Search Documents

By Arash Maghsoudloo, Asli Can

"Abstract This paper presents a ground improvement implementation case under a raft foundation of a local hospital. The selected ground improvement method is Wet Soil Mixing (WSM) technique. Soil mixing is increasingly applied to environmental applications and ground stabilization in geotechnical projects. In this technique, weak soil is mixed with cementitious slurry to improve the characteristics of the soil. The investigated case is one of the pioneering WSM ground improvement technique implementation cases in Turkey. The soil profile is mainly consisted of low plasticity clay. The effect of ground improvement is verified by a series of laboratory tests and four in-situ pile loading tests. The results of in-situ pile load tests on constructed soilcrete columns showed an acceptable factor of safety for the bearing capacity of the WSM columns. Measured bearing capacities in all four tested columns were nearly 20% higher than calculated values. In addition, a set of samples are obtained from the constructed columns and unconfined compression tests have been conducted. The laboratory test results indicate that the selected cementitious slurry has a sufficient efficiency to form the stabilizing columns.IntroductionIn the construction industry, stabilization of the soft ground by lime or cement stabilization is a widely used technique. In ground improvement systems deep mixing method (DMM) results in the same stabilization in deep portions of the soft soil profile by mixing cementitious slurry by means of mechanical augers. The pioneering cases of modern deep mixing application can be traced back to the year 1970 that was used for the stabilization of marine soils below the water level for the construction of harbor structures (Terashi et al., 1979). Nowadays, DMM is shown to be a proper and efficient method for the foundation of the structures and embankments on land. Some recent studies also reported that reasonable settlement reduction range in the stabilized soils under the foundation of structures (Archeewa et al., 2011). In addition to reduction of the structural settlement under service loads, deep mixing methods are also utilized when there is a concern with contaminated soil and groundwater or groundwater control (Andromalos and Bahner, 2003).Although, the DMM is shown to be a successful method in numerous studies for improvement of a wide range of soil types such as organics, fine-grained, and coarse grained material, it has some limitations (Archeewa et al. 2011, Jameson et al. 2010, Jelisic and Leppanen 2004, Lambrechts and Roy 1997, Meyersohn 2007, Miki and Nozu 2004, Olsson et al. 2008, O’Rourke and McGinn 2004, Stewart et al. 2004, Yang et al. 2011). High soil density and stiffness could damage deep mixing rigs. Engineering properties of the soilcrete columns changes based on the soil type, water content and other factors such as organic content of the available soil profile, so properties of the generated soilcrete should be verified by a set of rigorous testing procedures (Puppala et al. 2004).Based on the general classifications presented in the ground improvement literature, deep soil mixing method is divided into two main types of dry or wet mixing methods. In the dry and mixing methods compressed air and water are utilized as the binder transporter medium respectively (Moseley and Krisch, 2004). In addition, DMM methods can be categorized based on the employed mixing methods during the construction. In this study, the main aim is to present and elaborate on the selected method is known as Wet Speed Soil Mixing (WSSM)."

Jan 1, 2014

By Wolfgang G. Brunner

The closing of the gap in the European waterway- net is one of the big and challenging traffic projects following the German reunification. The water canals in the North German plain connect the Rhine river, the border between Germany and France, with the Oder, the German border river to Poland. As early as in the 30's of the 19th century the planning and construction of a ship- lift and a canal bridge started, in order to close this last big gap in the system between the Mittelland Canal and the Elbe- Havel Canal near Magdeburg. This main waterway connects the West of Germany, known for its coal mines and steel mills, with the capital Berlin, and from there it goes on into Poland. The building activities started in 1934 but came to a complete stop in 1942 because of the war. The communist government in East Germany was not interested in continuing this huge project, including the ship lock Rothensee, the canal bridge crossing the river Elbe, the former border river between West and East Germany, and the lock Hohenwarthe due to lack of political backing along with low construction capacity.

Jan 1, 2000

By Andrew Port, Ali Ghandeharioon

Nonlinear seismic deformation analyses using the finite difference program FLAC were performed for a wastewater treatment plant to estimate foundation displacement and performance of two proposed trickling filters during the 2475-year event design earthquake. The effective stress based constitutive model UBCSAND, which captures the cyclic behavior of both the “sand-like” and “clay-like” materials, was used to model the dynamic response of the soil strata. Dynamic analyses of the site indicated that in absence of ground improvement or deep foundations beneath the proposed trickling filters, those structures would undergo horizontal displacements in excess of 1 m and short-term differential settlement gradient of about 400 mm over 50 m as a result of seismic and post-seismic settlements. Three mitigation options were considered for limiting the seismic displacements and differential settlement gradients of the proposed trickling filters. These alternatives include vibro-replacement stone columns, vibro-replacement stone columns plus supplementary cutter soil mixing (CSM) configurations, and pile foundations. Various layouts for each mitigation option were considered including the lateral extent of the ground improvement, CSM walls and pile spacing. Seismic horizontal and vertical displacements of the proposed structures as well as post-earthquake consolidation settlements due to dissipation of excess pore water pressures in soil layers were assessed in all the analysis alternatives. The analyses indicate that all the alternatives considered have the potential to provide a comparable level of seismic and post-seismic performance. However, for similar performance levels, the ground improvement options need to extend well beyond the edges of the proposed structures, while the piles can be limited to just beneath the footprint of the structures. INTRODUCTION Annacis Island Wastewater Treatment Plant (AIWWTP) is owned and operated by Greater Vancouver Sewerage and Drainage District and services a population of approximately 1 million people in Vancouver, British Columbia. Wastewater is generated by residential, commercial, and industrial sectors and the treated effluent is discharged to Annieville Channel of Fraser River on the south side of Annacis Island. AIWWTP is located on a 51-hectare site and was commissioned in 1975 as a primary treatment plant, but has had two major expansions to meet the population growth needs, and to improve the treatment process efficiency through the provision of secondary treatment of the liquid stream. The current expansion includes construction of additional solids contact tanks and secondary clarifiers. Future expansions include the construction of proposed additional trickling filters. New expansion structures are required to be designed for post-seismic operation after the 2475-year event design earthquake.

Jan 1, 2018

By A. R. Gaba

Phase I of the Canary Wharf development in London's docklands involves the construction of six fifteen storey buildings located predominantly over water of the West India Docks. The buildings are supported on some 1000 No., 25m long, open ended steel tubular piles driven through 10m of dock water to found in dense sand at a depth of about 15m below dock bed level. The piles are of composite section with reinforced concrete within the upper 17m of the steel tube. Three trial piles were installed in the dock to investigate the driveability and performance of the driven steel tubular piles. The piles were subjected to dynamic and static load testing. Loads were applied in both vertical and horizontal directions. Vibrating wire strain gauges were installed on the inside of the steel piles, on the reinforcement and in the concrete to determine the relative proportions of the applied load carried by the steel tube and concrete infill and to establish how these proportions varied along the length of the piles. Inclinometers were also installed to monitor the lateral deflection of the piles. This paper describes the driving, construction and testing of the three trial piles. The results of the vertical and horizontal loading tests are discussed and comparisons are made between dynamic and static tests carried out on the piles.

Jan 1, 1989

By Francis D. Leathers

Four friction pile load test programs, including 23 tension tests and 9 compression tests, have been performed as part of the Central Artery/Tunnel Project in Boston, Massachusetts. The tests, performed on both precast, prestressed concrete (PPC) piles and steel piles, yielded the following adhesion values: [Soil Type Clay Clay Glacial Till Interbedded Sand and Clay Interbedded Sand and Clay Pile Type PPC Steel Steel Steel PPC Adhesion (psf) 610 to 1,200 230 to 900 220 to 550 680 1,280 ] The adhesion appears to be affected by differences in pile material type, with PPC piles having higher adhesion than steel piles. However, part of the apparent difference for the clay may be due to differences in time between driving and testing. The significant range of test data means that the need for site specific testing to determine or verify design values of adhesion should be considered during design. Creep rates at loads near failure ranged from about 0.02 to 0.18 inches per log cycle of time, with most values in the range of about 0.04 to 0.08 inches per log cycle of time.

Jan 1, 1994

By Hyu-Soung Shin

This study is concerned with the characteristics of the behavior of steel-concrete composite drilled shafts, a material that is used for large bridge foundations, and especially for weak submerged ground conditions. Depending on the loading or boundary conditions considered, the behavior of foundation will vary. The bearing capacity of steel-concrete composite drilled shaft is influenced by initiation and propagation of fractures along the interface between steel casing and filled concrete. The interface effect is taken into account with the following two simplified cases: (1) detached model with free interface (no shear stiffness of interface) between concrete core and steel casing, (2) confined model by an upper steel cap with free interface. In the confined model, it is intended to have an unified behavior of composite shaft between concrete core and steel casing but there is interface between them. Intensive numerical studies have been undertaken to investigate detailed behavior of the composite shaft. In this study, 3-D finite element analysis is employed. Ground conditions typical of those encountered for the design of drilled shaft under water are considered affecting the behavior. Also, an attempt is made to generate possible combinations of the loads which have been considered in fields. Detailed characteristics of the stress and displacement distributions are evaluated to understand the mechanisms of composite shafts.

Jan 1, 2007

By Rick Deschamps

A reoccurring problem with support of excavations in urban areas involves the placement of external support components like anchors or nails in right-a-ways, subway and utility setbacks, in areas occupied by adjacent structures, and within the property of non cooperative neighbors. Such a situation occurred for a project in Arlington, Virginia, which ultimately resulted in the preliminary design of a large footing supported cantilever retaining wall that was extremely costly and impractical to build. An innovative design alternate consisting of a series of vertical concrete elements (VCEs) supported by post tensioned tiedowns was proposed to the General Contractor and accepted by the owner. The VCEs were designed to serve as the main structural elements for both the temporary support of excavation system and the permanent wall. The VCE?s were constructed using single bite diaphragm wall panels oriented perpendicular to the excavation face including a rebar cage and tremie concrete. Threaded inserts were placed within the rebar cage to attach the cast in place exterior wall. Overall stability and lateral movement of the VCEs were controlled by high capacity vertical anchors embedded within the VCE. A detailed instrumentation program was installed to monitor the movements of the VCEs with relation to the excavation depth. The paper present the project case history by discussing the design concepts of the VCE, the construction approaches used to install them, the construction challenges encountered, and the performance of the unique system.

Jan 1, 2008

By V. M. Troughton

Further pile load testing has been carried out at Canary Wharf to compare the performance of base grouted and ungrouted bored piles founded in the Thanet Sand. The testing regime included three preliminary test piles and two working test piles. The results of these tests are summarised in Table 1 below. Two of the preliminary test piles were located only 14m apart to compare the performance of a base grouted and ungrouted pile in similar ground conditions. The load/settlement behaviour of these two preliminary test piles are compared on Figure 1. All the piles were drilled under bentonite with a drilling bucket. In the base grouted piles four grouting tubes were placed with the reinforcement cage to within 500mm of the pile toe. After the pile had been concreted these grouting tubes were then extended to the pile base by drilling and packers were installed. Grout was then injected into the four tubes simultaneously.

Jan 1, 1991

By Ziyad Abunada, David O’Connor, Abir Al-Tabbaa

"Abstract Contaminated land remediation using soil mix technology (SMT) is a relatively recent development which has been shown to be a cost effective and versatile system with numerous environmental advantages over other remediation techniques. The added complexities and variability associated with contaminated sites has escalated the need for field trials, field monitoring and specific QC measures to be undertaken for this setting and was the rationale behind project SMiRT (Soil Mix Remediation Technology). The main aim of project SMiRT was field validation, testing and assessment to provide stakeholder confidence in SMT and increase its uptake for land remediation in the UK. The field trials involved the treatment of 800 m3 of soil, through applying six different remediation techniques with four different SMT systems and introducing over thirty binders and binder compositions with a range of installation methodologies. Various issues were faced during the installation process and which were addressed on site. This paper presents some aspects of early age field observations, field monitoring, in-situ testing, coring and laboratory testing of cored samples and highlights some lessons learnt, providing valuable information on the issues that need to be addressed for this application of SMT.IntroductionAlthough soil mix technology (SMT) was developed in the 1960s in Japan and Sweden for geotechnical applications, its potential in geo-environmental applications became evident more recently the 1980s in the US and in the 1990s in Europe, having since increased to provide a range of remediation systems (Al-Tabbaa and Evans, 2003; Al-Tabbaa et al., 2011). The most common applications to date have been (a) the construction of low permeability containment walls or cut-off walls to contain a contaminated site; (b) stabilisation/solidification (S/S) treatment, with cementitious binders, for physical and chemical encapsulation of contaminants in soils and (c) the installation of permeable reactive barriers (RPBs), which are permeable walls that intercept the groundwater flow and remove contaminants from it, by mixing special additives with the native soil. Contaminated land remediation using SMT is a cost effective and versatile approach with numerous technical and environmental advantages over other remediation techniques. These advantages include the use of simple and well established techniques and equipment, speedy implementation, applicability to sites of any size and to multiple contaminants, elimination of off-site disposal, low risk and low emissions. There is a lack of competing alternative technologies that offer the same level of versatility and economic, environmental and social benefits, under current environmental legislation constraints. In addition, most currently available contaminated land remediation techniques are only partially effective, and are relatively contaminant-specific. This makes SMT a promising and timely contender to lead the market place in offering a cost-effective, efficient and low risk solution to contaminated soil and groundwater remediation and has resulted in a range of recent innovations."

Jan 1, 2014

By Walter Ensinger

Special foundation works is one of the most innovative sectors in civil engineering and construction. Both engineering techniques and construction machinery are undergoing continu­ous further development. These developments are providing ways to meeting the world-wide requirement for special geotechnical works even faster, even better and more efficiently. Unfortunately, accident prevention organisations have had to realise that the figures on in­dustrial accidents in special foundation works are still above average in number. The Safety & Environmental Working Group of the EFFC thereupon started to carry out a survey on acci­dents occurring in this sector and used this information as a basis for the preparation of acci­dent statistics and an accident analysis. The objective of this undertaking is to determine key accident occurrences and their causes and to consequently determine measures for improved health and industrial safety.

Jan 1, 2002

By Yeruva Ramanareddy, Sohail Wajid, Ahmed Shaz, K. Bhavani

"CP-06 is an NATM cross passage which connects up-line and down-line metro tunnels near Kilpauk Medical College, Chennai. It lies completely in loose silty sand to dense sand with water table almost touching the ground surface after Chennai floods. Pre-grouting was done before excavation to seal the area and to ensure no-loose pockets. The heading was excavated successfully but while benching excavation huge water ingress started seeping out. Sand also permeated along with water which became unstoppable due to cavity formation and caused the up-line tunnel to sink considerably. A large grouting exercise was carried out with different grout materials and techniques both from the ground surface and inside of tunnel to stop the water ingress and stabilize the tunnel. This paper describes the chronology of events that occurred in the tunnel during CP-06 issue. It elaborates all the different grouting techniques involved in the whole process of the tunnel stabilization. It includes a finite element analysis using Rocscience RS2 9.0 software showing the possible cause of sand incursion with water from the CP invert which lead to the tunnel settlement. This paper also describes the after effects and the lesson learnt from the whole incident.INTRODUCTIONConstruction of Metro Rails has become the latest alternative to cope up with the transportation demand of the growing urban cities population. L&T SUCG JV constructed Chennai Rail Metro Phase II Contract UAA-04 which included design and construction of approximately 4 km of route length of underground mass transit railway including 3 underground stations. This package also includes 12 cross passages which are NATM tunnels connecting upline and down-line side of TBM tunnel for safe evacuation of passengers in case of emergency. As per NFPA guidelines, this is a mandatory structure and there should be atleast one cross passage in 244m tunnel length.CP-06 is a cross passage connecting upline and downline tunnel between Pachiyappa College Station and KMC Station, in Chennai Metro. During the construction of CP-06, heavy water seepage of around 450 liters per minute was encountered during second round of benching excavation after full heading was excavated. An inflow of around 12-15 cum of sand and silt was also observed inside the tunnel along with the seepage water, which created piping inside the TBM tunnel causing it to settle continuously with time. A huge effort was made to stop the water ingress along with loose sand which was causing the running tunnel to settle, involving all possible grouting methods and temporary support installation."

Jan 1, 2017

By D. P. Nicholson

The current phase of office development at Canary Wharf in the London Docklands includes twelve multi-storey buildings varying from eighteen to forty stories in height. The area of Canary Wharf South comprises five multi-storey buildings with low level in fill podium and garden areas. Three of these multi-storey buildings have "pile-cap" designs where the entire building load is applied to the piles. The remaining two buildings have "piled-raft" designs where allowance is made in the design for part of the building load to be transferred to the raft formation. Using a piled-raft design approach has enabled savings to be made on the number of piles used below the raft. This paper describes the calibration analysis undertaken to validate the design method. The ground conditions at the Canary Wharf site are typically fill and recent gravel deposits over the overconsolidated clay and sand of the Lambeth Group. Below these strata is the Thanet Sand. The Lambeth Group provided the founding layer for the raft and contributed to the pile shaft resistance. The Thanet Sand stratum provided the bearing layer for the 1.5m diameter base grouted bored piles. The piled-raft design required an assessment of the building load transfer through the raft to the formation layer. This load transfer led to significant increases in effective stress in the soil below the raft and thence a corresponding increased the capacity of the piles. This interaction of the raft with the prepared formation contributed to between 27% and 45% increase in total vertical load carrying capacity of the piled-raft substructure compared with the pile-cap design method. The development of the piled-raft design was carried out in three main phases: ? Development of the approach and validation analyses. ? Design work on various schemes resulting in detailed design packages. ? Validation analyses using full 3D finite element analysis (presented herein). The validation of the piled-raft design approach was initially carried out against published case histories for piled-raft interaction. To improve on the validation work a full 3D finite element analysis of a simplified pile raft and superstructure (which contributes stiffness to the raft) was undertaken; the analysis included only a quarter of the structure due to assumed symmetry of the structure and vertical loading. This 3D validation analysis is presented herein. The analysis was carried out using the Oasys LS-DYNA finite element program. Prior to carrying out the analysis of the piled-raft an initial finite element analysis was carried out to back analyse a fully instrumented field pile test providing accurate modelling of a single pile performance. This back analysis allowed confidence in the soil parameters used in the 3D model; comparisons of shaft and base resistances between the pile test and the FE model calculations for the single pile are presented. The parameters provided in this work were then carried into the full 3D model of the piled-raft. The 3D model of the piled-raft structure included 18 piles (12 full piles and 6 half piles on an axis of symmetry of the model).

Jan 1, 2002

By Andreas Andenæs, Arne Schram Simonsen

"AbstractThe Tresfjord bridge is with its variety in foundation concepts and difficult soil conditions one of the most geotechnically challenging projects in Norway at the time. The project comprises design of large concrete caissons, steel core piles through large rock fills, and closed end steel pipe piles in up to 40m water depth driven in very hard moraine. Test piling has also been conducted to check feasibility of the concept, and PDA measurements have been used to verify sufficient capacity of piles. FactsThe Tresfjord bridge is part of the new export road from Ålesund to Åndalsnes on the North-West coast of Norway built by the Norwegian Road Administration. The bridge will reduce travel time with about 30 min between the cities, see Figure 1. The bridge is planned to open summer 2015.The Bridge crosses the Tresfjord and will be 1290 m long. The bridge is built as a free cantilever bridge and will be resting on a total of 20 nos. of foundations, where two are abutments resting on steel core piles, three are casted directly on bed rock and 13 are foundations resting on steel pipe piles. The last two foundations holding the main span will be concrete caissons resting on bed rock and moraine. Figure 2 shows a 3D model of how the finished bridge will look. Multiconsult AS is responsible for design and pile supervision , while the Joint-Venture Bilfinger-Tresfjordbridge ANS is responsible contractor.Soil ConditionsPercussion soundings and sampling together with coring have been performed in the individual foundations using a small geotechnical equipped vessel. Acoustic and refraction seismic profiling have also been carried out to tie in the layers between the boreholes.The soil conditions are varying over the length, but are in general dominated by a soft top layer (2-4 m) of sediments over very hard moraine with occasionally large boulders. Piles in the two foundations closest to shore on the western side of the bridge are piled to bed rock with penetrations up to about 27 m in soil.Water depth varies from about 10 to 40 m for the piled foundations. Figure 3 show how the topography of the seabed varies over the bridges length."

Jan 1, 2014

By W. L. Chong, Y. Zou

There are many types of Earth Retention Systems (ERS) available in the market where more than one method can be a feasible solution for a project. This paper examines the design and construct process of a project in Dee Why, NSW using a hybrid ERS comprising contiguous piles with jet grout infill. The development comprises a deep basement and mixed-use urban superstructure. The site is located in an area of variable ground conditions, high ground water table and in proximity to existing buildings with multi-level basements. This paper details a comprehensive assessment of the geological conditions and strategies adopted to better understand the effectiveness of the proposed product and to minimise the associated risks of the proposed solution. This involved conducting additional geotechnical investigation, extensive numerical modelling and in-situ monitoring of the movements and the performance of the walls. A monitoring regime consisting of inclinometers, survey points on capping beam and prisms on the neighbouring buildings and roads surrounding shoring wall was implemented. The monitoring results were back-analysed using computer software WALLAP, Plaxis–2D and Plaxis–3D for the post-construction examinations. This paper details the effectiveness and advantages of a hybrid ERS using contiguous piles with jet grout infill.

Nov 1, 2022

By J. Matos e Silva

The paper refers five examples of executed diaphragm walls with one to five levels of anchorages. For each example a comparison is made between the results of the design using the traditional criteria and the Eurocode 7 recommendations. A comparison is also made with the behaviour of the diaphragm walls during the construction phase. From the referred examples the author presents his conclusions.

Jan 1, 2002

By Kevin Green, Iván Contreras, Aaron Grosser, Jon Ausdemore, Rachel Leier, Amr Ragy

"Construction of a new tailings dam was required to increase tailings storage capacity at a trona mine near Green River, Wyoming. The new dam was founded on overburden soils underlain by both fractured and competent bedrock. The stored tailings and water had high salt content, resulting in salty seepage water. To reduce the impact of the salty water on groundwater and the Green River, the design of the new tailings dam included a 257,260 SF (23,900 m2) seepage cutoff extending into competent rock.An extensive subsurface characterization was performed prior to completing the design and suitable seepage cutoff methods were evaluated. The approach selected was a full replacement panel using hydromill and clamshell for construction and self-hardening slurry (SHS) for the wall material. Laboratory testing was performed and ongoing monitoring has continued to evaluate the hydraulic conductivity and seepage cutoff performance in the briny environment.The paper includes project background, the collaborative approach and outcomes of the QA/QC program, and the monitoring results for the seepage cutoff wall.PROJECT BACKGROUNDCiner Wyoming, LLC (formerly OCI Wyoming, LLC) owns and operates the Big Island Mine facility near Green River, Wyoming. This underground trona mine has produced soda ash since 1962. The Greater Green River Basin covers much of southwestern Wyoming and extends into northeastern Utah and northwestern Colorado. The Ciner facility is located in the Green River Basin, which is part of the Wyoming Basin physiographic province. The Green River runs to the west and the south of the Ciner facility.Beginning in the early 1990s, Ciner primarily disposed tailings underground in mined-out panels. However, in recent years, underground storage has become limited and some disposal has transitioned to the ground surface. Long-term planning revealed a need to expand Ciner’s surface tailings disposal capabilities. Pond 2, a previously permitted disposal area, was identified as the most viable location for a storage facility. The Pond 2 site is directly north of the Ciner plant facilities, northwest of the active Upper Delta tailings storage facility, and northeast of the Green River (Fig 1)."

Jan 1, 2016

By William Billiet

"The Dulles Silver Line Phase II is an 11.4 mile extension of the Washington Area Metro Transit Authority’s Silver line in northern Virginia. There are three miles of elevated guideway, which are supported on 188 large diameter mono-shafts founded within the Triassic Geologic Aged Culpeper Fault Basin. Three lateral load tests were performed on fully instrumented test shafts. The challenge in developing the load testing program was how to reproduce the effects of the extremely high design loads along the test shafts, considering the limitations of the load test equipment. Development, execution, and analysis of the lateral load test program is discussed.INTRODUCTIONPlans for Dulles Silver Line Phase II include two Aerial Guideway sections on elevated track, the Main Line and Yard Leads. The Aerial Guideways are supported on mono-shafts (single, largediameter drilled shafts) socketed into rock. Lateral loads are resisted primarily through the stiffness of the shaft and the geotechnical resistance of the rock socket. The monoshafts were designed in accordance with AASHTO LRFD 2014. Based on our preliminary analyses, the production mono shafts were expected to consist of 6.5, 7.5, and 8.5 foot diameter drilled shafts with rock socket lengths varying between 8 and 34 feet (averaging 14 feet). Table 1 summarizes the maximum service load combinations for each size production shaft along the aerial guideway alignment.GEOLOGYThe project is located within the Piedmont Province, a major physiographic province on the east coast of the USA extending from Alabama to Pennsylvania. Within the Piedmont, a number of Mesozoic basins formed in rift valleys. Dulles Airport is located in the Culpeper Basin, characterized by a relatively shallow siltstone rock surface compared to the adjacent areas underlain by Piedmont crystalline rocks. The geologic stratigraphy at the load test sites generally consist of residual soils and intermediate geo-material (IGM) overlying siltstone rock. IGM is a term used by Virginia Department of Transportation (VDOT) to describe residual material as it transitions between soil and rock. For the purposes of the load test, the siltstone rock is classified as fractured rock (RQD<50), and competent rock (RQD=50). Table 2 summarizes the stratigraphy encountered at each test site."

Jan 1, 2017

By Hal W. Hunt

Steel and concrete piles and power-actuated hammers have developed almost entirely within the past 100 years. Prior to that time, piles were mostly timber, driven with a drop hammer or a maul. The Engineering News Formula ? for timber piles driven with a drop hammer at a factor of safety of six ? was promulgated by Wellington in 1888. Steel com­panies supplied fabricated and rolled shapes for piles in the early 1900&apos;s. The thin shell and then uncased concrete piles originated about that time. Now leads have become sophisticated to accurately spot a pile at any required batter. Hammers have grown to phenomenal size and vibratories are being accepted at full value.

Jan 1, 1984

By J. A. Elliot

Deep Mix-in-Place soil stabilisation is achieved by forming columns of soil/cement arranged to overlap by secant intersection. Alternate columns are constructed initially and infilled. The cementitious material injected is designed to retard the strength of the resulting mix thereby allowing satisfactory overlapping. Columns are constructed using a designed large diameter mixing auger mounted on a smaller diameter auger stem. This is firstly screwed to the design depth removing only such spoil as to enable penetration of the auger, and subsequently counter rotated and extracted in a predetermined mixing pattern and grout injection rate to ensure continuous and homogeneous treatment through each successive level. The process is performed whilst monitoring auger depth, grout flow and pressure. Cementation Piling and Foundations Limited used this technique to stabilise allu­vium and to facilitate the construction, by conventional techniques, of a circular pumping station pit of 10M diameter to 10M below ground level. The work was carried out within 3M of adjacent domestic properties, and on a very restricted site in Elland, West Yorkshire. Ground conditions consist of 2M of cohesive alluvium becoming water bearing and increasingly sandy and gravelly with cobbles which overlies the mudstones at 10.0m depth. Sandstones beneath formed an aquiclude to artesian ground water with the underside of the open excavation approxi­mately 1.0M from the top of this material. Peripheral treatment into the mudstone, coupled with pressure relief wells, proved successful and final excavation depth was achieved in "the dry".

Jan 1, 1989

By Scott C. Vollmer

This paper seeks to examine some of the technical factors influencing the deflection of Mechanically Stabilized Earth (MSE) retaining walls based on the authors&apos; field observation of numerous structures. Excessive deflections can be unsightly and can be perceived as wall failure. Deflections can cause cracking or gapping of the facing units and general misalignment. Deflection of the reinforced backfill zone behind the wall face can result in settlement of the backfill zone and adjacent pavement cracking. Deflections can be the result of excessive movement external or internal to the reinforced soil structure. This paper only examines internal factors affecting wall deflections. External factors such as foundation settlement are not discussed.

Jan 1, 2003