Search Documents

By Norm Kirk, Robert Bittner

"The addition of a new powerhouse at the existing Tulloch Hydroelectric site on the Stanislaus River in the western foothills of the Sierras Nevada Mountains of central California required a deep excavation in rock on the downstream face of the dam. A cofferdam (water exclusion device) was necessary to isolate the powerhouse construction site excavation from the existing Goodwin Reservoir and the turbulent discharge from the existing powerhouse. The cofferdam was positioned on a steeply sloping fractured rock surface exceeding 50 degrees.This paper describes the challenges encountered during design and construction of the cofferdam and describes the unique design features used to address these challenges including:•,The use of flat-sheet-piles to form cellular walls on the steeply sloping rock surface.•,The use of 5-ft deep tremie concrete plugs in the bottom of the sheet pocket cells to create the bottom seal of the cellular cofferdam walls against the sloping rock surface.•,The use of vertical post-tensioned rock anchors to provide shear resistance at the contact point between the base of the cellular-wall and the sloping rocksurface.INTRODUCTIONModification or expansion of existing hydroelectric power plants often require downstream cofferdams or water exclusion devices to temporarily separate new construction from turbulent downstream discharge of the existing dam. Most dams are positioned on solid rock in the narrowest and therefore the steepest section of the river. This combination of steeply slopingrock and the need for an exclusion barrier creates a challenge for the design engineer trying to maintain a safe dewatered construction site. Typical cofferdam solutions for hydroelectric dams usually use large granular filled circular sheet pile cells that perform as gravity structures. However, this type of structures is not well suited to steeply-sloping highly irregular rock surfaces in a confined area."

Jan 1, 2017

By Andreas Brandner

"At the beginning of 2007 the Austrian contractor PORR was awarded with remediation works for a 48-km long part of the railway line from Campina to Predeal – part of the Trans European main Corridors TEN-T priority line 22 Bucurest – Brasov, connecting the southeast European countries with the heart of Europe.Due to partly new realignment and change of regular sections as well as protection against rockfall and slope slide a huge bunch of slope stabilization works became necessary, which were awarded to the contractor PORR and their designer IB-Brandner.Following the studies of the tender documents for the planned protection measures responsible managers of PORR decided to propose an alternative protection design by IB- Brandner. Changing the original design a more flexible and environmentally compatible solution consisting of high performance net, soil nailing and rockfall protection systems (fences) was elaborated and adapted to local needs. During design process, several critical areas were identified and additionally taken into account.In the paper examples of the design and erection process show how difficulties in implementation starting with the presentation of the idea continuing to the realization on site were managed and a technically more sophisticated and commercially competitive solution could be delivered to the customer Romanian Railway – case study.The European Commission awarded – following an election process in which all citizens of the EU could join - the remediation project Railway line Campina – Predeal in Romania as the environmentally best EU co-financed infrastructure project. GENERAL PROJECT EVALUATIONDue to original design slope stabilization should be done by concrete slabs fixed with prestressed anchors and shotcrete cover.The area to be secured was limited to a 12-meter strip left and right from the railway track without reference to nature and local needs. Discussions with the client and his designer and rising awareness for the hazards to address took several months. Site visits in Austria to provide insight in the problems of dealing with natural hazards helped to convince the client of the needs and our alternative design."

Jan 1, 2017

By Timothy C. Siegel, Paul J. Axtell

The Missouri Department of Transportation (MoDOT) recently replaced the Hurricane Deck Bridge that carries Highway 5 traffic across the Osage Arm of the Lake of the Ozarks in Camden County, Missouri. The former bridge was constructed in the 1920's and was supported on pneumatic caissons bearing on dolostone bedrock. The replacement structure is founded on drilled shafts socketed into the bedrock. During the design phase of this bid-build project, a baseline design was developed and Alternative Technical Concepts (ATC's) were allowed from approved contractors. Those ATC's were confidential and not shared between teams. Either the baseline design or the approved ATC design could be bid by the respective contractors. The baseline design included re-use of the 90-year old caisson foundations. Accordingly, an extensive evaluation of the caissons and underlying bedrock were conducted by coring, laboratory testing, acoustic tele-viewer (ATV), and cross-hole sonic logging (CSL) methods. The results of the investigation indicated the caissons were in excellent condition and suitable for re-use. However, a more cost-effective ATC was submitted, awarded, and constructed that did not re-use the existing caisson foundations but rather reduced the span lengths, increased the number of piers in the water, and supported those piers on drilled shafts. Interestingly, the difference in low bid price between the awarded ATC and the baseline design was less than one percent of the construction cost. This paper describes the multiple foundation designs that were necessary for this interesting project. The various foundation evaluations include the existing pneumatic caissons, large-diameter open-ended pipe piles to support the baseline design, and the design of rock-socketed drilled shafts that were successfully constructed in 2012.

Jan 1, 2017

By Rob Jameson

"The demand for commercial and residential construction has continued to evolve across the United States over the last decade. Our markets demand larger, deeper and inherently more complex structures, located within increasingly constrained urban locations and with challenging geotechnical conditions. As project demands incrementally escalate, specialty contractors are continuously challenged to extend their state of practice. Development in the size and capabilities of construction equipment, tooling, techniques, monitoring and verification systems over the last decade has consistently allowed contractors to build larger and deeper. For support of excavation (SOE), in addition to scale, selection of the most appropriate system has been a key to success in the most challenging ground conditions. This selection process is based on sound engineering and construction practice, and also prior experience, both positive and negative. Ultimately many Owners have chosen to manage their risk of SOE construction through design-build contracts, which allows specialty constructors to optimize the balance of cost, schedule, scope and associated risk based on their local expertise. Successful implementation of a design-build methodology begins long before a contractor is selected, with identification of key project requirements and risk factors during the feasibility studies and design development phases. In these early stages of the project development, advice and budgets are frequently solicited from Specialty Contractors. The Owner, Construction Manager and Consulting Team will filter this input from multiple sources to provide their specific recommendations, develop construction documents and select the appropriate form of contracting. Only in the final stages, after award of a Design-Build Subcontract, can the successful specialty contractor directly influence risk management approach on the project. A case study is presented from Block 9 in San Francisco’s Transbay District. This project demonstrates the incremental identification, assignment and mitigation of construction risk through the planning and design build process for SOE on the deepest planned excavation in San Francisco.INTRODUCTIONThe mature urban development market in United States results in high demand for complex Support of Excavation (SOE) schemes on constrained sites. The Design-Build approach can be applied to increasingly difficult SOE challenges, combining regional specialty subcontractor knowledge and experience in order to optimize solutions for cost and schedule. The most successful applications will involve early engagement of shoring subcontractors within the project teams, during feasibility and design development stages, in order to identify key scope and risk issues, and their potential solutions. Throughout the project development, it is important to reasonably assign responsibility for construction risks amongst the project stakeholders who are best able to control them.This paper presents a case history for San Francisco’s Block 9, a well-planned and successfully executed design-build SOE project in San Francisco’s Transbay Redevelopment area. Throughout the 4 year period from the Developers initial proposal to the Redevelopment agency, through completion of excavation down to subgrade, the project team developed a series of increasingly refined SOE schemes, with corresponding scope definition and cost and schedule estimates. This program relied on early identification of key challenges and risks for the project, and evolved through multiple phases of proposals as first the General Contractor (GC) and then Specialty Shoring Subcontractor were engaged for the project. The scheme, cost and schedule refinements continued throughout construction in order to accommodate unanticipated conditions and events as they unfolded."

Jan 1, 2017

By Michael A. McNicholas

"Deep foundations utilize the varying soil conditions to provide the most cost-effective or practical scope for a given jobsite. Once the scope has been determined and the engineering applied, the element can be installed and tested to determine if it is suitable. QA/QC programs are vital for the assurance that the element designed by the engineer has not only been properly constructed but that the design assumptions are confirmed. The two deep foundation elements referenced are drilled displacement piles (DDP) and micropiles. Each of these elements allows for large loads to be distributed deep into the subsurface geology. Having the technology and ability to monitor the tests in real-time can be beneficial to a contractor in determining if the design is adequate or if adjustments need to be made on future piles. The proper QA/QC guidelines for installation and monitoring need to be in place to ensure that an accurate interpretation can be made on the pile. This paper discusses the typical testing and the positive results that the author has encountered using the latest advances in strain analysis.KEY TERMSDrilled Displacement Piles:A deep foundation system that has the ability to shed load into the geology through shaft resistance as well as tip resistance, similar to drilled shafts. This pile element is unique in that it has a consistent pile section and thus a consistent modulus of elasticity.Micropile:A deep foundation system used in applications where the foundation lies over material not suitable for a spread footing and the ideal soil stratum is deep below the foundation. Micropiles will have two different cross-sections consisting of a cased section and an uncased section. For this reason, this pile type requires additional analysis when computing stress-strain relationships.Geokon Strain Gauges:Instrumentation such as Models 4911A-4911 Vibrating Wire Strain Gauges ( known as Sister Bars) are designed to be embedded in grout and calculate loads based on the change on grout strain over a period of time.Stress:A pile element is under a compression (axial loading) load when a force acts along its axis and is normal to the plane of the section. The corresponding stress the pile is experiencing is described as a normal stress. The stress is obtained by dividing the magnitude of the load distributed over the cross-section by the area of the pile cross-section, as shown in Eq. 1."

Jan 1, 2017

By Paul J. Sabatini, Yazen A. Khasawneh

"A Demag CC1800 crawler crane was partially erected on crane mats adjacent to a seawall when settlements near a corner of the crane mat area were observed to be slightly larger than previously assessed. A ground improvement program including installation of dry soil cement mix (DSM) piers was implemented to improve soil bearing capacity. Due to near-surface obstructions, only 75 percent of the DSM piers were installed to the design depth. Because of the partial installation of the DSM piers, an evaluation of the crane pad stability and the effect of the crane loading on the stability of an adjacent 10-ft high concrete seawall, which was believed to have limited (if any) reserve capacity, was required. A two-dimensional finite element model was developed to evaluate the responses of the partially improved ground and the sea wall to the loads imposed by the crane. Geotechnical site investigation and laboratory testing programs were performed to better define the subsurface conditions near the area where settlements occurred and to provide the required mechanical parameters for the soil constitutive model. Analysis results indicate that total and differential settlements of the crane pad and the increase in load on the seawall were tolerable provided limited excavation and replacement of weak dredged soils outside the DSM area would be implemented.INTRODUCTION & BACKGROUNDA Demag CC1800 was erected on 8 ft × 16 ft crane lattice mats at about 12 ft from an existing seawall. Approximately 3.5 in. of subsidence was observed at one corner of the crane mats, while the crane was partially erected and stationary. The approximate location of the crane mats with respect to the existing seawall when the subsidence occurred is shown on Fig. 1.The seawall consists of a reinforced concrete wall connected by reinforced concrete bents to a composite section of sheet pile wall; the total depth of the seawall is about 29 ft. The bents are spaced at about 20’4” and supported by five piles at each bent location. The composite sheet pile consists of concrete and a sheet pile section with a reinforced concrete wale section. The retaining wall is about 10 ft in height and is supported at three levels. The first support level comprises a 2-½” diameter steel rod near the top of the wall spaced at 40’8” the second and third level supports comprise 1-½” diameter steel rods spaced at about 5’6”. The second level support is inclined at about 10 degrees below horizontal and the third level support is oriented horizontally through the wall footing. A schematic of the seawall section is shown on Fig. 2.A geotechnical site investigation was implemented soon after the subsidence was observed. The program included advancing four borings to a depth ranging from 16 ft below ground surface (bgs) to about 30 ft bgs. In general, the investigation showed sandy material (likely fill that was used behind the retaining wall) from the ground surface in two borings located immediately behind the retaining wall. The other two borings furthest from the retaining wall showed very soft to soft clay (possibly dredged material) from the ground surface to a depth of about 10 ft bgs. Based on this information, the ultimate bearing capacity of the subsoils was estimated to range from 1,200 to 2,000 pounds per square feet (psf). From the anticipated crane loading (weight of the crane and loading lifts), a minimum allowable bearing capacity of about 1,500 psf would be required for safe operation. To achieve the required bearing capacity a ground improvement program was selected and implemented."

Jan 1, 2017

By Clinton O. Rex, Adam S. Hurley, W. Morgan NeSmith

"Hartsfield-Jackson Atlanta International Airport underwent a $1.2 billion dollar expansion project centered on the construction of the new Maynard H. Jackson International Terminal. Passenger access between the new International Terminal and the domestic airport facilities is primarily via underground Automated People Mover (APM) trains. Prior to this expansion, the APM tunnel terminated beneath Concourse E, which previously served all international flights. The new International Terminal is located approximately ½-mile from the previous terminus of the APM tunnel.A paper describing the general approach to excavation support for construction of the entire APM tunnel extension from under Concourse E to the new International Terminal was published by two of the authors (Hurley and NeSmith, 2014). One of the features of note of the approach involved the intersection of the proposed new alignment of the APM tunnel extension under Concourse E with the old terminus. Specifically, the new tunnel extension conflicted with the location of the existing Auger Pressure Grouted (APG) piles supporting four columns in Concourse E. This paper presents design and installation details of the micropile underpinning approach used to support the existing columns to allow for the proposed excavation including the cutting and removal of the existing APG piles, while allowing Concourse E to remain in service during construction.PROJECT DETAILSGeneralThe construction of the APM extension required an excavation support system for a 450-ft long, 55-ft deep excavation across Taxiway Dixie and a 900-ft long, 30-ft deep excavation beneath the basement of existing Concourse E. The excavation under Concourse E required both excavation support and support of the existing columns over the proposed excavation zone. A general overview of the work area is shown on Figure 1."

Jan 1, 2017

By Tae Hwan Lee, Jun-Shin Lee, Daejin Kwag, Sangchul Bang, Gerard T. Houlahan, Moo Sung Ryu

"Geotechnical engineers have been installing innovative, permanent underwater foundation systems utilizing suction buckets for the offshore industry since the early 1980s (Senpere and Auvergne, 1982). This foundation system has been successfully used on numerous and various types of offshore structures in a wide range of environments. Suction buckets have numerous advantages compared to conventional underwater foundation systems. The more notable advantages include easy installation, large loading capacity, low noise and retrievability. The application of reduced water pressure inside the bucket facilitates the installation of the suction buckets, where a suction pump attached at the top of the bucket can accomplish the entire driving operation. Because of this efficient operation, very large suction buckets can be driven into the seafloor, which eliminates the use of a large number of small piles.In Korea, one of the most economical and reliable renewable energy sources is wind power; however, onshore wind power generation has encountered many problems, such as the lack of favorable sites and public concerns about noise and environmental damage. Consequently, offshore wind power generation has attracted increasing attention due to its abundant potential, high efficiency of grid connection, and availability of easy expansion.In November 2011, the government of Korea announced a national offshore wind power development roadmap, which targeted its offshore wind power generation with the goal of becoming one of the top three nations in the world for offshore wind power generation. Korea Electric Power Corporation Research Institute (KEPRI) is the main research arm of the Korea Electric Power Corporation (KEPCO) and conducts research and development on electricity, power generation, renewable energy and other energy-related matters. KEPRI ultimately provides forefront knowledge and leadership to KEPCO with respect to energy and related areas for its near- and long-term needs. Financial support for the overall project, of which the suction bucket foundation system installed for the pilot phase wind turbine is described below, was provided from the New and Renewable Energy Program of the Korea Institute of Energy Technology Evaluation and Planning funded by the Korean Government Ministry of Trade, Industry and Energy."

Jan 1, 2017

By Paul Suver

"The closed loop standing column well (CLSCW) system uses a closed circuit of water to develop the same thermal heat exchange characteristics that are achieved from traditional open circuit standing column well that uses the ground water directly. Pipe pile and pipe anchor foundations can be used as CLSCW components for ground source heat exchange. New data gathering and analysis techniques and equipment installed in the heat pumps allow any mechanical engineer to design the system without specialty engineering equipment and certifications.CLSCW Description:Closed end steel pipe of varying outer diameter (O.D.) is installed by various technologies at varying depths depending on subsurface geology. The wells are arranged as stand alone wells or in groups joined in parallel or in series or in a combination of both. These pipes may also serve a dual function as foundation supports, deep foundation pile, anchors or earth retention components. These wells are then internally coated to minimize corrosion. The wells are then plumbed and capped to create a vessel equipped with a supply and return water line.The stand alone well or group of wells is then used as a ground heat exchanger for a ground source heat pumps located in or around the building.The ground source heat pumps provide heating and cooling to the building either with a traditional ducted distribution system or with radiant heating and cooling. These systems can reach efficiencies three times greater than traditional gas fired heat sources and five times greater than traditional air conditioning sources."

Jan 1, 2017

By Matthias Pulsfort, Markus Herten, Rolf Breitenbücher, Claudia Fierenkothen

"Secant bored pile walls are frequently used as retaining walls in watertight excavations to cut off ground water aquifers and are subsequently exposed to ground water pressure loading in addition to earth pressure loads. To avoid extra loading from ground water pressure in soils with limited permeability, it can be useful to arrange drainage windows within secant bored pile walls by means of single primary piles filled with porous concrete without reinforcement cages, which usually have to be placed within casings in submerged conditions. This concrete may serve as a horizontal arch between the reinforced secondary piles, but it must however enable vertical draining between load carrying construction beams and the bottom of the excavated pit. In the present submission, the results of several material tests with different mix designs of porous concrete with certain admixtures are presented together with first and important experiences with a wellsuited placement technique for porous concrete casings in small- and large-scale laboratory tests. It can be shown that the usual placement technique of employing a tremie pipe is not suited for this type of unsaturated concrete. Instead, pouring with a particular kind of cone and an open conductor pipe has proven successful.Additionally, special testing methods are currently developed for judging the suitability of the desired concrete mix design in preparation for an upcoming real-scale experimental pile installation in Germany.1. INTRODUCTIONRetaining walls are often built as secant bored pile walls in order to cut off aquifers saturated with groundwater against deep building pits. In soil types with relatively low permeability, however, seepage flow may be permitted, because the quantity of groundwater to be pumped is limited, and the range of influence due to dewatering is not reaching far. Thus, the hydrostatic water pressure on the retaining wall can be considerably reduced, leading to a more economic design (see Fig. 1).In unsaturated soils, the dewatering effect can be achieved by means of porous pervious concrete with a uniform grainsize distribution of aggregates typically placed in a borehole under dry conditions. With regard to the use of porous concrete to be placed at the ground surface in road pavement applications, experience is sufficiently available as shown, for instance, by Neithalath et el. (2010). However placing the porous concrete in a bored pile using a tremie pipe under submerged conditions is a challenge and a completely new approach, because there is a considerable risk of segregation of the fresh concrete, separating the cement lime paste from the aggregates when in contact with water and leaving only neat gravel on the one hand as well as a tight cemented area at the bottom of the pile on the other hand. If this concrete placement is successful, additional dewatering by means of extra wells behind the retaining wall can be avoided. Of course the seepage flow in the adjacent soil needs to be regarded seriously."

Jan 1, 2017

By Kyle Murphy, John S. McCartney

This paper focuses on the seasonal thermo-mechanical response of two energy foundations installed at the new Denver Housing Authority Senior Living Facility in Denver, Colorado. The two drilled shaft foundations, which have diameters of 36 inches and depths of 45 ft and are end bearing in the Denver shale formation, include a closedloop series of polyethylene tubes through which fluid is circulated to exchange heat with the surrounding ground. The tubes within the foundations are coupled together with the conventional ground source heat pump system for the building and were installed to evaluate the heat exchange response of the foundations as well as any thermomechanical soil-structure interaction effects. A series of vibrating wire strain gages and thermistors were installed at different depths in the foundation to record the thermomechanical strain and temperature at different depths. Also, pipe-plug thermocouples are used to measure the inlet and outlet temperature of the heat exchanger fluid entering each of the foundations, which is necessary to evaluate the total heat exchange for the foundations and the efficiency of the heat pump. This paper will describe the energy foundation construction processes, the strain distribution and ambient temperature profiles during building construction and the seasonal strain and temperature distributions during heating and cooling of the building. The data indicates that typical heat exchange associated with heating and cooling operations leads to strains which are within acceptable limits, and that the foundations can provide a clear option for absorbing the base heating and cooling load for the building.

Jan 1, 2017

By Douglas G. Baker, Jason K. Braund-Read, Megan R. Sheffer

"Mica Dam, owned by British Columbia Hydro, is an 820 ft high earthfill embankment dam that was completed in 1973. The dam consists of a thin central impervious till core supported by upstream and downstream compacted sand, gravel and cobble shell zones, founded on bedrock and valley bottom alluvium deposits. In 2012, a project was started to install new piezometric instrumentation within the dam’s foundation and downstream shell zone.Deep drilling in large embankment dams is very difficult and requires careful planning to select a methodology capable of reaching the target locations, while ensuring that no damage is done to the surrounding dam fill zones. At Mica Dam, the drilling could only be carried out from the Dam Crest and drillholes had to be carefully oriented to avoid intersecting any existing dam instrumentation. The drilling work therefore required angled drillholes, at depths of up to 855 ft, through heavily compacted sands, gravels and cobbles, and to significant depths below the standing water table.During the planning stages for the Project, in early 2013, the preferred drilling method was selected and a drilling contractor was engaged for the drilling work. Critical dam safety concerns were identified and addressed during the design stage of the Project with the drilling contractor, so that risk mitigation measures and response plans could be effectively developed.This paper explains how background information and prior drilling experience influenced the final design and implementation of the drilling techniques used in 2013 to successfully drill the deep holes and carry out the piezometer installations in Mica Dam. Drilling procedures, instrumentation design and installation methods, as well as risk mitigation measures, are discussed."

Jan 1, 2017

By John Erikson, Alan J. Lutenegger, Nicholas Williams

"In order to evaluate the level of disturbance produced in clays during installation, a series of single-helix and multi-helix anchors were installed at a test site consisting of a stiff overconsolidated clay crust overlying softer near normally consolidated clay. Field vane tests were then conducted over the top of the helical plates at various depths to determine the undrained shear strength after installation and were compared with undrained shear strength measured in adjacent undisturbed ground. The tests represent the first time that the degree of installation disturbance has been evaluated directly and show that even with perfect installation practice the clay is disturbed as a result of rotation of the helices during installation. The results show that the soil is not completely remolded but that the strength is below the peak undrained strength of the adjacent undisturbed ground. Measurement of the installation torque and the rate of advance are used to define an “Installation Disturbance Factor” which may help to evaluate the quality of the installation by the Contractor and degree of soil disturbance. INTRODUCTIONAn important consideration in the design of Helical Anchors is the degree of disturbance to the soil during installation. This may be especially important for saturated fine-grained soils where the disturbance from installation may produce a reduction of the undrained shear strength. Even though this was recognized as early as 1950 by Skempton, soil disturbance is often ignored by engineers using current design procedures. Field investigations were performed to obtain both directs and indirect evaluation of the degree of disturbance produced by the installation of single-helix and multi-helix anchors in clay and the influence of disturbance on behavior. The investigations involved measurement of torque and advance during installation, load tests performed to determine load-displacement behavior and ultimate capacity and field vane tests performed over the helical anchors to evaluate changes in undrained shear strength as compared to adjacent undisturbed ground. The characteristics of the site and details of the installation are presented. Results of the field vane tests are shown for a number of helical anchor installations and results of load tests are presented. The results indicate that a reduction should be made to the undisturbed undrained shear strength for design and that the reduction may be related to the Sensitivity of the clay and quality of installation."

Jan 1, 2017

By Rouzbeh Afsharhasani, Moses Karakouzian, Brandon Kluzniak

"The Vegas High Roller is the centerpiece of a new development parcel adjacent to the Las Vegas Strip. At a height of 550 feet, the High Roller is currently the tallest observation wheel in the world. The design team conducted a geotechnical site investigation to characterize the alluvial soils and cemented layers encountered and to provide foundation design recommendations for the observation wheel, boarding platform, and temporary structures needed to erect the wheel structure. This paper presents a case history of the geotechnical design process, including development of a ground model and design parameters, high-strain dynamic axial load tests, and settlement monitoring during construction. Results indicated that design parameters were conservatively assumed and that the majority of the axial load was transferred to a near surface caliche layer, thereby resulting in insignificant settlement of the foundation system.IntroductionThe engineering of the Vegas High Roller is similar in concept to that of the London Eye and the Singapore Flyer. The wheel has 28 cabins, each with a capacity of 40 persons. The top point of the structure is 550 ft above ground level at the site.A geotechnical site investigation program was undertaken and subsequent analyses were performed to provide foundation recommendations for the observation wheel legs, boarding platform columns, and temporary structures directly associated with construction of the observation wheel."

Jan 1, 2017

By Rafael A. Rivera

"Since the dawn of construction, there has been a need for excavations, which sometimes need to occur below the groundwater table. Excavations in themselves are difficult enough, with the myriad of requirements, such as engineered support of excavations, considerations for stability and numerous other concerns. Excavations executed in rural landscapes can be accomplished easily without significant consideration to accessibility, adjacent properties or structures, and construction limits and deformations. However, all of these factors can have an impact on excavation considerations in an urban landscape. When digging below the groundwater table, these conditions, along with concerns associated with groundwater drawdown requirements, discharge limitations, groundwater contamination, property limits, adjacent buildings and subsidence concerns, can lead an experienced dewatering contractor to consider diverse installation methodology and equipment to allow construction to occur below the groundwater table.534 W. 29th St. New York, N.Y.There are many things that must be considered when constructing a new high-rise building within a small property footprint measuring 25 ft (7.6 m) wide by 80 ft (24.4 m) in length. When you take into account that the foundation needs to go several feet below the groundwater table and that there are two existing multistory buildings with shallower foundations on either side of the proposed structure, this task now becomes much more difficult. Consideration of geology, groundwater levels, depths of excavation and shoring for the excavation becomes critical to the success of the project. On a regular basis, dewatering contractors confront similar situations in congested cities where available real estate is limited.To minimize the negative impacts of construction dewatering, it is important to mitigate the potential effects of construction dewatering to the surrounding buildings, sidewalks, underground structures, tunnels, subways and other existing infrastructure. Such an instance occurred at the project located at 534 W. 29 St. in New York City. On this particular project, the required drawdown was greater than the typical 15 ft (4.6 m) of suction lift, so a vacuumed can pump system was utilized. The tubing was connected to a vacuumed perimeter dewatering well-point system, which is a predrainage system that is installed prior to the start of excavation for the underpinning of the adjacent structures and for the overall foundation. Each well-point, which was composed of a PVC pipe that was 1.5 in (38 mm) in diameter by 25 ft (7.6 m) long, was drilled to a depth of about 23 ft (7 m) using a hollow stem auger and was installed around the perimeter at a centerto- center spacing of about 7.67 ft (2.3 m). In lieu of a traditional perimeter collection header, and to allow for greater flexibility for the contractor, the well-points were interconnected to a modified vacuum can pump system utilizing ¾ in (19 mm) drop tubes that were “spaghetti” around the perimeter."

Jan 1, 2017

By James M. Tantalla, Roderic A. Ellman, W. Allen Marr, Scott R. Bamford

"Construction of the powerhouse for the Willow Island Hydroelectric Project required a 100-ft deep excavation inside the limits of a cofferdam and embankment-seepage cut-off wall through soil and rock adjacent to the Ohio River. Portions of the rock had preexisting weak plans and slickensided surfaces with low frictional strength. Stability analyses were performed for critical sections of the excavation to evaluate the stability of the soil slopes and rock cuts using buckling, tension crack, and limit equilibrium analysis techniques. Loading conditions included the 100-yr and intermediate floods, normal pool, sudden drawdown, and seismic design conditions.Stability analyses indicated adequate factors of safety for soil slopes and for rock cuts through the landside embankment sections. However, the results of deep-seated stability analyses through the rock supporting the riverside cellular cofferdam indicated unacceptable factors of safety. Consequently, the riverside portion of the excavation required measures to increase stability. Long, high-capacity rock anchors and deep dewatering wells to lower the site piezometric head were chosen for this purpose.Thirty high-capacity rock anchors were installed on the upstream, riverside, and downstream sides of the cofferdam rock cut. Required rock anchor loads varied from 1,968 to 2,074 kips. The designed anchors consisted of multiple, seven–wire strands with up to 59 strands per anchor. Bond lengths used an allowable bond stress of 100 psi based on the rock bond measured with pull-out tests. Maximum bond and anchor lengths were 50 ft and 140 ft, respectively. Measurements of forces in selected strands and displacements of the excavation showed excellent performance."

Jan 1, 2017

By Arash Khosravifar, Amalia Giannakou

"Nonlinear foundation springs for bridge caisson foundations show significant coupling between the shear force and bending moment. Implementing foundation stiffness matrix with coupling effects (off-diagonal components) into the global bridge model presents numerical challenges. A simplified approach is developed to model foundation springs including coupling effects using a simple methodology. This simplified model include one translational spring and one rotational spring combined with a rigid link in 2D space. Results show that nonlinear springs (translational, rotational and coupling) can be reasonably captured using this simplified procedure.INTRODUCTIONThe Izmit Bay Bridge is a 3-km long suspension bridge that crosses Izmit Bay in Turkey and is being constructed in a highly seismic region. Figure 1 shows the project location. The South Approach Viaduct (SAV), located along the western margin of Hersek peninsula, is within 5 km from the North Anatolian Fault and within a zone of secondary deformation around the primary trace of the North Anatolian Fault. The proposed SAV consists of 11 Piers and an abutment at the south end of the structure."

Jan 1, 2017

By K. Madhusudan Reddy

"Pile response under combined uplift and lateral load is very important and it is imperative to evaluate the effect of combined loading and only few studies were reported on pile behavior under combined uplift and lateral loads. Model pile made-up of aluminum having an outer and inner diameter of 25.4 mm and 19.4 mm respectively is used. Dimensions of the model steel tank are fixed as 1.0 m x1.0 m x 1.2 m (depth) to avoid the boundary effects under combined lateral and uplift loads. Experiments were carried out on single piles at isolated uplift, isolated lateral loading and combined lateral and uplift loading, embedded in sandy soil. Results indicate that load–deflection behavior is nonlinear for isolated uplift and lateral load tests as well as in case of combined loadings. It is also observed that the behavior of piles under isolated loadings is substantially different when compared to combined loading.INTRODUCTIONPile foundations are generally used to support compressive loads from superstructures. Some structures, like transmission towers, mooring systems for ocean surface or submerged platforms, tall chimneys, jetty structures, etc. are constructed on pile foundations, which have to resist large lateral and uplift loads and moments. The various loads (compressive, lateral and uplift) and moments act on the piles simultaneously rather than isolated manner. There are well-established theoretical methods present to evaluate the pile behaviour under different isolated loadings namely, verticalcompressive, vertical-uplift and lateral (Poulos and Davis, 1980), but there are very limited studies focused on pile behaviour under combined loadings. Though there is good number of studies reported on pile behaviour under combined compressive-lateral and compressive-uplift loadings (Ramasamy, 1974; Jain et al. 1987; Zhang and Small, 1999; Dash and Pise, 2003; Karthigeyan et al. 2006 & 2007; , there are only very few studies reported on pile behaviour under combined uplift and lateral loads. Darr et al. (1990) described an approach to a rational solution of the interaction of pile to combined uplift and lateral loads based on analytical and experimental studies. Influence of cyclic loading was also considered. Narasimha Rao and Prasad (1993) investigated the uplift behaviour of pile anchors subjected to lateral cyclic loading. There were many onshore and offshore situations where lateral cyclic loading may affect both the pullout and lateral loading capacity of pile anchors. Jetty and wharf structures are usually subjected to lateral forces from wave and wind action. If these cyclic lateral loads are acting on the supporting piles, the resulting movement of the upper part of the embedded length of pile may reduce the skin friction. This progressive deterioration in pullout resistance may not be reflected by a pullout test made soon after the installation. Hence, Tomlinson and Woodward (2008) pointed out that a generous safety factor on the ultimate pullout load should be adopted for piles in such situations. Mroueh and Shahrour (2007, 2008) presented a threedimensional finite element analysis of the response of battered piles to the combined lateral and vertical pullout loads. Nevertheless, the model is not validated well due to lack of good experimental data based on rigorous experiments. Thus there is a scope for investigating the effect of lateral load on pile behaviour under uplift load and vice versa based on carefully designed experiments, which is main focus of the present investigation."

Jan 1, 2017

By Claudio Asioli

"The project’s goal was to construct the Al Ghazala Intercontinental, a multi-use development in the bay area of Tripoli overlooking the Mediterranean Sea. The site of the project is located approximately 500 ft (150 m) from the Mediterranean coast, near the Al Ghazala roundabout in the town center of Tripoli, Libya. The investor of the project was Magna Properties Group, Ltd. – Libya, the main contractor was Man Enterprise S.A.L., and the design and construction management was performed by Dar Al-Handasah Engineering. Trevi S.p.A. was contracted to perform the design and construction of the anchored diaphragm walls and dewatering systems for the excavation of a two-level basement car park, which extends across the full footprint of the site.The site was approximately 640 ft by 230 ft (195 m by 70 m) in plan and nearly flat. The groundwater level typically varies from about 11 ft to 23 ft (3.4 m to 7.0 m) above mean sea level. To construct the required raft foundation, it was necessary to excavate the area down to El. -15.7 ft to -26.3 ft (-4.8 m to -8.0 m), which resulted in an excavation depth ranging from about 27 ft to 39 ft (8.3 m to 12.0 m) below the existing ground surface.Subsurface ConditionsThe subsurface site investigation was performed in three phases by Al-Tamier Engineering Consulting Bureau. During Phase 1, a preliminary investigation was undertaken during the early stages of the project to obtain information about the general stratigraphy and groundwater level at the site. Phase 2 was performed to obtain subsurface information and design parameters, and Phase 3 was performed as a supplementary ground investigation to investigate unexpected ground conditions identified during Phase 2. In total, 14 boreholes were drilled to depths ranging from about 80 ft to 180 ft (24 to 55 m). The generalized subsurface profile is quite heterogeneous, and is predominantly composed of sand with silt and gravel that is underlain by limestone, calcarenite and claystone"

Jan 1, 2017

By Eric S. White, Thomas J. Sabourin, Khuram R. Mohib

"This paper presents the challenges associated with the design and construction of a steel sheet pile cofferdam supported with one level of grouted anchors in clean to silty sand with gravel. The initial assessment of the subsurface conditions indicated loose to medium dense soil with intermittent dense to very dense layers with no occurrence of cobbles and boulders. Sheet piles were proposed to be installed to a depth of 24 m below the ground surface to limit dewatering requirements for the cofferdam. During sheet pile installation, refusal of piles occurred at multiple locations forming passages for increased flow into the cofferdam. Modifications were made in the design of the dewatering system as a result of the increased flow. Finite element modeling was used to select the necessary modifications to the dewatering system within the cofferdam. Wells were installed based on the findings of the numerical model. Model simulations showed good comparison with monitoring of the field installed dewatering system.INTRODUCTIONIt is necessary to consider the impact of the ground water, subsurface stratigraphy, strength, and drainage behavior of the soil for the design and construction of cofferdams. This paper presents a case history of the construction of a cofferdam in Northern Ontario, Canada. The project consists of the construction of a powerhouse, intake, and tailrace which will generate around 28 MW of renewable clean energy by diverting water from New Post Creek through a power house and discharge into the Abitibi River. The focus of this paper is the dewatering and excavation support required to permit construction of the powerhouse. The layout of the cofferdam is shown in Fig. 1. The cofferdam for the powerhouse is rectangular in shape with sheet piles on all four sides intended to be driven to the design toe El. 101 m. The east and west walls have a length of 46.3 m. North and south sides are 47.6 m long; and in addition, two cantilever sheet pile walls bound the tailrace on the west side and two cantilever walls were installed on the east for construction of the penstock inlet. The ground surface in the powerhouse cofferdam area, before commencement of sheet pile driving, was brought to El. 125; the ground then slopes up to the East, toward New Post Creek, and the site is bounded on the West by the Abitibi River. 186 pairs of sheet piles were used to create the cofferdam and cantilever walls. The deepest excavation is to elevation 114.4 m. Within the west half of the cofferdam footprint, the base of excavation slopes upward at 3H: 1V to facilitate the tailrace discharge into Abitibi River.SOIL STRATIGRAPHYThe cofferdam design was based on the geotechnical investigation conducted by AECOM (2014) which included two relevant boreholes near the powerhouse footprint. The ground elevation at the time of investigation varied between 131 to 129 m. The material observed to the full depth of investigation was comprised generally of coarse to fine sand and gravelly sand or a sand matrix with gravelly inclusions. Some intermittent layers of clay and silt intrusions were also observed. Generally the soils grade finer away from the river. SPT N60 values were recorded in two borings during the field investigation with values reported from 3 to 92. The in-situ conditions ranged from compact to dense with some loose and some very dense zones. Figure 2 shows the variation in SPT N60 values with elevation."

Jan 1, 2017