Search Documents

By N. Aslin, G. Heferen, H. DeWaal

"Mount Isa Mines (MIM) acquired a reputation for the successful application of R&D to develop break-through technologies for the mining industry starting in the 1978’s through until the early 2000’s. The ISAPROCESSTM tank-house technology has been licensed to copper refineries throughout the world, and a significant per cent of the world’s copper is refined using this technology. Since development in the late 1980’s more than 20 ISASMELTTM copper and lead smelting furnaces are now installed in countries around the world. Jameson Cell flotation technology developed jointly by Mount Isa Mines and Professor Graeme Jameson is widely used in the Australian coal mining industry and increasingly in the base-metal and gold industry. The IsaMillTM’s developed at Mount Isa and McArthur River made it possible to develop the McArthur River and George Fisher orebodies and has been successfully implemented into base metal fine grinding applications around the world. The most recent commercialised innovation is the atmospheric leach Albion ProcessTM with its supersonic HyperSpargeTM gas sparger, is being adopted as a solution to the increasing complexity of orebodies. MIM’s contribution to the industry was significant given the size and the remote location of its operations with Townsville Copper Refineries more than 1350 km and Mount Isa 1800 km from the nearest state capital of Brisbane. This paper will briefly discuss the development of each of these technologies and why MIM – now owned by Glencore - was so successful innovating and developing such technologies over a period of nearly 40 years.INTRODUCTION Mount Isa is located in the Gulf Country region of Queensland about 1800 kilometers North West of Brisbane (see Figure 1). It came into existence because of the world class mineral deposits found in the area. In 1923 the orebody containing lead, zinc and silver was discovered by the miner John Campbell Miles. Mount Isa Mines Limited (MIM) was founded in 1924 to develop the minerals discovered by Miles, but production did not begin until May 1931. It paid its first dividend in 1947 after 16 years of troubled production. In 1954 the 1100 copper orebody was discovered and with rapidly rising reserves during the 1950’s and 1960’s led to the construction of new concentrators to treat lead/zinc/silver ores in 1966 (#2 concentrator) and copper ore’s in 1973 (#4 concentrator). The difficult nature of the Mount Isa lead-zinc orebodies has meant that the company had always needed to be at the forefront of mining technology. In the 1970’s through to the 1990’s, it became a world leader in developing new mining techniques and processing technologies as a response to declining metal prices and rising costs. Mount Isa has been smelting copper since 1953 and lead since the early 1930’s. Copper Refining at Mount Isa’s fully owned subsidiary of Copper Refineries Proprietary Limited (CRL) had commenced operations in 1959."

Jan 1, 2018

By T. Holmes, S. Davison

"A surge bin at Agrium’s Vanscoy potash operations has been plagued with flow, wear, and corrosion issues since being built in 1967. The culprits? The bin’s carbon-steel construction, geometry, and the resultant funnel-flow pattern are the root causes. An investigation and cost analysis indicated that hopper redesign and retrofit would increase production and reduce maintenance and capital costs. The retrofitted bin provides safer, more reliable operation and has a much longer predicted working life. Using this example, the authors describe bulk-solids-flow theory and highlight the importance of customizing bulk-material-handling-system design using appropriate flow properties to improve reliability, safety, and cost effectiveness.RÉSUMÉ Depuis sa construction en 1967, un réservoir intermédiaire de l’exploitation de potasse Vanscoy d’Agrium connaît des problèmes de débit, d’usure et de corrosion. Les responsables ? La construction en acier ordinaire du réservoir, sa géométrie et la structure de débit en résultant au niveau de la carotte en sont les causes fondamentales. Une étude et une analyse des coûts indiquaient que la restructuration et la rénovation de la trémie permettraient d’augmenter la production et de réduire les coûts d’entretien et en capital. Un réservoir rénové permet de renforcer la sécurité ainsi que la fiabilité de l’exploitation, et sa durée d’activité prévue en est augmentée. En se fondant sur cet exemple, les auteurs de l’article décrivent la théorie du débit de matières solides en vrac et insistent sur l’importance de personnaliser la conception du système de manutention des matériaux en vrac à l’aide de propriétés rhéologiques adaptées afin d’améliorer la fiabilité, la sûreté et la rentabilité.INTRODUCTIONIn early 2013, Agrium’s Vanscoy Potash Operations (VPO) engaged Jenike & Johanson Ltd. (J&J) to provide testing, consulting, and structural engineering services related to proposed modifications to the 270 t special standard product surge bin, which Agrium planned to undertake during a two-week shutdown in August 2013. The bin, which had been plagued with flow, wear, and corrosion issues for its entire working life, was essential for the continuous operation of two of VPO’s compaction plants and for efficient dispatching to loadout. The bin often experienced product hang-ups, clumping on the walls, and plugging at the hopper outlet. Two recent unscheduled mill shutdowns had been partially attributed to flow issues in the bin due to clumping and product plugging up at the screws. These problems increased maintenance costs, limited production capacity, and degraded product quality. Holes and paper-thin sections in the bin walls discovered during a 2013 inspection revealed the potential for major hot material leaks or even structural failure. Either issue would stop plant operations until the bin could be repaired or bypassed. Clearly, the bin cone had reached the end of its life and required replacement."

Jan 1, 2018

By Yuki Koshino, Kenji Kaneko, Yasuhiro Aruga, Takuya Maeda

"In general, there is a strong correlation between dislocation characteristics and mechanical properties of aluminum alloys. In this study, dislocation characteristics of tensile deformed Al-Mg alloys were examined by transmission electron microscopy. An Increase in the solute concentration, ranging between 0.3 and 1.1%, Mg leads to increase in strength and decrease in uniform elongation. The accumulation of dislocations during the tensile deformation is observed in lower strain as the concentration of solute Mg in the alloy is higher. It is believed that the solute Mg in Al-Mg alloy promotes the accumulation of dislocation during the tensile deformation resulting in the decrease in elongation.INTRODUCTION The influences of the amount of Mg concentration on the tensile properties of Al-Mg alloys has been investigated by many researchers. It has been understood that the tensile ductility of Al-Mg alloy is higher for the Al-Mg alloys with higher Mg concentration beyond 2 mass% (Mukai, Higashi, Hirano & Tanimura, 1993). Uchida and Yoshida (1995) reported the formation of microbands during the tensile deformation due to the localization of dislocations, and the amount of microbands were reduced when the Mg concentration of the Al-Mg alloy was increased from 3 to 9 mass%. Their study suggested that the dynamic recovery of dislocation was retarded due to the increase of the Mg concentration during the tensile deformation, which resulted the increase in ductility. On the other hand, in the case of Al-Mg alloys with the Mg concentration less than 3 mass%, the reason why the ductility of Al-Mg alloys decreases with increasing Mg concentration has not been sufficiently investigated. In general, the Mg concentration used for automotive usage is less than 1 mass%, in the case of Al-Mg-Si alloys (Aoki, 2013). Therefore, to clarify the roles of Mg in the low concentration range on ductility of aluminum alloys and to elucidate its mechanism contribute to alloy design of Al-Mg-Si alloys having good formability."

Jan 1, 2018

By Junto Nishiwaki, Shinji Kumai

"Mechanical and physical properties of the impact welded dissimilar metal joints are controlled by joint interface morphology. An intermediate layer (IML) is often formed at the joint interface and this deteriorates the interface quality in some metal combinations. Numerical and experimental studies were performed in order to examine the formation mechanism of the wavy interface and intermediate layer for explosive welded Al/Cu dissimilar metal joints. The impact welding process consists of (1) high-speed oblique collision of metal plates, (2) metal jet emission and large deformation and temperature increase at collision point and (3) rapid cooling at the joint interface. Euler-Lagrange coupling method, smooth particle hydrodynamic (SPH) method and modified laplacianFoam (LF) method were linked together to simulate a series of processes from (1) to (3), and the final interface morphology including the formation of IML was reproduced. The wavy morphology (wave-height, wavelength) and the position and composition of IML formed at the joint interface of Al/Cu joints were quantitatively in good agreement with those reproduced by numerical analysis. Our simulation results are useful for the control of the interface morphology, reduction of the amount of IML, and improvement of the mechanical properties of the impact welded dissimilar metal joints.INTRODUCTIONImpact welding is a kind of solid state joining method providing extremely high joint strength for both similar-and dissimilar metal combinations. Explosive welding and magnetic pulse welding are representative methods to achieve the impact welding. By a high-speed oblique collision between two metal plates, a metal jet is emitted from the collision point. The metal jet can remove any oxide films and contaminations on the plates and produce an active refreshed surface. Consequently, good metallurgical bonding can be achieved even for dissimilar metals (Crossland, 1982). Solid metals deform like fluids under the high pressure condition at the collision point and characteristic wavy interface is formed. In addition to the wavy interface, an intermediate layer (IML) is often formed at the joint interface in some metal combinations. Elimination or reduction of the amount of IML at the joint interface is desired since the excessive IML formation along the joint interface causes a large reduction in physical and mechanical properties. Formation of IML is considered to result from characteristic thermal history at the joint interface including partial melting due to the local temperature increase and successive rapid cooling behavior at the joint interface. In order to control the IML formation at the joint interface, it is necessary to reveal both heating and cooling processes at the joint interface. However, it is impossible to observe the phenomenon occurring at the joint interface and also difficult to investigate the temperature change at the joint interface directly during the impact welding. Therefore, simulation or numerical analysis is indispensable to overcome this problem. In the present study, the explosive welded Al/Cu joint, which is prone to form IML at the joint interface, was selected for the research. By using a newly developed numerical analysis method, not only the formation process of wavy interface, but also the local temperature increase and successive temperature decrease at the joint interface were reproduced. The formation process of IML was investigated by using both numerical analytic and experimental results."

Jan 1, 2018

By J. B. Boisvert, D. S. Silva

"Drillhole placement involves benefits, costs, and constraints. Benefits are related to the drilling campaign value, which includes maximizing “indicated” and “measured” resources. Costs include drilling, rig movement, and access construction. Constraints include infeasible areas, maximum and minimum angles of drilling, maximum depth of drilling, and budget. Manually planning drillholes that meet these constraints is suboptimal. A framework for straight drillhole optimization that accounts for benefits, costs, and constraints is presented. The method aims to maximize the value of resources converted from “inferred” to indicated and measured. The framework is demonstrated for a Nevada gold deposit and outperforms manually selected drillholes.RÉSUMÉ Le choix de l’emplacement d’un trou de forage s’accompagne d’avantages, de coûts et de contraintes. Les avantages sont liés à la valeur d’une campagne de forage, qui comprend l’optimisation des ressources « indiquées » et « mesurées ». Les coûts englobent le forage, le déplacement de l’appareil de forage et la construction des routes d’accès. Quant aux contraintes, elles portent sur les zones impraticables, les angles maximums et minimums de forage, la profondeur maximale de forage ainsi que le budget. La planification manuelle des trous de forage répondant à ces contraintes est sous-optimale. Cet article présente un cadre relatif à l’optimisation des trous verticaux de forage tenant compte des avantages, des coûts et des contraintes. Cette méthode vise à optimiser la valeur des ressources converties de la phase « ressources présumées » à celle de « ressources indiquées et mesurées ». Ce cadre est appliqué à un gisement aurifère du Nevada et donne de meilleurs résultats que les trous de forage sélectionnés manuellement. INTRODUCTIONDetermining the optimum location of infill drilling has been studied because the high cost of drilling suggests that using fewer drillholes is preferred, and targeting locations of the deposit that are locally uncertain should result in better mine planning decisions and increased profit of the operation. Existing methods for optimizing drillhole locations consider minimizing the kriging variance (KV) as the objective and are mostly restricted to two dimensions (Soltani-Mohammadi & Hezarkhari, 2013a, b; Soltani- Mohammadi, Safa, & Mokhtari, 2016)."

Jan 1, 2018

By B. Skrotzki, E. Augenstein, C. Rockenhäuser

"The aluminium alloy 2618A is an Al-Cu-Mg alloy with additions of Fe and Ni, which is designed for long-term operation at elevated temperature in transportation and aerospace industries. The alloy degrades due to coarsening and dissolution of GPB zones and coarsening of S-Phase precipitates (Al2CuMg). This work investigates the overageing process at the application relevant temperatures of 190 °C for durations ranging up to 25,000 h. The nm-sized precipitates were selectively imaged along the <001>a direction of the Al matrix using dark-field transmission electron microscopy. The resulting images were then evaluated and allow the statistically relevant determination of radii distributions and the average radius of the precipitates dependent on temperature and heat treatment duration. Ostwald ripening of the S-phase does not describe the ageing process adequately. Instead, the evolution of GPB zones during the initial ageing regime needs to be considered in addition to the coarsening process of the S-phase. DSC measurements were performed to determine the presence of GPB zones in different ageing states. This will allow a quantitative description of the ageing process and a comparison to samples aged under external load.INTRODUCTION Alloy 2618A is an Al-Cu-Mg alloy, which is part of the 2XXX series of aluminium alloys. It is used in aerospace and transportation industry due to its desirable material properties for long term operation at elevated temperatures (Polmear, 2006). Fe and Ni are added to form intermetallic compounds, which retain microstructural stability at elevated temperatures (Bergsma, Li, & Kassner, 1996; Elgallad, Shen, Zhang, & Chen, 2014; Oguocha, Yannacopoulos, & Jin, 1996; Wang & Yi, 2006). The size and distribution of the nm-sized S-phase formed from the supersaturated solid solution (SSSS) during heat treatments mainly controls the strength (Khan, Starink, & Yan, 2008; Liu, Zhang, Ding, Sun, & Chen, 2003; Parel, Wang, & Starink, 2010; Shih, Ho, & Huang, 1996; Wang, Starink, & Gao, 2006). The S-phase has the composition Al2CuMg and is orthorhombic under equilibrium conditions (Heying, Hoffmann, & Pottgen, 2005; Perlitz & Westgren, 1943). Early experiments proposed the following decomposition of the S-phase sequence during heat treatments (Hardy & Heal, 1954; Silcock, 1961):"

Jan 1, 2018

By Tong Gao, Jingyu Qin, Xiangfa Liu, Zengqiang Li, Yaoxian Zhang

"The recycling of aluminum materials is a green industry while Al–Si–Fe is a typical scrap aluminum alloy. The key point of recycling Al–Si–Fe alloys is to separate Al and Fe. A method by introducing Al–Si–Fe alloy into Mg melt has been investigated in this work. A separation layer with gathered Fe–rich and Al–poor Fe3Al0.7Si0.3particleswereobtained at the bottom of the cooled ingot, indicating that ß–Al5FeSi phase evolves to Fe3Al0.7Si0.3,and quantities of Al are released to the upper Mg matrix simultaneously. However, the evolution of Al3Fe by adding binary Al–Fe alloy into Mg melt is different. It is supposed that element Si plays an important role in the phase evolution procedure, thus affects the performance of this method.INTRODUCTIONThe rapid development of aeronautic, automotive and aerospace technologies strongly depends on the consumption of materials while sustainable development is the future direction. Aluminum is a recyclable material and Fe is one of the most common impurities. Fe can be introduced into Al alloys by adding low–purity alloying materials and by using unprotected ferrous crucible, tools, or equipment (Belov, Eskin, & Avxentieva, 2005; Lu& Dahle, 2005).For instance, wear–resistant rings are usually inserted into piston head when producing Al–Si pistons and an infiltration procedure by putting the cast iron rings into Al melt before casting is always essential. As a result, both the re–melting of pistons and the reuse of Al melt for infiltrating rings lead to the enrichment of Fe element, which can be even high to5 wt.%(Viala, Peronnet, Barbeau, Bosselet, & Bouix, 2002).It is widely known that coarse ß–Al5FeSi particles will form in high Fe–contained Al–Si–Fe alloys which is harmful for the mechanical properties. In the past decades, several methods to eliminate the harmful effect of ß–Al5FeSi have been investigated which can be widely referred (Munson, 1967; Lee, Kawamura, Inoue, Cho, & Masumoto, 1997; Suárez–Peña& Asensio–Lozano, 2006; Eidhed, 2008).These methods can be divided into two kinds. One is to aggregate and remove the Fe–rich phase through the methods of centrifugation, gravity filtration or magnetic separation. The other way is modifing the morphology of flake–like ß–Al5FeSi by overheating the melt or adding neutralized elements. However, these traditional methods are rarely used due to respective disadvantages, while the commonly used method in industries is using primary aluminum for dilution. However, only less than 30wt.% of scrap Al can be added into primary Al melt for each melting work while it also results in the decrease of product quality simultaneously(Zhang, Liu, & Liu, 2016)."

Jan 1, 2018

By M. Somppi, Z. Yamak

"Gold producers invest significant effort in mining, processing, and creating an intermediate gold doré product. Nonetheless, equal effort should be extended to the final handling and processing of the doré bar, and managing the high-purity gold produced at the fine-gold toll refiner. This detailed attention to bullion handling and refining provides rigor and confidence that the mine site is achieving, through fair and controlled methodology, the most appropriate value for the final product. With the above in mind, the following study explores the importance of preparing a set of site best-practices for bullion handling and specifically, detailing the peculiarities of sampling methodologies and the impact on assays.INTRODUCTION Gold and silver handling practices are common place at mine sites and refineries. The practices include but are not limited to smelting, ingot casting, weighing practices, and secure transportation. Proper handling and processing of the bullion material ensures that the mine site is achieving the true value of the final product. Various handling aspects can critically impact the perceived value of the bullion. A few of these particulars include weight tracking, scale recertification and calibration, refining and melting practices, melt temperature measurement, sampling, pouring, bar cleaning, furnace technology and crucible selection, and assaying. Nevertheless, this report discusses and focuses on the importance of proper sampling and molten-metal temperature measurement and their potential impact on the final doré bar value. Refining or re-melting operations achieve a proper measure of the precious metal content of its bullion when the sample accurately represents the whole bar. At first this task appears seemly straightforward, however, taking a representative sample can be challenging and is also one of the most important tasks for valuing gold during the settlement stage at the precious metal refinery. Various bullion sampling methodologies exist; including: dip sampling, granulation, drilling, cutting, and vacuum pin sampling. The Royal Canadian Mint (2009) indicated in their technical review of refinery operations that pin sampling is one of the best methods for cases where representative sampling and accuracy are required, e.g. to determine the payable metal content. Pin sampling consists of inserting a sealed glass vacuum tube (Figure 1) into the molten metal; when the molten metal contacts a purposely-designed weak portion of the glass, the seal breaks and the metal is suctioned into the hollow centre (Figure 2)."

Jan 1, 2018

By S. Espley, T. Nyabeze, D. Beneteau

"Many mentorship programs are available to Canadian mining industry employees. Some are company-led initiatives, whereas others are provided through educational institutions or nonprofit organizations. In 2016, a national survey was launched to gain insight into perceptions of what mentorship is, learn about available programs, and collate experiences with formal and informal mentorship opportunities. This paper outlines survey findings and delivers recommendations to industry for consideration in employee mentorship programs. In addition, mining industry leaders share their mentor/mentee perspectives. The intent of this paper is to bring awareness of best practices that can help employees grow and develop in their profession.RÉSUMÉ Les employés de l’industrie minière canadienne ont accès à de nombreux programmes d’encadrement. Certains sont des initiatives menées par les sociétés, d’autres sont proposées par le biais d’établissements d’enseignement ou d’organismes à but non lucratif. En 2016, une enquête à l’échelle nationale a été lancée en vue d’obtenir des informations quant à la perception de ce qu’est réellement l’encadrement, de découvrir les programmes proposés et de comparer les expériences aux possibilités d’encadrement, officielles ou non. Cet article présente les résultats de cette enquête et fournit des recommandations à l’intention de l’industrie afin qu’elle les prenne en compte dans ses programmes d’encadrement des employés. En outre, des chefs de file de l’industrie minière partagent leurs points de vue conseillers/protégés. L’intention de cet article est de sensibiliser les employés aux meilleures pratiques, ce qui les aidera à évoluer et à se développer dans leur profession. INTRODUCTIONThis paper about mentorship in the mining industry is based on voluntary responses to a cold survey, written and circulated by the authors. In 2016, a link to an online mentorship survey was circulated to males and females in the mining industry with the belief that mentorship programs should be available to everyone. The link was delivered via the authors’ personal networks in mining, the CIM Reporter, Women in Mining (WIM) email blasts, LinkedIn, and Facebook. This paper summarizes the answers to the survey questions. The paper is a follow up to one by the same authors (Nyabeze, Espley, & Beneteau, 2010), which was written to gain insight into why women join and stay in the mining industry, and to learn why the overall representation of women is low."

Jan 1, 2018

By R. Holmestad, M. Gazizov, S. Wenner, R. Kaibyshev, J. K. Sunde

"Mechanical properties and microstructure of an Al-4.7Cu-0.74Mg-0.51Si-0.48Mn-0.10Cr-0.09Ti-0.02Fe (wt. %) alloy subjected to various thermomechanical processing (TMP) have been investigated and compared to conventional ageing at 170°C (designated T6). Three TMP routes involving cold deformation of solution treated samples were tested. These were (i) 3%-stretching (T8-3%), (ii) equal-channel angular pressing (ECAP) to true strain (e) of ~1 (T8-1) and (iii) ECAP to e~2 (T8-2), all with subsequent ageing at 170°C for 0-96 h. At peak age conditions, both yield stress, ultimate tensile strength and elongation-to-fracture decreased for the T8-3% state as compared to the T6 condition. Intermediate ECAP (T8-1 and T8-2) lead to significant increase in maximum yield stress, ultimate tensile strength and elongation-to-fracture. The changes in mechanical properties were related to microstructure evolution, encompassing changes in grain sizes, dislocation densities, precipitate morphology and phase fractions, which were characterised using transmission electron microscopy. Relations between TMP, precipitation behavior and contributions to different strengthening mechanisms are evaluated.INTRODUCTION Al-Cu-Mg-Si alloys are widely used as structural materials in aerospace industry due to their attractive combination of high specific strength, good fracture toughness and enhanced creep resistance. These properties are largely due to the formation of a large number of nano-sized metastable precipitates during artificial ageing (Polmear, 2006; Eskin, 2003; Gazizov, Dubina, Zhemchuzhnikova, & Kaibyshev, 2015). The precipitation behaviour in these alloys is complicated and depends among other things on Cu concentration and the Mg:Si ratio (Wolverton, 2001; Chakrabarti, & Laughlin, 2004). In general, the precipitation sequence has been presented in a prior study (Eskin, 2003) as follows:"

Jan 1, 2018

By E. Barnard, J. Tero, J. Rajala, N. Avenido, M. Fullam, A. Nashitati, S. Mbalamba

"The Otjikoto mining and milling complex is 90% owned by B2Gold Corporation, and began commercial operation on February 28, 2015. The milling circuit operates at a throughput 3.3 million tonnes per annum, with an average reserve gold grade of 1.28 g/t. The ore is high in Gravity Recoverable Gold (GRG), which varies between 73-91%, depending on ore type. Overall gold recovery since start-up is 98.2%, with about 63.5 % coming from the gravity circuit as doré. 2016 cash operating costs, and all in sustaining cost (“AISC”) were $361 and $604 per ounce, respectively.During design, three ore types were tested for GRG content, and based on the high GRG value of all three ore types, the decision was made to treat the full ball mill circulating load by gravity. Once operating, the gravity circuit performance was characterized by performing a detailed gravity audit, which included the ore, cyclone classification, Knelson concentrators, and the Consep Acacia intensive leach system. The deeper ores contain significant pyrrhotite, and this created some unusual challenges that had to be overcome. This paper presents the gravity circuit design process, the circuit commissioning, and the audit results and ongoing improvements.IntroductionHeadquartered in Vancouver, Canada, B2Gold Corp. was founded in 2007. Currently, B2Gold has five operating mines, and numerous exploration projects in various countries, including Nicaragua, the Philippines, Namibia, Mali and Burkina Faso. The Otjikoto Mine is located in the north-central part of the Republic of Namibia. It is situated approximately 300 kilometers north of Windhoek, the country’s capital, within the Province of Otjozondjupa. The Otjikoto mining and milling complex is 90% owned by B2Gold Corporation, and began commercial operation on February 28, 2015. The milling circuit operates at a throughput 3.3 million tonnes per annum. During design, a large emphasis was placed on gravity recovery, as the Otjikoto ores are unusually high in Gravity Recoverable Gold (GRG)."

Jan 1, 2018

"HPGRs operate in a wide array of applications in mining and minerals. These range from relatively coarse crushing of copper and gold ores at one end of the spectrum to the processing of fine iron ore pellet feed and fine industrial mineral products at the other. Traditionally these circuits involve the treatment of relatively moist materials in pre-grinding circuits; using single stage HPGRs in open circuit or as a closed circuit operation with screening or partial product recycle. More recently, HPGR is increasingly deployed in dry grinding in combination with air classification. The high throughput demonstrated by larger HPGRs has stretched the application towards coarser size reduction duties for a number of new projects. At the same time, the basic principle of inter-particle crushing for generating a product with a high fines proportion gives ground to investigate applying the technology further towards finished product duties. The advantages that HPGR brings are clear. Multi Stage grinding enables energy efficient size reduction across more of the comminution circuit. Primary HPGR serves for a coarse grinding duty, whereas a secondary HPGR is geared towards generating a fine product for downstream processing or even a finished product. This publication summarizes some of the features of staged HPGR circuits and discusses some examples of operating and projected applications.INTRODUCTION In most HPGR applications, the grinding units are used as a single process stage, either in open circuit, such as for pebble crushing [Rose 2002, Westermeyer 2000, Van der Meer 2015] or in closed circuit with classification [Van der Meer 2009, 2012] or product recycling [Van der Meer 2010]. Where a higher plant capacity is required, the HPGRs are commonly installed in multiple lines in a parallel arrangement [Parker 2005, Koski 201, Vanderbeek 2006]. HPGRs can take a wide range of feed size distributions, and grind this down to a product with a high fines content. In general view, there is a limit on the size reduction range that even an HPGR can provide. Grinding down from a very coarse ore (e.g. 70-100 mm) to a very fine product (e.g. 100 microns range) is stretching the ability of a single stage HPGR circuit. Fine grinding generally requires a classification stage that returns the classifier oversize to the head of the HPGR circuit. From one point of view, it can be demonstrated that when recycling a large proportion of fines and middlings back to the HPGR feed results in an effective feed with an overrepresentation of middlings and fines, which will eventually reduce the grinding efficiency and consequently result in an increased recirculation mass flow [Van der Meer 2014]. From another point of view the large recycling mass puts a strain or even a limit on the capacity of present-day conveyor capacity."

Jan 1, 2018

By Jean-Christophe Ehrström, Fanny Mas

"A specific test set-up has been developed to study at the lab-scale the high-temperature behavior of aluminium alloys in conditions close to those experienced by thick plates during hot-rolling. A particular attention is paid to reproducing both the stress triaxiality and strain fields that exist in plate during rolling. In addition to standard ductility measurements by means of secondary tensile tests (STT), multi-step plane strain compression (PSC) tests have been performed to mimic hot-rolling pass schedules. Tool and sample geometries were adapted to allow low h/a ratios (h= average specimen thickness, a= tool width) and thus guarantee depressive stress conditions at the center of the specimen during most of the test. Such conditions resulting in porosity opening can then be used to investigate the impact of rolling conditions on damage evolution. The mechanical testing was combined with post-mortem high-resolution ultrasonic scans allowing to detect small amounts of damage and quantify its evolution as a function of processing parameters such as strain and temperature. The test set-up was validated on two 2050-type AlCuLi alloys with different susceptibilities to high temperature embrittlement.INTRODUCTION Aluminium thick plates are widely used in the aerospace industry, mainly as semi-products to be machined for internal structure parts of wings (spars, ribs) and fuselage (frame). The conversion route of such products always involves a hot-rolling step, the conditions of which (temperature, speed, pass schedule) have to be optimized to maximize both mechanical properties and final plate quality. This goal cannot always be efficiently achieved by full-scale industrial trials as (a) cost limits the number of possible test conditions and (b) it is often difficult to change one parameter alone. That is why there is a need for laboratory-scale tests able to mimic the rolling process in terms of temperature, strain rate, stress triaxiality and deformation. Most laboratory hot-rolling mills do not adequately simulate industrial processing routes, especially in terms of heat loss, deformation speed and rolling geometry (maximum roll gap vs. work roll diameter). Concerning thick plate, it is of interest to achieve both similar deformation and L/h ratio (L=arc of contact, h=mean gauge) per pass as the industrial schedule because they are simultaneously involved in damage evolution and void closure during hot forming processes (Saby, 2014)."

Jan 1, 2018

By Eiichi Sato, Koichi Kitazono, Hiroshi Masuda, Kenta Higane

"The present study investigated the low-temperature creep mechanisms in ultrafine-grained (UFG) aluminum manufactured by accumulative roll bonding. UFG aluminum with grain size 0.39 µm showed steady state creep even at room temperature under low stresses as confirmed by the creep curves in the strain rate–strain plot. The low-temperature behavior was divided into four regions by three distinctive stresses, sI, sII and sIII: sI (=45 MPa) is denoted as the micro-yielding stress with which dislocations start movement, sII (=85 MPa) the dislocation-multiplication stress above which dislocations multiply with creep deformation, and sIII (=171 MPa) the conventional yield stress above which macroscopic plastic strain is generated. During low-temperature creep, below sI, negligible plastic strain is generated. Between sI and sII, creep deformation with stress exponent 2.5 occurred, which is accommodated by dislocation absorption into grain boundary and grain boundary sliding, similarly to the low-temperature creep of HCP metals. Between sII and sIII, creep deformation with stress exponent 7.0 occurred, whose mechanism is similar to the low-temperature creep of coarse-grained aluminum. Above sIII, power-law breakdown occurred.INTRODUCTIONIt is well understood that the creep deformation brings about at high homologous temperatures (T/Tm) of >0.4, where Tmis the melting point, with diffusion processes. Recently, the importance of aluminum is increasing for cryogenic temperature parts such as a metallic liner or a cap in high pressure-hydrogen vessels, and the presence of creep behavior in aluminum at room temperature has become recognized (Matsunaga, 2013;Kassner, 2015).In HCP metals and alloys, especially intitanium, steady-state creep behavior appears at room temperature with apparent activation energy of1/10 of that for self-diffusion(Neeraj, 2000; Matsunaga, 2009).On the other hand, Kassner (2015) claims that aluminum shows creep behavior at room temperature with apparent activation energy of 4/5of that forself-diffusion, but never reaches the steady state. We should note that it is derived from the data obtained from short-term creep tests of few hour, and Matsunaga (2013) already claimed the presence of steady state in room temperature creep in aluminum with activation energy of 1/5of that for self-diffusion.The mechanisms for low temperature creep are considered different between HCP and FCC metals: in HCP metals, grain boundary sliding is observed and is thought to accommodate piled-up dislocations at grain boundaries through absorbing them. The so-called slip-induced grain boundary sliding occurs with low number of activated slip systems(Matsunaga,2009).On the other hand, in FCC metals, many activated slip systems bring about work hardening with dislocation cell structure formation. In the initial stage of creep, it results in primary creep (Kassner, 2015), but Matsunaga (2013) claimed that once the annihilating of a cross-slipped dislocation to another reaches balance, steady state is established. It has been, however, strongly required to show more convincing experimental verification for the presence of steady state in FCC metals at low temperature."

Jan 1, 2018

By S. McPhail, D. Richardson, G. J. Simandl, C. Akam, S. Paradis, M. Yakimoski, A. Teucher, Y. Cui, F. Ferri

Historically, extracting dissolved solids from formation water was economically motivated. Today, main drivers are environmental benefits and regulations, as large volumes of water needed for hydraulic fracturing require treatment before reuse or disposal. The concentration of dissolved solids in flowback water increases with each use and may require treatment prior to disposal. Element recovery from produced water is not profitable unless market conditions are favourable, recoverable elements are abundant, and economical recovery methods are established. Sale of recovered materials could offset recycling and disposal costs. This paper describes markets for Cl, Na, Ca, K, Sr, Mg, Br, Ba, I, B, and Li, and their concentrations in produced water from oil and gas wells in British Columbia. It recommends revising sampling protocol for produced water.

Jan 1, 2018

By C. Pichler, C. Benigni, J. Antrekowitsch

"The recycling of steel mill dust results in zinc oxides which are sold to the primary industry in or-der to recover zinc in its metallic form. Due to the contained impurities - chlorine and fluorine - these sec-ondary oxides are usually charged into the roaster together with primary concentrates. Appearing problems in this furnace limit the application of secondary materials. Based on the zinc amount, a direct leaching, assumed that a low halide concentration is present, would be possible. To use the zinc solution directly in the electrowinning stage, the concentration of impurities, first of all iron, is limited. Iron can be found in secondary zinc oxides due to carry over during the recycling process. In order to reduce the iron content in the solution, the leaching has to be pH-controlled. This leads to a limited number of simple purification steps before the solution enters the electrolysis. Various trials were performed to evaluate the influence of temperature, time and sulphuric acid concentration on the iron dissolution. This paper deals with the results and also focuses on other impurities such as halides. Additionally, the soda washing process, usually done with secondary zinc oxides to remove most of the halides, and the challenges within this step are discussed.INTRODUCTION Recycling of steel mill dust, which is the main zinc containing residue, in the Waelz process dis-plays the common method worldwide. The product of the process is a secondary zinc oxide which is con-taminated with different elements like lead, iron and halides due to mechanical carry over or evaporation. Depending on the feeding material the concentration of each element in the dust is varying. The zinc con-tent of the product, also called Waelz oxide, lies around 65–68%. Based on these values it presents an al-ternative to the primary concentrate for the production of metallic zinc. The contained halides limit the direct utilization in the leaching stage and therefore have to be reduced. State of the art is a soda washing process but also solvent extraction gives a possibility to remove chlorine and fluorine but the desired con-centration for the electrolysis is hardly reachable (Antrekowitsch et al., 2016) Iron is present as an undesirable component of such secondary zinc oxides due to carry over. During the hot acidic leaching of the secondary concentrate, iron is dissolved too. Based on the higher electrical potential iron has to be removed before the zinc solution enters the electrowinning stage. It is usually removed by precipitation as goethite, hematite or jarosite, which is the common precipitation residue (Ismael et al., 2003)."

Jan 1, 2017

By A. Scheltema Beduin, H. Oterdoom, A. Haaks, C. Kempe, A. Liedtke

"For the Kazchrome DC Ferrochrome plant, SMS-group specifically designed an electrode column that would minimize downtime. Special features include the possibility for on load electrode jointing, on load slipping, and back-slipping. Electrode consumption is strongly related to furnace load and impedance, and is very low at high loads, which makes the graphite electrode an alternative to consider even in AC applications. The electrode could also be applied in other DC applications, as for example TiO2 slag, the novel Conroast process, or (twin) DC FeNi furnaces, and could possibly be installed during bigger shut downs. This paper will describe some of the design considerations and operational performance data on this novel column in the FeCr industry that could also be of interest for the FeNi or PGM industry if these would continue to develop towards DC technology.INTRODUCTION Every DC furnace has a cathode and an anode. The anode applied is commonly known as the Concast design, though the original design was by ABB who handed it over to Concast, subsidiary of the SMS-group. Some well-known DC furnaces outside the steel industry where the Concast bottom has been installed are listed in Table 1 as well as a few other key design features.Sidewall cooling and some other data have been left out for reasons of space, and being a lesser relevant design feature to this paper. HES stands for Hollow Electrode System, in which feed is charged through an electrode. Table 1 is built up chronologically according to first start-up date. Below comments are given to briefly explain some of the columns in Table 1: •,“Arm” in the “Cathode” column means that the design of the cathode holding and regulating mechanism consists of an electrode arm as depicted in Figure 1. •,Charging is relevant as some operations started with HES charging, whereas recently most new operations have started without HES but only charging chutes, of which at least some are close to the electrode and possibly others installed closer to the sidewall. •,“Dome” in the “Roof” column means that the design of the roof involves a center piece that can be exchanged if worn. •,The optimal roof design still seems to be a topic of debate, where no design is without problems."

Jan 1, 2017

By Xiaowen (Wendy) Ma, Hans Liang, Xiaoying Chen, David Way

"The mineralogical characteristics of the process streams provide key indicators to the potential improvement in the metallurgical performance. Therefore, the process mineralogy and diagnostic metallurgy have been widely used as a tool to assist the metallurgists at the operating plants. The challenge of this study was then how to characterize the diagnostic flowsheet of the minerals of interest in the process streams across the flotation circuit. The investigation from this study indicates that the minerals chematic flowsheet can visibly demonstrate the sources that caused the gold losses during the mineral processing.In this paper, we present studies of the flotation process stream samples, representing the feeds, intermediate products, final concentrate and final tails, which were produced from the flotation concentrators of Mt Carlton mine in Queensland, Australia. This study was focused on characterizing the process streams and learns how the gold in the process streams was associated with other sulphide minerals and host minerals on a size by size basis. The automatic QEMSCAN/MLA Particle Mineral Analysis (PMA) and Trace Mineral Search (TMS) were applied to identify the minerals and to detect the gold in the sized fractions of process streams. The Laser Ablation ICP-MS (LA) spot analysis, QEMSCAN EDS spot analysis and electron microprobe spot analysis were employed to identify and quantify there fractory gold concentrations in the sulphide minerals, like pyrite, and the elemental concentrations of visible gold grains. The diagnostic flowsheet of gold recoveries by the process streams, by mineral association classes and by the particle sizes were generated and discussed."

Jan 1, 2017

By Z. Ren, M. Tomlinson, E. Asselin

"Organic carbon blinding is a common, yet often partial, solution to the reduction of preg-robbing. A quantitative method to assess the extent of adsorption of a given blinding agent is presented herein. The adsorption of several blinding reagents on various carbon samples is quantified using electrochemical impedance spectroscopy (EIS). EIS results showed that kerosene is more strongly adsorbed on carbon than sodium lauryl sulphate (SLS), while SLS can hinder the charge transfer process of the oxygen reduction reaction on the carbon surface more effectively. The effectiveness of SLS is pronounced when its concentration is higher than 100 ppm. Raman spectra are presented for selected carbon samples: as the area ratio of the disordered peak to the graphitic peak increases, blinding agent adsorption increases.INTRODUCTION The presence of naturally occurring constituents in gold ores may adversely affect the extraction of gold in cyanide leaching since the gold cyanide complex, Au(CN)2–, can be adsorbed by these constituents (M. Adams & Fleming, 1989; Afenya, 1991; Miller, Wan, & Díaz, 2005). Such ores are known as “preg-robbing”. Preg-robbing behavior may arise from natural carbonaceous materials in the ore (M. Adams & Burger, 1998). In the past decades, a number of pre-treating methods have been developed for refractory carbonaceous ores (Arriagada & Osseo-Asare, 1984; Beer, 1994; Dunne et al., 2007; Jiang, Liu, Xiao, & Yang, 2012; Kohr, 1997; Kulpa & Brierley, 1993; Menne, 1992; Menne & Revy, 1994; Moyes & Houllis, 2010; Petrie, Craw, & Ryan, 2005; Simmons, 1996). The method known as blinding is one of the most effective and economical pre-treatment methods (M. D. Adams & Burger, 1998; Albert, 1923; Darrow, 1924; McQuiston & Shoemaker, 1975; Van den Berg, 2000). Blinding, also referred to as blanking or passivation, uses a chemical reagent to passivate the preg-robbing carbon by selective absorption or wetting (Bas, Altinkaya, Yazici, & Deveci, 2012; Brierley & Kulpa Jr, 1993; Dunne et al., 2012; Van den Berg, 2000; Yang, Qian, Song, & Dong, 2013; Yen, Amankwah, & Choi, 2008; Zhou, Jiang, & Choi, 2014). Organic reagents, which selectively adsorb on the surfaces of activated carbon and “smother” the surface, have been used for blinding carbonaceous matter in gold ores prior to cyanidation. Two comprehensive studies by Abotsi and Osseo-Asare and Adams and Burger have been published on this topic (Abotsi & Osseo-Asare, 1986; M. D. Adams & Burger, 1998)."

Jan 1, 2017

By C. Piribauer, E. Feichtenhofer, A. McEneaney

"As part of a major diversification project, RHI AG, through its plant in Drogheda Ireland, has developed a Caustic Calcined Magnesium Oxide (CCM) for use in the Cobalt (Co) & Nickel (Ni) hydrometallurgical extraction industry. In the course of the project, the company investigated the chemical and physical properties of a number of different Magnesia’s used in Co & Ni hydrometallurgy applications and has been able to determine the important parameters for a successful Magnesia for this application. A number of live plant trials have confirmed the results of this testwork and the company is now proceeding to produce this product in commercial quantities at Premier Periclase Ltd., the RHI AG plant in Drogheda, Ireland. This paper will outline the development work conducted by the company and highlight the important chemical and physical properties that make a successful CCM. Much of the research was conducted at the RHI Technology Centre in Leoben, Austria. In addition, a number of external laboratory studies were conducted on behalf of RHI AG. The result of this work has allowed the company to develop a Magnesia product with optimised properties for use in the Cobalt and Nickel hydrometallurgical extraction process.INTRODUCTION Premier Periclase is part of RHI AG, a globally operating supplier of refractory products, systems and services, headquartered in Vienna, Austria. The company produces Magnesia from seawater at its plant in Drogheda, Ireland. While the main focus is on production of refractory grade Dead Burned Magnesia for the steel industry, the plant also produces a number of different grades of Caustic Calcined Magnesia as well as Magnesium Hydroxide products. As part of a major project to diversify the company’s product base, the use of CCM in the Cobalt (Co) & Nickel (Ni) hydrometallurgical extraction industry was investigated. One of the company’s highly reactive grades of Caustic Calcined Magnesia was found to be particularly suitable for this application. In an effort to understand what makes a successful Magnesia for hydrometallurgy the chemical and physical properties of different Magnesia’s used in Co & Ni hydrometallurgy were investigated. This paper and conference presentation outlines the findings of this process."

Jan 1, 2017