Search Documents

By Chu E. Ho, Paul Napoli

This paper presents the performance of nineteen open-ended steel pipe piles driven through highly variable overburden soils into glacial till and schist bedrock. The piles were 16 inches in diameter and 0.656 inches thick, with yield strength of 50 ksi. The piles were designed for a service capacity of 250 kips and were driven to achieve an ultimate geotechnical capacity of at least 500 kips. Due to the large variation in the ground conditions, installed pile lengths ranged from 25 to 66 feet. Some piles were driven to refusal on the bedrock while others were terminated at final driving resistance of 2 to 7 blows/in. Two piles were suspected to be plugged during driving while others did not. Each pile was instrumented with strain gages and accelerometers near the pile top, and observed using a Pile Driving Analyzer (PDA) to provide preliminary guidance on pile capacity achieved at end of initial drive (EOID). The influence of plugged and unplugged pile toe conditions on the interpretation of pile capacity was investigated using Case Pile Wave Analysis Program (CAPWAP). Characteristics of driving energy, compressive and tensile stresses developed in the steel pipe piles, and the resulting pile deformation behavior are discussed. INTRODUCTION The Hunters Point South redevelopment in Long Island City, Queens is one of New York City’s major efforts to transform former manufacturing zones into mixed developments for the middle-income community. The site is located along the eastern shoreline of the East River and Newtown Creek. The development included low to high-rise residential buildings, a public school and retail structures. Open spaces were created along the East River and Newtown Creek waterfronts in the form of a continuous park providing for recreational and community related activities. Waterfront structures included small park buildings, walkways and viewing platforms with the shoreline protected by revetments as part of the City’s flood mitigation strategy. The project was implemented in two phases, with completion of construction for Phase 1 in 2013 and Phase 2 in 2019. Based on available historical information, extensive reclamation took place between 1855 and 1898. After 1951, changes to the shoreline were made along the East River, including the removal of reclaimed land along the northern portion of the project site to allow for docking facilities. By 1977, these facilities had been demolished and backfilled to form the current shoreline configuration. The present site was temporarily used as a parking lot with stockpiles of fill mixed with construction demolition rubble, rip-rap and boulders of varying heights across the site. The existing ground surface varied significantly up to approximately 25 feet difference in elevation. The stockpiles were removed and the site was re-graded during final development of the project. This paper discusses the foundation design challenges due to the loose overburden soils and potential obstructions within the fill material, in particular, the issues relating to installation of open-ended steel pipe piles through the ground conditions encountered on site.

Jan 1, 2019

By Gordon Chen

The Block 37 Chicago Transit Authority (CTA) Tunnel Construction Project was originally designed by STV to connect Blue Line subway in North Dearborn Street and Red Line subway in State Street in the downtown Chicago Area. The project was proposed using tunnel mining techniques combined with steel pipe jacking and fiber glass rebar soil reinforcement. Weidlinger Associates, Inc. (WAI) and Kiewit Construction Company proposed an alternate design using open cut construction technology. WAI designed a complex temporary excavation support system using Soldier Pile Tremie Concrete (SPTC) walls and Soldier Pile Lagging walls supported by cross lot/corner bracing elements. Below the top of the existing tunnel, a top-down construction technique was utilized. A steel temporary traffic decking system at top of the excavation site served as the daily street traffic function as well as the first level of bracing for the support of excavation. The project encountered great challenges of soft clay conditions in downtown Chicago, numerous existing utilities in the excavation site and the requirements of protection for a number of historical buildings nearby as well as the protection of the city streets. The construction was successfully completed at both State Street/Washington Street and Dearborn Street/Randolph Street. The monitoring system showed that ground movement and adjacent building settlement was kept to a minimum during construction.

Jan 1, 2009

By Ivan Jackson Madura

The new Paradisus Coco Beach Resort in Rio Grande (PR) is located on an old swamp area, which has been filled with relatively clean to silty sands. The swampy deposits consists of organic silts, peat and loose fine to medium sand and silty sand. The project requires the placement of 1.0 to 1.5 meters of additional fill together with the construction of light structures. The need for the fill will trigger the development of settlements in the underlaying weak and compressible stratum. Furthermore, the susceptibility of the loose sand to liquefaction during an earthquake was considered. This paper describes the soil improvement by means of vibro-replacement, the purpose of which was threefold: reduction in total and differential settlement, acceleration of settlements during the surcharge period and densification of the loose sand to reduce its liquefaction potential. The predesign is presented together with relevant construction details of the preliminary trial areas from which the final column diameter and grid spacing were derived. Instrumentation together with settlement observations during the surcharge period are presented as well and compared with the initial predictions.

Jan 1, 2002

By Kirk A. Mcintosh

Augered, cast-in-place (ACIP) piles have been utilized in the United States for a wide range of projects since the 1950's. Due to the cast-in-place nature of the installation method (and lack of a driving criteria); however, ACIP piles have not been readily accepted by some practicing geotechnical and structural engineers. Since ACIP piles were initially developed, the installation equipment and techniques have been improved and refined and the number of experienced contractors has significantly increased. Over the past 10 to 15 years, the pile type has experienced significant growth in the United States (particularly in Florida) because engineers have become more knowledgeable and comfortable with its use. The Miami area, in particular, has experienced considerable growth in the utilization of ACIP piles primarily due to their usage on the $1 billion Miami Metrorail System project in the early 1980s. The economic advantages over other deep foundation types, coupled with some unique installation advantages, have shown that ACIP piles can be a viable foundation alternative on many projects. Even though ACIP piles have gained respect in the private sector, the pile type has generally not been readily accepted by government transportation agencies. The reluctance to readily accept this foundation type stems primarily from the quality assurance aspect of cast-in-place pile construction. Additionally, there has not been much research activity on this foundation type, technical papers, formal associations (other than the DFI), or a concerted effort to standardize the industry. This paper serves to discuss the state of practice for ACIP pile installation in the state of Florida.

Jan 1, 1997

By Joseph T. Coe, Siavash Mahvelati, Philip Asabere

Characterization of existing foundations remains an important issue as foundation reuse and rehabilitation continue to garner increased attention. In the case of unknown foundations, geophysical and nondestructive testing (NDT) methods have been utilized in the past to evaluate foundation geometry and could serve as useful tools in the case of foundation reuse. A comprehensive study was initiated in the late 1990’s and early 2000’s that evaluated the effectiveness of the available geophysical and NDT technologies to characterize unknown foundations for scour evaluation purposes. At the time of that study, the Multichannel Analysis of Surface Waves (MASW) geophysical method was in its infancy and not widely used. Since then, MASW has become increasingly prevalent in geotechnical applications as the method presents a number of potential advantages when characterizing the subsurface, including rapid testing, increased signal to noise ratio, and ability to resolve velocity inversions. This paper presents a case study that explores the abilities of MASW as an unknown foundation characterization tool. MASW was applied to determine subsurface stiffness at a bridge foundation site in the Philadelphia metropolitan area. One MASW survey line was performed immediately over the foundation of interest and another was performed over a control zone adjacent to the foundation to establish a baseline site profile. The purpose of this testing was to examine whether MASW could establish the geometry of the foundation at this site. This paper presents the site conditions and MASW testing procedures, followed by a discussion of data analysis and interpretation.

Jan 1, 2016

By Robert G. Lenz

Control of ground water for construction purposes is an everyday occurrence in the U.S. Thousands of pumps are in service at any given time. Most of these applications simply consist of pumping water out of an excavation, generally with the aid of sumps. Modern hydraulic and electric submersible pumps permit these procedures because of their ability to pump solids and take air without losing their prime. These procedures work fine up to a point and permit the contractor to control his ground water problems adequately and at minimal cost. When that point is exceeded, the ground water problems sometimes are compounded. Over-application of open pumping techniques can result in slope failures, cofferdam instability, bottom heaving, boils, loss of ground, damage to adjacent structures and utilities, and assorted other maladys which could and should be avoided. This paper will deal with the options involved in ground water control, a discussion of the unwanted side effects of dewatering, and examples of ground water control projects in various cities around the U.S.

Jan 1, 1988

By Renzo D. Verastegui, T. C. Michael Law, Sitotaw Y. Fantaye, Alfredas Daugiala

"When completed, 520 Park Avenue will amend the Manhattan skyline and be one of the most prestigious high rise towers in New York City. The 52-story condominium building is located on a 60 by 100 feet lot on East 60th Street between Park and Madison Avenues. The geographically complex site is bounded by two fragile 5-story masonry buildings on the east and west, a mid-rise building on the north, and a New York City subway tunnel on the south. To add to this complexity, the ambitious development required 70 to 80 feet of excavation, mostly below groundwater level in highly permeable rock, to accommodate four levels of cellars. The new building also cantilevers 24 feet over a five-story historic building on the east. The limited footprint of the building coupled with large compressive and tensile axial loads, considerable base shear and over-turning moments, and the required deep excavation, presented unique foundation challenges. This paper describes how the challenges were solved with an innovative combination of permanent secant pile walls and drilled shafts.INTRODUCTIONThe project site is located at 45 East 60th Street, on the block bounded by East 61st Street to the north, East 60th Street to the south, Park Avenue to the east, and Madison Avenue to the west. As shown in Fig. 1, the site is surrounded on three sides by buildings sensitive to differential settlement. In addition, a NYCT underground subway structure lies below East 60th Street approximately 13 feet south of the site. The base of the subway structure is approximately 42 feet below the street.The project consisted of constructing a 52-story tall building. A portion of the superstructure cantilevers 24 feet over an adjacent five-story historic building. The underground construction for the new building involved a four-level basement, extending about 60 feet below ground surface. The excavation subgrade is much deeper than both the subway structure and the adjacent shallowly-founded building foundations."

Jan 1, 2016

By Tony Brunger, Abid O. Adekunte, George Munteanu, David Greentree

A number of novel solutions have been proposed in recent years as alternatives to props and tie-backs in deep excavation support e.g. Adekunte (2008), Deschamps et. al. (2008), Adekunte et al. (2010) and Adekunte (2014). A number of these non-standard restraining solutions involve the construction of permanent or temporary vertical or raking buttress piles that are rigidly connected to the excavation support wall at regular intervals along the wall run. This paper chiefly focuses on the design and construction of twin-vertical buttress piles as restraining systems behind or in front of embedded retaining walls. The system essentially relies on the push-pull mechanism that develops between the twin piles, to maintain the overall stability of the excavation support. The paper’s main areas of concentration include; finite element modelling, geostructural design, construction procedure, instrumentation and monitoring that are associated with the application of twin- buttress pile systems. These are supported with project details of three recently completed high-end luxurious residential developments in Greater London, England, on which the twin-buttress pile system was used to restrain the excavation support walls for the basements on the sites. The mode of application of the system varies across the three sites. While the system was adopted as a long term solution behind the retaining wall on one of the sites, it was designed and constructed for temporary use in front of the retaining walls on the other two sites. Instrumentation and monitoring results from all the sites show the non-traditional system to be safe and effective, whilst having significant beneficial effects on construction programme, sequence of works and project cost.

Jan 1, 2018

By David Siu

Many problems were encountered with the mechanical wedge-type splices used for the 15-inch square precast prestressed concrete piles installed at an industrial plant site. Many of the wedges were breaking during installation of the splices and after pile driving resumed following splicing. Dynamic monitoring of the piles and uplift loading tests confirmed that the problems were associated with cracked or damaged wedges. More ductile, annealed wedges were subsequently used, and, while not completely satisfactory, they were found to perform better than the original more brittle wedges. Introduction Long precast prestressed concrete piles were installed to support heavy, settlement-sensitive structures at an industrial plant in Port Alberni, British Columbia, Canada. The piles were driven through soft compressible silts and clays to toe bearing in a dense sand and gravel deposit or on bedrock. Each pile consisted of two or three segments joined with mechanical wedge-type splices trademarked DYN-A-SPLICE. Shortly after construction began, problems arose during pile installation, and these problems were, later, identified to be related to the wedges, or clamps, used to connect the splice plates.

Jan 1, 1991

By Alexi J. Neill

"This presentation will showcase two challenging projects with deep excavation support systems in the Atlanta area where state-of-the-art instrumentation and monitoring systems were used to manage risk by confirming design performance requirements / calculations during construction. The instrumentation and monitoring system successfully reduced risk by recording real-time data on a project website while simultaneously sending email alarms to key site personnel when data exceeded pre-determined alarm thresholds. The monitoring data revealed unexpected performance at an early enough stage so that contingency plans could be engaged and remedial efforts devised in order to limit the consequences. Finite element analysis was used to model deformations, analyze the unexpected performance, and prepare theremedial design.INTRODUCTIONConstruction in densely populated urban areas is becoming more common in order to keep up with the increasing infrastructure demands of our growing population. America’s big cities continue to outpace the overall nation in population growth. The city of Atlanta, the nation’s ninth largest city based on metropolitan population, is a prime example of this. The population has grown at a rate of 6.6% between 2010 and 2013, nearly triple the overall growth rate of the United States during the same period (SustainAtlanta, 2015).As a result of increasing infrastructure demands in Atlanta, developers are now constructing larger buildings on smaller properties. In addition, developers are attempting to maximize space on their selected properties, often by designing underground parking garages to accommodate as many cars as possible on these compact sites. In some cases the selected sites are adjacent to buildings, utilities, and other existing structures. The risk associated with construction increases during underground work that requires a support of excavation system, particularly on confined sites adjacent to existing structures. There is a risk posed to people, property, and the environment that the project team should monitor when constructing in these conditions."

Jan 1, 2016

By Seth L. Pearlman

Pin Piles are small diameter high capacity drilled and grouted piles also called minipiles or micropiles. They are ideal for building foundations on sites with poor ground conditions, sensitive surroundings, restricted vertical clearance, or difficult access. They are also well suited to foundation underpinning, arresting ground movements, and increasing the capacity of existing foundations. The major factors for selection of Pin Piles are reviewed; drilling, grouting, and design fundamentals are summarized; and a major case history is presented for the underpinning of the 43 story elevator core at the recently opened Mandalay Bay Resort and Casino in Las Vegas, NV.

Jan 1, 2000

By Mario Terceros H, Bengt H. Fellenius

"ABSTRACTThe city of Santa Cruz, Bolivia, is historically dominated by houses and three to five storey buildings.The geology in and around the city is such that even very light buildings need to be supported onpiles. The recent increase of the Bolivian economy, notably that of Santa Cruz, has created a demandfor new residential as well as office and industrial buildings, which mostly consist of multi-storey orhigh-rise buildings with significantly larger foundation loads. Foundation piles have become largerand longer, and the load on individual piles is increased. The development has resulted in an increasein the demand for more sophisticated design and construction methods and stricter approach toverifying the quality of the construction processes and results.This paper describes to geology of the Santa Cruz region and how the geotechnical conditions areconsidered in the design and construction of piled foundations. The improvement of past constructionand design techniques, based mostly on bored piles constructed with bentonite slurry, is beingreplaced with new methods of constructing bored piles, e.g. the Full Displacement Pile (FDP) andincorporation of techniques such as enlarging the pile toe, e.g., with the Expander Body. This paperpresents the results of several full-scale tests and discusses the incorporation of the test results indesign and construction.1 GEOLOGY OF THE REGIONSanta Cruz de la Sierra is located in the eastern lowlands and sub-Andean zone of Bolivia, SouthAmerica. The area lies at an elevation of about +400 m and the geology is a Paleozoic (250 millionyears old) sedimentary basin. The soils of interest to civil engineering construction are quaternarywith the dominant minerals being calcite, silica and feldspar. The main agent is the Piray River and itstributaries. Their past meandering over the area has resulted in a sedimentation-erosionsedimentationprocess and a profile dominated by fine to medium sands with intermittent layers ofclay or clayey sand. With increasing distance from the river, the clay-containing layers are thicker.Fig.1.- View of Bolivia with location of Santa Cruz and map of Santa CruzThe upper about 15 to 18 m thick part of the profile consists of normally consolidated layers of clays,silts, sands, in various combination and thickness. Below, the soil is more homogeneous and consistsmostly of sand and gravel. The groundwater table lies typically at a depth of about 6 m in the highestpart of the city and at about 1 to 3 m depth in the lowest part of the city."

Jan 1, 2014

By Song-yu Liu, Chao Yan, Yong-feng Deng

"In order to investigate the stability of embankment on soft subgrade improved by T-shaped deep mixed column composite foundation, the internal forces and failure modes of columns were analyzed on the shape of critical slip surface and the displacement fields of composite foundation through strength reduction method of three dimensional numerical simulation. Then comparison between T-shaped and conventional deep mixed column composite foundation were conducted. The simulation results indicate that the stability analysis was overestimated by limit equilibrium methods. Piles within the slope shoulder provide great resistance slide effect through the vertical bearing capacity, while the piles nearby slope shoulder and outside slope shoulder providing great moment to resistant slip. The embankment stability of T-shaped deep mixed column composite foundation is higher than that of conventional deep mixed column composite foundation while cost less cement and construction time.INTRODUCTIONThe soft soil has many unfavorable project properties such as high compressibility, low strength, and high water component. Embankment built on the soft soil will face subsidence, horizontal displacement and stability problems. Cement-soil deep mixed column composite foundation is more commonly used as a method for construction of embankment on soft ground [1-2]. For the existing problems of China's current cement-soil pile (wet jet mixing pile), including strength uneven, effective treatment with shallow depth and high cost, a new technique, T-shaped bidirectional deep mixed column, is introduced [3]. An automatic expanding mixing blade was developed by Liu et al. shown in Figure. 1, to install TDM columns [4].T-shaped deep mixed (TDM) column combines bi-directional deep mixing technique and T-shaped deep mixing technique: ?Using concentric biaxial drill pipe, opposite rotational direction of the blade on the inner drill pipe and the outer drill pipe. By squeezing action of the blade on the outer drill pipe, forward and reverse rotation of the blades bidirectional mixing at the same time, blocking the way to take the grout, the uniformity of cement mixing is improved. ?Scalable stirring blades, which can be stretched for two different radius at any depth below ground, expand cross-section of the upper pile (enlarged head), forming expanding cross-section within the upper part of a certain depth which is similar to the shape of nail. As a new composite foundation, T-shaped mixing pile composite foundation is widely applied. However, studies on the stability of T-shaped column treated soft subgrade are rare in the research. So the stability study on T-shaped column composite foundation under embankment for guiding the design and construction has important significance."

Jan 1, 2015

By Jerold Bishop, Grant Bearss, Aleksey Egorov

"When a shock wave is released in the bottom of a drill hole filled with wet concrete slurry, the result is called an electrohydrodynamic effect, or EHDE. The energy is carried through the fluid with minimal loss because the slurry is an incompressible medium. Repetitive discharges provide a series of energy pulses that compact the soil along the pile shaft and at its base. The process is analogous to repeated applications of low-energy blast densification or to dynamic compaction. In general, the process is not depth dependent. EHDE was identified in the 18th century by an American scientist who observed that a spark between two electrodes placed under water induced a burst of pressure. In 1957, two Russian engineers formulated a process and received a patent for a method of creating a pressure wave by transforming power from an electrical discharge to a mechanical impact. They derived more than 200 applications for technical and industrial processes.In the 1970s, civil engineers at the Engineering and Building Institute in St. Petersburg, Russia, began to look at EHDE to improve the capacity of drilled piles. Early experiments showed that electric discharges in a wet concrete slurry mix could create a pressure wave of up to 26 MPa (3700 psi). Later tests demonstrated that this pressure level could be created in a drilled pile hole. The researchers devised equipment and in the early 1990s began to study pulse technology as applied to drilled piles.This application was accepted into the Russian Federation Building Code in the 1990s. The code treats “regular” drilled piles with equivalent bearing area as having roughly half the capacity of a driven pile. However, the code considers drilled piles treated with the EHDE technique a direct “one for one” substitution for driven piles and allows higher values if the capacity is established by static load testing. Hundreds of projects have been completed in Russia using this technology to value engineer drilled pile projects. In several instances, the number of drilled piles installed was fewer than half of the number originally planned for due to the capacity increase that EHDE-treated piles provided.Drilled PilesIn drilled pile construction, the EHDE process creates a mechanical pressure wave that impacts the base and sidewall of a drilled pile shaft. Soft, poorly consolidated or loose soil is compacted by successive pulses of pressure created by electrical discharges. These mechanical impulses are made by inserting a discharge probe into the wet concrete slurry. A discharge across the tip of the probe creates the pulse that travels outward to the sidewall and base of the drilled pile through the incompressible medium of the slurry. The power pack ratings for equipment presently in use are 35 and 50 kJ (kilojoule).Each pressure wave strikes the soil, causing compaction and expanding the hole. Workers apply the pulses until the size of the hole stops increasing. They watch the slurry level during pulsing. When the level quits dropping, further soil compaction in the drill hole sidewalls and base is not possible. After the pulse process is complete, workers insert a rebar cage and the pile is finished.The process does not alter the soil mineralogy. The electrical discharge is internally grounded and does not arc to the sidewalls of the drill hole. Soil is not scorched or altered in any manner; it is only compacted by the pressure wave. This technique has been used in urban areas with no effect on electrical or electronic equipment."

Jan 1, 2009

By Felix Cheng

Extensions to the Convention Centre in Adelaide, South Australia consisted in part of construction over the existing railway system comprising nine rail lines and passenger platforms. Vibro-pile (Aust) won the design and construct tender with a solution comprising over 500 cast insitu concrete piles. The pile types were 500 to 900mm diameter non-displacement CFA piles and 400mm diameter displacement V-piles. The V-pile is a cast insitu screw pile developed by Vibropile (Aust) Pty Ltd. Both pile types were installed with minimal noise and vibration required for the project, while the displacement V-pile had the advantage over the CFA pile by developing the same pile capacity but with a smaller diameter and with minimal spoil. The latter was important in alleviating spoil removal problems near the railway tracks and disposal of potentially contaminated spoil. The results of dynamic compression load testing and static lateral load testing indicated that the performance of a 400 mm V-pile was equivalent to a 500 mm CFA for this site. The lateral load testing indicated that the surficial soils have a major influence on the load-deflection response, but despite the site containing up to 4 m of filled ground, the piles were found to carry the required lateral loads satisfactorily.

Jan 1, 2002

By O&apos, M. W. Neill

Mini-piles have been found to be a practical, technically correct remedial underpinning method. They can be constructed in limited access areas with very little disruption. Experience indicated that mini-piles installed using a down-the-hole soil displacement hammer would be particularly effective in the "bottomless" Beaumont Clay formations in the Houston, Texas, U.S.A. area. The University of Houston Foundation Testing Facility was ideally suited to perform tests on mini-piles. The availability of extensive geotechnical data and previous pile test results was invaluable in evaluating the mini-pile test data. As expected, the mini-pile test results were consistant with test results from large sized driven piles in the same soil formation.

Jan 1, 1989

By Ross Cutts

As a public servant geotechnical engineer, I observed how costly and valuable geotechnical field explorations are to the success of every project. Often however, the field exploration is a long and complex process that is made less efficient by the difficulty of retrieving and utilizing nearby internal or external historic geotechnical datasets. As an employee of a public agency, we would often start our investigations for every project from scratch, given the difficulty of locating and utilizing historic geotechnical data. This is an ethical and technical failing of our profession. When we start subsurface explorations from scratch, not only do we often duplicate investigations, we are also likely defaulting to reapplying tradi- tional test methods that yield con- servative geotechnical parameters, resulting in overly conservative and potentially costly construction. To address this issue while working as a public servant, I started a research program with Yunfeng Zhang, Ph.D., of the University of Maryland, to build a tool that could compile internal historic geotechnical data and extract additional value from it, using machine learning. This tool was able to provide, upon request, nearby historic geotechnical data, estimated soil parameters and recommendations for geotechnical test methods best suited for a given project site. This prevented common field ex- ploration problems such as, requesting duplicate data, requesting test methods that were not applicable for the project geology, not realizing presence of karsts, missing permits for wetlands, private property and others. This tool allowed for more efficient field investigations with regards to time and money saved. There was one problem with this tool: it could only be used by internal employees of a single state's depart- ment of transportation (DOT) for which this data was compiled. I realized at that point that it would be of tremendous value to make this concept universally accessible to the geotechnical engi- neering profession. I left public service to devote time to building a platform that would host historic geotechnical data from publicly funded sources throughout the country. The tool I helped build as a public servant was the foundation of Geosetta, a nonprofit company dedicated to serving the geotechnical profession. The nonprofit structure was adopted to prevent acquisition by a for-profit company and to ensure that Geosetta remains an independent steward of our profession's valuable data. Geosetta provides a GIS (geographic information system) platform that enables users to view historic geo- technical data and extract value from it with machine learning-based predictions and visualization tools. This data is provided in an open and interchangeable format called DIGGS, which stands for Data Interchange for Geotechnical and Geoenvironmental Specialists, making it easy for users to integrate it into their workflows. Geosetta is collaborating with the American Society of Civil Engineers' Geo-Institute and other sponsors to extract public data at no cost to the agency and provide the profession with free access to the existing data and access to advanced tools through a subscription to support the nonprofit mission.

Nov 1, 2023

By T. Wulleman, M. Ansriou

Integrity testing is a primary quality control check on a product that is for the most part not accessible to visual examination. Their cost can be expensive when using direct methods of inspection (like coring a pile) or more economical when using indirect methods (e.g. acoustic testing). All indirect methods operate by “inference” which means that they do not directly measure the defect of integrity. Indirect methods measure the variation of physical values (temperature, impedance, speed, ect.) correlated to the integrity of the pile allowing the detection of integrity defects, although these methods do not allow for the characterization of the defect. 1. INTRODUCTION Cast-in-place piles are particularly prone to integrity defects. The reasons for this are multiple, including lack of high quality of contractor workmanship, experience and supervision necessary in construction, variable soil and groundwater conditions on site, etc. Furthermore, visual inspection of the finalized pile is usually impossible. Therefore, special care has to be taken both during the execution process and during the subsequent quality control campaign to detect any defects of executed piles. Today, a lot of methods do exist to assess pile integrity. It is thus essential to understand the mechanism governing those devices to both make an engineering choice of the pile integrity testing method and to interpret correctly the provided results. 2. QUALITY IN PILE FOUNDATIONS 2.1 Pile anomalies A pile having an anomaly is a pile which has a different behavior from what is normally expected. The presence of a pile anomaly does not necessarily imply that a pile cannot be used for its intended purpose (Gordon & Chapman 2004). An anomaly can be considered as a defect, or a “performance” depending on the ability of the pile to fulfil the following three criteria (3C): C1 - Meet the Service Limit State (SLS) requirement and support the proposed working load without settling more than admissible by the superstructure ; C2 - Meet the Ultimate Limit State (ULS) requirement and carry a specified load with an adequate factor of safety against failure ; C3 - Remain durable throughout the design life of the structure such that the pile is not affected by time dependent activities (chemical attack, corrosion of steel reinforcement, ect.), which would jeopardize its ability to maintain its compliance with the first two criteria.

Jan 1, 2019

By David S. Graham, Joseph D. Bailey, Paul J. Axtell, Michael K. Muchard

"Two instrumented test piles were simultaneously subjected to a static lateral load test by jacking the piles apart. One of the piles was loaded in axial compression via kentledge during the lateral load test. Both piles were constructed in an identical manner. These piles were constructed and tested as part of a construction-phase load test program for a floodwall improvement project along the Missouri River in Kansas City, Kansas. Details of the subsurface conditions, drilled pile construction, instrumentation, and load testing procedures are described. Data collected during testing of the piles are presented and compared. Potential effects of the axial compressive load related to observed differences in pile lateral response are discussed.INTRODUCTIONTwo instrumented test piles were simultaneously subjected to a static lateral load with one of the piles also subject to a combined axial load during testing. The load test program was part of a floodwall improvement project in Kansas City, Kansas. Known as the BPU floodwall, the floodwall runs along the south bank of the Missouri River at a Kansas City Board of Public Utilities power generation and water treatment facility. The project location is shown in Fig. 1.Drilled, 2-ft (610-mm) diameter piles were designated by the designer, the U.S. Army Corps of Engineers (COE), as the foundation type for supporting extended floodwall footings. The drilled piles are fully cased, cast-in-place concrete, reinforced with a steel 12x74 (310x110) H-pile. In order to test soil lateral response and pile structural response under combined loading, the COE required that both a lateral test and combined lateral and axial test pile be constructed and tested. In order to most efficiently test both piles and to allow for simpler comparison, the two piles were simultaneously laterally loaded by jacking the piles apart, applying a maximum lateral load of 195 kips (867 kN). A constant axial load was applied to the combined test pile by kentledge prior to lateral loading and was maintained for the duration of the lateral load test. The total weight of the kentledge was 61.5 kips (274 kN). Fig. 2 shows the test setup."

Jan 1, 2017

By Robert Bittner

The following is a report on the development of two unique and separate cofferdam systems used in the construction of the marine foundations for the I-205 Columbia River Bridge at Portland, Oregon for the Oregon Department of Transportation. The first of these two systems utilized interlocking H-pile 100 ft long to form a cofferdam 145 ft by 58 ft in plan and 100 ft deep. The second system consisted of two immense bell shaped steel forms. The larger of the two forms was 83 ft by 66 ft in plan, 62 ft high and weighed 450 tons. This form was externally stiffened for a designed hydrostatic head of 54 ft. Both forms were designed, except for the top 14 ft, to be set and stripped in one solidly welded unit. The supporting geological formation for the bridge foundations is the Troutdale, a cemented sand and gravel. This formation is at the ground surface on the Washington Shore and slopes downward to a depth of 115 ft below normal high water at about mid-channel. In this area the Troutdale formation is covered with a layer of fine to medium sand 90 to 100 ft thick. It was the variable depth of the Troutdale which determined the two types of foundations and the corresponding to the two cofferdam systems.

Jan 1, 2013