Search Documents

By Madan Kumar Annam, Hari Krishna Y, I. V. Anirudhan

"For completion of projects in time with positive results, improvements of productivity and effective project management procedures have become extremely important. This paper discusses a milestone project comprising 198 residential units of stilt plus 4 levels that highlighted the benefits of these key aspects. Success of ground modification procedure benefitting the entire cycle involving End Users, Suppliers, Bankers and Developer is discussed.Soil profile for a considerable depth comprises weak layers of silty clay and sandy clay with varying consistency. Deep foundations have been an automatic choice of foundation for major buildings constructed in similar environment. After serious geotechnical appraisal, reconsideration of the foundation system with an alternative solution of Ground Improvement was found to be optimal in terms of Cost and Time. Full raft foundation on the improved ground by installation of Vibro Stone Columns (dry bottom feed method) was considered as an alternative foundation system. The ground improvement works were completed within 6 weeks (as against 6 months to that of pile foundations) that was made possible through effective project management. Full size plate load tests were conducted to ascertain effectiveness of the ground improvement works. Success of the foundation system was proved by full scale monitoring of foundation settlement during and after completion of the project over a span of 2 years. This paper describes design considerations, quality control in the construction of Vibro Stone Columns (dry bottom feed method) and performance monitoring of the project thereafter.INTRODUCTIONGenerally in weak deposits, deep foundations like bored cast-in-situ piles and driven piles have historically been the foundation choice for major buildings and other structures. Construction of pile foundations is becoming a challenge due to their high cost, large construction time and due to severe environmental issues (noise pollution, ground vibrations and carbon footprint). Since the proposed building complex is located within the proximity of a well-developed residential locality, objections raised by neighborhoods to pile driving activities called for a rethinking on the foundation system.The top 6m to 8m of soil profile comprises of silty clay / sandy clay having highly varying consistency. GWT was encountered at 3.0m below the existing ground level. Under this situation, the reconsideration of the type of foundation system with respect to the geotechnical analysis gave a thought to assess feasibility of ground improvement system."

Jan 1, 2015

By Scott White, Pishun Tantivangphaisal, Andrew Bell, Chris Barker

There has been considerable advancement in recent years in the tools, both software and hardware, available to allow efficient digitalization of site records during the construction of geotechnical works. Whilst these tools have excelled at replacing handwritten records, the ability to use digital records to validate design and construction requirements in real time or even within reasonable timescales has generally been limited to the development of bespoke ‘prototype’ project specific solutions. This paper describes the development and implementation of an industry standard design schedule and the benefits of the broad adoption of a single database schema for data recorded on geotechnical sites. The former has brought significant improvements and automation of the design process, whilst the latter has enabled the validation of the constructed works against design intent in almost real time. Further details of the standardized design schedule, already publicly available in the UK through the FPS, examples and lessons learnt from implementing digital site record systems on live projects are presented herein. The utilization of cloud computing technology and complex algorithms linking plant/rig instrumentation with design data can further automate construction sites using IoT (Internet of Things) best practices. The authors will share their experience of the recent deployment of a digitalized design-to-construction record system, give recommendations for future development and a call for an industry wide drive to finalize and adopt the AGS Piling data schema.

May 1, 2022

By John S. Pack

The last 25 years have seen rapid expansion in the use of helical screw pile foundations and tiebacks for new and retrofit construction of buildings and earth retention structures. An estimated $100 million was spent in 2002 on helical foundations and tiebacks in the United States alone. While design information is available in the literature, information regarding quality control, inspection and performance monitoring is lacking. Recognition of at least one manufacturer's helical foundation material by the Uniform Building Code, Standard Building Code, and BOCA (all three codes now combined into the ICC International Building Code) has given added urgency to the dissemination of reliable and practical quality control, inspection and performance monitoring procedures. This paper describes a set of such procedures that have been followed for 17 years by engineers experienced in the industry who have directly installed or been involved in the installation of over 140,000 helical foundations and tiebacks in divers soil conditions for various types of structures, including earth retention structures. Topics covered include design responsibility, building code listings and requirements, manufacturer ISO certification, manufacturing process, material and installation specifications, installation contractor certification, field placement, installation procedures, field inspection, building code inspection and performance monitoring. The paper concludes with a step by step example of practical quality control, inspection and performance monitoring procedures on a typical helical foundation project.

Jan 1, 2003

By Jørn Thomsen, Christoffer Brodbaek

"As governments increasingly accord high priority to sustainable energy, policymakers are finding that wind energy has a long track record as a proven alternative to conventional energy supply.Over the past two decades, wind turbine projects have been constructed offshore because of more stable offshore wind conditions and because there is more available space for large wind farms out in the open sea. Vindeby Wind Farm in southern Denmark was constructed in 1991. As the world’s first offshore wind farm, it provided valuable information and experience for researchers and designers that have led to new technologies and design improvements, a trend that will continue as more offshore wind farms are constructed. Today, the world’s capacity of the installed offshore wind turbines exceeds 1,000 MW. Most of these are installed in Northern Europe where there was early political support and favorable conditions, such as strong winds and relatively shallow waters. Offshore wind projects are now under development around the globe, including continental Europe, the U.K. and North America. ‘The largest offshore wind farm today is Denmark’s Nysted Offshore Wind Farm, which has a total capacity of approximately 480,000 MWh, equivalent to the yearly consumption of 120,000 households. It is five to six miles offshore in the Baltic Sea in the southern part of Denmark.The owner is a joint venture between DONG Energy of Denmark and E.ON Sweden. Bonus Energy (now Siemens) supplied the wind turbines, and P. Aarsleff A/S and subcontractors supplied the foundations. The contractor’s consultant, COWI A/S of Denmark, developed and designed the turbine foundations. With a total capacity of 165.6 MW, the project consists of 72 Bonus 2.3 MW turbines in water depths up to 33 ft. The turbines have a hub height of 226 ft, and the turbine blade diameter is 270 ft. The rotor and nacelle (the structure that houses the generator, gearbox and other equipment) weigh approximately 150 tons, and the weight of the steel tower is approximately 130 tons. The wind farm site is located in a relatively protected area of the Baltic Sea, but during the winter months, the water often freezes and the foundations needed to be constructed to resist ice forces. The founding soils at the site are overconsolidated clay tills with boulders and with a thin layer of softer surface sediments. Pockets of up to 30 ft of soft sediments were encountered, which required special foundation preparations."

Jan 1, 2009

By Amy B. Cerato

The application of this study is to use helical anchors as a foundation system for small wind tower (1 ? 10 kW) guyed cables. Helical anchors are currently used to anchor guyed cables of telecommunication and electric towers. However, the increased dynamic vibrations a wind turbine adds to the tower and foundation system under working loads, as well as extreme environmental conditions (e.g., straight line winds, ice load or sudden furling shocks), require additional knowledge about the behavior of helical anchors. These field conditions were simulated in this study by instrumenting a working tower with load cells and 3-axis accelerometers to gather data on wind speed and tower response. These tower responses were then transmitted to the helical anchors through an extensive, large-scale testing program that included monitoring the performance of the helical anchor foundation under dynamic loads, subject to natural variations in both wind regimes, precipitation (water level) and variations in helical anchor geometry. This paper specifically discusses the effects of helical anchor geometry on helical anchor performance under long-term dynamic loads.

Jan 1, 2008

By Peter Middendorp, Gerald E. H. Verbeek

"This paper will describe a brief history of the method of characteristics as an accurate solution of the wave equation, and the author's experiences with the method of characteristics over a period of 30 years.As a result of the offshore pile driving activities associated with the development of the North Sea oil fields in the 1970's, two Dutch companies initiated extensive research efforts. Heerema started to research the dynamic behavior of soil during driving and HBG (Hollandsche Seton Groep) extended the method of characteristics with a straightforward theoretical solution for the shaft friction along a pile.The research institute TNO started the development of the wave equation program TNOWAVE in the late 1970's based on HBG's friction model extension for the method of characteristics. Today the program has a worldwide application in the field of pile testing. This paper will describe its development and application over time and its relation to today's applications for driveability studies for impact hammers (PDPWAVE) and vibratory hammers (VDPWAVE), signal matching for Dynamic Load Testing (DL TWAVE), Pile Integrity Testing signal matching (SITWAVE), and Statnamic simulation (STNWAVE).The paper will highlight that these developments have been the result of multi-disciplinary and multi-national efforts and encourage geotechnical engineers to seek further developments of the wave equation program in a similar manner. Finally, the paper will indicate some areas where such further developments are required."

Jan 1, 2005

By Michael W. Driller, Wen Yan (Grace) Chen, Steven J. Friesen

"Remediation for Perris Dam has been proposed in response to deficiencies identified in a seismic stability study prepared by the California Department of Water Resources (DWR) in 2005. Lenses of potentially liquefiable soil have been identified within the dam foundation which may lose strength during a seismic event. The remediation was designed primarily to limit deformation of the dam. Nineteen construction methods were compared and evaluated for the remediation. The final decision was to use cement deep soil mixing (CDSM) to strengthen the foundation and to construct a downstream berm to stabilize the dam. The entire CDSM treatment will cover over 4,000 linear feet of the downstream toe of the dam. Over 300,000 cubic yards of CDSM will be used to strengthen the foundation. The construction of the project started in Fall 2014 and is anticipated to take approximately 3 years. This paper describes the design aspects of using CDSM to treat the foundation, including laboratory testing, investigation of overstressing/cracking, extent of treatment, effect of CDSM on pore pressures under the dam, and the results of a full-scale CDSM test section.INTRODUCTIONPerris Dam is a zoned earthfill dam with a length of 2.2 miles, a maximum height of 128 feet, and a capacity of 131,450 acre-ft of water. The dam is located in Riverside County, California at the terminus of the East Branch of the State Water Project. The embankment was constructed between 1971 and 1973 over an alluvial deposit between the Bernasconi Hills to the South and Russell Mountains to the North. A rock outcrop divides the dam into left and right reaches when viewed from the reservoir looking downstream. The embankment soil was obtained from a borrow source at the North end of the reservoir. The dam has a sloping sandy clay core (Zone 1) with a 10-foot deep cutoff trench and a silty sand shell (Zone 2) with a downstream chimney and blanket drain (Zone 3 and Zone 4) as shown in Figure 1."

Jan 1, 2015

By Abu B. Siddique, Anthony S. Crincoli

"The New Jersey Turnpike Section 2 widening program consisted of widening between Interchange 6 in Mansfield Township, Burlington County and Interchange 9 in East Brunswick Township, Middlesex County. To accommodate large volume of traffic the roadway was widened from 6 to 12 lanes with major modifications performed at four interchanges. The Section 2, NJTA Interchange 6 to 9 Widening Program is a 4.2-mile section of Turnpike roadway which included a total of 12 new or modified structures. In order to facilitate the construction process Section 2 was divided into three construction contract packages. This paper will cover the last and final Contract T869.120.203 which is 1.7 miles in length. The work generally consisted of eight new ramps connection to and from the toll plaza to the new inner and outer roadways. New mainline bridges were constructed over several ramps. A new bridge was constructed to take northbound outer lanes traffic over two ramps along with new mainline bridges over Black’s Creek, Georgetown Road, and Laurel Run. In addition, a new bridge was constructed to take a ramp over Laurel Run and the existing U-turn Bridge was replaced with a new one.For Contract T869.120.203 a total of 74 five-foot diameter drilled shafts has been constructed to support all pier foundations for bridges. Three drilled shafts were tested using Osterberg Load Cells to verify the estimated shaft resistance during design phase. One Osterberg Load Cell test was performed on a demonstration (sacrificial) shaft and the other two Osterberg Load Cell tests were performed on production shafts. This paper compares the estimated total, side and tip resistances with corresponding measured total, side and tip resistances and provided recommendations for future design purpose.INTRODUCTIONTo accommodate large volume of traffic the New Jersey Turnpike Authority (NJTA) decided to widen Section 2, which included Interchange 6 through Interchange 9. The Section 2, a 4.2-mile section of Turnpike roadway that was widened from 6 to 12 lanes with major modifications performed at four interchanges.The New Jersey Turnpike Authority (NJTA) procured AECOM to perform engineering services for the final design of Section 2, NJTA Interchange 6 to 9 Widening Program. Section 2 is a 4.2-mile section of Turnpike roadway that will widen from 6 to 12 lanes and will include a total of 12 new or modified structures. It encompasses modifications of the existing and the design of four new ramps at Interchange 7. The project also includes the modification of two local roads over the mainline, two local roads under the mainline, two maintenance U-turns, and retaining walls. In addition, the project consists of the design of noise walls, sign structures, storm water management basins and the more typical drainage, utilities, lighting, roadway, ROW, and signing and striping design."

Jan 1, 2015

By Chu E. Ho, Paul Napoli

This paper presents the performance of nineteen open-ended steel pipe piles driven through highly variable overburden soils into glacial till and schist bedrock. The piles were 16 inches in diameter and 0.656 inches thick, with yield strength of 50 ksi. The piles were designed for a service capacity of 250 kips and were driven to achieve an ultimate geotechnical capacity of at least 500 kips. Due to the large variation in the ground conditions, installed pile lengths ranged from 25 to 66 feet. Some piles were driven to refusal on the bedrock while others were terminated at final driving resistance of 2 to 7 blows/in. Two piles were suspected to be plugged during driving while others did not. Each pile was instrumented with strain gages and accelerometers near the pile top, and observed using a Pile Driving Analyzer (PDA) to provide preliminary guidance on pile capacity achieved at end of initial drive (EOID). The influence of plugged and unplugged pile toe conditions on the interpretation of pile capacity was investigated using Case Pile Wave Analysis Program (CAPWAP). Characteristics of driving energy, compressive and tensile stresses developed in the steel pipe piles, and the resulting pile deformation behavior are discussed. INTRODUCTION The Hunters Point South redevelopment in Long Island City, Queens is one of New York City’s major efforts to transform former manufacturing zones into mixed developments for the middle-income community. The site is located along the eastern shoreline of the East River and Newtown Creek. The development included low to high-rise residential buildings, a public school and retail structures. Open spaces were created along the East River and Newtown Creek waterfronts in the form of a continuous park providing for recreational and community related activities. Waterfront structures included small park buildings, walkways and viewing platforms with the shoreline protected by revetments as part of the City’s flood mitigation strategy. The project was implemented in two phases, with completion of construction for Phase 1 in 2013 and Phase 2 in 2019. Based on available historical information, extensive reclamation took place between 1855 and 1898. After 1951, changes to the shoreline were made along the East River, including the removal of reclaimed land along the northern portion of the project site to allow for docking facilities. By 1977, these facilities had been demolished and backfilled to form the current shoreline configuration. The present site was temporarily used as a parking lot with stockpiles of fill mixed with construction demolition rubble, rip-rap and boulders of varying heights across the site. The existing ground surface varied significantly up to approximately 25 feet difference in elevation. The stockpiles were removed and the site was re-graded during final development of the project. This paper discusses the foundation design challenges due to the loose overburden soils and potential obstructions within the fill material, in particular, the issues relating to installation of open-ended steel pipe piles through the ground conditions encountered on site.

Jan 1, 2019

By Piotr Kozlowski, Stanley L. Worst, Matthew J. Niermann

The Waterman Hospital in Tavares, Florida was undergoing an expansion and required a below-grade excavation immediately adjacent to the Emergency Department. This wing of the hospital was under high traffic and required uninterrupted access for ambulances as well as helicopter landings. The below-grade expansion was also next to a part of the hospital which did not have a basement. Tiedback soldier beams and wood lagging were used as the earth retention system where the shoring line was not immediately adjacent to the existing structure. Structural jet grout underpinning was used to support the existing building and to serve as the earth retention system in the more sensitive area. Jet grout underpinning was chosen to minimize movements, loss of ground and settlement of the structure which was bearing on clean sand deposits. This paper will discuss the design, quality control and construction of jet grouting and its application to this project. INTRODUCTION Project Background The expansion of the Waterman Hospital included an addition to the Emergency Department. This addition was located adjacent to the existing hospital building in a congested area with limited access. The north side of the addition was bordered by the ambulance drop-off area. The south side of the addition was bordered by the helipad landing area. Both areas had to remain open and fully accessible 24 hours a day, 7 days a week.

Jan 1, 2019

By Remco Offenberg, Marcel Bielefeld, Martijn van Delft

The question of the continued suitability of existing foundations arises when the function of the superstructure changes. This can occur when the superstructure is replaced or when the existing structure is expanded, leading to higher loads on the existing foundation. Quite often it is a challenge to define the suitability (with respect to integrity, bearing capacity or both). The lack of information on the existing foundation (such as pile dimensions, installation records, original soil investigation, design calculations, etc.) makes it frequently seemingly impossible to assess whether the foundation or foundation elements can be re-used. The paper outlines the tools available to an engineer to evaluate existing foundation piles for potential re-use. The paper illustrates the application of these tools through a few case studies from The Netherlands, including the evaluation of a 400 years old bridge foundation to address increasing traffic loads.

May 1, 2022

By Gerald Verbeek, Erick Baziw

Downhole Seismic Testing (DST) is an extensively utilized geotechnical tool for site characterization. DST provides low strain (<10-5) in-situ interval shear and compression wave velocity estimates. These velocities are determined by obtaining relative arrival times of source waves as they travel through the stratigraphy and are recorded by one or more vertically offset seismic sensors. The DST arrival times have associated measurements errors and resolution limitations, which become more pronounced as the depth interval of analysis is reduced. Baziw Consulting Engineers (BCE) has developed a new DST analysis technique, the so-called DSTPolyKF algorithm, whereby the arrival times of DST data set are used to define a high order polynomial. The main advantages of this new technique are four-fold: 1) the ability to utilize all arrival time estimates irrespective of measurement errors. 2) the ability to analyze the data with user specified and even small (≤ 0.5m) depth intervals. 3) the ability to apply sophisticated data fusion for significantly more accurate DST interval velocity estimation. 4) the use of polynomial regression accuracy parameters to quantify how well the “best fit” polynomial fits the acquired arrival time data sets. This paper outlines the mathematical details of the best fit polynomial where a Kalman filter formulation is implemented. The performance of the DSTPolyKF algorithm is demonstrated by processing real DST data sets.

Oct 1, 2022

By M. England

A method for the analysis and prediction of single pile displacement behaviour is described. It is the displacement in time, under constant load, based on the use of hyperbolic functions to characterise individual constituents of the displacement-time behaviour. Extensive use of this technique has confirmed its validity in a variety of soils and that consolidation and creep settlement appear to be indistinguishable. The algorithms employed are suitable to model the displacement behaviour from the onset of load to infinite time for all types of piles and surface foundations. Until the advent of computer controlled static load testing, analysis of the displacement-time characteristic during pile load tests has been hindered by the quality of the data recorded and inconsistency of loading. This has hitherto made the development of suitable behavioural models very difficult. Understanding the soil deformation within a proper time framework allows the subject of pile instrumentation and testing to be developed. The equipment required is basically a computer controlled loading and pile head displacement measuring system which allows accurate analysis of the settlement characteristic in almost every situation.

Jan 1, 1993

By Matthias Pulsfort, Hanna Nissen, Markus Herten

An insufficient integrity of cast in-situ bored piles can lead to a reduction of the load bearing capacity and may require cost intensive repairs. Reasons for an insufficient pile integrity are linked to the construction process, mainly to poor concrete quality leading to bleeding and segregation of the fresh concrete. Moreover, the entrapment of soil and an insufficient concrete cover can pose a problem. Knowledge about the time-dependent development of the fresh concrete pressure during the construction process of bored piles is needed for a better understanding of the underlying processes causing these defects. Therefore, pressure measurements were carried out on different construction sites with pressure cells being installed at different depths along the reinforcement cage. The measurements revealed the maximum pressure acting on the surrounding soil. The achievement is a better understanding of the effects of the concrete placement specifically and the construction process in general on the surrounding soil to reduce the risk of pile imperfections.

Sep 8, 2021

By R. B. King

This document was prepared by the DFI International Grouting Committee with the intent to provide a summary of main Standards and Guidelines available for the North America and Europe grouting industry. This document highlights the different approaches, methods and tools used internationally. The DFI International Grouting Committee comprises all parties involved on a grouting project: Owners, regulators, engineers, contractors, and manufacturers (equipment and materials). This document is not intended to cover every conceivable application or requirement of grouting. However, it does provide standard practice requirements for qualifications, materials, equipment, testing, and production procedures for the professional engineer to incorporate into their project specific requirements.

Jan 1, 2021

By Rouzbeh Vakili, Adel M. Hanna

"The application of piled raft foundations has significantly increased during the last few years. In this system, the raft and the pile group collectively transfer the applied building load to the underlying soil layers. Determination of load sharing between the raft and the piles derives the complexity of piled raft designs due to its multi-parameter nature. These parameters are but not limited to: soil density, pile length, pile spacing, raft geometry, and piles installation technique. This study is to examine experimentally the effect of sand density and pile installation techniques on the load sharing mechanism. Experimentally, tests were conducted on a square rigid raft with a single pile in sand under three different soil densities; 30%, 45%, and 60%. The experimental results are used to determine the pile and the raft shares in non-displacement and displacement piled raft systems. The results of this study reveal that soil density changes the load sharing of displacement piled raft; the pile share increases in higher soil density. However, this is not the case in non-displacement piled raft and load sharing is independent of soil density in working loads.IntroductionThe piled raft foundation is a combination of shallow and deep foundation which transfers the superstructure load to the soil by a complex soilstructure interaction. The interacting mechanism among foundation elements and their surrounding soil is illustrated schematically in Figure 1 and could be classified into two categories: (1) pile-soil-pile and (2) pile-soil-raft. The pile-soil-pile interaction is the same as the free standing pile group and is a function of pile spacing and pile installation method. Pile-soil-raft interaction, which only involves in piled raft foundation design, could be affected by: the length, spacing, and roughness of the pile, the rigidity and dimension of the cap, soil condition, and the pile installation method. Pile-soil-raft interaction could have favourable and unfavourable effects on bearing capacity and settlement, respectively. The pressure between the cap and the soil favourably increases the horizontal stress on the pile shaft and consequently increase the shaft resistance. Whereas, this pressure induces negative skin friction on the piles which increases the settlement. The pile-soil-raft interaction mainly controls the load sharing mechanism of piled raft foundation when pile spacing (S) is more than 3.5dp."

Jan 1, 2017

By Craig H. Olson

"A new ship dock at a Philadelphia area refinery will be capable of docking the largest tanker to travel the Delaware River, the Stena V-MAX, which will induce significant lateral loads. The loads at the dock, a system of mooring dolphins and platforms, will be resisted by over 150 pipe piles, including some 20- and 30-in diameter, reinforced, concrete-filled pipe piles and H-piles. Construction included driving the pipe piles to the required ultimate capacity, flushing the pipe pile casing clean of overburden materials, followed by drilling rock sockets into the underlying Wissahickon Formation. The Wissahickon Formation is a complex subsurface that includes variations in depth to bedrock, rock quality, degree of weathering and the presence of very hard quartzite lenses or inclusions. Because of the problematic subsurface, the designers and client requested extensive pile dynamic analysis (PDA) testing by TRC Engineers (TRC).Before beginning, the contractor requested that TRC perform the WEAP (wave equation analysis program) to evaluate the proposed hammer (APE D30-32 open-end diesel) to drive the piles into the proposed bearing strata while maintaining allowable compression stress levels. The WEAP provided a prediction of blow counts and stresses for various ultimate capacities, and showed that for the HP14x89 piles with a required ultimate capacity of 480 kips, a blow count of at least four blows per in at a stroke of 8.0 ft was necessary.New Approachway RampThe PDA testing began at the new dock approachway ramp, parallel to the existing one. The new structure is a 300-ft-long by 21- ft-wide concrete deck supported on seven bents; each has two 24- ft-diameter steel open-ended pipe piles. Every pipe received an HP 14 x 89 x 80-ft pile that was later driven beyond the pipe pile tip to create a composite pile. The pipe piles were later cleaned of overburden materials and finally filled with concrete and rebar. At each bent, a cap was installed on top of each pair of pipe piles, and then a prefabricated concrete deck was added."

Jan 1, 2008

By Craig H. Olson

"Anew ship dock at a Philadelphia area refinery will be capable of docking the largest tanker to travel the Delaware River, the Stena V-MAX, which will induce significant lateral loads. The loads at the dock, a system of mooring dolphins and platforms, will be resisted by over 150 pipe piles, including some 20- and 30-in diameter, reinforced, concrete-filled pipe piles and H-piles. Construction included driving the pipe piles to the required ultimate capacity, flushing the pipe pile casing clean of overburden materials, followed by drilling rock sockets into the underlying Wissahickon Formation. The Wissahickon Formation is a complex subsurface that includes variations in depth to bedrock, rock quality, degree of weathering and the presence of very hard quartzite lenses or inclusions. Because of the problematic subsurface, the designers and client requested extensive pile dynamic analysis (PDA) testing by TRC Engineers (TRC).Before beginning, the contractor requested that TRC perform the WEAP (wave equation analysis program) to evaluate the proposed hammer (APE D30-32 open-end diesel) to drive the piles into the proposed bearing strata while maintaining allowable compression stress levels. The WEAP provided a prediction of blow counts and stresses for various ultimate capacities, and showed that for the HP14x89 piles with a required ultimate capacity of 480 kips, a blow count of at least four blows per in at a stroke of 8.0 ft was necessary. New Approachway RampThe PDA testing began at the new dock approach way ramp, parallel to the existing one. The new structure is a 300-ft-long by 21- ft-wide concrete deck supported on seven bents; each has two 24- ft-diameter steel open-ended pipe piles. Every pipe received an HP 14 x 89 x 80-ft pile that was later driven beyond the pipe pile tip to create a composite pile. The pipe piles were later cleaned of overburden materials and finally filled with concrete and rebar. At each bent, a cap was installed on top of each pair of pipe piles, and then a prefabricated concrete deck was added."

Jan 1, 2008

By Marco Fellin, Van E. Komurka

Significant cost and construction benefits were obtained from performing a bi-directional static load test prior to construction on the Russell Street Bridge Replacement project in Missoula, Montana. The project utilized 24 drilled shafts to support two three-span bridges across the Clark Fork River. A bi-directional static load test (“BDSLT”) was performed on a large-diameter production shaft to demonstrate construction methods and confirm design assumptions. Subsurface conditions consisted of gravel with sand to a depth of 20 feet (6.1 m), underlain by gravel with sand, silt, cobbles, and occasional boulders. The test shaft had a nominal diameter of 5.9 feet (1.8 m), and an embedded length of 75.5 feet (23.0 m). The geotechnical engineer of record and the BDSLT test engineer collaborated to optimize the BDSLT jack assembly location within the test shaft, determine appropriate instrumentation locations, and plan the test protocol. The maximum applied test load was 10,707 kips (47.6 kN). Significant benefits were obtained from performing the BDSLT test, including 1) reducing each production shaft’s length by using a higher LRFD resistance factor allowed by having performed the testing, 2) using test-determined unit shaft resistances to evaluate and accept two production shafts that may have otherwise required remediation, and 3) providing the Montana Department of Transportation (and other designers) with increased presumptive unit resistance values in the gravel/cobble/boulder deposits. PROJECT DESCRIPTION The project was constructed in Missoula, Montana for the Montana Department of Transportation (“MDT”). The original bridge was approximately 60 years old, and consisted of a two-lane, 420-foot-long (128-m), four-span, riveted steel plate girder design spanning the Clark Fork River. The bridge was due for replacement owing to its deteriorated state, and the need for increased traffic volume capability afforded by a four-lane structure. HDR was the structural engineer. The preferred bridge alternate was a 459-foot- long (140-m), three-span, welded steel plate girder design. The new bridge was designed to meet current standards in accordance with MDT bridge design and AASHTO LRFD criteria. The new bridge was constructed in phases to keep traffic open during construction.

Jan 1, 2019

By Jorj O. Osterberg

The Osterberg (O-Cell) Method makes it possible to separate the side shear resistance (skin friction) from end bearing. The O-Cell is placed on or near the bottom of a drilled shaft and after the concrete is poured and cured, an equal upward and downward pressure is applied. From the test, the load-upward deflection curve in side shear and the load-downward deflection curve in end bearing are drawn. Typical curves are shown where the ultimate load in side-shear is reached and where the ultimate load in end bearing is reached. Several examples of tests in which the test load reached ultimate loads far in excess of what was expected are shown. The side shear in rock sockets is shown to be much larger than generally estimated. Examples are given of where side shear is smaller than expected and the reasons discussed. Disturbance of the sides of drilled holes due to poor construction techniques and ways to avoid these conditions are considered. Examples of bottom hole disturbance are given and ways to prevent the disturbance are discussed. A graph showing the actual measured capacity of drilled shafts compared to the estimated capacity as a function of the hardness and strength of the soil or rock is presented.

Jan 1, 1999