Search Documents

The pile inspector is a critical element in the quality control process necessary for a successful pile installation project. This guide is intended to provide the inspector with a basic understanding of only one of the many components of this process - the pile driving hammer. Pile driving hammers are used to install both bearing piles for structure foundations and sheet piles (and soldier piles) as used in retaining structures. In a single document, this guide offers a general presentation of the operation of the more common types of hammers the inspector is likely to encounter. It should make the information in the contractor's hammer submittal for the project more understandable. It should also provide an appreciation for the importance of a properly operating pile hammer. Prior to the start of most pile driving operations, the contractor will normally furnish a submittal to the engineer giving the specific pile driving equipment that he intends to use on the job. This submittal should include the make, model, and type of the intended pile driving hammer or hammers and their operating characteristics such as ram weight, rated energy, operating speed, external power requirements and, other pertinent information. Frequently, the operating characteristics are provided in the form of the manufacturer's specification sheet. The engineer will review this information and when he is satisfied, approve it and pass it on to the inspector. The driving criteria will have been determined by the engineer or others (the geotechnical engineer, consulting engineer, contractor, etc.) from the results of static analysis (for minimum penetration), driving during a test pile installation, Wave Equation analysis, dynamic formula, pile instrumentation during driving, static load test, or a combination of these or other appropriate analyses. The driving criteria can be a minimum penetration of driven pile length (embedded length), or a minimum (or maximum) blow count per unit of penetration. The pile inspector should become familiar with this information prior to the start of the job and should understand or seek help to comprehend the terminology and intent of each specification.

Jan 1, 1995

By Karen Talbot, Noah Maier, Rob Jameson, Giuseppe Gaspari

A storage and drainage tunnel advancing below I-75 in Detroit, Michigan experienced sudden subsidence. The Tunnel Boring Machine (TBM) was damaged to the extent that its shield, cutting head and extensive interior components needed to be extracted and replaced along with several completed tunnel segments. The tunnel was 16 feet (4.9m) in diameter with crown over 79 feet (24m) deep at the time. The tunneling contractor immediately engaged their designers and specialty subcontractors to develop a scheme to access the machine and repair the tunnel. They required a shaft 99 feet (30m) deep, with unobstructed plan dimension of 50 feet (15m) to accommodate the large components that needed to be removed and replaced. This precluded the application of an internally braced excavation and instead earth support solutions focused on use of a compression ring. Since the completed tunnel section behind the TBM obstructed closure of the compression ring below its invert, this paper describes the innovative access shaft solution employed. A conventional compression ring was constructed using 5 feet (1.5m) diameter drilled shafts down to the tunnel crown. In front of, and to the sides of the tunnel heading, the secant shafts were extended to over 150 feet (46m) depth, creating a horseshoe of support extending 50 feet (15m) below the planned excavation invert. Larger diameter "King Pile" shafts were drilled immediately to either side of the tunnel, overlapped into each end of the secant "horseshoe". The king pile shafts, together with a heavily reinforced ring beam above the crown elevation, acted as a door frame to transfer hoop loads from the incomplete secant arc into reaction supports above and below the tunnel. These oversize king pile shafts were extended and socketed into rock over 70 feet (21m) below tunnel invert. Very tight installation tolerances were necessary to maintain secant shaft alignment to depths exceeding 150 feet (46m). The project operational, geotechnical, and quality data was managed and visualized using a custom GIS interface. This paper will present the design approach employed and review the construction and quality program selected to repair the tunnel.

Oct 1, 2022

Jan 1, 1985

By Ralphie Adams, Tiana Rasmussen, Ashley E. Shirer

Transmission line foundation designers must rely on limited subsurface information, from easily accessible locations, resulting in subsurface uncertainty, increased design risk and increased construction costs. This paper presents a different approach for foundation analysis conducted in mountainous and alluvial floodplains located northwest of Phoenix, AZ. The region is dominated by fault-bounded, northeast dipping mountain ranges, where rock types and drillability can vary from granite to intact basalt. The valleys between are comprised of “basin-fill” deposits ranging from conglomerates and cemented soils to lose alluvium. Recently deposited alluvial fills can vary in depth significantly from location to location due to erosion and deposition from active and historic hydraulic features. To limit the subsurface uncertainty for foundation design, a phased approach using geophysical surveys along with detailed geologic reconnaissance was employed. Both compression wave and shear wave velocities were measured in order to identify the depth and properties of loose erodible materials from more scourresistant cemented, conglomerate, and rock deposits. These analyses were used in combination with limited subsurface drilling and sampling to evaluate direct embedment steel pole foundations for over fifty structures. Post analysis results from limited construction drilling reports were used to assess this approach.

Sep 8, 2021

By Remco Offenberg, Marcel Bielefeld, Martijn van Delft

The question of the continued suitability of existing foundations arises when the function of the superstructure changes. This can occur when the superstructure is replaced or when the existing structure is expanded, leading to higher loads on the existing foundation. Quite often it is a challenge to define the suitability (with respect to integrity, bearing capacity or both). The lack of information on the existing foundation (such as pile dimensions, installation records, original soil investigation, design calculations, etc.) makes it frequently seemingly impossible to assess whether the foundation or foundation elements can be re-used. The paper outlines the tools available to an engineer to evaluate existing foundation piles for potential re-use. The paper illustrates the application of these tools through a few case studies from The Netherlands, including the evaluation of a 400 years old bridge foundation to address increasing traffic loads.

May 1, 2022

By Yazen Khasawneh, Osvaldo P. M. Vitali, Mohammad Nassim

Wind turbines are subjected to complex form of cyclic loadings with variable amplitudes and frequencies. The cyclic loading and the accumulation of plastic strains with the number of cycles will result in degradation of the foundation soil stiffness. The foundation stiffness degradation will result in a shift (reduction) of the fundamental frequency of the wind turbine. Although this issue is recognized in the guidelines for wind turbines foundation design, no specific provisions are provided in the guidelines to consider the long-term stiffness degradation. In this paper, a practical procedure to consider the long-term cyclic loading effects on the stiffness of wind turbine foundations in cohesive soil is proposed. The procedure is based on 3D FEM modeling and reliable empirical methods to estimate the stiffness degradation due to the cyclic loading. Using the proposed procedure, the long-term performance of the P&H tensionless pier foundation with and without a reinforcing collar at the top of the pier is assessed. The numerical results demonstrated that the long-term performance of the P&H tensionless pier foundation with a reinforcing collar at the top of the pier is outstanding with negligible long-term degradation of the foundation stiffness.

Sep 8, 2021

By Patrick van der Schaaf

"During 2016, foundation piling works were completed to allow for the construction of a production and storage/handling terminal in Rotterdam. It is there that steel foundations will be produced for offshore wind farms and the oil and gas industry. Several Dutch contracting companies were involved in constructing: foundations for an assembly hall, a barge quay and a deep-sea quay wall. For the hall foundations, cast in situ concrete vibro piles were created. Open ended steel casing piles were also installed due to very high cone resistances which made it impossible to perform cast in situ piles in certain areas. The quay wall was constructed with open ended steel casing piles in combination with sheet piles. A deep-sea quay wall was also constructed to provide enough storage area for the offshore mono piles. This project was unique and challenging due to the use of different foundation technologies in challenging circumstances and soil conditions. This paper will give an insight into the Dutch use of varying foundation piling techniques for deep-sea quay wall constructions. It can be concluded that even experienced local contractors can be surprised by variations in soil conditions. It will also show how the contractors adapted to the difficult circumstances.PROJECT OUTLINEThe project consisted of a barge quay near the assembly hall with a length of 500 metres, width of 42 metres and a height of 35 metres, and a deep-sea quay wall 480 metres in length. This paper concentrates on the foundation works for the construction of the deep-sea quay wall. The construction of the deep-sea quay wall consisted of a combination of open ended steel casing piles with a diameter of Ø 1420 mm and a wall thickness varying between 21 and 23 mm. The lengths of the steel casing piles varied between 32 and 37 metres. Between the steel casing piles triple PU 28 sheet piles were installed with lengths varying between 26 and 29 metres. In the Netherlands, a combination of open ended steel piles and sheet piles is known as a “combi wall”. For the deep-sea quay wall a steel combi wall was shored with steel H- section profiles that were driven in a raked position whilst being injected with grout, so called MV-piles. The MV piles for this project consisted of steel HEB 600 sections with lengths from 52 up to 59 metres and were installed with angles varying between 42.5 and 47.5 degrees. For a detailed overview regarding the project specifications reference is made to table 1 which is presented below."

Jan 1, 1900

By N. Schmitz

This paper explains how new digital solutions improve reverse circulation drilling operations. Upgrading field-proven reverse circulation drilling (RCD) rigs with new digital technologies enables semiautomated drilling, with upgrade options for fully automated & remote drilling. Key elements of the improvements are electrically controlled valve systems, process instrumentations, a state of the art machine controller and drilling operation via a touch control panel. Automation of core processes, such as adding drill pipes, reduces set-up times, increases machine uptime for drilling and as a result efficiency. While drilling, sensors provide continuous feedback, which is used to automatically adjust e.g. the weight on bit to the optimum; resulting in an increased rate of penetration and less wear and tear. While in the past hydraulic power packs (HPU) have typically been operated at a constant high-performance level with related high fuel consumption, a new interface between the machine controller and the power unit regulates the HPU performance exactly according to the actual drilling operation needs. This leads to significant fuel consumption reduction. The safety benefits of the digital improvements are the ability to remotely operate the rig in challenging site conditions via a mobile operator panel.

Sep 8, 2021

By Pancho J. Garza, Keith H. Dahlen, Chris A. Labye

"Design for reconstruction of the East Flagstaff traffic interchange project located in Flagstaff, Arizona posed particular challenges. The proposed design included construction of a nearly 50-foot tall mechanically stabilized earth (MSE) wall given rightof- way constraints and soft subgrade soils. The tight right-of-way, approximately 15 feet in certain locations, adjacent to existing structures limited the number of viable remedial alternatives to provide grade separation at the proposed bridge abutment without significant settlement. Preliminary analyses indicated the existing subgrade soils - consisting primarily of relatively soft silts and clays with decomposed pumice - would settle approximately 12 to 14 inches resulting in unacceptable wall deformation. Stone columns placed via vibratory methods (vibro-replacement) consisting of circular excavations which penetrate to firm bearing soils and which are filled with crushed stone were selected to densify the existing subgrade soils. The implemented mitigation measures helped limit settlement to less than one inch and allow for successful construction of the project. The project history - including site constraints, subsurface conditions, evaluation of remedial alternatives, stone columns methodology, and effectiveness of ground improvements - will be discussed.IntroductionThis paper describes the subsurface investigation performed for the reconstruction of the Business Route 40 (B-40) (Country Club Drive) and United States (US) 89 Traffic Interchange (TI) located within the city limits of Flagstaff, Arizona. This project is currently referred to as the East Flagstaff TI. The Project Site Vicinity Map is shown below.The former B-40/US 89 TI was considered ineffective in handling the current and projected volumes of traffic which transition from northbound (NB) B-40 to US 89 (both directions), as well as from southbound (SB) US 89 to SB B-40. The intent of the project was to reconstruct the TI to better accommodate projected traffic volumes. The project eliminated the existing ramps from both NB B-40 to SB and NB US 89. The new interchange includes a Tee intersection from B-40 to US 89. In order to accommodate this alignment, the profile of US 89 was raised several feet (on nearly the same as existing horizontal alignment) to match the elevated profile of B-40. B-40 was shifted just west of its current alignment to accommodate construction of a new, wider bridge structure which spans over Industrial Drive, the Burlington Northern Santa Fe (BNSF) railway, and old Route 66. South of the new bridge, B-40 transitioned back to the existing alignment just north of the I-40/B-40 TI. Within the project limits, both US 89 and B-40 were widened to three travel lanes in each direction."

Jan 1, 2015

By Steve Davidow, Ashely E. Evans, Peter M. Kandaris

"Annually thousands of deep foundations are constructed across North America supporting high voltage transmission line structures. However, a recent state of the practice survey by the Deep Foundation Institutes’ Electric Power Systems Foundation Working Group discovered that the electric power utility industry lacks consistent foundation design guidelines. The survey identified a wide variability in design assumptions, a minimal understanding of risk based analysis, and a need to standardize design methodologies. This paper summarizes the state of practice in electric system foundation design and proposes a framework for risk-based foundation design by accounting for uncertainty from both loads and resistances. Loads derived from electric system codes do not necessarily provide a compatible level of reliability for the design of foundations, as they are a mixture of probabilistic and deterministic values. Load uncertainty is derived from variability in weather conditions, structural models and material properties, typically accounted for by code derived overload factors. Resistance uncertainty arises from variability in natural soil properties, resistance models, subsurface construction techniques, material sampling methods, and limited observations. A consistent methodology is offered relating nominal resistance capacity (strength) to structure loads and service state criteria. Discussion also includes the need for risk-based assessments to account for non-structure load influences (fluvial loads, scour ground loss, liquefaction, etc.).INTRODUCTIONNearly 40 years ago the Electric Power Research Institute (EPRI) embarked on a major research effort to optimize reliability and economics of transmission line foundation design. Strategies focused on improvements in design models, site characterization, exploration strategies and testing to reduce uncertainty and variance in analysis. Transmission line engineers realized that safety and reliability advancements in design based on probabilistic approaches, with a focus on the unique nature of transmission line, could better control risk and cost.Some transmission line professionals took full advantage of these advancements, particularly where research led to improved software and models. Yet, even after two decades of extensive research, by 1995 the industry still had made little progress in changing design habits. The majority of designers were still characterizing sites via deterministic methods, using loads that may or may not relate to a consistent probability of occurrence, and applying a traditional global factor of safety approach (Phoon, et al. 1995). The following two decades have seen even greater developments in software and reliability-based analysis methods, but old habits seem to die hard as recent surveys show less than half of design professional quantitatively assess risk in their design process."

Jan 1, 2017

By Stephen Darmawan, Mahdi M. Disfani, Arul Arulrajah, Alireza Mohammadinia

Deep mixing using cementitious compounds is an in-situ method of ground improvement for improving the strength, compressibility of loose sand. Artificial light cementation can increase the stiffness of loose sands significantly and reduce the settlement of loose deposits. The increase in contact area between the particles with a thin layer of cementitious agent depends on the confinement and void ratio of the soil mass. Hence, the stiffening effect of cementation not only depends on the type and amount of cementing agent and inter-particular force chain of loose deposit but also depends on the stress level at the time of cementation. In addition, the cementation effect in loose deposits can be deteriorated at relatively low strain levels. Decementation softening can cause detrimental and irreversible impacts on the soil deposit. This study investigates the effect of initial confinement and subsequently the initial void ratio at the time of cementation on small strain behaviour and decementation softening of cemented loose sand under ko loading. The effect of inter-particular contact of sand particles based on the specific surface area and also soil density was also investigated by means of shear wave propagation. This study present insightful information on effect of primary consolidation stress levels, density of soil and cementation level on softening and collapse of loose deposits improved using deep soil mixing technique. Better understanding of soil-cement interaction by optimization of binder content for deep mixing activation can lead to increasing the level of confidence in using this technique in ground improvement applications.

Jan 1, 1900

By A. B. Cerato, M. K. ElSawy, A. Elgamal

"Helical piles are gaining popularity as foundations for new construction as well as retrofitting option for deficient foundations. More recently, large diameter helical piles are used to support structures in regions characterized with high seismic hazard. Even though they have proven to be viable in seismic areas such as New Zealand, where they experienced little damage during the Christchurch earthquake, the knowledge about their seismic analysis and performance is largely lacking. Therefore, there is a need for comprehensive study to evaluate their performance under seismic loading. The current objective of this study is to investigate the performance of helical piles through a full-scale testing program that was performed at the NEES/UCSD Large High Performance Outdoor Shake Table (LLHPOST). The experimental setup involved ten steel piles of different configurations installed in dry sand. The piles were loaded with different masses and were subjected to different earthquake signals to simulate different dynamic behavior. This paper compares the performance of different moment curve fitting methods used to interpret the test data. Furthermore, the effects of different frequency content of loading on the pile response is illustrated in terms of deflection along the shafts of tested piles with different configurations.INTRODUCTIONEarthquakes are a major hazard for structures situated in seismic regions, and dynamic loading must be a design consideration. Successful design of a foundation system entails providing a safe and economic foundation solution to resist earthquake loading. Different foundation options have been used to support buildings in high seismic regions. Helical piles represent a viable foundation option that offers several advantages in terms of ease of installation, lower cost and environmental impact, ability to approximate the axial capacity directly from torque readings and more (Perko 2009). However, they are not typically considered as an option in many seismic regions. Meanwhile, several buildings supported on helical piles in New Zealand have survived the Christchurch earthquake with negligible damage, which encourages performing further research to understand the behaviour of these piles under seismic loading.A helical pile consists of a steel shaft fitted with a steel helix/helices. The helical pile is installed by applying torque to its head via mechanical torque. Nowadays, helical piles are used in a wide range of applications such as foundations for light posts and residential houses. The static behaviour of helical piles has been studied extensively and is relatively well understood (Tsuha and Aoki 2010; Mittal et al. 2010; Sakr 2011; Elsherbiny and El Naggar 2013; El Sharnouby and El Naggar 2012; Elkasabgy and El Naggar 2015; Weidong et al. 2015 and Bagheri and Naggar 2015) However, the dynamic and seismic behaviours of helical piles is seldom investigated (Elkasabgy and El Naggar 2013). This underscores the knowledge gap currently present regarding the seismic behaviour of helical piles."

Jan 1, 2017

By Kyle R. Lackner, Jared P. Williams

"The Sutter Butte Flood Control Agency initiated the Feather River West Levee (FRWL) Program in 2010 to bring 35 miles of levee along the Feather River into compliance with applicable Federal and State standards for levees protecting urban areas. A combination of soil-bentonite cutoff walls, soil-cement-bentonite cutoff walls, and seepage berms will reduce flood risk by correcting under and through seepage deficiencies and remove more than 34,000 properties from the FEMA Special Flood Hazard Areas. The FRWL program includes a combined total of 7,744,803 square feet (SF) of cutoff wall planned to be constructed between 2013 and 2015. Cutoff wall construction methods to meet the design depths included conventional excavation to a depth of 85 feet and deep soil mixing for depths up to 120 feet. A key component of the FRWL program was the development of site specific mix designs using the design boring logs to evaluate the expected backfill gradation and permeability results. Issues that required a partnership between Contractors, Owner and Engineers included substantial Archaeological and Cultural Resource delays, significant depth changes due to a change in competent key, right of way acquisitions for abutting land, and the magnitude of the project in a resource limited industry.IntroductionThe Feather River watershed basin is located 50 miles north of Sacramento, CA and incorporates the agriculture producing communities of Yuba City, Live Oak, Gridley and Biggs. These communities are protected from flooding by levees that contain under-seepage and through-seepage deficiencies and were the cause of major failures in 1955, 1986 and 1997. The Feather River West Levee (FRWL) program was initiated by the Sutter Butte Flood Control Agency (SBFCA) in 2010. The long term objective of SBFCA is to correct the levee deficiencies and provide 200 year flood protection to more than 34,000 at risk properties located within the FEMA Special Flood Hazard Areas.Although FRWL contained a variety of construction components such as earthwork and pipe replacement, the slurry cutoff wall is the primary construction element for addressing under and through seepage deficiencies. From 2013 to 2015 approximately 6,649,210 SF of cutoff wall were installed using conventional excavation and deep soil mixing (DSM) techniques leaving 1,095,593 SF to be completed in 2016. The work was designed, solicited and constructed under two separate contracts, titled Project Area C and Project Area B&D. A summary of the contracts and cutoff wall quantities is presented in Table 1."

Jan 1, 2016

By Bengt H. Fellenius

It is a truism that in the design of pile foundations one must consider both capacity and settlement. As to capacity, most basic text books contain simple methods of design of capacity of single pile. More sophisticated methods are the subject of many journal papers. However, methods for design considering settlement of pile foundations are scarce. (Most confuse settlement with the movement due to load-transfer?the transfer of load from the pile to the soil). Furthermore, for both capacity and settlement, most methods include several simplifying assumptions regarding soil layering and neglect the effect of the frequently occurring fill and excavations, as well as changes of the groundwater table and pore pressure distribution. Therefore, the methods may provide qualitative results, but not quantitative. Because of this situation, pile design often appears as somewhat of a guessing game and a very subjective?and risky?occupation. This need not be. Pile foundation design is controlled by three factors: capacity, strength, and settlement requirements and these have been combined in a method called "the unified design of piles and pile groups considering capacity, settlement, and negative skin friction" (Fellenius, 1984; 1989), which method is summarized in this guide.

Jan 1, 1991

By Sunil Arora, Lisheng Shao, Chris Conkle

"The East Garden Grove - Wintersburg Channel located in Orange County, California, required upgrades along the levees to mitigate potential liquefaction and lateral spreading hazards. The Orange County Public Works designed soilcrete columns constructed between two rows of steel sheet piles along both sides of the channel between Graham Street and Warner Avenue (approximately 2,500 ft), and along an approximately 2,000-ft-long stretch of the south levee. The earthen embankment, approximately 13- to 15-ft high and damaged significantly by erosion, was then excavated to widen the channel to increase the channel flood conveyance capacity.The site is located within the Los Angeles Basin, underlain by several thousand ft of marine sedimentary strata. Uncontrolled fill materials were encountered to approximately 10 ft below ground surface, underlain by tidal and flood plain deposits. Groundwater was encountered at sea level, which is approximately 10 ft below grade.This paper will discuss site soil conditions, and the construction and quality control of soilcrete columns constructed by wet soil mixing; also, the paper will introduce the Drilling Index (DI) as a measurement tool, similar to the cone penetration test (CPT), to evaluate the soil strength in more detail. Finally, the statistical analysis of soil mixing strength distributions for the project quality control will be presented.INTRODUCTIONWintersburg Channel in Orange County, California, required ground improvements along the existing levees to mitigate potential liquefaction and lateral spreading under the site design earthquake. Orange County Public Works designed and developed a cellular pattern of soilcrete columns sandwiched between two rows of steel sheet piles along both sides of the channel between Graham Street and Warner Avenue, and adjacent an approximately 2,000-ft-long stretch of the south levee (Fig. 1). An earthen embankment approximately 13 to 15 ft high, damaged significantly by erosion, was then excavated to widen the channel and increase the channel flood conveyance capacity.Stiff, soilcrete cellular wall structures can reduce the earthquake-induced cyclic shear stress ratio (CSR) in the soil within the cells, thus preventing excess pore water pressure build up which may trigger soil liquefaction. For this project, approximately 6,700 soilcrete columns were constructed in a cellular pattern to an approximate depth of 40 ft. All of the soilcrete columns are 3 ft in diameter with the design unconfined compressive strength (UCS) of 150 psi."

Jan 1, 2015

By David A. Jack

The Mission Valley Viaduct is located in San Diego, California. This structure is the intersection of Interstate 8 and 805. The project consists of the main viaduct, 8 connecting ramps, and one highway overpass. This job was originally built back in the 70's. After the Loma Prieta Earthquake in 1989, Caltrans began an aggressive program to seismic retrofit all of its bridges throughout the state. Most retrofit designs required major upgrades to the existing footings. These footing upgrades consisted of either driven or drilled shaft piling. The existing footings of the Mission Valley interchange were supported on driven H pile. The soils throughout the site were dense sands and gravels, cobbles, occasional boulders with a dense sandstone bearing strata, which varied through out the site. It was this sandstone strata that the engineers designed their pile tips around. High ground water in sandy soils created a high probability of liquefaction in all of the upper stratas.

Jan 1, 1998

By Ali S. Fayad

"In June 2014, Orange County Flood Control District (OCFCD) completed construction improvements of the East Garden Grove-Wintersburg Channel for a price of $42 million. Instead of the pre-existing traditional trapezoidal levee, the channel was improved with a vertical compact levee. Dubbed Soil-Mix-Sandwich (SMS), this geo-structural and environmental solution for coastal channel improvements, underlain by liquefiable soil strata, was both a design and construction innovation. It employed Deep Soil Cement Mixing (DSCM) within the confines of a hydraulically-pressed (Giken Method) sheet pile duo. SMS was unique because it incorporated both subterranean and supra-dredge-line soil mixing within a very narrow workspace. Its DSCM pattern aimed at optimum densification of the workspace and was confirmed during the construction process. It availed the DSCM sub-contractor (Hayward Baker Inc.) the opportunity to demonstrate the fitness of their huge wet-mixing machinery within a very confined access-area and introduced approximately 70,000 cubic yards of DSCM within a limited 15 foot workspace width that stretched for a mile. The sheet pile duo created a construction-enclosure that became a stay-in-place load resisting system. PROJECT CHRONOLOGY AND LOCATIONAn Orange County Flood Control District (OCFCD) project-report was commissioned to study the East Garden Grove Wintersburg channel (OCFCD facility # C05). The report examined the hydraulic conveyance of the C05 channel and was concluded in 1994 by Williamson & Schmidt. The project-report did not encompass extensive geologic studies; but it provided several alternatives for channel improvement. It recommended a single row of sheet piles as the preferred alternative for the downstream reach.The most downstream reach of the C05 channel is located in an environmentally sensitive area, in City of Huntington Beach, California, USA. Its site includes seismic chasms that surface within the C05-footprint (the Newport- Inglewood tectonic fault). Extensive deposits of liquefiable soil exist beneath the channel. Furthermore, tidal-influence prevails against the channel levee. Implementation of a successful design for channel improvement emerged after several traditional concepts were deemed unacceptable by geotechnical consultants. OC Public Works (on behalf of OCFCD) was in need of a design and construction technique that mitigated many associated risks. From these circumstances, Soil-Mix-Sandwich was born and was referred to in the rest of this discussion as SMS. OC Public Works required the SMS design concept to undergo verification by independent geotechnical consultants. SMS chronology from conception to construction can be summarized as follows:"

Jan 1, 2015

By Phillip E. Glogowski, N. Catherine Bazan-Arias

Steel foundations can be designed to cross-sectional configurations ranging from triangular and square to other multi-side shapes. Adding lateral extensions (hereby called wings) along the length of the steel stem can increase the foundation’s uplift, torsional and lateral load capacities. DiGioia Gray staff developed a methodology for the optimal design for multi-facetted, winged deep steel foundations. A finite element (FE) model is used to represent the steel components and the nonlinear subsurface behavior. The geometry of the foundation can be complex; thus, an optimal design needs to be fine-tuned to the specific site conditions. We created a pre-processor tool to generate the FE model including varying values for the number and size of wings, depths of embedment, reveal/stickup heights, top plate geometries, and subsurface profiles. The analytical model has been partially validated through full-scale testing and the methodology has been applied to two installed projects to date.

Sep 8, 2021

By Gustav Jahner, Michael Baltrusch, Norbert Hoffmann

Near the port city of Whitby in the north-east of England, Anglo American (AA) is setting up the deepest mine in the UK, which will have a depth of 1,500m. The purpose of the project is to extract and transport polyhalite, both underground, and to market it globally. As part of the construction works, BAUER Technologies Ltd, the UK subsidiary of BAUER Spezialtiefbau GmbH, constructed three different shafts using the diaphragm wall technique, with depths of up to 120m. In order to ensure the specified vertical tolerance of maximum 200mm, several measurement methods were applied, and the results were documented in a 3D model. Complex de-sanding plant technology and specially developed polymer products were adopted to regenerate the trench supporting bentonite-slurry.

Sep 1, 2022

By Thomas J. Kennedy, Michael D. Bennett

The study of geotechnical history is well-established. Most geotechnical practitioners, teachers, and graduate students have some grasp of the origins of the field. However, this understanding often consists of a jumble of names and anecdotes. This paper discusses how a deeper comprehension of geotechnical history can benefit academia and practice alike and describes how the authors have begun a wide-ranging study of the subject. The paper reviews the dual-track methodology the authors have generated for the study, which consists of written articles about different works in geotechnical history and a database tracking how often pieces have been cited in geotechnical literature. The first technique has shed light on aspects of geotechnical history such as the connection of the Darwin family to the origins of geotechnical engineering, the St. Francis Dam failure of 1928, and the rivalry between theoreticians and practitioners in the early days of the field. The second has helped quantify subjects such as the outstanding contributions of Karl Terzaghi, the disagreements between Terzaghi and Donald Taylor, and the specialization of the field over time. The paper concludes by discussing the authors’ planned future work on geotechnical history.

Oct 1, 2022