, and the mining/reclamation operations will be highlighted in the following sections<1.2). History The Estevan area has a long history of coal mining. In the early years, coal was mined via entries into coal seam outcrops along the slopes of the Souris River valley. Surface strip mining was introduced in the late 1920s and progressed to the point where it totally replaced underground mining by the 1950s. Surface mining methods are currently used exclusively by all of the Estevan area operators."

Jan 1, 1985

By Egon Berger

"In recent years the trend in underground metal mining has been toward ever increasing blasts (often in excess of 100 000 tonnes per blast). The Canadian mining industry has been in the forefront of these developments (VRM, LBHand cable bolting to stabilize the surrounding rock /avoid dilution).In order to move these large tonnages, efficient loading systems have to be developed. This paper shows the technical and economic implications of various loading scenarios based on a predefined (however typical) stoping layout by:1 . discontinuous loading using scoop trams;2. discontinuous loading using scoop trams in combination with low profile dump trucks;3. continuous loading (based on loading performance/operating costs of the AL-60) in combination with low profile dumptrucks.The cost advantages of production concentration (loading large tonnages from one drawpoint}, made possible by continuous loading as opposed to sea tiered mining (small tonnages), using discontinuous loading in tunnelling will be presented, based on actual results obtained in a decline development project using the A L-60 continuous loader. At as pacing oj150m between turning bays, it was found that continuous loading was out performing discontinuous loading in approximately80% of the overall decline development.Fuel consumption and total cycle times are compared, and a cost assessment is presented.INTRODUCTIONThe subject of this paper deals with the introduction of continuous loading in underground metal mining and single heading tunnelingContinous mining has been widely introduced both in underground and surface coal mining. Mechanized longwall mining, utilizing moveable shield supports in combination with double drum- shearers, has resulted in a tremendous increase of coal production per working face.This has led to very concentrated mining operations. In a typical German coal mine two mechanized longwalls nowadays would produce the same amount of coal as 12 to 15 longwalls in the 1950s. One longwall in a South African coal mine has recently set a world record with 120 000 tonnes of coal in a single month.In underground metal mines-often due to the irregular nature of the ore body and the mining methods used-mining is far less concent rated. Ore is often produced from a large number of stopes and production sections. Sometimes, a substantial amount of ore may be obtained from development in the orebody (40070 at a German base metal mine)."

Jan 1, 1989

By Arnold R. Miller

Overview ? Vehicle Projects LLC (prime contractor) and the Fuelcell Propulsion Institute have developed the world?s first fuelcell locomotive. ? Principal applications are underground mining and tunneling. ? Because fuelcell vehicles solve the problem of underground emissions, mining is expected to be their first commercially viable market. ? The first year of a three-year project to develop a fuelcell mine loader is funded and underway.

May 1, 2002

By Colin P. Skidmore

Long touted as Australia?s fourth uranium mine the sediment-hosted Honeymoon Uranium Project is close to commercial production using insitu-leach mining methods. Uranium mineralisation occurs as pitchblende coatings on unconsolidated quartz sand and gravels within a stacked aquifer system in a buried palaeochannel located in the Curnamona Region of South Australia. A final NI43-101 Feasibility Study is close to completion which has included extensive delineation drilling using PFN technology to accurately measure uranium grade and distribution. This data integrated with a detailed 3D sedimentalogical model is being used to optimise wellfield and plant design.

May 1, 2006

Red Chris Project Project Status ? Tahltan, Iskut First Nations MOU ? Bankable Feasibility Study ? BC Environmental Assessment Certificate ? CEAA (Federal Environmental) ? EPCM contracts LOI?s ? US$110 million Project Debt Financing(credit approval pending) ? 1st5 years concentrate production sold ? 99,150 m of drilling in 371 holes First Nations Participation Agreement ?Advanced stage negotiations

May 1, 2006

By L. A. Melis, K. S. Fraser

"This paper describes the development of a milling circuit for the complex Midwest orebody, containing a high-arsenic uranium ore typical of that found in northern Saskatchewan. The results of preliminary bench-scale test work are summarized. Data from a pilot-plant program carried out at the Ontario Research Foundation are provided for the selected mill flowsheet. Also described are waste circuits which have been established to produce effluents of acceptable quality. Pilot-plant testing of sub-aerial tailings deposition is also described. The applicability of manufacturers&apos; equipment for the various circuits in the flowsheet is discussed.IntroductionThe Midwest uranium deposit is in northern Saskatchewan, 700 km north of Saskatoon, near the eastern edge of the Athabasca BasinDevelopment work on the project is directed by Canada Wide Mines Ltd., a subsidiary of Esso Resources Canada Limited. Participants in the project are Esso Resources Canada Limited, Numac Oil and Gas Ltd., Bow Valley Industries Ltd ., Mink Mining Corporation and Midwest Mining Corporation.The deposit consists of a series of flat lenses of massive ore overlain by a halo of lower-grade sandstone ore. The massive ore is formed of pitchblende and nickel arsenides, along with clay, and averages about 10% U and 9% Ni, The principal minerals are pitchblende (UO2-UO3), coffinite (U(SiO4)1-x(OH)4x), gersdorffite (NiAsS), niccolite (NiAs) and rammelsbergite (NiAs2). The sandstone ore, a friable clay-rich sandstone with sooty pitchblende, averages about 0.4% U and 0.6% Ni. Typical expected mill feed analyses are given in Table I.A bench-scale development program ore was carried out during the period from August 1978 to May 1981 in the laboratories of Lakefield Research of Canada Ltd. (Lakefield), (Lakefield, Ontario), the Colorado School of Mines Research Institute (CSMRI), (Golden, Colorado) and, to a lesser extent, the Ontario Research Foundation (ORF), (Mississauga, Ontario) and the Saskatchewan Research Council (SRC), (Saskatoon, Saskatchewan). Direction of the development studies was shared by Canada Wide Mines Ltd. and its metallurgical consultants, A.H. Ross and Associates. Input was received from Envirotech, Enviroclear, Interox America, and Knight and Piesold Ltd."

Jan 1, 1983

By Norman A. Jull

"Factors which affect the separation achieved in a hydrocyclone are discussed and illustrated with graphs of some mathematical relationships.Definitions of separation and sharpness include comment on use of elutriation devices.A plea is made for better evaluation of field data prior to their reporting or use in calculations. Methods of evaluation are suggested, with samples of the relevant calculations.An example of the effect of percent solids errors is given, with computer printout and plotted corrected recoveries.INTRODUCTIONThe range of interest in cyclones runs from a simple demand for classification results to a detailed study of published equations defining cyclone characteristics. Probably this group covers as broad a range and, in an attempt to offer something for everyone, I will begin with general operating comments, then move on to more analytical topics. Ideally, an author would compose his paper after the discussion period, when he would have a better idea of the areas of special interest to his audience.Sor'1e of you may share our incurable fascination with classification, especially as performed in cyclones. It is amazing that such a simple device could be in use for more than 20 years and retain as much mystery as it does. Substantial parts of the mystery have been solved but some remains, to keep up our curiosity. There is at least one valid reason: the unusual compactness of this device, which makes internal observation very difficult. What other unit can you think of which performs such a complex separation between particle sizes, shapes and specific gravities at such high capacity? Retention time in a cyclone is typically 3 seconds!Mutual Agreement - In a cyclone, every parameter of geometry and of operation interacts with every other. In an orderly discussion of individual parameters it would be necessary to repeat, in every section, 11 if all other factors are equal"". Could we agree now, for our mutual convenience, that that phrase is clearly understood between us during the remainder of this paper?"

Jan 1, 1972

By G. J. Reid, D. H. Stewart

"A diversity of structures and rock types in the Aft on pit has resulted in the occurrence of several different types of wall failure. Delivery of ore to the mill has not been affected and safety has not been compromised thanks to effective remedial 1V0rk and to a system of structural mapping, back analyses of failures, groundwater monitoring, and simple movement monitoring. Remedial measures have included artificial support, dewatering (including vacuum-assisted drainage), flattening of slopes and temporary buttressing. This paper describes six different wall failures at Afton and highlights the features of each. Examples given include rates of movement, extent and direction of movement, and piezometric responses. The practical, low-cost monitoring system was sufficient in one case to allow the prediction of date of failure. IntroductionThe Afton copper deposit is located 13 km west of Karnloops, British Columbia and has been mined for nine years out o f an expected eleven-year life. Open pit mining has reached 700 feet below sur face and is designed to proceed to 970 feet below surface by the time the pit is completed. The excavation is in a structurally and lithologically complex environment. Inevitably, some wall failures have occurred but these have been limited to small, manageable failures which have not compromised production or safety. To handle the failures it has been necessary to understand their nature. Of prim e concern has been the rate s of movement, but displacement vectors and hydrology have been monitored as well. The monitoring system is based on EDM surveys and on wire extensometers and plates set across cracks. Water levels have been read in standpipe piezometers. At Afton the emphasis has been on simple, practical, and inexpensive monitoring and because rock type s and structures play such a major role in any failure, detailed geologic al mapping is carried out."

Jan 1, 1988

By Alfredo Bambaren

First Encounters between Communities and Mining 1. Importance, meaning and process 2. Antamina?s study case 3. ?Self-organization? theory (NLP) 4. The story we tell, the values we live 1. Importance, Meaning and Process ? First encounter stays in mind as a model. ? First encounter means foundation. ? First encounter builds the story.

May 1, 2010

By C. A. Biley

"A dedicated iron removal stage was installed at Anglo American Platinum’s Rustenburg Base Metals Refiners (RBMR) during an expansion project which began execution in 2010. The Pressure Iron Removal (PIR) process aims to precipitate iron from a nickel leach solution under medium temperature (145 °C) oxidative conditions using caustic for neutralisation. Since commissioning, the process has been robust in removing iron from the refinery but has shown significant variability in the residues produced. These residues, which are typically comprised of ferrihydrite, hematite or natrojarosite, have varying iron contents and different physical properties which have implications for their filtration and ultimate removal from the refinery. Since over 95% of nickel plated at RBMR passes through the PIR section, volumetric constraints caused by poor filtration performance directly influence nickel production and stabilisation of this process remains central to the continued ramp-up of the refinery to full nameplate capacity. This paper details the development of the PIR process and the journey from concept to implementation. Recent laboratory and plant scale tests have highlighted the importance of the initial phase formed in the autoclave for the ultimate residue requiring filtration and how the feed acid concentration is a critical control parameter. On this basis, a new caustic dosing philosophy was implemented which improved pH control in the autoclave. Further optimisation of the PIR process is on-going.INTRODUCTIONIn 2010, an expansion of Rustenburg Base Metal Refiners (RBMR) to increase nickel production from 21 to 33 ktpa began execution. The management of iron was pivotal in the ultimate configuration in the new circuit and one of the primary differences from the original circuit was the addition of a dedicated iron removal stage: Pressure Iron Removal (PIR). A significant drive for this new unit operation was to facilitate the separation of iron from other leach residues. Not only did this result in a significant decrease in the amount of leach residue but, without the constraints associated with iron precipitation during leaching, has permitted more aggressive leaching conditions and, correspondingly, greater throughput and efficiencies.However, as with many commercial implementations of even mature technologies, the journey from development to implementation has presented challenges for the continued ramp-up of the refinery to full nameplate capacity. Specifically, since all nickel bearing leach solution must pass through the PIR section prior to the nickel purification and recovery circuit, throughput difficulties in the PIR section can directly impact supply of feed to the nickel tank house. Since commissioning, the PIR autoclave has effectively removed iron from the refinery, but has shown significant variation in the solids phases produced in the autoclave. This variation presents difficulties for the filtration of the discharge slurry and represents a key throughput limitation which periodically impacts production. Additionally, the increasing production rates associated with the ramp-up of the refinery have resulted in a significant increase in the required volumetric throughput through the PIR process. This has placed even greater emphasis on improving the stability of the solid phase produced in the autoclave, ultimately targeting an easily filterable residue with high iron content."

Jan 1, 2016

By H. C. Counsell, R. Webber

"The mill at Denison Mines' Elliot Lake Operations started up in 1957, with a capacity of 6,000 tons per day. Over the years various plant modifications expanded th.is to 7 500 tons per day. In 1976, management decided to carry out a major expansion of the milling capacity, and during 1980 the grinding capacity was increased to 15,000 tons per day.The original comminution system consisted of a conventional crushing plant feeding minus S/s-inch material to rod and pebble mills, in closed circuit with mechanical classifiers. The key decision that had to be made was whether the expansion should include conventional or autogenous grinding flow sheets.During 1977, extensive pilot plant studies at Lakefield Research showed that two-stage semi-autogenous grinding, with some steel media in the primary mill and with pebble media in the second stage, produced stable grinding conditions. This type of circuit was selected by Denison for the expansion, and went into production in 1980. Primary millThe flow sheet of the semi-autogenous grinding circuit is shown in Figure 1. The primary grinding mill is a Koppers 28 foot by 10 foot mill, driven by a 4,000 h.p. synchronous motor. It is fed with a minus 8-inch run-of-mine ore, and 4-inch grinding balls are added as supplementary grinding media. There are two Koppers 15.5 foot by 22 foot secondary pebble mills, driven with 1500 h.p. synchronous motors. Each grinding stage operates in closed circuit with cyclones, and the primary cyclone overflow is the feed to the secondary mills. The circulating load in the primary stage can be controlled by adjusting the cyclone apexes."

Jan 1, 1984

By S. K. Schwartz

"This paper describes the general layout of the environmental monitoring scheme at Devco &apos;s No. 26 Colliery, including wall face ventilation, fan performance and methane drainage, and then goes on to discuss the sensors, the outstation layout, the surf ace control room and the protection of the system.IntroductionCape Breton coal mines have been pioneers in the use of the latest technology in mining coal on this continent. To mention just one example, continuous methane monitoring at the coal face was started in 1976 and the idea of automatically stopping the face conveyor during high gas levels using the face signalling system was conceived and developed by CBDC engineers.With the introduction of remote environmental monitoring, No. 26 Colliery will be the first underground coal mine in Canada and possibly in North America to have computer-based comprehensive environmental monitoring.Traditionally, surveillance of the mine environment has been based mainly on periodic checks by portable or hand-held monitors. Although this method proved adequate, it has some limitations, namely:1) restricted &apos;number of observations and samples;2) relatively long time between taking measurements and availability of results for assessment.With remote monitoring, the above limitations are overcome because (a) monitoring is continuous and (b) monitored data are updated quickly (typically 5-7 sec.). Remote monitoring also provides a centralized &apos;information center&apos; at the surface from where the entire mine environment can be monitored. Details of modes in which data can be displayed and features available at the location will be discussed later in the paper."

Jan 1, 1982

By Joel T. Werner

Tire costs represent one of the highest controllable costs in open-pit mining, accounting for approximately 10% of mining costs. Tire monitoring technology has evolved rapidly in recent years and is emerging as a viable tool for extending tire life and reducing costs. The majority of the major tire manufacturers and several independent companies are in various stages of developing monitoring systems that capture and store vital tire data. Previously this information had only been accessible when the vehicle passed a fixed point in the mine, or when mine personnel manually downloaded the data. Integrating this technology with a mine management system enables remote collection and management of trend and alarm data. Mine personnel can now monitor a tire?s health parameters at any time, anywhere on site, regardless of the vehicle?s location. Anomalous tire conditions can be detected early and corrective actions taken. This information can then be integrated with other major onboard systems, operating conditions, and geographical information. Tire monitoring no longer exists as a stand-alone technology, but has evolved into an important integrated tool for mine operators. This paper will review the current status and benefits of integrating this emerging technology with a real-time mine management system.

May 1, 2002

By Grant Goddard

Cameco?s ?Double U? Strategy ? Double existing production ? To 40 million lbs U3O8 annually ? By 2018 ? Existing operations ? Saskatchewan ? United States ? Kazakhstan ? Projects under evaluation ? McArthur River expansion ? Kintyre (Australia) ? Inkai Block 3 (Kazakhstan) ? Development properties ? Cigar Lake project Measures of Success ? Safe, healthy and rewarding workplace ? Supportive communities ? Clean environment ? Outstanding financial performance

Nov 1, 2011

Mining Subscribes to Murphy?s Law Personal observations on the past ?Perfect, benign deposit mines can be screwed up-spills and concentrate handling issues ?Long term contamination and water management assessments inadequate ?The ?permitting mentality? and its effects on the application of proponent and regulator resources ?Reliance on simple principles but nature and chemistry is more complex

May 1, 2010

By Alexander Potapov, Lawrence Nordell

A Conjugate Anvil-Hammer Mill (CAHM) has the potential to replace conventional crushers and SAG mills, with their respective conveyors and stockpiles, in a SABC circuit. It may improve comminution circuit efficiency by 100%. CAHM compresses rock in a more efficient way, similar to 19th century stamp mills, which follows the fundamental research of Schönert (1990 & 1996). CAHM efficiency is being proven through the use of ROCKY (2011) Discrete Element Method (DEM). ROCKY features allow it to simulate realistic comminution. CAHM is customizable with many geometries that are rock-property specific. ROCKY’s wear modeling compliments the structural integrity of the design.

Jan 1, 2012

By Mario E. Rossi

The full economic evaluation of a mining project requires a block model that provides an estimate of the tons and grades of available resources. The model must be representative of the mineralization to be found at the time of mining for specified extraction periods and within acceptable error margins. In an operating mine, there may be a reasonable understanding and estimates of actual dilution and ore loss. This paper discusses the issue from the perspective of a project at a feasibility or preproduction level of development. Three types of dilution are discussed. Internal dilution (or change of support) is function of the spatial distribution of the mineralization and its relation to the operation?s selectivity. Geologic contact dilution is the unavoidable mixture at contacts or boundaries of material with different geologic characteristics, grades, or metallurgical performance. Operational planned and unplanned dilution should also be considered, sometimes incorporated by factoring the resource model, but more accurately by mimicking the grade control process. The resource estimation process always carries uncertainty, which is sometimes significant, and usually caused by several factors. These include quantity and quality of drill hole information; quantity and quality of geologic data; grade estimation methodology; dilution and mining recovery factors applied; etc. A key decision is to whether estimate as accurately as possible the in-situ geologic resource or to estimate the tons and grade of the material to be fed to the processing plant. The geologic modeling and grade estimation methods used are conditioned by this decision.

May 1, 2009

By Song Mao, Local Joint Engineering Lab of Efficient Util of Dominant Mineral Resources from Karst Regions, Guizhou Key Lab of Comprehensive Utilization of Non-metallic Mineral Resource, Xianhai Li, Qin Zhang, unjian Ye, Guizhou University, Wei Cheng, Zhihong Liu

"Phosphate tailing is a kind of industrial waste that emitted from separation processing of phosphate ores, which is usually discarged to the tailing pond without treatment. Recovery of phosphorus from tailings is of great significance for comprehensive utilization of phosphorus resource. Chemical composition of a micro-fine cryptocrystalline phosphate tailing was investigated by X Ray Fluorescence (XRF) and Inductively Coupled Plasma-Atomic Emission Spectrometry (ICP-AES), and mineral composition and occurrence of harmful elements were analyzed by optical microscope and Scanning Electron Microscope (SEM), X ray Energy Dispersive Spectrometer (X-ray EDS) and Mineral liberation Analyzer (MLA). On the basis of above, effects of those on mineral processing for phosphate tailing was analyzed. Chemical analysis results in combination with microscopy indicated that there is a certain amount of iron and aluminum and it should focus on the removal of them in separation processing. The cryptocrystalline structure, especially the micro banding structure and micro porphyritic structure indicated that there is quite amount of phosphate in fine particles and it should recovery the phosphorus as much as possible when designing the flotation technology for this difficult separation fine phosphate tailing. This study can provide theoretical guide for efficient phosphorus recovery of from fine phosphate tailing by flotation.INTRODUCTIONPhosphate rocks are vital nonrenewable resources and are essential components in agricultural fertilizers and phosphorous-based chemicals (Gharabaghi et al., 2009). About 95% of the phosphate produced around the world is consumed in the fertilizer industry (page 60 Abdel-Zaher, 2008; Jasinski, 2007). Froth flotation, a solid wettability based separation process is widely used in separation of phosphate rock and shown to be effective (Yehia et al., 1990; Singh et al., 1992; Elgillani and Abouzeid, 1993; Al-Fariss et al., 2013) .Poor selectivity and low recovery for micro-fine particles are hard issues in flotation of middle-low grade phosphate ore because Phosphate resources is becoming poor, fine and complex as the rich ores run out since the 1970s. The rapid depletion of high grade ores forces minerals industry to process low grade ores where finer grinding is required to achieve required liberation of the values, making the fine particle flotation inevitable. the performance of conventional flotation deteriorates rapidly as particle size decreases to below 10-20 µm, depending on the density of the particles (Feng and Aldrich, 1999). To date, fine particle flotation is still considered to be a challenge in mineral processing (Li et al., 2015) ."

Jan 1, 2016

By Ferrin Prince

New Gold?s New Afton mine is an 11,000 tonne per day block caving mine, located 8 km west of the city of Kamloops, British Columbia. The reserve is estimated at 52.5Mt with grades of 0.65 g/t Au and 0.93% Cu. Block caving requires a considerable amount of infrastructure development before production can begin. Each excavation had its own challenges, often further complicated by interactions with the caving stresses and fault structures. The main areas of interest were: the production crusher complex, the surface to underground infrastructure, and the footprint interaction with the faults. The ore zone at New Afton is bounded by two very weak fault zones, with large fault affected areas and associated splays. The resulting rock mass rating (RMR) is 35-50, with some areas significantly weaker due to clay infill. These conditions created a unique and decidedly difficult environment in which to develop New Afton?s infrastructure. Despite these difficulties, the mine began production on schedule in July 2012. The main production crusher for the mine is a gyratory crusher that allows for direct truck dumping, with a smaller jaw crusher in series to facilitate the initial development and production. The crusher chamber was redesigned several times to minimize the chamber volume, resulting in a 40% decrease in volume without losing functionality. After drilling and geotechnical testing, the location of the crusher was changed to eliminate the threat of fault affected ground in the area; the entire complex moved a short time before mining began on the chamber. The mining techniques used enabled tight control of the crusher pocket excavation, while also allowing for the timely completion of the chamber. The locations of the surface to underground infrastructure were tightly constrained by geology, surface infrastructure, and an existing open pit. The VR5 raise was drilled and abandoned part way through the reaming process when the drill string became stuck in fault gouge material. It was relocated and successfully completed. The VR7 raise hit a region of poor rock strength and deviated more than 11 m. Poor ground conditions caused a 130m section of the raise walls to fail. An innovative rehabilitation program was undertaken to re-establish the raise for ventilation. A surface to underground slick line was also installed to ease the material movement underground. A layout of the Extraction level was changed from herring bone to straight through drawpoints that resulted in a net reduction of 1.3 km of development. The Apex level was added to aid in the breakage over the major apex pillar and allow for geological mapping. A portion of the caving footprint is located within the footwall fault. The low strength, high clay content, and small joint spacing of the material resulted in blast-hole cut-off and drift deformation. Drift rehabilitation was a key factor in the successful development of the cave footprint. Innovative drilling and loading techniques were used to keep the holes open and to impede movement along the joint structures.

Aug 1, 2013