Search Documents

By L. Cifuentes

The temperature dependence of: a) electrolyte density, viscosity and electrical conductivity and b) the equilibrium constants of formation for all relevant species have been determined as part of an effort to model the operation of a copper electrowinning cell based on reactive electrodialysis. The studied ranges were: 1.01 to 1.25 g/cm3 for density, 4.9x10-4 to 16.4x10-4 kg m-1 s-1 for viscosity and 0.02 to 86.0 Sri m-1 for electrical conductivity. Density and the electrical conductivity of the catholyte increased linearly with temperature whereas the viscosity increase was exponential. The main effect of ionic speciation was to decrease the electrical conductivity with increasing metal concentration due to ion association (mainly the formation of bisulphate ion) which lowered the concentration of protons (the most mobile species) in solution. This effect was specially noticeable in the anolyte. Mathematical relationships with correlation coefficients between 0.959 and 1.000 have been found for all the studied variables.

Jan 1, 2007

By G. Dubé, A. Leclerc, P. Quinn, G. E. Agar, J. Y. Clouthiér, J. D. McLaughlin

"Gold dissolution by cyanide requires the presence of oxygen which is usually supplied by sparging compressed air into the gold containing slurry. For those ores that contain certain obnoxious substances that consume oxygen, maintaining the required minimum level of dissolved oxygen can be troublesome. One of the most economical solutions to the problem of low dissolved oxygen, especially in plants that have air compressors installed, is to enhance the rate of oxygen mass transfer.The oxygen mass transfer rate was measured in a two phase system using two different sparger arrangements, and with addition of a frother that is known to reduce the bubble size produced by the sparger. The common sparger system was shown to be inefficient compared to a readily available but under utilized method of gas dispersion which introduces air directly below the reactor turbine. Transfer of this technology to an operating plant confirmed the beneficial effect of the improved sparger system. The addition of the frother did decrease the bubble size, but it also reduced the oxygen mass transfer rate."

Jan 1, 1993

By Cris Sideco

This paper describes the concentration processes of the Sullivan. Concentrator, including crushing , transportation, sink-float, grinding , flotation and dewatering. Handling of hot muck has had a deleterious effect on most of the processes, resulting in significant operating problems and poorer metallurgy. These problems are described -in detail. THE SULLIVAN CONCENTRATOR is situated in Kimberley, high up in the Purcell Range of the Selkirk Mountains, at an elevation of 3,600 feet, approximately 4 miles from the Sullivan Mine (see Fig. 1). The original plant went on stream on August 23, 1923 at a designed capacity of 2,500 tons per day. This has been increased in stages to its present rated capacity of 11,000 tons per day. The latest stage was in 1949, when several major projects, including the underground crushing plant, the sink-float plant and the installation of a rod mill, were completed. Some 112,800,000 tons of ore have been treated in this concentrator to November 1975. The plant started on a 48-hour/ week schedule, but was reduced to 44 hours/week in October 1946 and down to 40 hours/week by the end of 1949. Except for a 6-month period in 1952 when the mill operated continuously, the 40-hour/week, Monday to Friday schedule was in effect.

Jan 1, 1977

By R. C. Rowe

THIS paper is an endeavour to analyse the ideal and practical functions of government technical mining services, and their relationship to the National Domain, as well as to one another. its spirit is not critical, even though at times it may appear to besoin fact. It is a serious effort to divert a trend in public thought which delights in calling itself practical whereas it is really merely short-sighted. The author refers particularly to the idea that governmental research is a luxury which should be curtailed in the interests of economy, and turned over to private enterprise or the provinces. In order that we obtain the proper perspective of the question, it is advisable to indulge in a little history. In the year 1842, the Geological Survey of Canada was formed under the guidance of William (later Sir William) Edmund Logan. The literature on the founding and history of the Geological Survey of Canada is extensive, and therefore it is unnecessary to go into detail here regarding it. It might be mentioned, however, that the Geological Survey of Canada is only seven years younger than the Geological Survey of Great Britain (founded in 1835), and is only exceeded in age on the American continent by the State Geological Surveys of New York, Pennsylvania, Massachusetts, and Michigan, which were founded between 1833 and 1836. In 1877, the Geological Survey became a permanent government institution as a branch of the Department of the Interior. It should be noted, however, that the Director of the Survey ranked as a Deputy Minister and reported direct to the Minister. This continued until 1907. In 1886, the Mineral Resources and Statistics Division of the Geological Survey was formed. Some years later, the Canadian Institute of Mining and Metallurgy (then the Canadian Mining Institute), backed by the mining press, began to agitate for the establishment of a Dominion Department of Mines, and in 1907 such a department was founded by the Geology and Mines Act of that year, with a separate Cabinet portfolio for the position of Minister of Mines.

Jan 1, 1939

By T. S. Grewal, S. C. Gupta, H. Natarajan, T. W. McQuade, N. Nejibulloev-Mamedov

Cigar Lake is one of the world’s largest high-grade uranium mines. The ore mined at Cigar Lake is milled at Orano Canada Inc’s (Orano) McClean Lake mill. The average Cigar Lake ore uranium grade since the start of mining activities in 2014 is 17.8% U (range 8– 28%). To achieve budgeted production of 18 M lbs U3O8/yr the required average feed tonnage to the mill is about 45 kt/yr. Arsenic, occurring as arsenides and sulpharsenides, is one of the major elements of concern associated with Cigar Lake ore. The leaching process is a sulphuric acid leach under oxidizing conditions at near atmospheric pressure. The presence of arsenic in the ore consumes oxidant in leaching as well as ferric sulphate in tailings preparation for arsenic sequestration. The average arsenic grade since the start of mining at Cigar Lake is 0.57% As. Further, the ore is hosted in a matrix of sandstone and clay, which results in poor settling in CCD. The average uranium grade for the balance of Cigar Lake Phase 1 ore is expected to drop to 12.5% U and the average arsenic grade is expected to increase to 1.6 % As, with an annual average peak of 2.5%. Therefore the tonnage throughput required to sustainably meet the production target will increase to 55 kt per year. Orano partnered with Hatch Ltd. (Hatch) to perform a gap analysis study to identify key circuits and equipment in the mill that would require debottlenecking. A METSIM mass balance model of the McClean Lake mill was generated and validated with actual mill operating data. Various feed scenarios were then studied, and the outcome was a traffic light table, which highlighted feed scenarios that exceeded installed capacity of major equipment and circuits. The results provided the basis for the PDC for the pre-feasibility study. This paper will outline the results of the gap analysis, the mass balance model, the feed scenarios and the study undertaken to prepare the McClean Lake mill for the change in ore quality from Cigar Lake.

Jan 1, 2020

By Forrest A. Kerr

Introduction During recent years the work of the Geological Survey in northwestern British Columbia has been in the nature of reconnaissance and exploratory mapping, largely for the purpose of gaining knowledge of the potential mineral-producing zones known to occur along the eastern side of the Coast range, and also to gather such data as might facilitate their exploitation. Commencing with fairly detailed mapping in the more accessible parts, the work has been continued and expanded until now an understanding has been gained of the more general features of a continuous section along the range for a distance of about two hundred miles. Geographically, northern British Columbia is more or less isolated. It is cut off from the central part of the Province by a rugged and mountainous country which, except for the telegraph line and a rarely travelled trail along it, is not penetrated by any developed routes or lines of communication. To the west, it is cut off from the Pacific by the Coast range, an extremely rugged area sixty to eighty miles in width which, except along the few navigable rivers cutting across it, cannot be readily traversed. Politically, it is further isolated in this direction by the narrow strip of south-eastern Alaska which borders the coast and extends inland to the axis of the range.

Jan 1, 1931

By S. Kelebek, E. Yalcin

"Diethylenetriamine (DETA) and/or triethylenetetramine (TETA) are reagents that can generally be categorized under ""flotation modifiers"". These polyamines are known to be effective for the deactivation/depression of pyrrhotite that is present in Canadian nickel-copper sulphide ores in large quantities. Recent bench scale testing on some of these complex ores indicated that chalcopyrite flotation can also be adversely affected under certain conditions involving polyamines, which may be taken to be an evidence of their specific affinity towards chalcopyrite. In general, DETA shows no significant depressant action on chalcopyrite while TETA's promotion of hydrophilicity for this mineral has been observed even in the presence of xanthate. This prompted an investigation on thermodynamic equilibria involving these polyamines and copper ions. Results serve a useful purpose to identify conditions for deactivation phenomena. CuDETA2+ and CuTETA2+ chelates as products of sequestration have large predominance areas covering a wide range of redox and pH conditions, where copper xanthate species are not stable, especially in the presence of TETA."

Jan 1, 2009

By Robert Hamilton

Aur Resources is Canada's leading copper mining company with producing mines and development projects in North, Central, and South America. Copper production from Louvicourt Mine in Quebec, Quebrada Blanca, and Andacollo Mines in Chile had a record of 245 million pounds in 2001. Located 600 km North of Montreal, Louvicourt Mine is a joint venture between Aur Resources (30%), Teck Cominco (45%), and Novicourt (45%). Aur Resources is the mine operator with 280 employees working to produce a copper and zinc concentrate. In operation since 1994, the mine has produced a total of 12,606,000 metric tonnes of ore grading 3.6 % Cu, 1.5 % Zn, 26gr./m.t Ag, 0.9gr.m.t Au. This highly mechanized mine reached full production in August 1995 at 4,000 tpd. From 1996 to 2001, the average mine production rate was more than 4,300 tpd. The Louvicourt Mine continued its record of solid performance in 2002 and is expected to continue to do so for the balance of its 2.5 years mine life.

May 1, 2003

By A. G. Darnley

"IntroductionTHE PURPOSE of this paper is twofold. Firstly, to drawn attention to recommendations which have been accepted by the International Atomic Energy Agency concerning radiometric reporting methods and calibration in uranium exploration, and secondly to emphasize the benefits that- will stem from adopting them. These recommendations are contained in an IAEA Technical Report, No. 174, which has been prepared with the intention of serving as a general guide to the subject. The existence of this specialized report is likely to be unknown to most of those who can benefit unless it is given some publicity by an organization such as the CIM. The recommendations were prepared by a small international committee consisting of Dr, P. H. Dodd , U.S .A. , Dr. R. L. Grasty. Canada, Dr. L. Levborg, Denmark, Dr. M. Matolin, Czechoslovakia , Dr. S. D. Simov, Bulgaria, and the writer.The fact that there are standard scientific units of mass, distance and time is taken for granted, It is also accepted that the type of instrumentation used to measure one of these parameters is irrelevant to the way the measurement is reported. Geophysical parameters such as magnetic field strength and gravity have generally accepted units, the gamma and milligal, which are defined in SI terms. These units are employed irrespective of the operating principle, or manufacturer or organization involved in the measurement."

Jan 1, 1977

By M. Mohan Rao

A Sievert ' technique was used. The few determinations made on 10 per cent and 20 per cent V alloys did not show any deviations from Sieverts' law up to I>N2 = 1 atmosphere. The same held true for alloys of 0.2 per cent Ti. Nitrogen absorptions in Fe-Ti alloys, containing from 0.50 to 0.77 per cent Ti at 1,600°C, follow Sieverts' law at low PN2 values, but, due to the formation of a delta titanium nitride phase, deviate from this law beyond critical values of PN2? There is evidence that this phase is Ti1.1N. The behavior observed can be described by the followmg equations: Ti,.,N(o) = 1.7Ti + N K = (fT; ? % Ti)1?7 (f;;.? %~_) = 0.0020 K = fN. %~ = 0.042 '\)-:>N 2 I NTRODUCTJON Nitrogen's solubility in liquid iron-vanadium alloys was investi-gated briefly by Brick and Creevy ( 1), and more extensively by Kash-yap and Parlee (2) and by Pahlke and Elliott (7). Nitrogen's solubility in liquid iron-titanium alloys

Jan 1, 1963

By L. M. Wang, G. P. Jiang, Y. Jiang, Liao. W. S.

ABSTRACT The authors measured porosities and permeabilities for cores from a low-permeability sandstone uranium deposit in Inner Mongolia. Features studied included fine pore structure, mineral composition, cation exchange capacity, granule appearance, and cementing features. In general, grading of the grains was relatively poor, which decreased the radii of the pore channels. The pore throat distribution was significantly heterogeneous. Pore channels ranged from small to large, but the lack of large pore channels led to low permeability. Cementation by calcite and clays, including montmorillonite, chlorite, and kaolinite, resulted in pore channel narrowing, further decreasing the permeability of the formation.

Jan 1, 2014

By Ken McIntyre, Trodel Wolf-Dieter

"Sirius Minerals is a UK based fertilizer development company focused on advancing into operation its polyhalite project in North Yorkshire, England. The operation is known as the Woodsmith Mine which has an estimated 2.7 Billion Tonnes of reserves and is currently in the construction phase. DMC Mining Services was selected to carry out the construction of four shafts for the project, a production shaft of 6.75m diameter to a depth of 1594 m, a ventilation shaft of 6.75 m diameter to a depth of 1565 m, and two additional shafts to support the construction of the material transport system (the MTS and Lockwood Beck intermediate) to 360m in depth for servicing the underground conveyor network for transport of product from the mine site to the costal port facilities located at Teasside. This paper will review the status of the project to date and the innovative approaches that DMC is utilizing to ensure a safe and successful shaft sinking project. INTRODUCTION The Woodsmith Mine in North Yorkshire is a Sirius Minerals-owned deep potash and polyhalite mine located near to the hamlet of Sneatonthorpe, Whitby in North Yorkshire, England, approximately 75 km east of York. The area of interest is more than 700 km2. The £3.2 billion project is to develop the Woodsmith Mine to extract polyhalite, and a tunnel system to transport it to a materials handling facility and harbour at Teesside. The site is the world's largest and highest-grade deposit of polyhalite and is expected to produce 20 million tonnes of polyhalite, potash and POLY4 per annum, as well as create over 1,000 direct jobs and many more indirectly. It has the potential to generate over £2 billion of annual exports for the UK. As the project will require mining to be undertaken in the North York Moors National Park, many objections were raised about the mine. Sirius Minerals has gone to great lengths to ensure that the project is sensitive to the local landscape, including: mineshaft head frames that will be positioned below ground to reduce their visual impact; surface buildings will be kept to a minimum; and the entire site will be landscaped and screened by existing woodland to blend in with the surrounding area. The project will also abide by strict environmental limits which govern our activity during the construction phase."

Jan 1, 2019

By Nicholas J. Welham

"The effect of extended ball milling has been studied for two industrial processes: (1) the processing of metal sulphide concentrates; and (2) the carbothermic reduction of ilmenite to synthetic rutile. The plant concentrates were a gold ore with 128 g/t Au of which 8% was non-refractory and a zinc concentrate with copper impurities.The gold concentrate showed complete dissolution of the gold bearing minerals after milling giving almost complete gold liberation. The zinc concentrate showed almost all of the sulphides had solubilized leaving the gangue and elemental sulphur. A study of pure pyrite and arsenopyrite shows that selective dissolution should be possible by a simple leaching process directly after milling.The milling of ilmenite and coal together results in a temperature decrease of 150°C in the subsequent carbothermic reduction of ilmenite, in addition to improving both the rate of reaction and the selectivity of reduction to rutile. IntroductionAlmost all mineral processing plants use mills for the size reduction of particles prior to physical and chemical processing. When continuing beyond size reduction the energy transferred causes deformation, breakage and realloying of particles giving a steady-state particle size. The breaking also causes increasing damage to the crystal structure by formation of smaller grains giving an increasing number of grain boundaries and increasing crystalline defects due to deformation. The increasing number of grain boundaries and defects leads to increased reactivity, which can be seen directly by a reaction within the mill, or indirectly, via a decrease in the subsequent annealing temperature required for reaction."

Jan 1, 1997

By J. C. White

"During the early development of the Mattabi Mine in 1970, discussions with the Ontario Government revealed their policy of prohibiting, as much as possible, the development of new, isolated, single-industry townsites. Subsequently, Mattabi located its first housing in the Township of Ignace, which is situated 50 miles from the site of the mine and plant. Over 200 employees now commute 100 miles daily to and from work.This paper describes the experience gained and discusses the advantages and disadvantages of a remote townsite."

Jan 1, 1976

By R. Q. Honaker

It has been shown that naturally hydrophobic carbonaceous materials such as coal and graphite can be selectively coagulated and separated from hydrophilic impurities without using oily agglomerants, flocculants or electrolytes. The coagulation occurs at C-potentials significantly higher than those predicted by the classical DLVO theory, suggesting that it is driven by the hydrophobic interaction. In the present work, the energy barriers for the coagulation of a hydrophobic coal sample have been calculated using the extended DLVO theory which incorporates the hydrophobic interaction energy in addition to the dispersion and the electrostatic energies. For the coagulation of minerals present in the coal, the classical DLVO theory has been used for the energy barrier calculation. The results of these calculations provide an excellent correlation with the results of a series of Selective Hydrophobic Coagulation (SHC) tests conducted with run-of-mine coal and graphite samples.

Jan 1, 2004

By S. M. Fatemi-Varzaneh

The AZ31 magnesium alloy is considered as a promising alloy in various applications and industries. Furthermore, to design a proper hot working process (rolling, forging and extrusion), the assessment of hot working behaviour of the alloy is necessitated. Accordingly, the hot deformation behaviour of AZ31 alloy was studied through hot compression testing method. The latter was carried out in a wide range of temperature (523 K to 783 K) and strain rates. The obtained true stress-true strain curves and final microstructures were examined and a partial melting was realized at 740 K. It was concluded that the presence of liquid did change the deformation mechanisms thereby affecting the flow behaviour.

Jan 1, 2005

By Tony Szwilski

Using Unity 3D as a collaborative multi-user virtual on-line environment, an interactive virtual underground mine platform (IVUMP) is being developed to provide on-line access to mine safety preparedness training with a focus on mine emergency response exercises (MEREs). Communication and information flow among MERE participants and their actions can be monitored, recorded and evaluated. A mine ventilation simulation utility VFIRE is being incorporated to enhance the realism and interactive nature of the ?in-world? exercises as well as extend its functionality to include training in real-time ventilation and fire control.

Aug 1, 2013

By K. Kawagishi, J. Ang, A. Sato, H. Harada

"We have recently proposed a new ""EQ Coating"" bond coat system to solve the problem of secondary reaction zone (SRZ) formation caused by bond coats applied on the hot section components of modem jet engines. A viable EQ coating alloy was previously found for a representative znd generation superalloy, TMS-82+. It would be ideal if the same could be done for a representative 5th generation superalloy, TMS-173. In this paper, we will show that the coating with the best oxidation resistance in the EQ system of TMS-173, although possessing considerably better resistance than TMS-173, did not have sufficient oxidation resistance. In order to improve the oxidation resistance of the EQ coating for TMS-173, we have ventured into ""Pseudo-EQ coatings"". A diffusion couple between the Pseudo-EQ coating and TMS-173, after 300hrs at 1100°C, had a 0-15µm IDZ, but no SRZ. A diffusion couple between a conventional coating and TMS-173 formed a 80-150 µm SRZ. After a 1 hr oxidation test at 1100°C, the PseudoEQ coating formed a thinner oxide layer than the EQ coating, but still contained NiO and spinel. Aerospace"

Jan 1, 2006

By J. F. Wright

Gold-bearing quartz veins and replacement chalcopyrite deposits are the two important types of metallic mineral deposits of the east central Manitoba mining district. The gold-bearing veins occur along Manigotagan valley, northwest for 25 miles from Beresford lake, and the copper deposits along Oiseau valley, between Oiseau lake and the east end of Lac du Bonnet. Lithium-bearing minerals of possible commercial value have recently been discovered in pegmatite along Winnipeg river about 10 miles east of Point du Bois. There are also prospect pits with showings of galena, sphalerite, cobaltite, pentlandite, nickeliferous pyrrhotite, arsenopyrite, pyrite, molybdenite, cassiterite, and other minerals, but the various occurrences of these minerals, as exposed, are small. The bedrock and mineral deposits of this mining district are Precambrian and resemble in many respects the formations and mip.eral occurrences of western and northern Ontario. Although prospectors visited eastern Manitoba at intervals during the last fifty years, effective prospecting did not begin until 1913 or 1914, and not until 1923 were skilfully directed, systematic explorations undertaken. It is true, that between 1913 and 1923 considerable sums were expended in a number of attempts at mining and milling the gold-quartz ore, but these enterprises failed partly through poor management or attempts to develop veins that were too small or too low-grade to be worked at a profit under the existing conditions of transportation and power supply.

Jan 1, 1925

By Robert A. MacGregor

"Following several months of test work, water leaching in mined-out areas at Stanrock commenced on a production basis in February, 1963. A combination of fast high-pres-sure washing and rewashing of stopes on a predetermined cycle, and the intermittent sprinkling of low-grade heaps, using both fresh water and recirculated acid water, has proved most successful. There was also a correlation of daily sampling data points to a relationship between the leach water grade and the grade of the material being washed, the leaching time and the location along the dip. An increasing tolerance for uranium by the acid-producing bacteria is also indicated. A steady production rate of 10,000 to 12,000 lbs. of u.08 per month is being maintained, with an over-all mine water grade of 0.25 lb. per ton and a pH of 2.3."

Jan 1, 1966