Search Documents

By Ralph Harris, Xia Qi, Frank Komsic

"Gold cyanidation kinetics which are often limited in commercial operations by the rate of oxygen dissolution from gas bubbles into the slurry, are discussed. Emerging technologies for improving the rate of oxygen dissolution are compared and the gas efficiency, energy use and operating performance of inverted cones and a device based on a jet diffuser are examined. The effect of solids loading is also reviewed and a relationship between operating parameters and the kilograms oxygen dissolved per kilowatt-hour is presented.Inverted cones are shown to create slurry settling problems at high gas flow rates and surface tension lowering agents are shown not to greatly improve the overall rates of oxygen dissolution.The novel jet diffuser technology operates at a range of gas to liquid ratios that improves its energy use over conventional technology and the performance of a number of designs are discussed.Gas efficiencies as high as 35% were observed with the novel diffusers at 40 cm diffuser immersion and are expected to increase at greater immersions. Energy use of 1.8 kg 02 I kWh were estimated for prototype full size diffusers operating at 100 cm immersion. Energy use of 3.S kg 02 /kWh is conservatively expected at 600 cm immersion.IntroductionGold ExtractionGold that can not be recovered by gravity separation can be recovered by either the Merrill-Crow process or the newer carbon in pulp (CIP) or carbon in leach (CIL) processes 1. Reductions in operating costs and improvements in gold recovery are central mill operating strategies. The present paper examines the potential for improvement that can be achieved in the gold cyanidation step of gold recovery. This paper introduces a number of emerging technologies and provides a basis for comparison of the performance. It shows that the basis for comparison of a particular technology depends on the type of gold extraction circuit employed and the type of reactants employed."

Jan 1, 1996

By P. L. Claessens, S. Belisle, C. Bowen

"Use of zinc shot feed is a well-established procedure among North American electro-galvanizers. This form of zinc is easy to handle and relatively inexpensive when compared with zinc oxide. This paper reports results on the kinetics of zinc shot dissolution in traditional pure zinc solutions and in electrolytes used for the plating of nickel/zinc alloys. Despite the cementation of minor amounts of nickel in the latter solution, acceptable dissolution rates of the zinc shot can be achieved through proper adjustment of the solution velocity. Under these conditions, the nickel shell produced by cementation is continuously abraded, exposing the underlying zinc.IntroductionThe use of insoluble, noble metal-containing anodes rather than soluble zinc anodes for the operation of high current density electro-galvanizing lines has gained almost universal acceptance. Two major reasons for this trend are:• improved control of the process by virtue of constant inter-electrode distance; and• increased productivity because the operation of the lines does not require the relatively frequent interruptions for replacement of consumed anodes .The results of the principal anode and cathode reactions are, respectively, depletion of the zinc content of the electrolyte and the increase on its acidity;"

Jan 1, 1991

By A. Nielsen

"The Polaris mining operation (Fig. I) is located on Little Cornwallis Island in the Canadian Arctic, an area with a very limited shipping season and a hostile climate. The operation consists of the underground works, barge-mounted concentrator facilities, concentrate storage and shipping facilities, a personnel accommodation complex and an airstrip.The electrical energy for the operation is provided by four 2.3 MW diesel-generators installed on the barge. The power is distributed through a 4.16 KV system connected directly to the generators and to the large motors. All other loads are supplied at 600 V or 120 V.The power plant has been designed as a Total Energy System with maximum energy efficiency and thus designed for maximum heat recovery. The waste heat recovered on a year 'round basis is expected to be sufficient for the process heating and drying as well as the space heating for offices and accommodations. The engine cooling system consists of two glycol-water loops, a "" cold"" loop for charge air and lube oil cooling and a ""warm"" loop for jacket water cooling. Each loop is complete with heat exchangers f or heat recovery and out-door forced air radiators to dispose of excess heat. A water loop in the concentrator area transfers the heat from the jacket water loop and the exhaust gas boiler to the space heating equipment, the process and the heating system for the accommodations. Part of the exhaust gas is diverted to the concentrate dryers.IntroductionThe Polaris Mine is a highly mechanized, trackless mine with access through a decline. Drill equipment is electrically powered to minimize fumes and heat. Dry development and production drilling eliminates the need for an underground water supply system.The concentrator, power generators, work shops and auxiliary facilities are located on a barge which is beached in a prepared berth on the shore of Crozier Strait. Oil storage tanks, concentrate storage and accommodation buildings are built on shore. The concentrate storage building ha s a 12-month capacity and is fed from the concentrator by a conveyor system.The accommodation building houses up to 240 people, includes administration office, dining and recreation facilities. The complex is housed in on e interconnected building with public use areas alternating with accommodation units.At full production annual concentrate shipments will amount to about 220,000 wet tonnes. This will be accommodated by about 8 shipments during the regular shipping period-August 15 to October 15. Re-supply of general cargo and fuel will be carried out annually in about 3 shipments within the same period."

Jan 1, 1984

By Angela L. Paveley

Economic viability of base metal mining is complicated by a volatile market that can cause fluctuations in the growth and stability of the mining industry. Nickel is mined primarily for use in manufacturing industrial stainless steel and plating materials. It is essential that nickel production be sufficient to respond to current and future market demand. A Post-Pillar cut and fill mining complex is currently producing nickel sulfide in Northern Manitoba. From 2006 this area has shown a steady increase in the annual production, rising from 11 million pounds to 25 million pounds in 2010, and accounting for 33% of the total production for the Manitoba Operations. It is expected that fine-tuning the mining process can safely enhance ore recovery, improve production consistency, and increase economic viability of the deposit. The Post-Pillar Optimization study was initiated by the local technical and operational departments at the mine and analyzed from July 2010 to March 2011. The purpose of this study was to determine if portions of non-recoverable pillars can be slashed without jeopardizing pillar strength. This ideal case would optimize ore recovery and reduce variability in the ore mining rate. Numerical modeling and geo-mechanical material properties analyses, completed by the rock mechanics group, define the maximum drift width at 32 feet and the minimum pillar width at 18 feet. Thus, it was suggested that up to 3 feet could be slashed from two sides of the standard 24 foot pillars without damaging ground integrity. The field data collected indicates that additional ore could be recovered without compromising the safety of the workplace and the integrity of the complex. Consequently, technical and operational groups work jointly to achieve pillar optimization. Approximately 500,000 pounds of nickel was extracted from the complex via pillar optimization from July 2010 to March 2011. Economic analyses show the pillar optimization method developed for the mining complex is a proven, value-added opportunity. The mining complex remains a safe workplace and has retained ground integrity.

Nov 1, 2011

By Delio J-J Tortosa, Fred F. Langford

"The Cenex orebody occurs at the intersection of northwest and northeast-trending fault zones that formed during post-Hudsonian uplift. The ore is localized in breccia zones, along faults, and in veins and adjacent wallrocks. The host rocks are Tazin quartzo-fe/dspathic mylonites and ultramylonites and chloritesericite- quartz-graphite-feldspar mylonite schist. The uraniumbearing minerals are finely disseminated pitchblende and uraniferous titanate.The earliest mineralization may have been associated with /ate-stage retrograde metamorphism in the mylonite schist. The main stages of mineralization were associated with brecciation, hematization, carbonatization, and chloritization of the mylonites and ultramylonites. Uranium mineralization was clearly much later than any igneous or metamorphic activity associated with the Hudsonian orogeny.Late post-orogenic uplift, erosion, and deposition of the Martin continental clastics in fault basins were coeval with uranium mineralization. The deposit is consistent with a meteoric-hydrologic system constituting a source for orebearing fluids, hence the close spatial relationship of the uranium deposits in the Beaverlodge area with the basal unconformity of the Martin Group."

Jan 1, 1986

By O. Moselhi

Material can be seen as the fuel needed to execute the project from inception to completion. Material installed provides good indicators of progress achieved onsite vis-a-vis project schedule performance. It correlates well with the role of the schedule performance index (SPI) of the earned value method (EVM). Material is recognized to have a significant impact on achieved progress for physical completion of project activities. This paper presents a study on the development of material status index (MSI) in support of the EVM. Unlike the SPI, the newly developed index account for the criticality of project activities. This is carried out considering the total float of each activity, percent float (i.e. the ratio of float to activity duration) and the total float of the path on which the activity is located. MSI, can independently and jointly with SPI provide root causes behind problems encountered during project execution. In turn MSI can reveal material related factors behind the performance detected by joint interpretation of the two indices. MSI serves to provide added value in alerting management to take corrective actions. While SPI and MSI may have different values, they can jointly augment and enrich the captured project status based on EVM. To demonstrate the capabilities of the developed MSI method, it is implemented on a case study. The case encompasses the construction schedule of a hydro power station constructed in northern Quebec. Different scenarios are adapted from the real case to demonstrate a set of practical aspects of the developed index. The results generated from the analysis of the case study illustrate the useful features of MSI beyond those of the traditional SPI on two fronts; causation and the considerations of criticalities of actives.

Aug 1, 2013

By H. Dundar

The first application of High Pressure Grinding Rolls was in 1985 at a cement plant, for the purpose of capacity improvement. Then various circuit configurations were derived to achieve a reduction in overall specific energy consumption, by transferring more of the grinding required to the HPGR. In most circuit configurations, the recycle of fines is required for effective breakage between the rollers. By increasing the fines amount in the feed material to a specific level within the recycling load, a uniform material bed is created and a higher pressure gradient along the roller width is obtained, resulting in compact flakes, including more fines. The fines recycle results in enhancement of the interparticle breakage. This paper will discuss the effect of the feed size distribution on HPGR performance.

Jan 1, 2012

By Pablo González, Rodolfo Espinosa, Jose-Luis Noyola, Sergio Cossio

"Minera Penmont, at La Herradura, is a joint venture between Industrias Peñoles, S.A. de C.V., and Newmont Mining Corporation. The mine is located in the northern Mexican state of Sonora. La Herradura consists of an open pit mine with two-stage crushing and heap leaching facility, the gold is recovered from the pregnant solution using the Merrill-Crowe process; production began in July 1998. La Herradura produces about 130,000 gold ounces per year, and treatment capacity is 22,000 tonnes/day. Ore mineralization occurs in a shear zone with quartz and native gold. Gold distribution is quite heterogeneous due to the coarse visible gold, in some coarser particles ranging from 100 to 600 microns.Sampling and assaying protocols where established during exploration and prior to starting up operations, based on nomographs developed from early heterogeneity tests. But, as the coarse gold problem became noticeable, it was necessary to develop new sampling protocols to have an acceptable relative standard deviation to control the fundamental error within ± 15%.An experimental program was developed and conducted on a selected ore block made of 195 blastholes; regular ore grade control procedures were applied to both sets of data to evaluate the difference in results between the protocol established prior to starting up operations (“existing”) and the new protocol (“leaching”). In the “existing” protocol, subsampling is done through riffle splitters, and coning and quartering. Fire assaying is used to estimate the gold content, on a 50 g sample. In the “leaching” protocol a 12,000 g sample was bottle rolled cyanide leached, and the leach residue was assayed on a 50 g sample using fire assaying, and a weighted average total gold content was calculated. Currently, a new alternative method is being evaluated, where sub-sampling is done using rotary splitters, and fire assay on a 50 g sample; in this “rotary sampling” protocol and for comparison purposes, gold assays were also repeated using the “leaching” protocol.Test results were compared in three groups < 0.30 g/t (below cut-off), 0.30 to 0.8 g/t, and >0.8 g/t. Overall. Results show that the protocol established prior to starting up operations underestimates the gold assays. Detailed technical results, alternative options, and their implications are discussed in the paper."

Jan 1, 2003

By K. Parameswaran, A. Veek, A. Fernandez, P. Safe

ASARCO LLC (Asarco) Hayden Copper smelter, in Hayden, Arizona, has operated continuously (except for minor labor and economic curtailments) since 1912. The current plant configuration comprises INCO flash smelting, Peirce Smith (P-S) converting and fire refining/anode casting. In order to comply with the U.S. Environmental Protection Agency (EPA) 1-hour National Ambient Air Quality Standards (NAAQS) for sulfur dioxide promulgated in June 2010, the Hayden smelter had to increase overall sulfur fixation from approximately 95 % to 99+ %, requiring a retrofit of the existing converter department and upgrade of associated emissions controls systems. The Converter Retrofit Project (CRP) involved replacing the five existing 13’ diameter Peirce-Smith converters (2 blowing, 2 hot standby) with three new 15’ diameter Peirce- Smith converters (1 blowing, 1 hot standby) to allow for more effective process gas capture using the existing acid plant contact section. Significant upgrades were made to the acid plant wet gas cleaning section and converter primary gas handling system to improve capture performance, reliability, and sludge handling. In addition, a new tertiary gas capture system was installed to further minimize fugitive emissions from the converter aisle. The existing furnace tapping ventilation ESP was replaced with a new baghouse to enable at least 50% SO2 removal using high-surface-area dry lime injection, which was also implemented on the existing converter secondary gas baghouse system. The first two converters and all gas handling system improvements were started up in April 2018, and the third converter was brought online in November 2018. This paper presents the regulatory context; genesis and rationale for CRP; detailed description of the project; challenges during commissioning; system improvements implemented, and design considerations made, and systems performance and process optimization achieved since startup.

Jan 1, 2019

By R. J. Twigg, S. D. Chang

"The production of heavy water, the moderator in a CANDU reactor, is examined following a flow sheet of a typical Canadian plant. The process involves the extraction and concentration of deuterium from natural water through a chemical exchange mechanism with hydrogen sulphide. Consequently, corrosion problems associated with sour environments – the use of hydrogen sulphide - are an everyday problem and have led to the development of a highly refined materials selection and testing program to prevent equipment from failing prematurely.IntroductionHeavy water is a naturally occurring compound in ordinary water and is formed from the combination of two deuterium atoms and one atom of oxygen. Deuterium is a heavy hydrogen atom which has a nucleus of on e proton and one neutron. Hence, heavy water is a combination of heavy hydrogen and oxygen and is chemically known as deuterium oxide. It looks and tastes like ordinary water but it freezes at 3.8°C and boils at 101.4°C. The molecular weight of heavy water is 20 as compared to 18 for ordinary water; the density of heavy water is ten per cent greater than that of ordinary water.Although heavy water and ordinary water exhibit only small differences in their chemical and physical properties, there are large differences in their nuclear properties, the most important of which is the neutron moderating ratio, used to measure the ratio o f the slowing down power to the neutron capture characteristics. For heavy water the ratio is 21000 and for ordinary water it is 50. This high moderating ratio is essential for achieving a high neutron economy. Heavy water is, therefore, chosen as the moderating and heat transport fluid in the CANDU reactor."

Jan 1, 1983

By Chunlin Chen

Published data on thermodynamics of tin in liquid copper, matte and slag have been reviewed, assessed and used in development of thermodynamic solution models of melts. The developed model/database was applied in modelling the Sn deportment in primary copper smelting and e-waste melting processes. The results show that Sn can be removed from the matte through evaporation of various volatile Sn species (with SnS the most volatile) and slagging during copper smelting. The Sn removal increased with increasing matte grade due to the increased gas and slag volume. In the e-waste smelting process, fluxing strategy was developed for smelting e waste to produce a slag with reasonable liquidus and viscosity. Modelling results show that very low amounts of Sn reported to the gas phase due to low S, hence low SnS partial pressure in the system. The black copper produced could contain a few percent of Sn depending on the oxygen potential. The Sn in the black copper could be removed to the slag phase during anode refining. INTRODUCTION Tin is an impurity element commonly found in copper ores, which will be dispersed into various solid, liquid, and gaseous streams during the pyrometallurgical processing of copper. Tin alloy is widely used in electronic soldering due to its low melting point. The growth in treatment of recycled e-waste through primary and secondary copper smelting has led to an increased tin input to the smelting system. Therefore, the deportment of tin between phases is of great interest to the operators of modern smelters. Multi-Phase Equilibrium (MPE) is a thermodynamic package developed by CSIRO for simulating reactions between phases in multi-component and multi-phase systems (Zhang et al., 2002). Over the years the capability of the MPE model has been extended to cover the behavior of a large number of elements in high temperature system (Chen, Zhang, Wright, & Jahanshahi, 2006). In the present paper, the thermodynamic data on tin in liquid copper, matte and slag have been reviewed, assessed and used in the development of a database for Sn slag, alloy and matte phases. The model/database was applied in modelling the tin deportment in primary copper smelting and e-waste smelting processes. The aim of this study is to provide a better understanding of the chemical behaviours of tin in high-temperature copper processing and e-waste smelting.

Jan 1, 2019

By K. Regl, J. Berneder

"AMAG investigated different aspects to improve the resistance against grain coarsening in aerospace alloys during recrystallization and was successful in finding several opportunities to minimize this effect. The studies show that one aspect to counteract grain coarsening is the chemical composition and subsequently all phases that are formed during homogenization. Starting with a fine grain (~ 50 µm) can lead to a final grain size of few mm. On the other hand with a coarse initial grain size (approximately 150 µm) and the right chemical composition the grain size can stay almost constant despite different deformation steps. Additional we investigated different sequences for the component production to eliminate the problem of grain coarsening as a coarse grain has a detrimental effect on product performance.INTRODUCTION In the aircraft industry, aluminium sheets are most commonly deformed in their soft state, followed by solution heat treatment and natural or artificial aging. If the preceding deformation is in a critical amount, during the recrystallization at solution heat treatment grain coarsening can occur. A subsequent deformation to this condition leads to an orange peel surface, which requires additional polishing. Next to this extra effort the coarse grain size produces a drop in the mechanical properties, often below specification limits. If there is no subsequent deformation, this effect is not visible and without destructive testing there is no possibility to detect the error. As mentioned before, this effect occurs during recrystallization, which is a process that is driven by the stored energy in the microstructure. The two most important aspects for an increase of the stored energy are the increase of the grain boundaries fraction (smaller grain size) and the increase of the dislocation density caused by deformation. The increase in dislocation density during the deformation arise from trapping of existing dislocations and from the generation of new dislocations. During recrystallization all grains are built completely new, so all dislocations are removed (Humphreys & Hatherly, 2004). There are three requirements for recrystallization:"

Jan 1, 2018

By T. R. Chari

The safe-level dilution of low-level radioactive wastes in large volumes of selected granular material is proposed as an alternative method of permanent waste disposal to current Canadian practice of concentration and encapsulation. Accepting the fact that a "background level" of radioactivity exists throughout the world, the authors feel that the concept of controlled dilution of radioactive wastes to a level in keeping with "background" is a plausible alternative to current thinking on the subject and is worthy of equal consideration.

Jan 1, 1979

By Michael S. Moats, Addin Pranowo, Gerardo R. F. Alvear F., Nigel Aslin

The toxicity of arsenic is well known and documented. However, the presence of arsenic in copper electrorefining anodes and electrolyte is critically necessary to produce high quality cathode. Arsenic as well as antimony and bismuth concentrations vary depending on their relative concentration in the anode copper received from the smelter. This paper will discuss the behaviour and benefits of arsenic in copper electrorefining and the detrimental effects of antimony and bismuth on cathode quality and tankhouse performance. This will include the minimization and mitigation of problems associated with arsenic, antimony and bismuth including cathode contamination, floating slimes, scaling and anode passivation.

Jan 1, 2014

By Tom Setterfield

Conclusions ?Canada is a prospective place to explore for IOCG deposits ?Time distribution of IOCG mineralization in Canada mimics that in the rest of the world ?Canada may have been the first country to start mining IOCG deposits ?Production from newly discovered IOCG deposits in Canada may start soon

May 1, 2006

By M. Sabau

The Electrowinning Plant at INCO&apos;s Copper Cliff Nickel Refinery is a precious metals upgrading plant. The feed to the plant contains copper, nickel, cobalt, iron, significant amounts of precious metals and some impurities. Copper is the most abundant element in the feed. This paper describes the major equipment and process changes over the last twenty years, geared to improve the tankhouse operation, workroom environment and recovery of copper from the acidic solution. Copper is plated on to titanium blanks using explosion-bonded crossrods, animal glue as a levelling agent, and an organic surfactant for mist control. The installation of the stripping machine in 2001 required a number of changes: cathode and anode contacts were redesigned, flat bus bars were replaced with dog-bone type, spacer boards for cathodes and anodes were installed, longer anodes started to be used, and the plating cycle was extended from seven to fourteen days. A number of initiatives for improvement are being carried out. Explosion-bonded crossrods are being replaced with titanium-clad crossrods. The plan for the near future is to increase copper production by increasing current efficiency and current density. The possibility of lowering the iron concentration in electrolyte and changing the acid mist control method is being investigated.

Jan 1, 2007

By Kosuke Hosoda, Shuji Owada, Hiroyuki Tokuichi, Hirobumi Ohta, Chiharu Tokoro, Moto-o Sato, Katsushi Okumura, Hiroto Ogawa, Hideaki Umezawa

The Japanese government enforced the "Small Domestic Appliances (SDAs) Recycling Law" in 2013. The law targets metals such as Ta, Nd, Dy, Co, and W to be recycled. Considerable amounts of these minor rare metals are mounted on printed circuit boards (PCBs) of the SDAs and/or e-scrap (electric and electronic scraps). Although precious metals and copper can be recovered from the e-scrap in non-ferrous metals smelters, most of the minor rare metals report to the slag in these smelters in non-recoverable forms. These metals are often used in particular types of devices, and therefore it is possible to concentrate them by separating such devices before feeding to the smelters. In previous work we developed technology for "Device Separation" to concentrate several minor rare metals, but some problems remained, such as how to remove the PCBs from e-scrap bodies, and how to detach devices from PCBs after their removal from escrap bodies. This paper proposes a two-stage crushing process in which, firstly, PCBs are removed from the e-scrap body with various crushers, and secondly, devices are detached from the PCBs involving the application of elevated temperatures. It was found that in the first stage, crushers with physically flexible rotating media such as chains, which provide high collision probability with the sample and consume relatively low energy, can quite effectively separate the PCBs from the e-scrap bodies non-destructively. In the second stage, heating was found to be remarkably effective in helping to detach mounted devices from PCBs, also non-destructively. This paper will also discuss the detailed mechanism of the heating effect on the detachment of devices from PCBs.

Jan 1, 2014

By R. St. C., G. E. Morris, M. Zbik, Smart

Effective flocculation and dewatering of slurry streams containing clays (particularly kaolin and smectites which are often <200nm in lateral dimension) is becoming increasingly urgent. Release of water (often >75 wt%), for recycle and reduced make-up water consumption, from slurries in tailings streams and dam beds is usually slow and incomplete. Changes in settling rates and solids density of tailings containing clays can be achieved in practice by changes in pH, dissolved cations and flocculant additions. To achieve fast separation of clays from water and minimization of retained water, individual particles need to be bound in the initial stages of thickening into large, high-density aggregates, which may sediment more rapidly with lower intra-aggregate water content. Quantitative STIMAN (STructural IMage ANalysis) cryo-SEM imaging, shows that the structure of aggregates formed before flocculant addition has a determinative effect on these outcomes. Without flocculant addition, 4 stages occur in the mechanism of primary dewatering of kaolinite: initially separate particles and aggregates are dispersed (<0.3GP, where GP is the gel point); a partially-gelled chain network then forms linking particles edge-edge (EE) still well below the OP but remains largely suspended; after an induction time, this network structure rearranges from EE to face-face (FF) contacts densifying, compacting and dewatering the aggregates with settling rates well above Stoke&apos;s Law estimates for >20µm particles or aggregates; the GP is rapidly reached during settling producing a network spanning the vessel with compressive strength. This sponge-like structure with EE oriented particles limits slurry dewatering because the steric effect in the resulting partially-gelled structure is much more dominant than the electrostatic effects predicted by DLVO theory. Van der Waal&apos;s forces at very close distances, as particles slide across each other, may be responsible for the EE to FF change in structure. In this way, the previously extended network contracts, and when the solid volume fraction is low, the continuous network breaks apart forming aggregates and aggregate associations as flocs which arc able to freely settle. These densified aggregates settle at increased rate, give lower bed density and retain less water after drainage. With flocculant addition, the internal structure and networking of the pre-aggregates is largely preserved but they are rapidly and effectively bound together by the bridging action of the flocculant(s). The STIMAN analysis shows that there is a inverse correlation of intra-aggregate porosity (and void permeability) with Darcian permeability (and extent of dewatering) whereas there is a strong positive correlation of Darcian inter-aggregate permeability with settling and primary dewatering rate.

Jan 1, 2004

By Nicola Robjohns, Kenneth A. Grace, Jane Spooner

"The important volume end use sectors for the rare earth elements and yttrium continue to be in steelmaking, petroleum cracking catalysts and glass polishing. The market sectors which may provide future high volume demand, to replace the older sectors where demand has declined over the past decade, include magnets, automobile catalysts, ceramics and superconductors. Increases in production capacity in all major rare earth producing countries are expected to restrain large price increases for high purity rare earth oxides over the short term. A sharp increase in demand for yttrium in advanced ceramics and superconductors would lead to a shortage in separation capacity, however, and to a corresponding rise in prices for separated rare earths.IntroductionWhile visiting the Geology Department of the University of Toronto in 1981, Professor Lu from the Institute of Geochemistry of Academia Sinica at Gweiyang in China introduced one of his seminars with the observation that in China, rare earths are not rare at all.Indeed, while being rare in terms of abundance as measured by, say, the Clarke scale, the rare earth elements, like many other low abundance elements, are subject to geological, geochemical and mineralogical concentration.The rare earth elements comprise the fifteen inner transition elements of Group IIIB, Period 6, of the periodic table, from lanthanum to lutetium (the lanthanides), as set out in Table 1. The rare earths constitute a distinct group as they have extremely similar chemical characteristics due to the uniformity of their outer electron shells. The element yttrium is usually, by convention, included in the rare earth group as it occurs with the rare earths in nature and has properties very similar to them.The rare earths are divided into two subgroups, the ""light"" rare earths, made up of the first seven elements of the series, lanthanum to europium, and the ""heavy"" rare earths, comprising the remaining eight elements, gadolinium to lutetium, plus yttrium. These two subgroups are also referred to as the cerium subgroup and the yttrium subgroup, respectively. The subdivision is based on differences in the atomic radii resulting in somewhat different properties for the two subgroups."

Jan 1, 1991

By Jonathan Peck, Jim Gray

"With the implementation of more advanced monitoring, control and locating systems in surface mines, there is an ever increasing need for their mine-wide integration toward achieving over-all optimization. AQUILA Mining Systems Ltd. is developing the basis for a comprehensive real-time monitoring, control and information system called the Total Mining System or TMS. This system is being designed to address both current and future needs of open pit mines toward improving productivity and minimizing costs, through better two-way information flow between each component in the operation. At a basic level, feedback from equipment and process monitoring will enable decision making to be based on quantitative, on-demand information, thus permitting proactive rather than reactive planning. Dynamic planning would be a valuable tool as market conditions fluctuate, equipment fleets age and variations in the grade, quality, geometry and hardness of the mined material all contribute to either changing production targets or levels of achievable performance. Such a capability could be implemented within the next two years.At a higher level, and within five years, autonomous operation and/or real-time supervisory control of mobile and stationary equipment in open pit mines will be achieved. A discussion is provided in regard to the development and implementation of an autonomous haultruck and blasthole drill, to demonstrate the need for such a system.This paper outlines a preliminary program for the design, development and implementation of this system, primarily in relation to high-level communications and its role in the future automation of open pit mobile equipment."

Jan 1, 1995