Search Documents

By M. E. Stutt, R. H. Rehder

"The mining industry is taking advantage of the increased performance resulting from the use of variable speed A C drives for large motors. This technology provides increased efficiency under the variable speed and torque requirements of such drives as mine hoists, conveyors, and air moving equipment. The technology does introduce voltage spikes on the voltage wave form that stress the insulation system to a greater degree than would occur with a constant voltage source. These voltage spikes must be considered in the design of the insulation system used for these motors.BackgroundHistorically the insulation systems for large AC motors were designed to withstand with reasonable life the voltage stresses of a 60 Hz constant sinusoidal voltage. One of the design tests is a voltage endurance test that requires the application of a 60 Hz voltage from conductor to ground equal to four to five times normal and establishing a time to failure. These higher than normal voltages accelerate the normal aging process by causing extensive partial discharge activity (corona) within the insulation system and the time to failure is a relative indication of insulation life.In addition to the voltage endurance test at 60 Hz, the individual coils are subjected to a surge voltage test to establish the withstand capability of the turn to turn insulation under switching surge conditions. The surge voltage is a fast rise time, 0.2 microsecond to crest value, voltage spike that can be caused by a circuit breaker or contactor closing operation. These voltage spikes can have a crest value of greater than 3.5 times the normal line to ground crest voltage of the normal 60 Hz power supply. The standard withstand test value is thus 3.5 times normal line to ground voltage. Because the voltage surges or spikes occur mainly during start and stop switching conditions, voltage endurance under these conditions has not been a major factor in insulation system design."

Jan 1, 1995

By C. H. Ash

"Abstract-The Red Chris Cu-Au deposit (522.7 Mt at 0.35% Cu and 0.27 g/t Au), northwestern British Columbia, is one of several pre-accretionary porphyry systems in the Cordillera of western Canada. It is hosted by an Early Jurassic hornblende monzonite to quartz monzodiorite porphyry which forms part of a suite of dikes and stocks that intrude Late Triassic volcanic strata. Major and trace element chemical data suggest that these Early Jurassic intrusions have compositions which fall on the boundary between alkalic and calc-alkalic compositions. Alteration and mineralization in the Red Chris deposit are more typical of calc-alkaline porphyry systems with abundant potassic, sericitic and argillic assemblages and quartz-rich stockworks. It lacks Na- and Ca-bearing silicate assemblages which characterize the alkalic porphyry deposits of British Columbia. One of the more unusual features of the deposit is the abundance of carbonate alteration and veins which occur throughout the hydrothermal history of the deposit. This type of alteration and veining is more typical of alkalic porphyry deposits. The composition of the carbonates vary both temporally and spatially with different alteration zones. Potassic zones, which are characterized by orthoclase±albite±quartz±chalcopyrite±bornite± magnetite±hematite and Au/Cu ratios of 1:1 (g/t Au:% Cu), contain minor siderite veins and alteration. Quartz-sericite-carbonate (QSC) zones overprint earlier potassic alteration and comprise quartz+ankerite+sericite+pyrite+chalcopyrite with Au/Cu ratios of 0.5:1 (g/t Au:% Cu). Ankerite is the main carbonate in this stage but has a variable composition with a more Fe-rich variety associated with mineralized veins. Localized chlorite-carbonate alteration zones, characterized by chlorite+ carbonate+quartz±kaolinite±pyrite±gypsum and high Au/Cu ratios [2 to 3.5:1; (g/t Au:% Cu)], contain predominantly calcite. Late stage carbonate-gypsum veins have an ankerite to dolomite composition which is very similar to the regional carbonate alteration and veins."

Jan 1, 1997

By C. H. Ash

"The Red Chris Cu-Au deposit (522.7 Mt at 0.35% Cu and 0.27 g/t Au), northwestern British Columbia, is one of several pre-accretionary porphyry systems in the Cordillera of westernCanada. It is hosted by an Early Jurassic hornblende monzonite to quartz monzodiorite porphyry which forms part of a suite of dikes and stocks that intrude Late Triassic volcanic strata. Major and trace element chemical data suggest that these Early Jurassic intrusions have compositions which fall on the boundary between alkalic and calc-alkalic compositions. Alteration and mineralization in the Red Chris deposit are more typical of calc-alkaline porphyry systems with abundant potassic, sericitic and argillic assemblages and quartz-rich stockworks. It lacks Na- and Ca-bearing silicate assemblages which characterize the alkalic porphyry deposits of British Columbia. One of the more unusual features of the deposit is the abundance of carbonate alteration and veins which occur throughout the hydrothermal history of the deposit. This type of alteration and veining is more typical of alkalic porphyry deposits.The composition of the carbonates vary both temporally and spatially with different alteration zones. Potassic zones, which are characterized by orthoclase±albite±quartz±chalcopyrite±bor-nite±magnetite±hematite and Au/Cu ratios of 1:1 (g/t Au:% Cu), contain minor siderite veins and alteration. Quartz-sericite-carbonate (QSC) zones overprint earlier potassic alteration and comprisequartz+ankerite+sericite+pyrite+chalcopyrite with Au/Cu ratios of 0.5:1 (g/t Au:% Cu). Ankerite isthe main carbonate in this stage but has a variable composition with a more Fe-rich variety associated with mineralized veins. Localized chlorite-carbonate alteration zones, characterized by chlorite+carbonate+quartz±kaolinite±pyrite±gypsum and high Au/Cu ratios [2 to 3.5:1; (g/t Au:% Cu)],contain predominantly calcite. Late stage carbonate-gypsum veins have an ankerite to dolomite com-position which is very similar to the regional carbonate alteration and veins."

Jan 1, 1997

By Yugo Mitani, Tatsuya Kato, Chiharu Tokoro, Abdullah Al Mamun

Acid mine drainage (AMD), which is a major source of mining pollution, often contains ferric and/or ferrous ions together with several toxic elements. The ferric and ferrous ions in AMD precipitate in several mineralogical forms after neutralization, and the ferric/ferrous precipitates become the main component of the sludge generated after AMD treatment. The precipitates are also good absorbents for several toxic elements. To avoid generation of voluminous sludges and the re-dissolution of toxic elements from the sludge, it is very important to generate well-draining and efficiently adsorbing sludges by controlling the mineralogical form of the ferric/ferrous precipitates. Green rust, which is ferric and ferrous hydroxide, is a double layer hydroxide which is able to sorb several toxic elements. The green rust transforms to goethite or lepidocrocite by rapid oxidation, whereas it transforms to magnetite at ambient temperature by slow oxidation. The magnetite is also good absorbent especially for toxic cations and it makes a compact sludge due to its magnetic properties. We investigated the magnetite generation process at ambient temperature in detail. The magnetite generation process can be divided into three steps; (i) oxidation of Fe(II), (ii) Fe(II) surface complexation to Fe(III) hydroxide, and (iii) crystallization of magnetite. More magnetite can form when the oxidation rate is slower than the crystallization rate, and optimum conditions for its formation are at pH 9.5 with mild agitation. Ferrihydrite is the most common precipitate and it is able to sorb many different toxic elements. However, it drains badly and its solid/liquid separation properties are poor. We investigated the removal mechanism of several toxic elements by co-precipitation with ferrihydrite. We confirmed that the removal mechanism by co-precipitation partly involved surface precipitation when the initial ratio of toxic elements to ferric ion was high, although the main mechanism was always surface complexation. When surface precipitation occurred, highly efficient toxic element removal with ferrihydrite could be achieved.

Jan 1, 2016

By Ken Musgrave

"What Most Effective Management Does?It must satisfy the demands, of three groups of people: owners, employees and the public.OwnersOwners want profitable operations that will pay them a return on their investment, plus operations managed for long life. Many owners are also concerned with employee's well being and their company's public image.EmployeesJob security and a good income are probably still the most important demands, however, as time goes by, employees are also demanding more involvement in safety issues, working conditions, and even how work is done.The PublicThe public requires acceptable environmental standards, as well as enjoying the prosperity supplied by a successful operation.How are Mines Managed?Most mines are managed very traditionally. The basic credo is that the managers make the decisions, and the hourly, and junior salaried employees do what they are told. Clearly this is the extreme case, epitomized by the long service shift boss who might say ""It took twenty-years to become a shift boss, and no miner is going to tell me what to do"" .There are some exceptions, two notable ones being Campbell-Chibougamau, and T.G.S. (now Kidd Creek Mines) which, in very different circumstances, decided on a more participative style.Campbell-Chibougamau, having closed down due to unprofitable operations, reopened, using a team structure with working leaders, and a system for sharing gains against cost targets with employees. Although the system has some problems, and development miners are bonused conventionally, this has been a basically successful program.Texasgulf Sulphur, a company with a history of non-union operations, and a participative management style, made a corporate decision to operate their Kidd Creek Mine in the same way. The orebody was rich enough to allow them the luxury to do this, but they have never had a strike, so perhaps they have more than saved the cost of the benefits and salaries they needed to pay. They also reward employees with a stock distribution scheme based on service and earnings."

Jan 1, 1985

By A. C. Bonnier

"INTRODUCTIONI have been asked to make available our method of determining the ""Live Inventory"" within a gravity type thickener. The ""Live Inventory"" being that tonnage compatible with the optimum underflow density that satisfies the process requirements.One prerequisite of the calculations is the proper determination of the final pumpable underflow density. A further requirement is that, prior to shutdown, the thickener has been operated properly, particularly that it has not been operated for storage capacity.Until recently I had few chances to check the method. However, I was most fortunate to have had a recent opportunity covering several months on a 300 ft diameter thickener at a plant in the U.S.A., wherein the method was tested and verified many times. The method proved accurate in that our calculated tonnage checked with the actual dried physical inventory of the drying facility.At the precise moment that the feed to the thickener was shut down, a per cent solid determination was made at the critical place and the tonnage in ""Live Inventory"" determined. Let us say that at the moment the thickener U' Flow solids was 20%. The thickener then was allowed to cperate until the U' Flow solids dropped below 20%, at which time the thickener was deemed to be relieved. Anything much less than 20% was not suitable to the subsequent centrifuge operation.Most large metallurgical thickeners have a configuration of three slopes at the thickener ""bed"". These slopes are dictated by the raking blades and are shown on the manufacturers' erection drawings. The first slope is from the outer periphery and generally takes up a distance of about 60% of the radius, the second slope generally taking up the remaining 40%. Within this 40% area, there is usually another slope taken up by the cone on ""B"" type thickeners or an actual steeper inner slope on ""C"" type thickeners."

Jan 1, 1989

By J. Baz-Dresch

"The most cost-effective method of placement of the high strength fill used in the Cannon Mine' s overhand cut-and-f ill bench stopes was determined to be truck haulage. Constraint s imposed by the mine layout dictated the use of a truck which could dump its load in a fifteen-foot high drift. The Dux Teledumper truck was selected as the most suitable unit for this application based upon operational and maintenance parameters which included a telescoping, tilting dump box; large load capacity; and robust construction. Development of the truck continues through the cooperation between the manufacturer and user. INTRODUCTIONThe Cannon Mine is situated in the centre of Washington state, approximately midway between the cities of Spokane on the east and Seattle on the west. The mine complex is located three block s south of the Wenatchee city limits at the eastern base of the Cascade Mountain range.Asam era Minerals (U.S.) Inc., with 5I% ownership, operates the Cannon Mine. Breakwater Resources, Ltd. holds the remaining 49%.Annual paroduction is 520 000 tons per year, presently on a 21-shift per week operating schedule for both the mine and the mill.All production is presently won by overhand bench stoping with backfill. Stoping starts with 15-ft high by 24- or 30-ft wide sill cuts driven above and below a stope block . A drop rai se and slot are used to open a bench which is then slabbed toward the open slot. Truck-placed backfill is dumped into the mined - out stope from the upper sill cut. This stoping sequence is repeated until the top of the ore block is reached . The top sill cut is then tightly filled with backfill to minimize subsidence and to provide adequate roof support during extraction of the pillars.Mining equipment consists of hydraulic drills and rubber-tired, diesel scoops and trucks."

Jan 1, 1989

By Bern Klein, A. Tugba Cebeci, Libin Tong

"Sensor based sorting faces two main challenges related to limited capacity/throughput and the ability of sensors to accurately discriminate based on estimated grades. This paper is aimed at improving sensor discrimination. Sensors have the ability to measure more than a single response. X-ray fluorescence (XRF) can detect and provide concentration information about a range of elements. Similarly, electromagnetic sensors (EMs) can generate magnetic susceptibility and conductivity responses over a range of frequency levels. The sensors thereby provide a response signature rather than a simply a single response that is a proxy for a metal grade. Furthermore, integrating sensor responses can improve the discrimination of metal bearing rock from waste. A study was conducted on a gold ore to assess sortability using XRF and EM sensors. A multi-variable regression approach was used to develop models that included a range of responses. Correlations improved significantly when compared to single response correlations. The approach showed that both positive and negative correlations contributed to the improved correlations. Stepwise regression simplified the models and showed that 2nd order interaction effects can be important. The approach also showed that combining different responses can improve discrimination accuracy. An important outcome of the study was that an ore that had been consider not to be sortable was determined to be sortable through the application of an approach that used the sensor responses in a more intelligent manner.INTRODUCTIONMining is aimed at recovering valuable minerals from their host rocks. Many methods are used to recover valuable minerals, and finding efficient and cost-effective ways is the key in research and production. . Ore sorting technology is fitting this definition. It not only discards waste rocks away from the concentrator but also recovers metal bearing ore particles that could be lost to the waste dump. The benefits of ore sorting include increased energy efficiency and reduced water and reagent usage in the downstream operations (Bamber, 2008; Gunson, Klein, Veiga, & Dunbar, 2012; Mazhary & Klein, 2015; Robben, Wotruba, Robben, von Ketelhodt, & Kowalzcyk, 2013)."

Jan 1, 2016

By P. Reyes

The start up and operational optimization of the No. 3 Oxygen Plant at the Caletones Copper Smelter of the Codelco - Chile El Teniente Division is summarized. In addition, the economic impact of such optimization on the production cost of oxygen and others aspects associated to the operational robustness as well is detailed.

Jan 1, 2007

By Ronald B. DeDiemar

This paper will present the intrinsic factors of a cone crusher that affect performance, develop and define an ideal feed gradation for a cone crusher and, finally, bring out an important new development in computer design of crushing chambers and show an ability to predict crusher performance without trial-and-error methods.

Jan 1, 1979

Purpose of TSUG Continuous Improvement in Mining Share Best Practises Exchange Ideas Network for Frontline Supervisors and Middle Management Meetings ? Two per Year -Spring and Fall ? Thirty Five to Forty Attendees ? Rotate Between Host Properties ? Host Mine Provides ? Meeting Room for One Day Tour of Mine and Maintenance facilities on Second Day

May 1, 2010

By Peter McGoldrick

This Talk ?Australian deposits in world context ?Geological setting: the importance of the basin fill ?Key deposit features using HYC (McArthur River) and Century as examples ?The difference between Aussies & Canuuks(that is between Australian & Canadian sedexdeposits!) ?Timing of mineralization ?Sources for metals and ore fluids ?What makes a super giant sedexdeposit?

May 1, 2006

By Pierre Laliberté

Introduction ??Mine ventilation is a major consumer of power in underground mining, including air heating (winter) and air conditioning (deep mines). ??Any advances, including the development of low emission vehicles, that can improve underground air quality can reduce ventilation demand, and likewise reduce costs and energy consumption, including their associated greenhouse gas emissions.

Nov 1, 2011

By S M. Roscoe

Relationships of Noranda sulphide deposits to volcanic rocks are reviewed and chemical variations within the volcanic sequence are described. The assemblages of minor elements in the pyrites and pyrrhotites of the Noranda and l\llatagami deposits are similar and are characterized by a high content of cobalt, tin and other elements. Isotopic compositions of lead, other geochronological data and stratigraphically disposed zonal distributions of sulphides and minor elements indicate that the deposits were formed prior to folding and metamorphism. Lead isotope data indicate that the Matagami deposits, and several others, were probably formed about 2.95 x 109 years ago and that the Noranda deposits may be about 50 million years younger. The volcanic sequence at Noranda is younger than the thick sequences bordering it on the east and on the west. The relationships are consistent with the hypothesis that these strata-bound sul1>hide de-posits are coeval with their associated volcanic rocks. T HE writer has been engaged in a metallogenic study of the region between Sault Ste. Marie and Chibougamau. An essential objective of this study is the classification of mineral deposits with regard to their composition, form, geological

Jan 1, 1965

By James K. B. Booth

The natural crustal abundances of the principle metals of commerce are examined in relation to production and prices for each metal. Two factors, the abundance x price ratio (BP factor) and abundance/production (B/T factor) are listed for each metal. Ideally, for these desirable commercial metals, each factor should be a constant and the same for all metals; comparing the divergences for the full list of metals allows conclusions to be drawn on the relative degree of natural availability of each metal and the ease or difficulty of winning the metal from the earth's crust. Plotting the two factors for each metal over the past decade of steady industrial usage illustrates the anomalous position of copper and, to a lesser degree, molybdenum and it is concluded that over the long term the price of copper will continue to rise steeply. Possible future prices for copper are examined and a suggested preferred order of ranking of the metals as exploration targets would be copper, nickel, tin, zinc, silver, molybdenum and lead, for the near term, with molybdenum possibly increasing its ranking in the list within the next decade.

Jan 1, 1971

By D D. Deacon

A brief description is given of the requirements which No. 4 Shaft has been designed to meet and of the methods by which two-stage winding of rock has been accommodated in a single shaft sunk to a depth of 7,421 ft. This is followed by a consideration of the factors which led to the decision to sink the shaft as rapidly as possible. Introduction T HE No. 4 Shaft of Hartebeest-fontein Gold Mining Company, Ltd., has been sited to serve the deep southern area of the mine, some 1,500 claims in extent, between the elevations of 6,250 and 7,300 ft. below surface. From this area, some two-thirds of the mine production will ultimately be obtained. Above the 6,-250-ft. elevation, an existing shaft hoisting system, situated adjacent to the reduction plant, is of adequate capacity to cater for all ore hoisted to surface for milling. No. 4 Shaft will therefore be required to provide downcast ventilation of 1,000,000 c.f.m., together with surface hoisting facilities for men, material and development rock and underground hoisting

Jan 1, 1965

By B. F. Osborne

"A new sensor cannot be considered in isolation from the process in which it is utilized. This paper, describing an on-stream particle size analyzer, therefore gives considerable emphasis to the slurry handling techniques employed to ensure that the instrument is presented with a representative sample. A new sampler is described, which continuously abstracts a small, representative sample from a closed pipeline containing a flowing slurry. This sample is then diluted, thoroughly mixed and pumped to a head tank, from where a continuous stream is fed at a constant rate to the size analyzer. Data are presented to show that particle size segregation is minimal throughout this sampling and sample preparation. A continuous particle size analyzer based on a separation principle is described, and the basic parameters of size distributions, and how they relate to this particular instrument, are considered. Typical results are given. An electronic system is presented which accepts the basic sensor outputs, and converts these to a particle size signal suitable for process control. Finally, the use of an inplant computer to process the sensor signals to obtain a particle size signal is briefly considered."

Jan 1, 1972

By K. Jomoto, H. Majima

"Experimental work has been attempted to find a useful criterion of comminution which can be determined simply in a laboratory. The suitability of the ratio of the square of tensile strength to Young's modulus, St2/E, previously derived from the theory of elasticity as a criterion of comminution, was examined measuring tensile strength, Young's modulus and critical height for drop-weight impact of five different rocks. However, satisfactory correlation between St2 /E and critical height has not been obtained, suggesting the necessity of further experimental verification of the representative value of Young's modulus of rocks. The plot of St2 vs. critical height, however, shows one-to-one correspondence, and this finding suggests that St• may be a useful criterion of impact crushing. Also, a close relationship was observed between st• and the energy index for tumbling mill grinding of •the sample rocks. It is confirmed from these findings that the quantity St• is a useful criterion of comminution of rocks, not only for impact crushing but also for tumbling mill grinding. As shown in the experimental part of this paper, the determination ol St with irregularly shaped specimens is simple."

Jan 1, 1972

By Andrew J. Troop

"VAUGHAN THOMPSON designed the Thompson retrievable diamond drill wedge and reaming assembly in 1948. Since 1950, the Hudson Bay Exploration and Development Company, Limited has used the method extensively. The wedge, setting tool, and reamer have been modified slightly since they were first introduced. In 1951, Mr. Thompson designed the Thompson arc cutter. The purpose of this tool is to decrease effectively the diameter of the arc cut, using standard drilling tools. This directional drilling device is usually employed when a branch hole is desired. The Thompson arc cutter has been used with success at Birch Lake, Saskatchewan, at the property of Cuprus Mines, Limited, Manitoba, and at Thompson Lake, Manitoba.UsesThe Thompson retrievable wedge provides a simple method for:(1) Re-drilling lost core sections(2) Re-sampling sections of old holes(3) By-passing lost tools Correcting the direction of a hole(4) Drilling a branch hole to obtain intersections at a higher elevation than the original holePrevious to the spring of 1951, the wedge was used only for the first four of these purposes. Recently it has been employed extensively for drilling branch holes."

Jan 1, 1953

By G. Banini

Prior to installation of High Pressure Grinding Rolls (HPGR) at PT Freeport Indonesia (PT-FI) a series of laboratory tests were carried out to determine the design parameters and also determine key performance indicators (KPIs) for the industrial unit. The design parameters derived from the lab test work were then scaled up to estimate the industrial capacity of the HPGRs to be installed. These parameters include specific power draw, specific throughput, and specific force, rolls speed, product size distribution and wear rate of the rolls. This paper compares the performance of the scale-up procedure against the installed industrial size HPGR. Overall, the specific throughput of the industrial size HPGR is higher by a minimum of 30% compared to the expected scale-up value. As a result of the high specific throughput, the specific power draw and grind sizes are below the scale-up expectations in the commercial application. The impact of these factors also contribute to a lower than expected wear rate on the industrial rolls. Installed rolls achieved a service life in excess of 18,500 hours relative to the target of 6,850 hours predicted from the laboratory testing.

Jan 1, 2012