Search Documents

By G. V. Fernandez

Sociedad Minera Cerro Verde S.A.A leaches secondary copper sulfides. In recent years, the mine has introduced innovations that have improved the management of mineral crushing, agglomeration, curing, and leaching. The crushing plant, for example, uses the concepts of degree of balance and percentage of time in an operationally balanced state which, displayed in real time, facilitate more intensive and uniform utilization of the crushers. High agglomerate quality is ensured with the correct dose of moisture, which is adjusted to the changing characteristics of the mineral through the use of electrical conductivity measurements. The amount of acid used for curing the agglomerate is also adjusted by using quality control information. Finally, the stockpile irrigation regime is managed using the criteria established by the "Lixiviant Request Rate", which optimizes the addition of leaching solution, creating such benefits as faster recovery, and reduced acid and energy consumption.

Jan 1, 2007

By A. V. Lyamin, J. P. Wang, A. J. Li, Z. Qian

"For general stability analysis of rock slopes, rock mass strength and rock mass disturbance are definitely should be considered. In addition, the impact of earthquakes must be taken into account. In fact, the rock mass strength is very difficult to be assessed which causes the difficulty of analysing rock slope stability. Therefore, an empirical failure criterion, the Hoek-Brown failure criterion, has been proposed. It is one of the most widely accepted approaches to estimate rock mass strength. The rock mass disturbance is important and was found having significant influence on evaluating rock slope stability, especially for rock slope with poor quality rock mass. In the Hoek-Brown failure criterion, the disturbance factor can represent the level of the rock mass disturbance which would provide a reasonable basis for estimating rock mass strength.This research will not only discuss the slope factor of safety, but also consider the influence of the seismic force on rock slope stability assessment using pseudo-static method. In practice, only horizontal seismic coefficient is used. Various magnitudes of the disturbance factor and recommended blasting damage zone thickness are also taken into account. The blasting damage zone thickness considered ranges from 0.5 to 2.5 times of slope height. The research results have potential to be extended and then sets of comprehensive stability charts can be provided for the rock slope stability evaluations. They will be convenient tools for practising engineers. In this study, finite element upper bound and lower bound limit analysis methods are employed. Their applicability has been investigated in some previous studies. The differences between upper bound and lower bound solutions are less than ±10% which would provide reasonable and acceptable range for rock slope stability safety factor estimation."

Jan 1, 2015

By Andrew Barnes

The adsorption capacity of peat collected from a proposed mine development in northern Sweden has been determined using laboratory column experiments in which peat was irrigated with a simulated (acidic) waste rock dump leachate. The simulated leachate was made using a hydrogen peroxide leach of composite waste rock from the proposed mine development. The waste rock samples were composited in proportion to their predicted extractable tonnage for the mine development in order to generate a more representative leachate solution for the waste rock facility. As expected the test revealed that the peat material shows a very high affinity for attenuation with greater than 70% of Co, 90% of Ni and 95% of Cu removed from influent solutions through the majority of the tests demonstrating the potential benefits in mine water treatment. In contrast, it was found that Fe is initially released from the peat at concentrations up to 100 mg/L and can mean potential problems for the water released depending on the receiving environment. The exact mechanisms for Fe release is uncertain, though it is suspected that ion exchange / competitive desorption is responsible. Inspection of the laboratory results and drainage data from the natural peat wetland receiving drainage during overburden prestriping and mine development at the mine site are comparable, confirm the validity of the experiments, and further emphasize the potential for future use of pre-stripped peat material in managing water quality.

Aug 1, 2013

By R. Carter, C. S. Samis

"SummaryThe results of this investigation indicate that the gold in the cyanide tailing of refractory gold cyanides is occluded in fused •particles formed during roasting. This conclusion was reached following microscopic examination of calcines produced at various furnace temperatures with different atmospheres, and a •comparison with calcines produced by decomposing samples of completely sulphated concentrate under conditions such that the maximum particle temperature varied between 6•50°C. and 1,100°C. This comparison showed that the particle temperature during a normal roast may be several hundred degrees higher than the furnace atmosphere, or that the fusion is associated with a low melting (950°C.) eutectic mixture of FeO and FeS.Because of the unavoidable particle fusion during a furnace roast, and because low particle temperatures are essential for gold extraction by cyanidation, aqueous medium oxidation under high oxygen pressures was studied. Gold recovery from calcines produced by this means was over 98 •per cent •compared with a maximum of 80 per cent from furnace calcines.IntroductionMANY arsenical gold ores are called 'refractory' because much ' of the gold cannot be satisfactorily extracted by cyaniding the raw ore or concentrate. Even when such ores are roasted to oxidize .the iron and arsenic and 'release' the gold, often 10 to 25 per cent of the gold present is lost in the cyanide residues."

Jan 1, 1952

By Eurípides do Amaral Vargas Jr., J. A. de Mello Franco

"It is frequently necessary to excavate a tunnel for Civil Engineering purposes, or wells for petroleum exploitation, in laminated rock mass like schists or phyllites or in highly foliated gneisses. The determination of the pre-existing in situ stresses is essential, in order to assure the stability of these excavations. In most cases, the pre-existing triaxial stress field is arbitrary in relation to the tunnel or well axis. For these rock masses the concept of Generalised Plane Strain can be correctly utilized.There are closed form solutions for the calculation of stresses in anisotropic rock masses under Generalised Plane Strain conditions (Lehknitskii, 1981 and Hong , 1994). Based on these analytical solutions, established for the cases of Generalised Plane Strain, a synthetic problem will be formulated: the theoretical in situ stress tensor acting on this rock mass will be determined, with the aid of Bayesian Inverse Problem Techniques, as developed by de Mello Franco (2009). Additionally, the reliability of results obtained will be evaluated, in accordance with the research performed by this author. INTRODUCTIONThe Inverse Problem Technique, as developed in the paper, is based on the definitions and concepts obtained from the current literature and used for the solution of Inverse Problems, but the innovation to be presented is the utilisation of Bayesian Techniques and the determination of the reliability of the results obtained. This will be shown in a synthetic example where the determination of the in situ stress tensor, from strain measurements in a drill hole is supposedly performed. It is assumed that this drill has its axis arbitrarily placed in relation to the rock mass. Generalised Plane Strain conditions will hold for use with problem. The equations of Beltrami – Mitchel, in agreement to Lekhnitskii (1981) and Ong (1994), will be used in this synthetic case, for calculating strains, hypothetically measured in the hole before the final excavations. Finally a synthetic example for the determination of the in situ stress in a fully anisotropic rock mass, based on Bayesian Techniques and its reliability, developed in de Mello Franco (2009) is presented."

Jan 1, 2015

By Oleg G. Tovmachenko

We have studied optical properties of fluorescent nanoparticles. These particles consist of a metal (gold/silver) core, an empty and a dye labelled silica shells. The different dye molecules with moderate quantum yields (about 0.3) has been used. Almost all of types of nanoparticles show fluorescence enhancement. This enhancement is strongly dependent on the degree of the overlap between the surface plasmon band of the metal and the absorption/emission band of the dye molecules. The results are interpreted in terms of competition between local field enhancement and quenching of fluorescence by the metal surface.

Oct 1, 2003

By A. J. Macdonald

Gold deposits hosted by banded iron formation (BIF) in Ontario exhibit a marked association with localized zones of deformed and hydrothermally altered BI:F . Secondary sulphides and carbonates are conspicuous. Proposed carbonate-facies IF , or exhali tes, such as green carbonate in the Larder Lake camp and ankerite veins in the Porcupine Camp are structurally controlled, hydrothermally deposited zones of carbonate replacement and fissure filling. Gold precipitation from hyd r othermal fluids in strain-generated conduits may be due to (a) plating upon secondary sulphides, (b) pH change due to carbonatization of BIF or (c) destabilization of gold in solution due to sulphidation of BIF .

Jan 1, 1984

By John Plecash

This paper comprises a general outline of all of the developments, including the history, geology, mining, milling, power and transportation installations, at the gold mining operation of La Luz Mines Limited and the copper mining operation of its wholly-owned subsidiary, Rosita Mines Limited, both located in north-central Nicaragua. The low-grade, gold-bearing ore-bodies of La Luz Mines, contained in highly fractured and folded Lower Cretaceous sedimentary rocks, were from 1909 to 1928, mined and treated by primitive methods by the La Luz and Los Angeles Mining Company. The abandoned property was acquired by La Luz Mines Limited in 1936, and was equipped with modern machinery and put into production in 1939. Between 1939 and 1948, the daily rate of production was in-creased from 300 tons per day to 2,-000 ton per day. The ore reserves available for open-pit mining were depleted in 1954. Since then, the entire production has come from under-ground operations.

Jan 1, 1963

By T. Avilez, D. Salari

"The economics of developing gold deposits containing elevated levels of cyanide soluble base metals is often challenged by high cyanide consumption and increased operating costs. SART is a chemical process that enables cyanide consumed by base metals to be recovered and recycled for gold leaching. The process also provides concurrent recovery of the base metal to generate incremental revenue from the sale of high-grade base metal sulphide concentrates. Although SART was developed and successfully piloted by Lakefield Research and Teck Corporation in the late 90’s and is now a public domain technology, the adoption of SART has been relatively slow due to concerns about implementation costs and the reliability of metallurgical performance. Through extensive experience in selective metal sulphide precipitation applied to mining wastewater since 2007, BQE Water has provided process know-how, design along with operations and maintenance experience to a number of projects involving the integration of SART into various metallurgical flowsheets on an industrial scale. This paper presents the commissioning experience and operating data from a SART plant treating up to 500 m3/hr of leach solution at a heap leach operation in Mexico. INTRODUCTION One of the current trends in the gold industry globally is the increasing importance of complex polymetallic gold deposits as discoveries of large Carlin type gold deposits become increasingly rare (Sceresini, 2005). The presence of cyanide soluble copper and zinc in complex gold deposits necessitates changes to the traditional gold extraction metallurgical flowsheet. A tool available to the industry to help manage the interference of cyanide-soluble base metals in gold extraction is the SART (sulphidization-acidification-recycling-thickening) process. SART breaks the weak acid dissociable (WAD) base metal-cyanide complexes, precipitates the metals as high-grade sulphide concentrates and makes the freed cyanide available for recycle."

Jan 1, 2018

By Etienne Roy Grégoire

Since the early 1990s, the Canadian mining industry has been increasingly defined by the signing of Impact and Benefit Agreements (IBAs) between mining companies and Aboriginal peoples. While these agreements are intended to complement the legal system, they also serve to establish the legitimacy of mining projects and to encourage the harmonious integration of these projects into their social and environmental contexts. Beyond their practical implications, what are the effects of such agreements on the ability of Aboriginal communities to access the institutional space where the authorization of mining projects and the conditions of their implementation are decided? Can we view IBAs as a preliminary step towards the operationalization of the principle of Free, Prior and Informed Consent? This paper aims to explore the potential of IBAs as a sustainable solution to the legitimacy issues that result from the implementation of the formal regulatory framework governing mining activities in this jurisdiction. We highlight what constraints and opportunities the James Bay and Northern Quebec Agreement (JBNQA) engenders for local communities and draw attention to the ways in which the negotiation of the Raglan IBA and the environmental evaluation processes act upon each other. We find that certain structural problems - and problems of legitimacy ? related to mining in Northern Quebec cannot be solved by the sole signature of an IBA, which suggests the need for caution when considering such agreements as a panacea. The Raglan case demonstrates that IBAs, like other modes of regulation relying on the direct interface between companies and communities, would benefit from a stricter framework and more explicit ties with official regulation channels.

Aug 1, 2013

By J. D. Zhu

A numerical model for predicting microporosity formation in aluminum castings has been developed, which describes the redistribution of hydrogen between solid and liquid phases, the transport of hydrogen in liquid by diffusion and Darcy flow in the mushy zone, One of the key features of the model is that it uses a two-stage approach for porosity prediction, In the first stage, the volume fraction of porosity is calculated based on the reduced pressure, whereas, in the second stage, at fractions solid greater than the liquid encapsulation point, the fraction porosity is calculated based on the volume of liquid trapped within the continuous solid network, which is estimated using a correlation based on the Niyama parameter, The porosity model uses thermal data calculated using the commercial finite element package ABAQUSTM. The model has been applied to examine the evolution of porosity in a series of experimental samples cast using unmodified A356 in which the initial hydrogen content was varied from 0,048 to 0.137 [cc/100g], A comparison between the model predictions and the experimental measurements indicates good agreement in terms of the variation in porosity with distance from the chill and the variation resulting from initial hydrogen content.

Jan 1, 2005

By A. Grimod

Rockfall drapery systems are commonly used as a simple, fast and cheap measure against the rock falling trajectories affecting very steep slopes. The system basically consists of a steel mesh, which is held on the top edge with a longitudinal cable fixed by means of a suitable number of anchors. The effect of this kind of intervention is to control the falls of the rocks, which are driven toward the bottom with slow velocity, or are stabilized on place. It can be used on any kind of slope to protect sensitive target in the mining industry, roads and railways, and inhabited areas. The falling blocks, typically smaller than 0.6 - 1.0 m in diameter, pile up into a trench (or into a ?pocket of mesh?) at the bottom. In comparison to other types of rockfall interventions, the simple drapery is cheaper, and its maintenance is easier, but on the other hand it cannot be considered the remedy for shallow instabilities, because it can only mitigate the effect of the falling trajectories. The design of simple draperies requires the analysis of several factors like the slope features (height, gradient, morphology), the geological and dynamic features (nature of the ground or rock, type of instability, erosion problem, blocks size), the environmental condition (presence of vegetation, aesthetical problem), the installation problem (accesses to the slope, safety for the workers, safety for the surrounding areas) and finally the performance required (temporary or permanent intervention, required maintenance, cost). Finally the most problematic design-step is the choice of the suitable mesh, the top longitudinal cable, and the top anchors type. Because of the highly variable nature of rockfall behaviour these structures cannot be standardized, but they have to be analyzed and designed for each case. Maccaferri has developed a new software application (MacRO 2) has a practical tool to define the mesh and the related supporting structure composed by up-slope cable and anchors. The software, based on the approach proposed by Muhunthan B. et al. (2005), allows designers to verify the top longitudinal cable, the anchors, and the mesh drapery, and to plan for maintenance procedures. Even if the method seems quite simple and rough, it is effective and lets the designer correctly foresee the materials and the geometrical features to be used on the interventions. This paper analyses the condition for the simple drapery installation, the main steps for the calculations, and it will present a case study in a U.S. mine. Nevertheless, even if the software allows a quick and simple calculation approach, onsite observations are always recommended in order to achieve a good design, with the ultimate goal of protecting property and human lives.

Aug 1, 2013

By R. Pandher, R. Schonewille, N. Tripathi

Advanced process modelling tools were developed for the Xstrata Nickel Sudbury Smelter flow sheet using a combination of FACTSAGE TM METSIMTM and ARENATM software. These tools were employed to assist with plant optimisation, emission control, process design, troubleshooting and case studies as applied to the smelter. The development of process modelling tools in pyro-metallurgy commonly involves an in-depth study of the therm o-chemical properties (heat capacity, liquidus temperature, etc.) of all high temperature phases, usually matte and slag. The preferred tool for this purpose is FACTSAGETM, a well-known then-no-chemical modelling software package. The results from the therm o-chemical model have been subsequently incorporated into the development of a process model for the entire smelting facility using the METSIMTM platform. Such process model also includes a number of special features adopted to effectively simulate the complex industrial phases; matte and slag systems. To ensure the robustness and reliability of the process model, several process parameters and assumptions were verified with laboratory and plant data. Consequently, the model includes the ability to examine the impact of a number of plant parameters on potential plant performance. Primary variables are the percent sulphur elimination during concentrate roasting, furnace matte grade and degree of matte metallization. Key output parameters include operating temperature, furnace coke requirement, sulphuric acid production, CO2 emissions and overall energy requirements. Selected outputs from the process model (for example blowing time, slag production rate and matte converting rate) can then be utilised in the development of a discrete event model (DEM) for the smelter using ARENATM software. Incorporation of reliable and validated mass balance parameters enhances the robustness and reliability of the DEM model. The integration of then-no-chemical, process and DEM modeling tools has a distinct advantage in planning plant trials and examining process design initiatives at Xstrata Nickel's Sudbury Smelter. The present paper discusses the development of these three models and the synergies existing among them. Typical results from all three models are also presented.

Jan 1, 2011

By R. Pandher, R. Schonewille

Advanced process modelling tools were developed for the Xstrata Nickel Sudbury Smelter flow sheet using a combination of FACTSAGETH METSIMTM and ARENATM software. These tools were employed to assist with plant optimisation, emission control, process design, troubleshooting and case studies as applied to the smelter. The development of process modelling tools in pyro-metallurgy commonly involves an in-depth study of the therm o-chemical properties (heat capacity, liquidus temperature, etc.) of all high temperature phases, usually matte and slag. The preferred tool for this purpose is FACTSAGETM, a well-known then-no-chemical modelling software package. The results from the therm o-chemical model have been subsequently incorporated into the development of a process model for the entire smelting facility using the METSIMTM platform. Such process model also includes a number of special features adopted to effectively simulate the complex industrial phases; matte and slag systems. To ensure the robustness and reliability of the process model, several process parameters and assumptions were verified with laboratory and plant data. Consequently, the model includes the ability to examine the impact of a number of plant parameters on potential plant performance. Primary variables are the percent sulphur elimination during concentrate roasting, furnace matte grade and degree of matte metallization. Key output parameters include operating temperature, furnace coke requirement, sulphuric acid production, CO2 emissions and overall energy requirements. Selected outputs from the process model (for example blowing time, slag production rate and matte converting rate) can then be utilised in the development of a discrete event model (DEM) for the smelter using ARENATM software. Incorporation of reliable and validated mass balance parameters enhances the robustness and reliability of the DEM model. The integration of then-no-chemical, process and DEM modeling tools has a distinct advantage in planning plant trials and examining process design initiatives at Xstrata Nickel's Sudbury Smelter. The present paper discusses the development of these three models and the synergies existing among them. Typical results from all three models are also presented.

Jan 1, 2011

By M. Souley, G. Armand, M. Ghoreychi, D. Seyedi, J. -B. Kazmierczak

"An anisotropic constitutive model is proposed in this paper accounting for both structural anisotropy and induced anisotropic plasticity. It is assumed that the rock is composed of a matrix and of potential planes of weakness. The matrix is assumed to be linear, transversely isotropic and the plasticity is described by a non linear yield function where the parameters are deduced from the nonlinear Hoek-Brown envelopes in pre- and post-peak, and derived from the laboratory characterization. A non-associated flow rule is used with a distinction between compression and extensional stress paths, as well as the absence of volumetric strain beyond large plastic distortion.The planes of weakness are considered as known a priori or assumed to be oriented perpendicular to the direction of the current minor principal stress. An elastic-perfectly plastic behavior according to the Mohr-Coulomb criterion is assumed in the planes of weakness; while the elastic part is considered as linear and transversely isotropic.Finally, the proposed model was implemented in FLAC3D and used to simulate triaxial compressions to provide a verification of the implementation. The applicability of the implemented model to reproduce damage (pre-peak) and/or failure developments around a circular opening is checked. The GCS drift, one of the mine-by experiments set up at the main level of the Meuse/Haute-Marne Underground Research Laboratory, is selected for this first application."

Jan 1, 2015

By George Wilkinson

"AbstractThe consistent relationship between the availability of electrical energy and our economic wellbeing is well known. As we develop the energy we need to nurture industrial civilization in decades ahead, we will at the same time reduce our reliance on dwindling supplies of oil and gas. Coal and uranium will be developed as our major fuel sources to meet medium-term. energy needs, followed by fusion and solar energy for the long term.IntroductionTHIS PAPER treats the matter of energy in a way that is quite different from that of the crisis-type atmosphere which surrounds so much of it currently in the news media. On the one hand, we lift the whole subject of energy out from its present-day involvement with short-term issues and take an important longer-term look at the solutions which lie before us. On the other hand, we recognize that short-term issues are important and, as we are reading and hearing, many of the right short-term solutions continue to elude our politicians, our policy makers, and even some of those with knowledge and authority in the energy field.A year ago, if you asked people how they would go about conserving energy, they would probably have said turn out the lights. They would probably say the same thing today, but they might also include other things such as driving the automobile more slowly or putting more insulation in the attic. However, their first impulse is still to use less electricity."

Jan 1, 1977

By A. Gronningsater

Introduction As is well known, the fight between the blast furnace and the reverberatory furnace in copper smelting during the second decade of the century ended with a victory for the latter, a result which must largely be attributed to the introduction of flotation methods. To my knowledge, no new blast furnace has been blown-in at any American copper smelter since the War. As the metallurgy of nickel, up to and including matte smelting, is generally considered a close parallel to that of copper, the introduction of reverberatory smelting in the big new smelter of the International Nickel Company at Copper Cliff, built in 1928-30, seemed a logical adherence to a well established trend. In view of these facts, considerable comment was made when Falconbridge Nickel Mines decided to retain the blast furnace in their smelter built about the same time, in 1929. A presentation of the reasons governing this choice should therefore be of interest. The basic principles underlying the Falconbridge practice, and the considerations guiding the successive steps in the operations, will be discussed in the following. To understand the problems involved, the character and mode of occurrence of Sudbury ore must be kept in mind. Large amounts of disseminated ore are generally present. Although the gangue usually runs only about 50 per cent Si02, the ore hoisted as a rule contains more silica than needed in the smelting operation; until recently this excess was removed entirely by hand picking (in later years supplemented by magnetic sorting methods), a difficult and not very satisfactory method, in which 'the border line between ore and waste is entirely arbitrary, and therefore too much depends on the judgment of the picker.

Jan 1, 1934

By Douglas H. Brown

Cadmium and other 'minor' metals in Canada tend to remain inconspicuous given the prominence of the country's massive production of other minerals. This same reality is reflected in the accuracy and deficiency of quantitative data concerning the sources of supply and demand for these metals. It is the intent of this paper to identify the nature of some of these difficulties and to reconstruct a more accurate description of Canada's production and consumption of cadmium, based on the results of recent surveys undertaken by the Mineral Policy Sector of Energy, Mines and Resources Canada and Noranda Sales Corporation Ltd.

Jan 1, 1978

By H. Bouzahzah

Sulfidic tailings, subjected to atmospheric water and oxygen action, can generate acid mine drainage (AMD); which is the most important environmental problem facing the mining industry. AMD generating potential can be assessed by the static tests which consist of a screening method where the neutralization potential (NP) and the acid-generating potential (AP) of a given rock sample are determined. The AP and NP are determined separately in the different static test existing procedures which can be divided into two distinct classes: chemical and the mineralogical methods. For some chemical method, the AP is calculated on the basis of total sulfide sulfur content in the sample which may overestimate its AP if significant quantities of non-sulfide sulfur species are present (e.g. organic S in coals, some sulfate as gypsum, barite, etc.). However, the mineralogical method evaluates the AP by the sum of the individual sulfides participation on acid generation based on their concentration within the sample and can be more accurate than the chemical method. For AP calculation, the Paktunc (1999a) mineralogical static test takes into consideration all sulfide minerals occurring in the sample. However, it does not take into account the rates of acidity production of these sulfides submitted to weathering conditions. So, the present study focusses on the modification of Paktunc AP calculation by considering the acidity production rates of these minerals. To reach this objective, five base-metal sulfides (pyrite as reference, chalcopyrite, sphalerite, arsenopyrite, galena), diluted within quartz (25?75 wt.%) simulating mill tailings were subjected to a kinetic test to evaluate their AP. The results show that all the studied sulfides minerals generate acidity at different rates, so the Paktunc?s equation for AP calculation has been adapted accordingly.

Aug 1, 2013

By K. R. Barnard, K. D. Marte, T. V. Gamarano

"The first commercial scale application of CSIRO’s direct solvent extraction (DSX) technology has been in operation at the Boleo project in Mexico since December, 2015. In this application, DSX is a synergistic solvent extraction system consisting of the extractants LIX 63 and Versatic 10 for recovery of cobalt and zinc from a solution background of manganese, magnesium, and calcium. Key operating parameters such as metal extraction, phase disengagement and extractant stability are summarized and discussed in this paper.INTRODUCTION Commissioning of the Boleo processing plant, located on Mexico’s Baja peninsula, began with the copper circuit starting in late 2014, with first copper cathode production achieved in January, 2015. The cobalt and zinc circuits began commissioning in December, 2015 with first zinc sulphate monohydrate (ZSM) and cobalt cathode production achieved in February and April, 2016 respectively. The Boleo project flow sheet and development has been described in detail in previous publications (Dreisinger, et al. 2005; Dreisinger, Baxter, & Molnar, 2006; Dreisinger, et al. 2008; Dreisinger, et al. 2009) and is summarized schematically in Figure 1. Boleo is a mixed oxide/sulphide Cu-Co-Zn-Mn high clay deposit that is processed in a whole ore, atmospheric, oxidative and reductive, sulphuric acid/seawater leach. Copper is recovered as cathode by conventional solvent extraction and electrowinning. Cobalt and zinc are recovered, from a solution background of manganese, magnesium, and calcium, by CSIRO’s synergistic solvent extraction technology Direct Solvent Extraction (DSX). Cobalt and zinc are bulk stripped from the DSX circuit and then further purified by phosphinic acid solvent extraction to produce zinc sulphate monohydrate granules via spray dried granulation and cobalt cathode rounds via divided cell electrowinning."

Jan 1, 2017