Search Documents

By Brad Marchant, Rick Lawrence, David Kratochvil

"BioteQ has successfully developed commercial operations for ARD treatment and selective metal recovery using the patented BioSulphide and Thiopaq® biological reduction technologies. The BioSulphide-Thiopaq process was developed to provide biogenic sulphide for the selective recovery of high purity metal concentrates from acidic wastewater, which are sold to recover capital costs and off-set water treatment costs. The BioSulphide-Thiopaq process can be used on a stand-alone basis or in conjunction with a lime circuit. Process advantages include: selective recovery of metals, very low metal concentrations in effluent, reduced waste sludge liability, reduced lime treatment costs and, in some cases, profitable sale of metal concentrates. Two case studies are presented to illustrate operations focused on metal recovery at the Caribou Mine, New Brunswick, Canada, and at Phelps Dodge, Arizona. A third case study is presented to highlight environmental control as well as metal recovery for treatment of ARD at the Raglan Mine in Northern Quebec. Process flowsheets, capital and operating costs are presented for the three case studies.INTRODUCTIONProtection of water quality has become one of the most important environmental challenges facing the mining industry. Although new mining projects can be designed to minimize impacts to the environment, many existing and abandoned mining operations have water quality problems. The principal cause of water contamination is acid rock drainage (ARD), which is generated when residual sulphide minerals in waste rock, tailings and other mine components and products are exposed to air and water. These reactions can produce acidity and elevated concentrations of metals in drainage and seepage that can adversely affect surface and groundwater resources. To meet regulatory criteria for water quality in the receiving environment, many mine operators must consider treatment of mine water and other effluents prior to discharge."

Jan 1, 2003

By Masami Nakamoto

Controlled thermolysis of gold(I) thiolate complex, [C14H29(CH3)3N][Au(SC12H25)2], at 180 °C for 5 h under an N2 atmosphere produces novel gold nanoparticles passivated by alkyl groups derived from the precursor complex, the TEM photograph of which shows spherical particles with average diameter 26 nm. Since Brust et al. reported the two-phase reduction of AuCl4 - by NaBH4 to afford monodispersed gold nanoparticles passivated by alkanethiolate ligands (1), plenty of preparative investigations on gold nanoparticles (2,3) and its surface modification (3,4) have appeared, because of their potential applications in microelectronics (5). However, those preparative methods generally involve the reduction of AuCl4 - by reducing agent NaBH4 in the presence of suitable organic stabilizers such as alkanethiol (1-4), phosphane (5), quarternary ammonium salts (6), surfactants (7) or polymers (8). On the other hand, O?Brien et al. recently reported the preparation of organically capped gold nanoparticles at 190 °C, where tri-n-octylphosphine oxide and/or n-octadecylamine are used both as a reaction medium and as a passivating ligand (6), but this procedure also needs NaBH4 as reducing agent. Our strategy of novel preparative method of gold nanoparticles is the combination of reductive elimination of thiolate ligands and simultaneous attachment of organic moiety on the growing nuclei. Gold(I) thiolate complexes with ammonium cations were useful for our preparative method. We now report the controlled thermolysis of gold(I) thiolate complexes, [R(CH3)3N][Au(SC12H25)2] and [R(CH3)3N][Au(SC6H4-p-R?)2] (R= C14H29, C12H25; R?= C8H17, CH3), under an N2 atmosphere, where the powder of gold(I) thiolate complexes completely melts to afford the precursor liquid and then the liquid gradually decomposes. In spite of no use of reducing agent and solvent, reduction reaction is thermochemically induced to afford novel gold nanoparticles passivated by alkyl groups rather than by alkanethiolate ligands. Figure 1a shows a typical transmission electron microscopy (TEM) image of gold nanoparticles prepared by thermolysis of [C14H29(CH3)3N][Au(SC12H25)2] at 180 °C for 5 h, indicating a controlled growth of spherical gold nanoparticles. As shown in Fig. 1b, these spherical gold nanoparticles display the size distribution ranging from 5 to 50 nm. Although the particle size is larger than that of thiol-derivatized gold nanoparticles (less than 5 nm) prepared by NaBH4 reduction (1-3), the aggregation of gold nuclei is smoothly regulated and the growth of core gold is limited to be 26 nm in average diameter in spite of thermal procedure.

Oct 1, 2003

By P. Homola, M. Karlík, M. Slámová

"Aluminum sheets (AA1199, AA8006, and AA5754) were processed by accumulative roll-bonding (ARB) in the temperature range from 20 to 350°C. The microstructure of the sheets was characterized by means of scanning and transmission electron microscopy and electron backscattered diffraction. Mechanical properties were monitored by hardness measurements and tensile tests. Increasing strain (number of ARB cycles) led to incremental development of lamellar microstructure with a decrease of the spacing between high-angle grain boundaries in the normal direction of sheets. ARB process produced an important increase of strength while maintaining thickness and relatively high ductility, without accenting of the anisotropy of mechanical properties of sheets. The level of hardening decreased with the processing temperature and at 300 and 350°C ARB caused even the softening of the material due to the recovery of the deformed microstructure or partial recrystallization during heating to ARB processing temperature.INTRODUCTION Accumulative Roll Bonding (ARB) is a technique of grain refinement by severe plastic deformation (SPD) proposed by Saito et al. (1999). One ARB cycle consists in sheet cutting, surface treatment, stacking of two pieces, heating (optional), and rolling with 50% reduction in thickness. Since the sheet thickness remains unchanged by this cycle, ARB processing can be repeated as many times as desired. The goal of ARB is to impose an extremely high plastic strain on the material, resulting in structural refinement and strength increase without changing specimen dimensions. After several cycles, ultra-fine grained (UFG) materials with high strength and relatively high ductility are produced. An advantage of this method is that it does not require any special equipment as other SPD methods such as equal channel angular pressing (ECAP) (Valiev & Langdon, 2006), high pressure torsion (HPT) (Valiev et al., 2000), or cyclic extrusion and compression (CEC) (Richert et al., 1999), but only a conventional rolling mill and so it is seen as an economically viable and industrially scalable processing route. ARB processing has been successfully applied to various kinds of metallic materials at room or elevated temperatures (Tsuji, 2005). Besides processing single metals and alloys, ARB has also been used for creating ultra-fine grained and nanograined metallic composites (Wu et al., 2010; Qu et al., 2014)."

Jan 1, 2018

By A. B. Luz, A. Middea

Kaolin clay is heavily used in the paper industry as a coating and a filler, however to attend the specifications required by the industry it has to be processed. Kaolin is also used as a filler and pigment in various materials, such as paint, plastic, rubber etc. Some crude kaolins as mined in Northern Brazil, contain colored impurities such as iron oxide and rutile/anatase. These minerals normally are stained by iron and as a result vary from yellow to dark brown in color. The kaolin beneficiation process used in that region consists mainly of degritting, fractionation by centrifuge, high gradient magnetic separation, bleaching with sodium dithionite, filtering and drying. In some kaolin clays from that region, titanium oxide mineral occurs in fine fraction, lower than 2 µm, and so making the industrial process more difficult. The conventional method of classification and bleaching with sodium dithionite, markedly improves kaolin brightness, but has little effect on anatase removal. In fact, the fine fractions resulting from centrifugation, in many cases contain more TiO2 minerals than the original whole clay or the coarse fraction. The present work is related to purification of Brasilian kaolin clay using selective flocculation for removing its colored impurities such as rutile and anatase. This study was conducted in bench scale and it consisted of: blunging, screening, conditioning and decantation. Overflow and underflow resulting from settling of the flocculated material were then dried and submitted to TiO2 and brightness analyses. Sodium polyacrylate and sodium silicate were added to kaolin clay suspension as dispersant and ammonium hydroxide was also added to adjust pH. After degritting, the minus 44 µm fraction was conditioned with hydroxamate surfactant and then polymers of different anionic charge were added. The influence of pH and type of polymer on efficiency of TiO2 removal, as well as kaolin mass recovery were studied. The results obtained in the present study are quite promising. It was possible to diminish TiO2 content and increase kaolin brightness (ISO) from 82 to 88%.

Jan 1, 2004

By Barry Hope, Javier Rico

"Goldcorp’s Hoyle Pond mine has recently completed several projects which have impacted the overall ventilation system. The project includes extending the Fresh Air Raise (FAR) to depth, development of a new Return Air Raise (RAR), and the installation of new sensors and ventilation controls throughout the mine. Two years after the completion of #2 Winze, the mine is ramping up its ore production to 1,300 tpd (up from 1,100). To ensure safe and profitable production, a reliance upon technology has been needed to provide the required ventilation to the work areas according to the mine plan. To systematically assess the mine’s ventilation in real-time, a significant increase in remote monitoring was required. This included installing additional flow, pressure, temperature and gas sensors. The first step in upgrading the existing monitoring was to purchase airflow and differential pressure monitors and install them in key areas of the mine. This paper presents the process of expanding the monitoring capability at Hoyle Pond mine, the selected equipment and the results of the implementation. The intended goal was to improve safety while minimizing capital and operation costs. The monitors were installed in strategic locations to provide immediate feedback on the impact of changes to the primary ventilation airflows. Comparing the available sensor technologies, installing them and systematically monitoring the ventilation served as a first step towards developing a mine wide Ventilation Control System. In addition, the initial state of the monitoring and control system, with final results and the chosen solution for the mine site, are presented. INTRODUCTION The Hoyle Pond mine is located in the City of Timmins, within the Porcupine mining district, Ontario, which has produced more than 70 million ounces of gold since 1910. Currently, approximately 60% of Porcupine Gold Mines gold production comes from the Hoyle Pond underground mine. Mechanized cut and fill and long-hole mining methods are used to extract the ore. The remainder of the ore comes from the Hollinger Open Pit mine. The Dome Underground mine ceased operations in 2017. Hoyle Pond is currently mining at 1820 meters below the surface and plans to go deeper. The average dry-bulb as wet-bulb temperature underground varies according to the depth and surface conditions which has extremes of –40°C in winter to +30°C in summer. The total airflow volume pushed down from surface is 240 m3/s to accommodate the diesel-powered equipment needed for normal operations. In order to improve the quality of air underground a program has been implemented to use diesel particulate filters, starting with the truck fleet and 6-yard scoops, followed by the intention to implement the rest of the functional diesel-powered equipment and eventually move to electric equipment."

Jan 1, 2019

By Alan F. Stewart, Frederic B. Claridge, Robert S. Nichols

"In recent years, an increasing number of mines in mountainous terrain have examined the possibility of placing mine waste rock into stream valleys. Pressure to utilize stream valleys as a primary location for waste disposal has increased at many of the mines currently under development or expansion. As the number of environmentally and economically ideal wastedumping sites is limited, consideration must be given to utilization of stream valleys. This raises concerns about maintaining water quality in streams passing through or beneath the dumps and potential detrimental effects to dump stability. Commonly, the flows in the streams tend to be flashy, reflecting localized intense storms and rapid runoff in steep-sided slopes within the watershed. These conditions pertain particularly to British Columbia, which is characterized by mountainous terrain and periodically intense precipitation events.The method of conveying flow through a waste dump depends on a number of geotechnical and hydrological factors, including the size, durability and transmissivity of the rock and the design stream flood flow. This paper describes the approach to the design of waste dumps in stream valfeys developed at several mines in British Columbia."

Jan 1, 1986

By I. S. Parrish

The Sullivan Mining Group has been exploring the mineral deposits of the Mount Pleasant area of southern New Brunswick since 1967. Sullivan geologists have logged over sixty miles of drill core, mapped over five miles of underground workings and studied numerous surface exposures. Several mineralized zones have been defined and two higher-grade porphyrytungsten bodies delineated. Within these bodies, wolframite occurs as disseminated specks and grains up to one-half inch in diameter. The host rock is a brecciated rhyolite porphyry that has intruded quartz-feldspar porphyry of Mississippian age . The host rock is itself intruded by an acid porphyry called transition rock and is underlain by a microgranite. The mineralized zones, host rock, transition rock and microgranite are all thought to be derived from the same magma, and to represent progressive fractions from that magma.

Jan 1, 1978

By Jeff Smith

Agenda About NORTHPARKES The NEED The INITIATIVE The SEARCH The PRODUCTS The SOLUTION The RESULTS The Northparkes copper-gold mine in Central Western NSW commenced operations in 1994. Copper concentrate is produced and shipped to smelters in Japan, China & India under long term contracts with spot sales to other Asian countries.

May 1, 2006

By S. Espley, G. Tan

"Inco's Little Stobie Mine is a low-grade nickel operation producing approximately 4()()() tons per day. Backfill has never been an economical option at the mine; therefore, the only viable type of mining in the upper zones has been by sub-level cave. This mining method allows for the draw-down of a rock cover into the empty stopes to provide stability to the over-all rock mass. In the lower areas of the mine, bulk blasthole mining methods have taken place, without rock fill, resulting in extremely large open stopes. As the mine reaches its final stage of recovery, it is inevitable that the hangingwall of the large voids will undergo tensile failure via spoiling.This paper deals with the collaborating efforts of Inco's Rock Mechanics group and the Little Stobie mining operations toward the successful recovery of the ore zone remnants such that the inevitable failure, and time of failure, of the rock mass is ""controlled"". Within the mining scheme, several key requirements had to be met to satisfy the operations: (1) production rates; (2) good blast fragmentation; and (3) secure pulling-horizons. A full-scale rock mechanics study was carried out involving: numerical modelling studies; pulling ellipse analyses; blast design, monitoring and analyses; laser profiling; and time domain rej7ectometry (TDR) instrumentation. The final recovery scheme, employing a controlled failure, involves recommendations on: (1) blasting techniques; (2) support systems; (3) mining sequences and scenarios; and (4) monitoring systems."

Jan 1, 1994

By M. Dosoudil

"Continuous pressure filtration is a modern process for the mechanical dewatering of flotation concentrates of coal and similar coal slurries. This method will give a lower moisture content than classical vacuum filtration, the improvement lying in the range 5% to 15%. Eighteen coal slurries have been examined in this survey. They are representative of a wide spectrum of filtered slurries. IntroductionDuring the last five years, a number of coal slurries have been tested either in the laboratory or with a pilot plant. The test pressure ranged from one to six bar. The results have been evaluated by mean s of a computer. Determination of the filter capacity and the resulting moisture content and energy consumption has been made with respect to the continuous pressure filter, Amafilter construction-type KDF (Fig. I) . Standard sizes of these filters are 60 m2, 90 m2 and 120 m2.The continuous pressure filter is a horizontal filter with a level tank. Six filter axles are mounted on a rotating main shaft, each with a particular number of elements attached. The elements rotate on their axes and move along a circular trajectory. Periodically the elements submerge into and emerge out of the slurry. A constant air pressure is maintained above the suspension, thus providing the pressure gradient necessary for filtration. The filtrate together with the dewatering air flows through the elements into the hollow axle and out of the filter."

Jan 1, 1987

By G. P. Cooper

A comprehensive computational heap leach model was used to evaluate options for operating a chalcocite-ore heap leach process. The stockpile leach model is based on the computational fluid dynamic software framework PHYSICA+ and incorporates various physical and chemical phenomena to simulate fluid transport, mineral reaction kinetics, bacterial effects, and heat, energy and acid balances for the overall leach process. The leach model is calibrated against small-scale column leach tests, and simulation results are validated against closely controlled column pilot-scale tests. For a given set of ore conditions, the effects of raffinate irrigation rate are examined. Several options for pulse leaching were investigated, and the effects on copper recovery and pregnant leach solution (PLS) grade are described. Model simulations indicated that pulse leaching could be used to control copper grade of the PLS. Finally, an analysis of inventory issues is presented for various lift heights including multi-lift simulations to examine potential operating options. U sing irrigation rate, raffinate copper grade, and lift height as variables in a factorial design of experiments, the simulations showed that raffinate copper grade is the main factor that affects the soluble copper inventory grade.

Jan 1, 2007

By B. Qiu

The large surface ground movements induced by underground mining could threaten the safety of the pipelines laid across the subsidence-prone area. Existing analytical methods for the stress analysis of buried pipeline over mine subsidence area were based on the assumption of ?thin? pipeline, which limited their applicability. This paper presents the improved model with the capability to determine the stress distribution of the ?thick? pipeline. The pipe-soil interaction in this model was also updated to adapt various pipe soil contact conditions. In addition, the time-dependent effects of dynamic subsidence effects were also added to the model. A case of protecting a long section of a buried large-diameter pipeline over two longwall panels in a shallow mine is shown. The stress distribution along the pipeline is determined and the overstressed sections are identified. A partial uncovering plan was developed based on the predicted stress and complicated terrain at the site.

Aug 1, 2013

The 14MW SAG mill at Tarkwa, Ghana, experienced a frozen drop charge incident on 10 February 2010. This caused downtime of 112 hours, a repair cost of $200k and production loss of 162,000 tons, corresponding to a loss of $8.9M. A new locked charge protection system was installed on the two Tarkwa mills on 30 July 2010, mitigating this risk. This system calculates the ore angle in real time while the mill is starting up and trips the mill if the ore angle exceeds a trip angle setting. The calculation of the ore angle is derived from the mill motor rotor currents only - no mechanical transducers are required. The head of Gold Fields West Africa, Peter Turner, says of the new system: "This is excellent work and the type of technology that has had and will continue to have, major opportunity cost impacts on our business."

Jan 1, 2012

By N. Schreithofer, M. Aspiala, R. Serna

The novel attachment timer apparatus presented in this paper serves as a diagnostic tool that allows the detection of changes in bubble-particle attachment probability and therefore floatability caused by alterations in the chemical environment and particle properties. The apparatus consists of six identical capillaries where bubbles with defined size are produced simultaneously in a measurement chamber. The bubbles at the capillary tips are placed in contact with the submerged particle bed for specific time periods, controlled with the help of automatic actuators. The advantage of the instrument is that hundreds of bubble-particle contacts can be measured automatically within a short time period. Microscopic pictures of each measured bubble are taken while recording the movement of the bubble before, during and after contact with the solid particles. The recorded pictures can be used to determine the actual bubble size and its corresponding deviation, and to detect the attachment of particles. The attached particles are collected in a detachable chamber for subsequent characterization. Furthermore, the device is portable and can be taken to the mineral processing plants for quick evaluation of particle-bubble attachment efficiency with particles and process water sampled directly from real processes.

Jan 1, 2017

By Tom Shumka

INTRODUCTION ?This bull gear inspection technique was developed to provide more accurate data and faster inspection times than current techniques used today. ?Eddy Current Array (ECA) is a non-destructive testing technique that provides the ability to electronically drive multiple eddy current coils, which are placed side by side in the same probe assembly. Each individual eddy current coil in the probe produces a signal relative to the phase and amplitude of the structure below it. ?This data is referenced to an encoded position and time and represented graphically as a C-scan image. Most conventional eddy current flaw detection techniques can be reproduced with ECA inspections; however, the remarkable advantages of ECA technology allow improved inspection capabilities and significant time-savings.

Oct 1, 2010

By Kazuhide Nakaniwa

In this research, we devised a measurement method using total stations (TSs) which have ?the Baum? which is a concentric circle reticle, as substitute for crosshairs. The Baum owes its name to the similarity between the concentric circles and trees (Baum in German). By setting one circle on both of edges of cylinders, operators can set their sights on points on the center line of the cylinders, and also can measure positional coordinates of the points. Also, by measuring two different points on the center line, operators can measure the position and tilt of the axes of the cylinders. Furthermore, we developed a pile driving navigation system. Foundation piles are used for various structures, and their forms are generally cylindrical. Especially, although it is difficult to drive tilted pile foundations, their usage are expected to expand due to their high earthquake resistance. Yet, a method to accurately measure the tilts of piles has not been established. However, we proved that operators can obtain adequate accuracy to control foundation piles through the measurement experiment using this system. Using this system, the information of the pile is measured using a TS, transferred to a PDA, and displayed from the operator?s view of the piling machine.

Aug 1, 2013

By D. Lascelles, J. A. Finch, E. El-Ammouri

Flotation separation is expected to be related to the degree of dispersion of the pulp. For instance, highly aggregated systems may show reduced selectivity, reduced entrainment and increased flotation rate. In an attempt to test the impact of aggregation on flotation, we have taken advantage of the effect of Mg ions. Using combinations of Mg2+ and pH gave a wide variation in aggregation of several Cu-Zn ores (measured by settling rate) and corresponding flotation response was determined by batch tests. The trials were conducted on-site at Louvicourt and Agnico-Eagle. In a majority of cases a similar trend in aggregation and flotation selectivity (grade at given recovery) was observed. At Louvicourt, improved selectivity with increasing aggregation at pH 10.5 was found. At Agnico-Eagle, an analogous association between aggregation and selectivity was observed at pH 11.5. It is suggested that aggregation influences particle entrainment, the increased effective particle size reducing gangue recovery and hence improving selectivity.

Jan 1, 2004

By Richard Dawson

Increasing global demand for coking coal has initiated several new coal mine developments in northeast BC. These developments are able to take advantage of the currently under utilized infrastructure that was put in place during the 1970?s and 1980?s for the Quintette and Bullmoose coal mines; which includes the Town of Tumbler Ridge, a 1,000km rail line to the coal terminal at Prince Rupert and a road system providing highway access to the town site. Coal within the two foothills regions of BC (north-east and south-east) is mined by open pit truck/shovel methods. Optimized mine plans require a thorough understanding of Rocky Mountain structural geology, attention for access in steep terrain, and a related understanding of the geotechnical conditions that control the stability of pit slopes and waste dumps. Thus there is a requirement to properly integrate mine planning with geotechnical engineering considerations. Many of the technical issues are well understood from experience during the past 30 years of Western Canadian coal mining. The challenge is to ensure that the mine plans are able to take full advantage of these lessons learned. The paper will focus on mine planning and geotechnical design issues to do with high angle-of-repose waste dumps and steeply bedded footwall slopes to illustrate the advantage of properly recognizing the important stability control issues during the early stages of engineering evaluations. Case histories from the existing and planned coal mining operations will be presented.

May 1, 2006

By J. Keough

During industrial electrowinning of copper, uneven growth can impact current efficiency, cause short-circuits in the cell and negatively impact the final quality of the metal product. Copper electrodeposits can be made smoother by incorporating a host of additives in the electrolyte but uneven copper growth may still occur due to variations in electrolyte composition throughout the cell-house. To quantify roughness, 3D images of the surface may be combined with scaling analysis to gain further insight into the deposit structure. Moreover, scaling analysis may offer a method to predict long-term deposit structure using short-term copper deposits. In this paper, the application of Atomic Force Microscopy (AFM) and scaling analysis are used to monitor copper growth and extract surface roughness characteristics. The cathode was a 304 stainless steel disc that was polished to a mirror finish. Copper was deposited onto this surface over a range of 10, 20 and 30 minutes from an acidic sulfate solution (40 g/L Cu) at 40oC from an electrolyte that contained or was free of guar. AFM images were acquired to obtain 3D topographical information on the samples and scaling analysis was performed to extract the root-mean-squared (rms) roughness, periodicity (grain size), aspect ratio of surface features and growth mechanism. INTRODUCTION During the process of copper electrowinning, the dissolved metal ions are reduced and thereby deposited onto a cathode substrate which is later recovered by stripping the metal from the cathode surface. Although this process is widely used in the industry, the conditions of the deposition procedure may cause the growth of the metal product to be uneven which can not only impact the current efficiency and final copper product quality but may also lead to plant interruptions through short-circuits if the anode and cathode make contact. To create more uniform copper deposits, a host of additives may be included in the electrolyte which may act as brighteners, leveling agents and inhibitors which may include guar gum, glue, thiourea or polysaccharides or polyacrylamides and their industrial use has changed over time (Moats, Luyima, & Cui, 2015). As such, the electrolyte composition is often complex and subtle variations in the solution matrix throughout the cell-house may impact the surface morphology of the final copper product. In an effort to quantify the roughness of copper samples, image analysis is often applied and may include Scanning Electron Microscopy (SEM) or Atomic Force Microscopy characterization. While both are appropriate, AFM offers 3-dimensional information which may be used to both qualitatively and quantitatively characterize the surface characteristics.

Jan 1, 2019

By D. G. Dixon

A novel technology for leaching copper from primary copper concentrates has been developed at UBC. This patented technology takes advantage of the galvanic couple between pyrite and chalcopyrite to ensure rapid and complete oxidation of chalcopyrite under mild conditions in acidic iron sulfate solution, without the need for microbes, ultrafine grinding, or chemical additives such as chloride, nitrate, or surfactants. Copper recoveries of 98% or greater can be achieved at 80°C under atmospheric conditions in as little as 4 hours of residence time. The process is selective for chalcopyrite over pyrite, generates near-quantitative levels of elemental sulfur, and is fully compatible with conventional solvent extraction and electrowinning of LME Grade A copper cathodes. In this paper, the fundamentals of the Galvanox ? process are reviewed, and selected results of batch leaching tests on various concentrate samples are presented and discussed.

Jan 1, 2007