Search Documents

By John Hoffert, Darren Colwell, Greg Tucker, Jeremy Kinch, Greg Rasmussen

"The Kemess Mine, a major producer of gold and copper, is located in north-central British Columbia. Kemess was brought into production in May 1998 by Royal Oak Mines. On February 11, 2000 Northgate Exploration Limited acquired Kemess Mine from receivership. Since acquisition in 2000 Kemess has seen many accomplishments, including the reduction of costs by 40%.One of the largest site capital costs was the construction of the tailings storage facility dam, which when finished will be one of the largest earth filled dam structures of its type. The existing construction design by AMEC called for a kilometer wide rock dam to be built from the 1350 M elevation to the 1504 M elevation at a 5.5:1 slope by hauling over 30 million tonnes of non-acid generating waste rock 7-kilometers from the open pit to the tailings dam, which was highly expensive.Kemess realized an opportunity for cost reduction was possible if the dam could be built from suitable quality tailings sand; however the sand did not meet the neutralizing potential ratio specifications. It was determined that cycloning combined with flotation to reduce pyrite concentration in the sand would produce a non-acid generating product for dam construction. The sand plant design challenges were to remove the sulphides from the tailings to obtain an NPR greater than 2:1 and provide a consistent sand product for the construction with a fines content of less than 15% passing 200 mesh. After a 2-year testing design and construction period, the sand plant was successfully started at the end 2002 resulting in higher than expected sand quality and production rates.This paper describes the plant design phase, commissioning, and operation of the tailings sand plant for construction of the tailing storage facility dam to enable us to meet all the engineering and regulatory requirements. The many challenges faced were successfully met using several innovative designs. The operational, economic, and environmental benefits are detailed."

Jan 1, 2004

By Gustavo Angeloci

Artisanal mining is a rudimentary activity that today attracts over 30 million people in virtually all developing countries around the world. As the price of gold has steadily increased over the past decade, 15 million people have become involved in extracting this metal in 55 countries. Individuals have switched to mining from primary industrial sectors such as agriculture to increase their income. These workers generally have little capital, low education levels, and no previous experience in mining. Together with a lack of technical support from governments, these factors lead to disorganized and informal mining activities that generate environmental and social chaos. The absence of technical knowledge and capital has caused a proliferation of Gold Ore Processing Centres (GOPCs) around the world established by local entrepreneurs, who provide a way for miners to process their ores using amalgamation for a fee that is relatively low to non-existent. Gold recovery by the independent miners rarely exceeds 30 % and gold-rich tailings are left at GOPC facilities as a form of payment. GOPCs recover around 90 % of the remaining gold using cyanidation, flotation, and amalgamation, without any compensation paid to the miners. In processing these mercury (Hg)-contaminated tailings, Hg cyanide complexes are produced that are dumped into aquatic environments, leading to rapid bioaccumulation of Hg by fish. In the town of Portovelo, Ecuador, the establishment of partnerships between GOPC entrepreneurs and artisanal miners has proven to be successful in forming legal small-mining companies to create more equity and reduce pollution. About 108 GOPCs operate in Portovelo-Zaruma, with 40 % of these still working illegally without proper regulation and permitting. Over 20 % of these GOPCs continue to use grinding, concentrating and amalgamating of the gold, with 58 % performing cyanidation of tailings and/or gravity concentrates, and 15 % combining flotation with cyanidation. About 94 % of the GOPCs concentrate the ore prior to applying amalgamation, which significantly reduces Hg emissions to the environment. Incorporating flotation has given the operators increased skills in mineral recovery, with the side benefit of producing a copper concentrate as added value. Despite these innovations, mineral recovery is still inefficient, and waste management is a major challenge in creating true sustainability in this sector (technical efficiency together with social and environmental responsibilities). Further organization, training and capacity-building are needed. The principles of Lean Manufacturing Methods ("Just in Time" production and "Automation") are suggested as possible techniques to assist small GOPCs to become sustainable. In this concept, a larger mining company can become associated with artisanal miners in a partnership to provide training and investment for exploitation of small deposits that would be infeasible as a single large operation. As well, an International Training Centre for Artisanal Miners (ITCAM) is being established in Portovelo with collaboration of the Government of Ecuador to further enhance and upgrade mining activities in this region. ITCAM will provide artisanal miners with technical, business and environmental training to become responsible small-scale miners. In building this new capacity, ITCAM intends to create an atmosphere of trust to attract private and corporate investors to become partners with artisanal miners.

Aug 1, 2013

By B. Morrison

"The Kiruna Electric System is a recently developed inclined ore haul age system for underground mining operations. Although an initial investigation was carried out at the Swedish underground iron ore mine LKAB almost three decades ago, it was not until 1981 that the resources of LKAB, ASEA and Kiruna Truck AB were combined to investigate, and subsequently develop an ""all- electric truck"" for the mining industry.It has long been appreciated, that major economical advantages could be realized by a mining operation through an extension of the cost-effective life of the existing ore hoisting system by the use of ramps to haul ore up to the main haulage level. Diesel truck s have been used and are being used for ramp haulage. Their use however, is limited due to ventilation and operating costs restraints.There are numerous instances of orebodies, located within a couple of hundred metre s of surface, or below an existing hoisting facility, being developed by ramp access while the shaft is being sunk. Development of an orebody via ramp access has many advantages to a mining operation where mechanized mining is to be practiced. These advantages are both practical and economical; generally falling within the over-all umbrella of the phrase ""cash flow"" mining.The decision to sink a shaft is a major committment by any mining company, regardless of size and financial reserves. Extensive diamond drilling, both shallow and deep must be carried out before a decision can be executed. This constitutes a major financial expenditure over an extended period of time.The decision to sink a shaft must be weighed against the reliability of geological interpretation of the deep diamond drilling results, the stability of the mineral market and potential fluctuation in ore prices and interest rates."

Jan 1, 1989

By P. Hajiani

"Feasible and sustainable separation of lanthanides outside of China has been a dilemma for the past few years. The present technique uses REE electrophoretic mobility (Ui) variation in an electrical field to separate them. The present invention relates to a system and a method to separate and refine rare earth elements/compounds produced in hydrometallurgical processes while they are dissolved in an acidic medium, without any intermediate precipitation step. This process uses free-flow electrophoresis to isolate REE from the concentrate simultaneously without any pre-treatment or intermediate steps related to the nature of elements.INTRODUCTIONRare earth elements (REE) invariably occur together in nature, and any given mineral contains several or most of them. Production of high purity individual rare earth (RE) elements/compounds from their ores generally requires two stages of processing, including mineral processing and hydrometallurgy.Depending on the ore, mineral processing and hydrometallurgy treatment of the ore before REEs purification is relatively simple and quite achievable though conventional methods. However, producing individual REE from mixed REs compounds is tremendously tedious. RE processing often requires dozens of steps, each resulting in minute improvement in the complex RE streams. Separating and extracting a single REE requires a great deal of time, resources, and expertise. Today, advanced RE refinery facilities cost hundreds of millions of dollars to build. The high purity RE concentrates are separated into individual REE using solvent-based or ion exchange methods. Although there are several techniques to separate REEs, most of them suffer from different types of drawbacks. For instance, solvent extraction requires a great number of steps to achieve high purity REEs. The process which uses ion-exchanger for separation and refinery operates with low REE concentration in solution which leads to very large liquid volume quantity, bulky tanks, dehydrators, pumps, etc. The low concentration will adversely affect the water consumption as well as other chemicals. Similar chemical properties of those three valent elements do not allow them to be isolated easily one from one another using conventional separation techniques. Solvent extraction has been successfully applied for rare-earth refining (lanthanide, scandium and yttrium) for the past few decades in China. Since then, efforts have been dedicated to develop other techniques which could be applied industrially around the world."

Jan 1, 2016

By Frank van der Meer, Jorge Portocarrero, Alexandra Gruendken

"The number of High Pressure Grinding Rolls (“HPGRs”, also called Roller Press) installations instead of tertiary crushers is rapidly increasing. The technology has been largely accepted in the minerals industry and benefits, such as superior energy efficiency and a lower overall operating cost compared to alternative technologies, have been demonstrated at a number of operations throughout the world.This paper focuses on coarse hard ore operations and reviews the successful installation of the first Roller Press installed instead of a tertiary crusher at the Los Colorados Plant of CMH (Chile) in 1998. It details the experience obtained over the past ten years of operation from commissioning to the present day. It highlights examples of further developments made in the design to improve machine maintainability and availability as well as wear life of the grinding surfaces.A second focus lies on procedures to derive from small scale testing material properties such as wear life, flake formation and strength and their application to industrial size machines to optimize circuit design, especially when Roller Presses are used in closed circuit with screening.INTRODUCTIONRoller Presses (also known as HPGR, High Pressure Grinding Rolls) are considered today state of the art for the preparation of pellet feed. They are also gaining wide acceptance in coarse ore operations. One of the first successful operations in which a roller press was used to replace a conventional tertiary and quaternary crusher is the Los Colorados plant of CMH in Chile.When the Roller Press at Los Colorados was commissioned in 1988, there were 169 Humboldt Wedag roller presses in operation throughout the world. Of these, 14 were installed in the minerals industry. However, these were installed mainly for grinding pellet feed to increase the Blaine value. Up to that time, only three KHD roller presses had been applied for crushing coarse ore in specialized circuits. Moreover, the installation at Los Colorados was the first Roller Press ever to replace a conventional tertiary and quaternary crusher in a hard ore application."

Jan 1, 2009

By A. Mykytiuk, I. E. Puddington, W. D. Macleod, F. W. Meadus

"A laboratory-scale continuous procedure for the up-grading of naturally occurring tin ores, based on the principle of spherical agglomeration, is described. High recoveries are indicated. A proposed second stage suggests useful fractionation steps.IntroductionA LABORATORY-SCALE batch process for the upgrading of a tin ore using the principles of spherical agglomeration has already been described (1). This procedure consisted of milling, for about an hour, a precrushed ore with at least 200 per cent water, 0.2 per cent of a reagent such as tall oil (to render the de-sired ore particles hydrophobic) and about 3 per cent of a viscous petroleum oil. The feed material passed an 8-mesh Tyler sieve, and the percentages of re-agents are based on the dry weight of the feed. Du-ring the grinding, the hydrophobic particles transfer into the oil phase to produce coherent semi-solid bodies while the gangue stays preferentially in the aqueous phase. The concentrate can be separated from the gangue easily by a mechanical operation. Using an ore containing about 0.3 -0.5 per cent tin, grades of from 1.5 to 7.0 per cent were obtained by varying the pH of the system. Recoveries fell from about 80 per cent to as low as 50 per cent as the grade in-creased."

Jan 1, 1966

By N. Manopulo, J. Maier, L. Tong, C. Becker, P. Hora

The contribution presents a new finite element approach in which the common updated Lagrangian formulation is replaced by a spatial flow formulation applying a special arbitrary Lagrangian-Eulerian for-mulation (ALE). The description separates spatially the process in a die inside zone and in a profile zone. For the description of the inside zone, where the filling process occurs, a special Euler time independent mesh is applied. By this formulation the mesh has to be generated only once, which simplifies the generation of spatially optimized meshes. For mapping of the material flow during the filling process the method uses a flow surface traction method as applied in casting simulations. A further strength of the new method is the computational efficiency which allows the modelling of extrusion process with the highest complexity with a response time of 12 hours, which is important for the industrial optimization process.

Jan 1, 2015

By A. Jordens, Y. Zhiyong

"IMBSRE, one of the largest rare earth element (REE) producers in China, produces a rare earth oxide (REO) concentrate as a by-product by floating the middlings stream from a low intensity magnetic separation step in the main iron ore processing stage. As the mine depth has increased, flowsheet changes in the main iron ore circuit have reduced the REO grade and increased the magnetite to REO ratio in the middling product used as flotation feed for the REO circuit. Extensive laboratory work was carried out and identified a new modified hydroxamic acid product, Florrea 8920, that could provide better metallurgical results over the standard hydroxamic acid used as the main collector. This paper briefly reviews the use of hydroxamates in the flotation of oxide minerals, provides detailed information on the different hydroxamates available from Florrea and then provides a case study of the successful implementation of the Florrea 8920 product in a commercial Chinese REE flotation plant. The case study consists of a one year program of pilot plant testing and industrial trials to confirm the results of laboratory tests. The implementation of the new collector resulted in an improvement in grade and recovery to 61% and 64% respectively. The new collector also provided significant economic and environmental benefits.INTRODUCTIONThe flotation of rare earth element (REE) bearing minerals is a topic which has been dominated in the English language literature by the work conducted on the Mountain Pass bastnäsite deposit (Pradip, 1981; Fuerstenau, Pradip, Khan, & Raghavan, 1982; Pradip & Fuerstenau, 1983, 1985, 2013; Fuerstenau & Pradip, 1991; Fuerstenau, Pradip, & Herrera-Urbina, 1992; Herrera-Urbina, Pradip, & Fuerstenau, 2013). By far the most important collector type used for the flotation of rare earth minerals (REM) is hydroxamates. These reagents were initially extensively described as REM collectors in the English literature by Pradip (1981) however they have been successfully applied to numerous other minerals such as: cassiterite (Sreenivas & Padmanabhan, 2002); pyrochlore (Gibson, Kelebek, Aghamirian, & Yu, 2015); hematite, chrysocolla, rhodonite, hubnerite and pyrolusite (Fuerstenau, 2005); and malachite (Lenormand, Salman, & Yoon, 1979) amongst others."

Jan 1, 2016

By Richard F. Lynch, Frank E. Goodwin

"The development of Galfan, a new generation 95% zinc-5% aluminum-mischmetal alloy coating for steel, offers opportunities for greater fabrication flexibility and upgraded corrosion performance in automotive applications. The formability of Galfan is equivalent to that of electrogalvanized steel, based on laboratory tests and automotive component fabrication. Corrosion resistance of Galfan exceeds that of hot dip and electrogalvanized, including performance in automotive industry tests. Automotive production applications for deep drawn and stamped components in France and Germany are based on the ability to meet dual performance requirements for upgraded formability and corrosion resistance. The first U.S. Galfan application was on 1985 model Ford cars and light trucks for transmission oil cooler lines which has now expanded into a number of power steering tubing uses. IntroductionContinuing requirements for improved vehicle performance coupled with the ever present need for reduced cost have spawned the development of a number of new coated steel products. Among this new generation of coated steels is Gaifan™, a 95070 zinc-Solo aluminum-mischmetal hot dip alloy coating. Galfan exhibits particular promise for automotive use based on broad fabrication advantages and upgraded product performance(I ),The unique characteristic of Galfan is the key combination of greatly improved formability with much longer corrosion life. Galfan provides significantly better formability than any other hot dip coating. Testing shows that formability is limited primarily by the steel substrate to which the Galfan coating is applied. Galfan exhibits excellent resistance to flaking and microcracking during commercial forming operations. The result is the elimination of unnoticed damage to the coating which would show up later as premature rusting on the finished product."

Jan 1, 1987

By Edward Sampson

Bases of National Power At a time when the economy of the world is in a particularly troubled state it is appropriate to examine some problems of the distribution of natural resources. I should like particularly to call attention to the remarkable increasing demand for natural resources, to give an analysis of the demand for certain mineral resources, and to direct attention to some problems in satisfying this demand. All industrial power is based on natural resources and the most basic of these are soils, energy resources, and mineral resources. There is a strong interrelation of these resources, more than is obvious, and I shall take up certain aspects from the point of view of a geologist. Few nations are well endowed with all three of the kinds of natural resources I have mentioned and much has been done by some small countries whose peoples are industrious and enterprising and where conditions for free world trade have been favourable. However, major industrial power is dependent on a substantial endowment of all three classes.

Jan 1, 1949

By M. Ghiani, P. Carbini, R. Ciccu, C. Del Fà

"This paper is concerned with the problems inherent in the efficient and economical processing of the fine fractions of a coal from the Sulcis basin (Sardinia, Italy) whose characteristics are typical of low-rank coals occurring in the Mediterranean region. Three different techniques, based upon surface properties, are examined. Flotation can be very efficient from both a technical and economic point of view, provided care is taken in the modulation of the flotation pulp. Interesting results have been obtained with oil agglomeration and this method could be economically feasible. Finally, electrical separation has proven a viable technique, although it entails preliminary drying.Besides discussing the problems encountered in the experimental research, some significant results of general validity are also given. They demonstrate that cleaned products can be obtained with fairly interesting recoveries, thus opening the way to advanced research aimed at setting up the most suitable technique for industrial application. IntroductionAs a result of the oil crisis, which caused a major upset in world energy supplies, the last ten years have seen a revolution in the energy policies adopted.In particular, the status of coal, which seemed destined to decline in view of the availability of liquid fuel, has had to be re-examined. The need to meet energy demands under improved reliability conditions and controlled prices through a broader and more flexible diversification of sources of supply has evoked, especially in highly industrialized countries, a renewed interest in coal. The result has been a consistent increase in demand and production as well as investments in new mines and the reinforcement of the infrastructure.This turn of events has also lead to a re-evaluation of young low-rank coals, hitherto considered uneconomical and thus neglected, because of their low heat value. In fact these coals, which have a high ash content, may also be relatively highly contaminated with sulphur. The above drawbacks, which still today preclude the widespread use of these coals, are bound to create even greater problems in the future as increasingly restrictive environmental control imposes, without exception, recourse to cleaner fuels."

Jan 1, 1986

By D. Brand

"The risk management objective of the AMIRA Code of Practice for Metal Accounting has seldom been systematically investigated in the literature up to the authors’ knowledge. Risk is defined in the Australian Standard on Risk Management (AS/NZS 4360:2004), as “the chance of something happening that will have an impact on objectives”. The simplified economic analysis performed in this paper has lead to define “something happening” as measurement non-representativity and “impact on objectives” as NSR loss from the optimal NSR. This has pinpointed a missing link being the establishment of a relation between NSR in flotation plants and measurement representativity. The proposed framework, referred to as the total cost of representativity, answers the previously unanswered question of how much accuracy/reproducibility is fit for purpose in a given flotation plant. Authors readily acknowledge that it is way easier to assess the cost of accuracy/reproducibility than the cost of inaccuracy/irreproducibility. However, this exercise not only answers previously unanswered questions but also establishes an essential link with operational excellence. This paper exposes why such operational excellence could neither be attained nor proved without a state of the art metal accounting system. This should impact not only how metal accounting systems are audited/designed/refactored, but also how flotation plants are designed.IntroductionBecause representative metal accounting is a vital source of information for the financial accounts of a mining/metallurgical company, the need for a code on metal accounting was recognized in 2001 and a team was formed in 2003, under the sponsorship of several major mining houses, to produce such a code. Table 1 exposes the two main objectives of this AMIRA Code of Practice for Metal Accounting."

Jan 1, 2017

By Z. Huda

The effect of various percentages of cold-working and recrystallization on the microstructure and hardness of commercially-pure aluminum plate, has been studied. The 'A critical deformation for the aluminum, has been determined. Experimentation involved cold rolling and recrystallization processes followed by quantitative metallographic practice and the hardness measurements. The raw material chosen was a plate of commercial aluminum which was cold rolled to different percentage of cold-work and then recrystallized by heat treatment at 150°C. The critical deformation percentage of aluminum was computed to be around 30% of cold-worked.

Jan 1, 2007

By T. Marolt, J. Likar, E. Grøv, J. Žarn

"Underground structures are an integral part of the infrastructure of modern society and are used for a wide range of applications, including subways and railways, highways, not at least nuclear facilities. When the wider area is subject to earthquake activity, underground constructions should be analyzed on seismic and static loading. Observations showed that the underground structures have significantly less seismic risk than surface structures. Available methods allowed analyzing the magnitude of risk for different input parameters of seismic loads in different ground environment. Simulation of earthquake loading on underground structures, in the present paper is given the various aspects of analyzing the potential damage and instability of underground facilities. INTRODUCTIONThe development of methods and computing resources used for para-seismic engineering has finetuned the evaluation of the seismic strength of buildings and equipment. Reinforcements may therefore be decided, not simply on the basis of a reassessment of the hazard, which constitutes input data for the calculation of structures and equipment, but also on the basis of developments in para-seismic engineering. Underground facilities are an integral part of the infrastructure of modern society and are used for a wide range of applications, including subways and railways, highways, material storage, and sewage and water transport and not at least nuclear facilities. Although in the past showed that the underground structures are significantly less seismic risk than on the surface, the professional researches and their results are accessible. Seismic resistance of underground structures is analyzed from several aspects. The currently available methods allowed analyzing the magnitude of risk for different input parameters of seismic loads in different ground environment. For better interpretation of earthquake loading on underground structures, are given below the various aspects of analyzing the potential damage and instability of underground facilities in rock. One of the early studies which covered this are of investigation were prepared by Dowding and Rozen (1978). They grouped damages due to earthquakes in underground structures into three main categories:- damage from ground shaking- damage from fault dislocation- damage by earthquake-induced ground failures (e.g. liquefaction and landslides)."

Jan 1, 2015

By V. Estrada, G. Aguilera

"Since the most of mineral processing are wet, and for more specific applications where it is necessary to increase the purity through leaching and / or concentration, the proper dispersion is the first, and perhaps more crucial stage in the whole chain of processing. This specific process is based on the formation of a dispersion or suspension of mineral, trying to make the mixture as homogeneous as possible, and with specific rheological conditions. Sometimes it is not enough agitation to make it happen, so that chemical additives are used as an aid. However, the addition of chemicals strongly alters the viscosity and other rheological properties of the suspension factor to consider for subsequent steps to ore beneficiation. In other hand, in a process where no chemicals used often employ large quantities of water to achieve dispersion. But if an efficient chemical agent, which optimizes said dispersion through a specific physicochemical effect on the particle surface is used, also it can generate rheological advantages, besides achieving rational use of water and increase the recoveries of the product main about also optimal costs. The aim of this work is to find the optimal rheological conditions for a dispersion of kaolin as study case, looking for stability, best disaggregation, viscosity and pseudoplasticity.To find the optimal additive, the evaluation parameters were: 1) Best degree of dispersion of the suspensions according to the analysis of the flow curve; 2) Best level of disaggregation of particle chemical analysis delaminated by Particle Size Distribution; and 3) Best thixotropic rheological parameters and pseudoplasticity. Finally the optimum additive as one that meets the best combination of parameters is proposed.INTRODUCTIONKaolin is a clay material formed by altering of feldspar composed mainly for kaolinite. Depending on the application, the kaolin as raw material must be refined and processed because the ores of clays contain usually a lot of impurities derived of its sedimentary source, such as feldspar, mica and quartz (Torres, et. al., 2011). According to the experience on the plant floor and the publication of several scientific papers, it is known that the dispersion is a crucial stage in mineral processing (Greene, Duke, & Hunter, 1965) (Raghavan, et. al., 2004), not only because of the disaggregation of particles, besides because of the humectation of them. Is clear that disaggregation of particles give to the suspensions rheological stability, and the humectation improves the effect of further processes like grinding or chemical treatment. The dispersion process involves making a suspension of the mineral with a solvent which is usually water, to obtain a homogeneous dispersion, with the aid of energy of stirring. Sometimes is not enough the agitation (even with high energy) for this to occur, so is necessary the use of dispersing substances which introduce ions and molecules as modifiers of chemical potential, forcing the molecules of the material to disperse. Sometimes their use even could affect the pH of the suspension in a non-desirable condition. (Flores, 2013)."

Jan 1, 2016

By D. M. Maijer, S. M. Mohseni, A. B. Phillion

The microstructure evolution kinetics of aluminum alloy B206 during artificial aging has been investigated using non-isothermal calorimetry. A combination of differential-scanning calorimetry (DSC) and tensile tests have been utilized to develop an Avrami model to predict the precipitation kinetics as a function of the thermal processing parameters. The Avrami coefficients, found based on a Kissinger analysis, compare well against those reported in the literature for aluminum-copper alloys. The rapid precipitation kinetics predicted by the Avrami model at temperatures higher than 200°C were assessed through a qualitative comparison against hardness measurement results. In contrast to the continuous hardening observed at 150°C, the material softens with continuing heat treatment at 250°C resulting in an overaged state. This can be attributed to the rapid precipitation kinetics at this temperature, leading to the termination of the precipitation-hardening effects at early stages of artificial aging.

Jan 1, 2015

By Joe Shoemaker

Automated Spot Generation ? No Operators below the Highwall ? No Operator Wear and Tear ? Reduced Swing Time ? Single and Double Sided Loading ? Minimized Bench Width

Aug 1, 2013

ABSTRACT The inevitable uncertainty in modelling spatial variables decreases as more data become available. This reduction depends on the properties of the variable being modelled. Spatially continuous variables show less uncertainty for a given spacing than erratic variables. A geostatistical simulation based approach is developed to quantify the relationship between uncertainty and data spacing. Reference realizations are sampled to condition additional realizations and quantify uncertainty. The procedure is automated, making it straightforward to consider sensitivity and different geological domains. A case study of the relationship between uncertainty and data spacing for net oil sands thickness data from northern Alberta is presented. _ KEYWORDS Simulation, Sampling,

Jan 1, 2013

By T. I. Urbancic, C-I. Trifu

"ABSTRACTSeveral case studies are presented on the use of seismic techniques to map active structures, evaluate changes in stress levels, and identify the conditions leading to large magnitude seismic events and the generation of rock-bursts in Canadian mines. The results suggest that microseismicity can be used to identify the orientation of active fractures; define regions of relatively high and low stress, and those most likely to host a rockburst; determine the role of local stress on observed shear failures; and identify the path of stress transfer associated with the remote triggering of rockbursts. Additionally, the conditions leading to rock-bursts can be characterized by a significant increase in the clustering of microseismic events along the fault plane orientation of an impending event, and an increase in the effective stress levels. It is concluded that the analysis of microseismicity provides the means for remotely monitoring rock mass behaviour as a result of mining."

Jan 1, 1997

By W. P. Clement, M. C. Bell

"PT International Nickel Indonesia, a subsidiary of Inco Limited, mines and processes nickel laterite ores for the supply of nickel matte, primarily to the Japanese market. It has large ore reserves and a substantial portion of its energy requirement is supplied from its own hydro-electric plant. Since the early 1980s, the company has increased its production level and has dramatically reduced its unit costs. Projects are in progress to further decrease costs and recently a major expansion - 31% increase in nominal capacity - has been undertaken, consistent with marketing opportunity in Japan. The expansion project, which has a low capital cost per unit of production, is outlined in this paper.IntroductionPT Inco is a fully integrated mining and smelting facility located in Indonesia on the island of Sulawesi, and is based on a very large, world class nickel laterite orebody located 60 km inland from the Gulf of Bone. Construction of a single furnace line plant started in 1973. Complete supporting infrastructure of townsite, hospital, schools, shopping centres, road systems, and an airport, all had to be built. Prior to completing the first phase, the decision to expand the plant to a three kiln-furnace line was made. A major factor in the decision was the ability to develop the hydroelectric potential of the nearby Larona River. This involved construction of a 30 m high dam, and a 7 km surface canal to the generating station. The penstocks drop 150m to three 55 Mw turbines. The power generated is sufficient to supply the entire electrical load for the complete smelting complex and town site. The unique capability to supply the high smelting energy requirements for a lateritic nickel ore by fully captive hydro power, has, over the past decade insulated PT Inco from the large upward swings in oil prices suffered by other lateritic nickel producers.Wet ore is first partially dried to 20% moisture in two co-currently fired rotary driers, screened on an internal trommel, and delivered to two dry ore storage buildings. The partially dried ore is calcined at 750°C and partially reduced in three large 100 m by 5.5 m kilns. Reduction is accomplished by lancing bunker C oil onto the ore bed at the discharge end of the kiln. The kilns are equipped with five air pipes with onboard blowers to gradually bum the combustible gases generated by the lance oil. The kilns were also originally equipped with two side burners to supply additional heat close to the feed end of the kiln. Calcined ore is transferred by 20 ton refractory lined containers to the furnace feed bins at the top of the smelter. Smelting is carried out in three 18 m diameter furnaces powered by 45 Mw transformers. Slag is skimmed at 1550°C through water cooled breast plates and removed to the slag dump by Haulmaster Carriers. Matte of 25% Ni, 1O% S, 65% Fe is tapped at 1350°C into the converter aisle. The iron is slagged in converters to produce a nickel sulphide matte at 80% Ni. Three rotary Kaldo converters were initially installed. The product matte is granulated, dried, and shipped in returnable rubber bags to Japan. Most of the matte is fluid-bed roasted to nickel oxide and then directly reduced in a second reducing fluid bed reactor at our facilities in Japan.The smelting complex was designed to smelt two million tonnes of dry ore per year, equivalent to 34 000 tonne nickel production at an ore grade of 2% Ni. The cost of the entire project including working capital was $900 million."

Jan 1, 1990