Search Documents

By George B. Saunders

It is the purpose of this paper to point out conditions as they exist in the merchandizing of coal, to compare these conditions with methods in use by competitive producers of coal substitutes, and to present briefly some suggestions which may help the individual operator to market more coal in the immediate future, while we are waiting for the scientist and research worker, who are now busy on coal betterment , to produce in a practical way the results which they now write about in such glowing terms. While it may be unnecessary to call the attention of coal operators to the present deplorable condition of the industry, it might be well to impress upon our members in other branches of mining, as well as upon the public at large, the seriousness of the situation. Emerging from the war and the period of reconstruction that followed, the coal industry found itself with too many mines and too many men for normal conditions. To make matters worse, the interruptions in deliveries caused by strikes, the unfavourable publicity caused by socialistic propaganda, and the repeated governmental investigations, made the market a fertile field for coal substitutes which were not so handicapped. These substitutes were well advertised, and were marketed in an up-to-date manner, furnishing an example from which the coal operator could well profit. Now, whether or not there is agreement as to the cause or causes of this condition, there can be no doubt that we are today face to face with the fact that the sale of coal has not kept pace with the sale and use of other commodities. Had it done so, we would ere this have been able to take care of the surplus labour and work our mines at least approximately full time.

Jan 1, 1929

By E. Landry, W. Naudts

"The amenability theory was developed by Alex Naudts and considers grouting operations as continuous permeability tests where Newtonian test fluid water, is replaced by a cementitious or solution grout. It utilizes hydraulic conductivity and grouting data to establish the amenability coefficient of a particular grout zone. The amenability coefficient reflects the quantity of apertures or voids accessible to the selected grout, divided by the number of apertures accessible to water, in the zone intersected by the grout hole. By calculating, in real time, the effectiveness of a particular grout at the start of a grouting operation, the most appropriate grout to match design criteria can be targeted. By incorporating the amenability theory in every grouting operation, schedule savings and an increase in productivity are typically achieved. Three short case studies illustrate different enhancements in productivity: At an underground mine during the construction of declines, a cement based suspension grouting program was highly ineffective and did not appear to affect the inflow into the mine workings. The amenability theory was utilized to evaluate the grouting program and based on this evaluation, changes to the grouting program were made which allowed the grouting to meet the project’s objectives. On another project, a pre-excavation grouting program implemented during shaft sinking operations utilized the amenability theory to select the most suitable grout for the program. Schedule constraints also influenced the selection of the grout. In the third case history presented, the amenability theory was used to select the grouting sequence of every individual grout hole for a grouting project in a highly heterogeneous soil formation. INTRODUCTION The amenability of a given soil, civil structure or rock formation for a particular grout formulation is a measure of the ability of that grout to permeate the pores, fissures and apertures water will flow through. The amenability coefficient of a particular grout for a specific zone equals the percentage of apertures, pores and fissures accessible by water that are also accessible by grout. Grouting should be viewed as a continuous permeability test, where the apparent in-situ hydraulic conductivity value for a particular grout zone is continuously evaluated, using grout instead of water as test fluid."

Jan 1, 2019

By Y. Kusuda

Since 1981, the Annaka refinery has recovered zinc from zinc leach residues by the Waelz Process. The important considerations of this process are the prevention of the growth of coating accretions in the Waelz kiln and the improvement of the zinc volatilization rate. In this paper, simulation predictions and the results of the industrial operation regarding the prevention of coating accretions in the Waelz kiln and the improvement of the zinc volatilization rate at the Annaka refinery are reported and compared.

Jan 1, 2006

By Atsuki Sado, Akira Ueno, Kazuaki Takebayashi, Kunio Watanabe

The Saganoseki Refinery of Pan Pacific Copper Co., Ltd., Japan, introduced the ISA 2000® process in 2006 to improve product quality and productivity. After resolving various technical difficulties associated with the process, a current density of 325 A/m2 and electrolytic copper production of 234 000 tons per year were realized in 2018. In recent years, Saganoseki Smelter & Refinery has promoted treatment of recycled materials in addition to copper concentrates. Accordingly, the amount and type of impurities charged to the smelting process have tended to increase. In the electrorefining process, impurities such as nickel and antimony cause anodic passivation and formation of suspended solids, respectively. Although these undesirable phenomena can be avoided by controlling impurity concentrations in the anode and electrolyte to appropriate ranges, this also limits the choice of recycled materials that can be processed by the smelter. To achieve both stable operation of the electrorefining process and flexibility in treatment of recycled materials in the smelting process, Saganoseki Refinery improved the capacity of the impurity recovery processes during 2016 to 2018. This paper describes the expansion of the purification plant to remove and recover nickel and antimony. INTRODUCTION The Saganoseki Refinery of Pan Pacific Copper Co., Ltd., Japan, introduced the ISA 2000® (wax- less permanent cathode method) in 2006 to improve product quality and productivity. Since then, the refinery has gradually increased current density, and has been committed to establishing stable operation and high productivity via various improvements related to the electrolyte filtration and additive management systems. Figure 1 shows the trends of current density and current efficiency at the refinery. Although the current efficiency temporarily dropped when the current density was raised to 322 A/m2, it consistently exceeded 97% thereafter. At present, stable operation at 325 A/m2 has been achieved and continues.

Jan 1, 2019

By V. C. Wansbrough

First, permit me to say with what very great pleasure we find ourselves assembled in this most ancient and honourable city of Quebec. It is a city which we deeply respect as the fountain-head of the culture of French-speaking fellow citizens, and the seat of government of a province which is steadily recording new achievements in Canadian mining. Such achievements prove what can be accomplished when enlightened and progressive government policy, technical and scientific competence, and private initiative pull forward together in harmonious rhythm. It is a most happy and auspicious event also that the guiding control of the affairs of the Institute and of the fine traditions of provincial administration have for the past year been united in the person of our honoured President, Dr. A. O. Dufresne. This year, again, we have bad prepared for us by our hosts a splendid programme of technical sessions and social entertainment. Each year we pay an unspoken compliment to the Institute, expecting as a matter of course nothing but the highest standards in both these spheres. In its annua1, semi-annual, and regional meetings, in the constant activity of its local Branches, the Institute continues with marked success to perform its great dual service, social and educational. We are all its beneficiaries to the extent to which we choose to profit by participation in its affairs. But, one imagines, to none are the advantages of Institute membership more valuable than to young men embarking on their professional careers.

Jan 1, 1951

By B. A. Monkman

"IntroductionONE OF :THE most effective methods by which the construction industry is combatting mounting building costs is by making increased use of lightweight materials, thus reducing the dead load to be carried •by structures. This applies to non-metallic materials as well as to metallic ones, and particular attention has been given to developing lightweight aggregates for use in concrete.The use of lightweight aggregates is not new and, in fact, dates back to the Roman Empire, when pumice was used in the walls and domes of the Roman buildings. More recently, and up to a decade or so ago, the demand for these aggregates was met from deposits of volcanic cinders, pumice, scoria, etc., and from the by-products of blast furnaces and coal burning boilers. However, these sources of supply are no longer sufficient to meet the demand, for transportation costs pretty well restrict the use of the natural lightweight aggregates to the western cordillera regions where the deposits of these materials occur, and the use of expanded slag aggregates to the areas neighbouring the plants where slags are produced. As for cinders, the supply has been greatly reduced by the conversion of industry to fuel oil, natural gas, and powdered coal, and the large stockpiles which existed previously have been pretty well exhausted.Industry's approach to the problem of a decreasing supply, in the face of an increasing demand, has been characteristically direct. The solution has been to construct plants whose sole .purpose is to produce economically an acceptable light-weight aggregate from materials close at hand."

Jan 1, 1955

By J. Dufour

Although the recovery of nitric and hydrofluoric acids from stainless steel pickle liquors has been solved by several methods, such as solvent extraction, acid retardation, evaporation or pyrohydrolysis, metals (mainly iron, chromium and nickel) are usually obtained as a waste or by-product that has to be disposed. Alternatively, the treatment requires a high liquor flow to be economical, as is the case for pyrohydrolysis. A new process has been developed for metals recovery, that produces metal oxides with a low fluoride content. This new technique is based on a selective precipitation mechanism, which produces nickel hydroxide with a purity of 90%, separate from a mixture of iron and chromium oxides and hydroxides suitable for recycling. The reaction mechanism is based on the precipitation of fluoride compounds of iron and chromium, K2FeF5 and CrF3. For this purpose, free fluoride must be added as potassium fluoride. Also, solid fluoride compounds are hydrolysed, releasing free fluoride. A part of the fluoride is recycled to the selective precipitation operation and the remainder is fed to the acid recovery stage. Nickel does not react in this operation; it remains in solution giving a high separation yield.

Jan 1, 2006

By Lyle F. Smith

With the demand for larger diameter raises under all ground conditions and the increasing price of drill rods and operating costs, it was evident that there was a need for a raise borer with a variable-speed drive and fast-response torque limiting control. The raise boring machine described in this paper was developed after several years of market research and discussions with mine operators and construction contractors. This paper discusses the Ingersoll-Rand raise borers with the solid-state controlled DC motor drives. These machines have gained wide acceptance in the five-year period since being placed in operation and are designed to accommodate the range of raise diameters and lengths most required today.

Jan 1, 1978

By V. Bonilla-Sierra, M. Elmouttie, L. Scholtès, F. V. Donzé

In the presence of joint sets sub-parallel to a slope face, the stability of the rock mass is controlled by the shear strength of the joints. On one hand, if the joints are persistent their shear strength can be assessed according to Mohr-Coulomb criterion, assuming appropriate values for the cohesion and the friction angle on the joint surface. On the other hand, if the joints are non-persistent with their continuity being interrupted by the presence of rock bridges, their shear strength will increase considerably. In this latter case, the contribution of the rock bridges to the shear strength of the joint has to be accounted for in order to better assess the stability of the rock mass. A numerical analysis of the progressive failure of a rock slope involving a non-persistent joint has been set up based upon simulations performed using a Discrete Element Method (DEM) algorithm specifically enhanced for the modeling of jointed rock masses. Pre-existing discontinuities are explicitly accounted for in the model by using a modified contact logic that ensures an explicit and constitutive mechanical behavior of the joint planes. In addition, rock bridges can be spatially distributed along these joint planes following a prescribed probabilistic technique. Jennings’ formulation (Jennings, 1970) is considered as one of the first rock slope analysis that evaluates the shear resistance to sliding as a weighted combination of the shear resistance of the intact rock and the joint planes. The validity of this formulation is discussed in the present study. Contrary to the Jennings’ formulation, we show that tensile failure is an important mechanism, particularly as the dip angle of the sliding plane increases.

Jan 1, 2015

By J E. McMynn

The development of the Granduc mine presents a number of problems which are peculiar to its location and surrounding terrain. Because the development tunnels portal onto an area which is covered by an extensive glacier, and the mountain-side is subjected to dangerous snow slides, it was decided to construct an underground powerhouse to supply the necessary electric power and compressed air. This paper deals with the special problems inherent in the design and -construction of an underground plant. It involves the installation of diesel-electric generating equipment having an aggregate capacity of 1,050 kw.,and of air compressors with a total capacity of 2,400 cfm. Items dis-cussed include the selection of equipment to meet site conditions, the ventilation and cooling of the underground room, and the protection of personnel and equipment from explosions and fire. A short discussion on the automatic supervisory and alarm installation is also included. THE Granduc mine is located 135 miles north of Prince Rupert and 25 miles north of Stew-art. This seems quite accessible, mileage-wise, but, due to mountains,

Jan 1, 1963

By S. A. Bunk, E. C. Eccleston, J. J. Amsden

Fluidized bed technology has been widely applied to mineral and metallurgical processes. Over the years, modeling of fluidization technology has progressed to a level at which basic design parameters can usually be defined based on empirical correlations. In addition, scale-up considerations have become better understood, and significant advances have been made in the area of computer simulation. Despite these advances, fluidization is a complex phenomenon, and modeling tools remain limited in their ability to simultaneously model both fluidization and chemical process parameters. As a result, almost all mineral and metallurgical applications of fluidized bed technology require pilot testing prior commercial scale design. This paper outlines pilot plant testing requirements and process development considerations for development of low technical risk commercial designs.

Jan 1, 2011

By R. J. Craig

Introduction All mining operations produce rock dust. Inhalation of rock dust, particularly if it has a high silica content, causes silicosis. Silicosis is, therefore, recognized as a hazard of the mining industry and has been made compensable throughout most of Canada. Most of the dust in any mining operation is caused by rock drilling and blasting operations and the movement and transportation of broken rock. Dust from blasting cannot be eliminated, but it can be controlled by means of increased ventilation, the use of water sprays, and the control of blasting hours. Dust from ore movement can be reduced by keeping the broken rock in a moist condition at all times. The dust from the rock drilling operation has been found to be the most difficult to control. Concentrations of dust caused by rock drills in stopes can usually be reduced to the safe minimum of 300 particles per cubic centimeter (p.p.c.c.) by diluting the air with increased ventilation. In development headings, where the machines are more confined, this is not always practicable. Therefore, the dust must be eliminated at its source. This paper deals with the reduction of dust from Leyner machines by adopting improved designs.

Jan 1, 1947

By C. L. Popp

The scope is to address issues confronted by parties in the mining industry such as: Mine planners, survey and engineering departments, field teams and subcontractors. Describing approaches and best practices for assembling a project team to identify and create modeling requirements and to implement beneficial results. 3D Machine Control and Guidance tools continue to reduce project risk and attract quality resources with skill sets new to the earthmoving industry. These tools increase production, reduce rework and help with government permitting.

May 1, 2013

By Z. Q. Liu, J. M. Du

"On the basis of analyzing current design and applications, the structure form, working loads and design principles of shaft sinking headframe are summarized in this paper. To overcome the insufficient bearing capacity and geometry size of the finalized shaft sinking headframe in China, a series of new large shaft sinking headframe were developed under vertical shaft construction conditions of maximum net diameter of 12.0 m and maximum depth of 1200 m. The new series shaft sinking headframe include two sets (with single sheave platform and double sheave platform), three dimensions (optimum shaft diameter <8.0 m, 8.0-10.0 m, and 10.0-12.0 m, respectively) for each set, and has innovation and optimization on structure of the sheave wheel platform (MU type) and bracing frame (REN and ZHONG type). The largest new shaft sinking headframe can arrange up to 4 hoisting equipment simultaneously and has bearing capacity more than 10000 kN. Two of the new shaft sinking headframe were successfully applied in practical engineering, such as the Hulusu auxiliary shaft, the Dahaize 1# auxiliary shaftand Sishanling auxiliary shaft. These applications showed that the new shaft sinking headframe has sufficient bearing capacity and reliable applicability. The new shaft sinking headframe could provide an effective guarantee for safety and efficiency sinking of deep-large shaft in the future.INTRODUCTIONShaft sinking headframe is one of the basic shaft sinking structures and it is mainly for hanging hoisting containers and sinking facilities in sinking a vertical shaft (Yu & Shi, 1991; Wang, Jing, & Liu, 2007). Currently, 7 types of steel pipe sinking headframe are used in China, which are mainly finalized by the Ministry of Coal Industry of China (Wang, 1988). As shown in Table 1, V-type is the largest of them and it is only suitable for sinking shaft of diameter less than 8 m and depth less than 1 000 m(Yang, 1982). However, with the increase of mining depth and scale of mineral resources in China, the diameter and depth of newly built vertical shaft are increasing continuously (Xie, Zhou, Xue, Wang, Zhang, & Gao, 2012; Qi & Pu, 2013). At present, the maximum net diameter of vertical shaft is close to 12 m, and the maximum depth is more than 1600 m (Yang & Chen, 2015; Xu, Yang, Liu, & Qin, 2015). The shaft sinking headframe has become the main restrictive factor for the development of sinking equipment, such as the height of muck discharging platform cannot meet the usage requirement of hydraulic umbrella driller, the size of sheave wheel platform is difficult to arrange the increasing hoisting and suspension equipment, the bearing capacity is insufficient to meet the needs of multiple hoisting loads in sinking a deep-large shaft, etc. Therefore, development of new shaft sinking headframe for deep-large shaft (>1000 m in depth and 8~12 m in diameter) is urgently required for China and also the whole world."

Jan 1, 2019

By J. K. Shaw

The science of low temperature engineering is well entrenched in mining. Uses for common cryogens, including liquid oxygen (LOX), liquid nitrogen (LN2), and liquefied natural gas (LNG) in the gas and minerals industries are reviewed. Potential future applications are discussed within the scope of mining, particularly in refrigeration and ventilation. The second part of this paper focuses on the Linde cycle, which is at the heart of most liquefaction plants. Steady state equations describing the mass and energy flows are presented. The paper concludes by explaining the concept of a wind powered Linde- Hampson cryogenic cycle and assessing, with scoping calculations, the technological feasibility of producing cryogens with an intermittent source of (renewable) energy.

Aug 1, 2013

By C. C. Li

Traditionally, strong and stiff devices, such as fully encapsulated rebar bolts and concrete lining and arches, are preferred for underground rock support. The attention is paid to the strength of the devices in such support designs. It has been observed in engineering practice that support systems composed of stiff devices are often subjected to premature failure in high stress rock conditions. In the past decade, yield support devices have been employed to improve the performance of rock support systems. A rock support system usually consists of both internal and external devices that are installed within the rock mass and on the free surface of the rock, respectively. Great efforts have been made to make support devices yieldable in the past years, but the efforts are focused on different aspects in the tunneling and mining branches. In the tunneling branch, the focus has been put on the development of external yield devices, such as Lining Stress Controller (LSC), Honeycomb element and compressible concrete, which are embedded in shotcrete liners, while in the mining industry the efforts has been on the development of yield rockbolts, such as the cone bolt and the D-Bolt. The internal and external support devices are not compatible in their deformation capacities in the current rock support systems even though yield devices have been employed. All the devices in a support system should be deformable and compatible in deformation capacity. With such a support system, premature failure of individual support devices could be avoided and the service life of the support system is prolonged. It is a trend at present to take into account the energy absorption capacity, instead of simply the strength, of support devices in rock support design.

Jan 1, 2015

By L. Dubourg, H. Habibi, D. Rasmussen

The combination of laser welding with Gas Metal Arc Welding (GMA W) forms the hybrid laser-OMA W welding. This process is an attractive tool with a high potential in welding lightweight structures, especially for aluminum alloys. For five years, this technology has increasingly attracted interest in both, industry (aeronautics, automobile, metal industries producing large structures) and academia (universities and research centers). Hybrid laser-OMA W welding process is generally accepted for its robustness, efficiency and flexibility. Coupling of a deep-penetrating laser beam with the heat and molten metal feeding of GMA W significantly expands the original welding application range of lasers. Its main advantages compared to the two individual components are deep and stable weld penetration, gap-bridging ability improvement, low distortion and easy filler metal addition. Hybrid welding allows a much wider groove tolerance compared to laser welding, especially for aluminum welding. Moreover, the reduction in distortion decreases the post-welding rectification needed and makes the assembly easier. In addition, if metallurgical factors are critical, the weld composition can be balanced with filler metal, decreasing the hot cracking susceptibility of some aluminum alloys. The combination of these two welding processes can also improve the weld bead shape quality (including the elimination of undercut), possibly reduce the porosity and increase the welding speed. This article reviews the recent works about the laser-OMA W hybrid welding of aluminum alloys. After a brief presentation on the interaction mechanisms between a laser beam and an electric arc, the paper depicts the typical welding parameters and experimental methods along with their characteristics.

Jan 1, 2006

By M. Sengupta

International trade in minerals plays a very important role in the economic growth of many nations. Several less developed countries a1•e heavily dependent on their mineral exports for earning foreign exchange, which is needed for industrialization. Mineral exporting nations experience many problems in international mineral markets; the most important are tariff barriers, deteriorating terms of trade, instability in metal prices, etc. The formation of international mineral cartels to raise prices can be successful only to a limited extent and only for a short period of time.

Jan 1, 1976

By Roger Potvin

Abstract The demand for pure zirconium and titanium metals in Germany increased considerably during the war. Pure zirconium was used in flash bulbs, in vacuum tubes, and in time fuses for bombs, where it has a decided advantage because it gives no gas in burning. Under the form of alloy, it was used with other rare elements for making substitutes for platinum; it was also used as a scavenging agent in high-grade steels. Metallic titanium was mainly used in connection with the manufacturing of special alloys. The authors were sent to Germany by the Department of Reconstruction and have investigated the German process developed for producing these rare metals. They describe the procedure and special equipment used for their commercial production in Germany during the war. General Metallic zirconium and titanium were .produced on a commercial scale in Germany by the thermal reduction, with metallic sodium, of potassium fluozirconate and titanium chloride, respectively, using a mixed potassium and sodium chloride flux. According to the information gathered, the sole German producer of these rare metals in pure form was the Deutsche Gold und Silber Scheideanstalt (commonly called Degussa), at their Werk II, 215 Gutleutstrasse, Frankfurt/Main, which was visited by the authors on September 18th, 1945. As far back as 1934, Degussa was carrying on active research on the manufacture of zirconium, and nearly one ton of the pure metal had been produced before September, 1939. Concurrently, a quite similar process was worked out for the recovery of titanium and it was in commercial operation in the year 1938, during which the production totalled about half a ton (metric). The demand, especially for pure zirconium, increased considerably during the war, attaining a total of about 48 tons during the period October, 1939, to the end of 1944, and reaching a peak of more than 15 tons in 1943. In 1944, the plant was slowed down due to the frequent and disastrous bombing by the Allies, especially in March and September.

Jan 1, 1946

By Ifeanyichukwu Nweke

"Aluminium rolling processing from ingots to cold rolled coils comes with a lot of challenges especially in controlling defective products in casting, hot mill and cold mill operations. Hence this study focused on reducing defects at mills and cast-house using six sigma approaches. The use of six sigma approach will help the production experts to determine the gap between its operation and world class process. Practical data from First Aluminium Rolling mills were presented and analysed and mini improvement projects were proposed based on organisation need to achieve excellence. This study encourages aluminium alloy industries to pursue process improvement projects on the basis of analysis on data obtained from their shop floor, hence ensuring that through this, recovery is improved and cost of poor quality is reduced.INTRODUCTION Engineer Bill Smith while working at Motorola in 1986 introduced a new concept in which a set of techniques and tools are used for process improvement by controlling variations (defects). These tools and techniques are explained by an acronym DMAIC. D DEFINE the problem M MEASURE the variables in the problem A ANALYSE the variables of the problem I IMPLEMENT and verify the solution to the problem C CONTROL the solution to sustain it Most times in six-sigma approach, variations in the process that results in defects and customers’ dissatisfaction are targeted at 3.4 defects per million opportunities. There are numerous methods six sigma application use to achieve quality results and innovative strategies. Improving the quality of process through these methods helps identify and reduce variations which paves way for organisational excellence. In this study, it is encouraged to use six sigma techniques to improve aluminium rolling operations and other aluminium processing activities, the benefits of such improvement concept include: • Satisfy the voice of the customer (VOC) • Minimise costs • Maximise Profits • Build Good Team • Implement Profitable Project"

Jan 1, 2018