Search Documents

By Tatiana Tronda

"The territory of Belarus is characterized by nonhomogeneous ground conditions. In some cases soft ground layers can reach tens of meters in depth. Application of piles and other conventional foundations is rather difficult and expensive in such complicated conditions. Alternatively for the first time dry concrete columns were applied to improve the saturated soft soils at two sites. As there is no design methods for calculation of bases improved by dry concrete columns static penetration and static load tests were carried out to check the bases on availability. Considerable increase of toe resistance and Young modulus was achieved for all types of soil. Practical application, technology and test results are described in the paper. According to comparative calculations the cost of foundations on the base improved by dry concrete columns can be 32-75% lower than the cost of conventional pile foundations depending on ground conditions.INTRODUCTIONPile foundations, sand cushions or dewatering are usually applied in complicated ground conditions which are caused by presence of saturated soft soils. If the depth of soft soils reaches 20 m or more, conventional foundations have limited application, high labor and construction cost. A rational solution in such conditions is a ground improvement of upper soft soils. It allows the loads to be transferred on upper ground layers and the stresses to be dissipated considerably before reaching underlying soft ground layers.One of the effective ground improvement methods for saturated soft soils is the reinforcing by dry concrete columns (Fig. 1). The method allows saturated soft soils to be compacted and be drained at the same time. As a result strength and deformation characteristics of natural soils improve (Tronda 2013, ?????? 2014).Unfortunately, there is no design and computing methods for the ground improvement by means of dry concrete columns. However, at present the methods are under development on the basis of theoretical and experimental researches.TECHNOLOGYThe dry concrete columns are fulfilled in pressed wells according to technology of vibrostamped piles. Wells are pressed by vibratory hammer with the closed ended casing (Fig. 2) that provides compaction of surrounding soft soils. Then the casing is filled with dry concrete mix (Fig. 3). The casing end remains on the design depth and the casing is removed by vibratory hammer. The removing of the casing with vibration enables compaction of dry concrete mix inside the well. Dry concrete mix drains surrounding saturated soft soils improving its properties and the compaction speeds up the consolidation process. Over time the dry concrete columns fasten absorbing water from surrounding saturated soft soils that is need for hydration of cement (Fig. 4, 5)."

Jan 1, 2016

By Reza Y. Khaksar

Presented is a rigorous solution for the three-dimensional stability analysis of vertical shafts (excavations) subjected to the self-weight of the soil based on the upper-bound theorem of limit analysis approach. A rigid-block translational collapse mechanism is assumed, with energy dissipation taking place along planar velocity discontinuities. This mechanism is optimized to obtain the critical failure mechanism giving the lowest factor of safety for stability of shafts. Based on comparisons with other solutions, the method is generally found to be accurate in predicting the stability of vertical cuts.

Jan 1, 2006

By Gordon Chen

The Block 37 Chicago Transit Authority (CTA) Tunnel Construction Project was originally designed by STV to connect Blue Line subway in North Dearborn Street and Red Line subway in State Street in the downtown Chicago Area. The project was proposed using tunnel mining techniques combined with steel pipe jacking and fiber glass rebar soil reinforcement. Weidlinger Associates, Inc. (WAI) and Kiewit Construction Company proposed an alternate design using open cut construction technology. WAI designed a complex temporary excavation support system using Soldier Pile Tremie Concrete (SPTC) walls and Soldier Pile Lagging walls supported by cross lot/corner bracing elements. Below the top of the existing tunnel, a top-down construction technique was utilized. A steel temporary traffic decking system at top of the excavation site served as the daily street traffic function as well as the first level of bracing for the support of excavation. The project encountered great challenges of soft clay conditions in downtown Chicago, numerous existing utilities in the excavation site and the requirements of protection for a number of historical buildings nearby as well as the protection of the city streets. The construction was successfully completed at both State Street/Washington Street and Dearborn Street/Randolph Street. The monitoring system showed that ground movement and adjacent building settlement was kept to a minimum during construction.

Jan 1, 2009

By A. L. Garassino

Dans cet article on parle sortout de l'approche de calcule pour les pieux charges horizontalement avec particuliere reference aux curbes p-y et è une solution semi-empirique qui prende en consideration les variations typiques du module du sol avec la deformation obtenue par les données expérimentales. 1. INTRODUCTION The analysis of the piles under lateral loads depends very strictly from the pile stiffness and geometry, from the soil type and from the strain field. Different approaches were adopted in solving the problem. Some Authors developed methods for estimating the ultimate lateral resistance of piles and pile groups by conventional static approaches, as the Brom's widely known (1964) or by the plane strain solution developed by Davis (1961) or by empirical engineering con­siderations l

Jan 1, 1994

By Chu E. Ho, Paul Napoli

A new waterfront park was developed on Long Island in close proximity to the East River and Newtown Creek. The existing ground consisted of fill over soft organic clay, medium dense silty sand, glacial till and schist bedrock. The ground was initially raised to preload the underlying soft soils to stabilize the ground in preparation for site development. The ground was subsequently cut down to temporary grades for installation of foundation piles for the overlook structures and construction of reinforced concrete cantilever retaining walls forming pathways located adjacent to the water bodies. The retaining walls were located in two rows at different elevations along the sides of a steep embankment. Where the pathways converge, some of the walls were too close to each other, and were redesigned as a combined U-wall with a common base slab. The individual retaining walls were designed for adequate bearing, sliding and overturning resistance. Ground anchors were installed to enhance global stability of the retaining walls. This paper presents the design considerations for the retaining walls for various loading conditions, and evaluation of the trial and proof tests for the anchors. INTRODUCTION The New York City Master Plan included the transformation of an approximately 30-acre parcel of land in Long Island City, Queens, New York from a former manufacturing zone into a residential, commercial and recreational zone for middle-income community. The site was located at Hunters Point South along the eastern shoreline of the East River and Newtown Creek (Figure 1). The development included low to high- rise residential buildings, a public school, and retail structures. Open spaces were provided along the East River and Newtown Creek waterfronts in the form of a continuous park providing for recreational and community-related activities. Waterfront structures included small park buildings, walkways and viewing platforms. The shoreline was surrounded by revetments as part of the flood mitigation strategy. The project involved extensive site re-grading and several retaining walls were constructed. The earthwork volume amounted to approximately 47,000 cubic yard of imported fill and 93,000 cubic yard of cut. The exposed height of the retaining walls ranged from 3 to 15 feet. This paper focuses on the design and construction of the retaining walls for the project.

Jan 1, 2019

By Vishal Pathak, Shailesh A. Godhuly

Ground Modification System in terms of Jet Grouting for soil strengthening and mass stabilization was engaged for a power plant project in an international power project, engineered by L&T-S&L. The site Geology consist of cohesionless type of sandy alluvial deposits (silty fine sand) as the main formation. Ground water table is encountered at shallow depth. Geological interpretation is done using soil investigation data along with CPT’s. This paper discusses design and implementation of jet grout technique to improve the mechanical behaviour of soil. To distribute load evenly from superstructure, a layer of growmast (drainage blanket) is laid above jet grout columns. Settlement evaluation is done using Finite element analysis with Plaxis 2D and Settle 3D. In the project, selected equipment foundations are resting on jet-grout columns including vibratory equipment like 144MW Gas Turbine etc. The project has been commissioned in September 2021 and operating with full capacity.

Sep 1, 2022

By Donald A. Bruce

Various types of contemporary Deep Mixing Method (DMM) techniques have been used in the United States since 1986. Such techniques owe their origins to Japanese and Scandinavian developments, which began almost three decades ago. The growing demands of urban infrastructure development and rehabilitation have created a very active and rapidly expanding market demand in the United States especially since the early 1990s, and there is a clear need for a new and fundamental review of the surprisingly large number of DMM techniques that are being used domestically, or are available in other parts of the world. Following a summary tracing the historical development of DMM, and a generic classification of applications, the paper provides a review of each of the many different proprietary methods, which the authors have identified during preparation of an international survey funded by the Federal Highway Administration (FHWA). Data are also provided on commercial aspects of the various DMM techniques worldwide.

Jan 1, 1998

By M. Tominaga

An industrial port complex was constructed on the west coast of Leyte Island The work was started in December 1981 and completed in May 1984. This port complex includes a 665 m long wharf and can accommodate vessels ranging from a 60,000 DWT ore carrier to a 4 000 DWT general cargo ship. It now handles materials for and products from a copper smelter with an annual capacity of 130,000 t and a fertilizer plant with an annual capacity of 900,000 t. The Wharf structures consist mainly of interlocked steel pipe piles, steel sheet piles and steel pipe Piles. Material handling equipment such as unloaders, shiploaders, etc. were installed on the wharf. Site survey, planning, engineering design and construction aspects of the port development are discussed in this paper with particular emphasis on the wharf structure.

Jan 1, 2010

By Jakub Szary

Excavation and shoring adjacent to the above-grade Gilmore train station and elevated guideway was undertaken in 2019. A perimeter secant pile cut-off wall was constructed to a depth 37 m (121 ft) below ground surface consisting of 1.0 m (3.3 ft) diameter drilled piles spaced 750 mm (2.5 ft) on-center, tied back with soil anchors, and reinforced with W610 steel sections every 4th pile. A bracing/jacking system was also constructed to support 3 free-standing guideway caissons within the excavation. An automated instrumentation program was installed to monitor movements of shoring walls and train infrastructure in real time and consisted of a robotic total station, inclinometers, tiltmeters, strain gauges, extensometers, and anchor load cells. Baseline monitoring was able to establish diurnal and seasonal movements within the structure, strongly correlated with temperature. The system actively monitored various shoring elements and train infrastructure in real time and alerted the project team when values exceeded predetermined threshold values. Remote reconfiguration of the automated system allowed for more frequent monitoring during jacking of Pier 29 in March 2022. Monitoring data was in agreeance with on-site manual surveying results and jacking dial gauges, and proved to be a reliable monitoring system for construction applications.

Sep 1, 2022

By Steven R. Musselman

The bending strength and flexural stiffness of a micropile at its threaded connection is less than its intact strength and may fail due to thread slippage or by fracture through the pin (reduced cross-sectional area of male threads in the threaded zone of the casing). The mode of failure depends on the reduction in cross-section necessary for machining the threads, and details of the threaded connection such as the length of threaded connection, size and shape of threads, and the thread density (threads per inch). Based on data from bending tests conducted on 9-5/8 inch diameter micropile casing, a method has been developed to predict the ultimate moment capacity and initial bending stiffness of round threaded micropile connections. Two modes of failure were observed from four-point bending tests conducted at the University of Illinois on 9-5/8 inch casing with round threads. Threaded micropile casing connections with an effective thread length of 1.35 inches typically failed by slippage at the threads (jump out), while connections using an effective thread length of 1.89 inches failed by fracture of the pin. These two failure modes were described by W.O. Clinedinst in his report to the American Petroleum Institute on tension tests of threaded pipe casing. Clinedinst developed an empirical formula to determine the tensile strength of threaded connections. A method to predict moment capacity for threaded micropile connections by modeling the micropile cross-section and applying Clinedinst?s equation to determine the max tensile stress along the threaded connection while satisfying force equilibrium is proposed. The predicted moment capacity for threaded connections using this approach is within ten percent of measured for both modes of failure observed from the bending tests.

Jan 1, 2007

By James L. Christensen, Gregory Sanchez, Michael P. Walker

The Fogg Museum expansion project required excavation and construction in a congested urban area in Cambridge, Massachusetts. A soldier pile tremie concrete (SPTC) wall provided the support of excavation and now serves as the permanent basement wall of the new expansion of the museum. The existing Fogg museum had a single basement level. The new expansion has a two-level basement for new exhibit space and an amphitheater. The east side of the site is about 20 feet above the basement level of the existing Fogg structure which resulted in a significant unbalanced load that needed to be resolved without damaging the original Fogg structure. The SPTC wall was supported with a combination of tiebacks and internal bracing. The final depth of the excavation was about 40 feet below street level. Strict movement control was imposed because the existing museum contained an Italian Renaissance-style courtyard. The southeast corner of the SPTC wall had to accommodate underpinning of an historic concrete ramp which was ultimately incorporated into the expansion. Challenges during construction included excavating the SPTC wall panels up to 12 feet into argillite bedrock which had occasional diabase dikes and sills. The following topics are discussed in more detail after a general project.

Jan 1, 2015

By Maurice Bottiau

When dealing with displacement auger piling, some general and fundamental issues have to be considered, irrespective of the system. More than with other pile types, the interplay between the soil conditions and the design and execution is of outstanding importance. This paper intends to address these issues and to summarize some critical matters in terms of design, execution and control such as : ? Importance of a reliable soil investigation ; ? Summary of the design as it is addressed in Europe for this category of piles ; ? Criteria for a good choice and control of the correct asset of the piles ; ? Importance of the concreting phase; ? Relation between the power and the engine characteristics of the drilling equipment with the final bearing capacity. For each of these issues detailed examples will be given as well as results of load tests and in-situ control during execution.

Jan 1, 2003

By Dan Brown

Improvements in construction equipment and techniques in recent years have made possible the use of drilled shaft foundations in diameters and lengths not previously considered practical or feasible. Many highway bridge and other structures are now routinely founded on drilled shafts which are 8 to 12 feet in diameter and extending over 200 feet in depth below grade. There are unique challenges associated with constructing such large and deep cast-in-place foundations and engineers should be aware of the special needs associated with site investigation, construction specifications, material requirements, and quality assurance. This paper outlines a number of special considerations for these foundations, along with strategies that may be employed to improve the reliability and quality of large drilled shaft foundations.

Jan 1, 2013

By Shoichi Tsukuni, Akihiko Uchida, Kazuo Konishi

"In order to investigate the effect of grid-form deep mixing walls as a countermeasure for liquefaction damage to roads and private houses in Urayasu, Japan, three dynamic centrifuge model tests were conducted. Urayasu is located in the Tokyo Bay area, and private houses in the city incurred severe damage due to liquefaction during the 2011 Tohoku earthquake. In grid-form deep mixing walls design, the distance between grid-form walls is critical to prevent liquefaction. This study clarifies the relationship between the settlement of private houses and the distance between grid-form walls under the conditions that exist in Urayasu.INTRODUCTIONMany private houses in Urayasu, Japan suffered severe damages due to liquefaction during the 2011 Tohoku earthquake (Photograph 1). Fig. 1 shows the location of Urayasu and the maximum acceleration of the observed seismic waves in the Tokyo Bay area. At Urayasu, the duration of the seismic waves (hereafter called the Urayasu Wave) was about 2 min. The maximum acceleration was 1.57 m/s2 (Fig. 2), which is relatively small. The damages occurred in the land reclamation areas that consist of loose sand with an SPT-N value less than 10.To prevent liquefaction in future, it is necessary to adopt suitable countermeasures in the areas where many private houses suffered severe damages. Grid-form deep mixing walls are one such countermeasure. Fig. 3 and Photograph 2 show grid-form deep mixing walls. Walls are constructed using the deep cement mixing method. Fig. 4 shows a plane view of planned grid-form deep mixing walls for roads and existing private houses in Urayasu."

Jan 1, 2015

By William F. Anderson

A series of pile load tests (maintained load tests, constant rate of penetration tests at different rates, and statnamic tests) was carried out on an instrumented model pile installed in clay beds prepared by consolidation of a slurry in a calibration chamber. The total load, shaft resistance and end bearing during the pile load tests were investigated. Following this, alternative methods of deriving the static load-settlement curve from a Statnamic test in clay taking into account damping effects have been proposed. These methods have then been used to interpret a statnamic test on a full size instrumented pile installed in a stiff glacial till.

Jan 1, 2006

By T. Soejima

In recent years, there has been a tendency in the field of foundation piling works to utilize piles of greater bearing capacity in order to meet increasing height and weight of modern building as a means of saving of piling cost. To satisfy these requirement, a new technique for large diameter bell bottom cast-in-place piling has been developed utilizing multi-head reverse circulation drilling system.

Jan 1, 2010

By J. M. Mitchell

Kuala Lumpur, Malaysia is underlain by karstic limestone. Firm clays, mudstones and siltstoncs of the Kenny Hill Formation overlie the limestone for about two thirds of the city. The remaining third has deep deposits of very soft alluvium, or tin mining slimes, overlying the limestone. It is only recently that large buildings have been constructed in the area. Arup Jururunding have been concerned with several projects located on the limestone, although space here only permits the description of four sites in detail. The experience has allowed the development of a design approach for the foundations. The aim is to make the architectural scheme compatible with the geology. This is not always possible, and examples are given of both situations. The case histories give examples of compensated foundations, and piled foundations include steel H-piles, precast concrete piles, micropiles, bored piles with rock sockets, and barrettes up to 90m deep.

Jan 1, 2010

By Dzianis Proshchanka, Yoshi Izumi, Koji Mitani, Ayuna Kitaura

"A new pile driving and drilling navigation system has been developed. It utilizes the commonly used surveying total station, combined with an innovative reticle. Conventional crosshairs have been replaced by a concentrically circular reticle called Baum. It allows for easily performed measurements of central axes of cylindrical objects such as piles, chimneys, electricity poles, etc. This provides several significant advantages compared to other existing systems. It is cost-effective as only one operator is required to control deviations in positioning and inclination. Furthermore, repetitive reinstallation of the instrument is not required for every pile driven or hole drilled. It is also a safer method, as workers have no need to be near a pile driver or drilling machine to perform the measurements. With Baum Station, necessary measurements can be performed away from the actual work area. Moreover, it is highly accurate with real-time solutions, as three-dimensional orientation information for the pile/drill is obtained simultaneously with the pile being driven or the hole being drilled. This allows for the highest levels of precision-control and correction to minimize eccentricity of the intended center positioning.INTRODUCTIONBackgroundIn foundation construction for structures, pile foundations are widely used for deep bearing strata. There are two patterns to driving piles: vertically or obliquely to the ground. The shapes of the piles are normally cylindrical. Vertical pile foundations are employed as the foundations of many structures due to their high workability. There is a problem however, which is that this method does not bear measurement data as construction accuracy is visually checked. On the other hand, tilted pile foundations are rarely employed because it is too difficult to ensure construction accuracy. In addition, commonly used percussion methods create noise and vibrations when the piles are hit, while there are advantages that thinner piles are available, ensuring earthquake-resistance, as tilted piles curb horizontal displacements of structures, which may be caused by earthquake ground motion. However, current requirements of cost reduction bring professional attention to tilted pile foundations, which can be driven reasonably and economically with much research of tilted piles having been carried out to improve their capacity. Also, a method of screwing piling has been developed, which produces small amounts of noise and vibrations. This method has solved tasks of workability and environmental burdens, and is becoming more and more common. However, there is a necessity to develop a method to accurately measure angles of piles’ axes in order to drive piles into the ground with appropriate angles. It is also expected to find out a way to control construction information, such as correction amount and driving record."

Jan 1, 2017

By Brian P. Waagner

Construction law in general and the law of deep foundations in particular continues to develop rapidly, particularly in the areas of risk allocation. Public and private owners are increasingly using contractual disclaimers to shift the risk of differing site conditions to contractors, and courts are increasingly willing to enforce these contractual devices. Perhaps also in an effort to control costs, public and private owners are turning to design-build contracting techniques. While design-build offers many advantages over traditional project delivery systems, it does not answer all of the risk-allocation questions that frequently arise. Even in design-build, problems with unanticipated subsurface conditions and defective design are not easily addressed. Finally, developments in electronic commerce present the potential to transform the construction industry.

Jan 1, 2002

By Susheel R. Kolwalkar

A significant increase in the side shear capacity over a period of time is often observed in case of driven piles. This phenomenon is referred to as ?setup? or ?freeze?. This phenomenon cannot be predicted based on the knowledge of the engineering properties of soil. Different kinds of mechanisms have been proposed in order to explain set-up in cohesive soils. In engineering practice, set-up is incorporated in design on the basis of empirical formulae and depends to a large extent on personal experience and judgment of the design engineer. Set-up is a natural process which cannot be accelerated by any existing practice. A research was initiated to investigate the mechanism of pile set-up in clayey soils and explore the possibility of accelerating the set-up process by an electro-kinetic method. The system chosen for the present study consists of a prototype steel pile driven in kaolinite clay. A laboratory test program was developed at Cleveland State University in order to meet the goals of the proposed research. Results obtained from these tests are very encouraging and show pile capacity increase of 200% within the first 5 days of electric gradient application versus those that experience natural set-up. In this paper, theoretical considerations and laboratory test results are presented and discussed.

Jan 1, 2008