Search Documents

Jan 1, 2004

By Fred Fuchs

"Most deep foundation work is either unseen by the general public or viewed as an inconvenience in their daily lives. Hurricane Katrina changed that perspective for everyone in New Orleans — and many other people in the U.S. and abroad. The public and the government of south Louisiana, and the U.S. Army Corps of Engineers (USACE), all needed to restore trust in the system that protects their property and, more importantly, their lives. While much has been written about the failures of government agencies, in this case incredible solutions were devised and implemented despite daunting schedules and arduous conditions. These solutions were achieved through collaboration, and through the efforts of USACE, where the goal was to fi nd the most expeditious and effective design/build solutions. This disaster thrust the pile driving industry into the national spotlight. Boh Bros. Construction Co., L.L.C., along with numerous local and national heavy construction companies, subcontractors, material suppliers and government agencies, take pride in the milestones reached after Hurricane Katrina.The majority of New Orleans’ population lives below sea level. Historically, the city has been protected by a fl ood control system consisting of earthen levees and I-walls (steel sheet pile topped by vertical concrete wall). Rainwater is pumped out of the city over this protection system and into canals that feed into Lake Pontchartrain. On August 29, 2005, when Hurricane Katrina made landfall just east of the city, the levee system experienced a major failure of several I-walls lining the outfall canals, causing flooding of 74% of the east bank of the city. The counterclockwise rotation of the wind pushed the lake water onto the south shore, raising the level of water more than 10 ft (3 m). A failure of 450 ft (137 m) of floodwall lining the east side of the 17th Street Canal caused extensive damage. This breach prevented the use of the pump stations that outfall into the 3-mile (4.8 km) long 17th Street Canal."

Jan 1, 2008

By Jeff Starchuck, Harald Kullmann

"In 2005, an inspection showed that the Deception Bay Wharf in the Canadian Arctic was at the end of its service life. Although Deception Bay is closed with landfast ice up to 5 ft thick, shipping operations continue year-round, with additional voyages in the summer open-water season to supplement mine supplies. The rehabilitation scheme that allowed minimal interruptions to shipping involved concrete caissons cast on barges and an ingenious placing system.WorleyParsons Westmar of Vancouver, B.C., performed the inspection under contract to the owner, Xstrata Nickel, Montreal, Quebec. The wharf, on the coast of the Nunavik region of Quebec, was originally constructed in 1971 for an asbestos mine, and is now used to support Xstrata’s Raglan nickel mine, importing fuel for p o w e r g e n e r a t i o n a n d general mine supplies, and exporting nickel concentrate to smelters in the south. Emergency repairs were essential to allow operations to continue at the site, while the parties considered permanent rehabilitation options and secured funding. The repairs were done in the openwater seasons, and included reinforcing the failed interlocks above water level with steel patch plates and injection grouting of the cell fill below the port crane in 2005. In 2006, workers installed a circumferential belting system below water level.Westmar held critical planning sessions with the mine operation personnel to find ways to stretch the limits of the mine supplies and nickel storage facilities. In the end, the parties agreed to shut down construction activities four times during the ice-free season to allow access to the dock site.Westmar developed a plan that allowed mine operations to continue during construction, and Xstrata approved the plan and budget in September 2006, for execution in 2007. Rapid construction was essential. To accommodate the short construction season and maintain minimum levels of service for the mine, the work was radically different from conventional Arctic deep-sea port construction. Like the original Deception Bay Wharf, construction practice was to use steel sheet pile circular cells with the consequential heavy support services for the labour force. Construction duration was typically two seasons. The plan for Deception Bay was executable in one season based on a concrete caisson structure. Only a modest amount of schedule float was needed."

Jan 1, 2009

By Kevin W. Cargill

In September 2004, Hurricanes Frances and Ivan caused the Pigeon River in western North Carolina to flood. This flooding eroded the embankment below Interstate 40 (I-40) and sent one of the eastbound lanes, along with the roadway shoulder, into the river below the embankment. North Carolina Department of Transportation (NCDOT) needed to reopen all the lanes of I-40 as soon as possible and considered this damage to be an emergency situation. NCDOT contracted Schnabel Foundation Company to design and build a repair that would keep this important interstate open and reestablish the eastbound lane. The obstacles included limited work room, the requirement of keeping the remaining lanes of I-40 in service, and producing a final product that would be relatively maintenance free and last at least 100 years. The proposed repair had to consider that the existing interstate was founded on a rock fill that was constructed from rock blasted off the adjacent mountain side. The selected design included two, tied-back micropile walls to address these obstacles and other issues. Each of the walls were constructed of 10.75 inch diameter micropiles and corrosion-protected tieback anchors installed through the existing rock fill into competent bedrock, concrete wales, and a reinforced shotcrete facing. This successful project was completed during the coldest months of the year and within the timeframe established by the State of North Carolina. This paper will discuss the design and construction of the repair and the many challenges that had to be overcome.

Jan 1, 2006

By Don Deardorff, Ke Yang, Yingcai Han, Ken Sorensen, Robert Kruger, Mark Petersen, Diane Fiorelli, Larry Goldfarb, Kathryn Petek, Kwabena Ofori-Awuah

Design of deep foundations for lateral loads requires an understanding of soil-foundation-structure response during loading. Lateral loads on a deep foundation (piles) could be due to earthquakes, winds, waves, and/or machine vibrations. Over the years, analysis of response of piles due to lateral loads evolved from closed-form solutions to p-y methods to strain wedge to finite element/finite difference modeling. Although analysis of lateral response of piles and shafts is routinely performed, there is no single guidance document and/or standard for design and testing. Several different analytical methods are available for the analysis, and the resulting design can result in significantly different responses which can create confusion. This is especially true for analyzing and designing piles in potentially liquefiable soils with lateral spread issues under seismic conditions.This guidance document is intended to assist geotechnical engineers, pile designers, and contractors in analysis, design, and testing of piles and drilled shafts for lateral loads. This document discusses the background of different analytical and testing procedures and presents the recommended methods for analysis, design and testing of piles for lateral loads.Chapter 1 defines the different kinds of lateral loads to which a single pile or pile group may be subjected. This first chapter also presents different types of piles used to resist lateral loads.Chapter 2 discusses geotechnical issues related to lateral pile design such as liquefaction and lateral spreading and other non-seismic issues. Also addressed in Chapter 2 is geotechnical site characterization (as related to lateral loads) in terms of site investigation, in-situ testing, geophysical testing, laboratory testing, and estimation of soil/rock properties.Chapter 3 discusses the background and available analytical methods and tools for the analysis and design of single piles and drilled shafts. Several methods of analyses from closed-form elastic solutions to the finite element/finite difference solutions and their applicability are discussed. Available commercial computer software packages for analyzing single piles and drilled shafts are also presented.Chapter 4 expands the discussion of single piles and drilled shafts into the analysis and design of pile groups. In addition, group effects, resistance of pile caps, results of previous experimental and analytical studies, and available analysis tools and software for pile groups are discussed.Chapter 5 presents the issue of lateral resistance of piles and drilled shafts as discussed in different national and international building and non-building codes. A summary of extensive research on several codes are presented to facilitate the compliance with different codes.Chapter 6 discusses structural design issues of individual piles and drilled shafts such as depth of fixity.Chapter 7 discusses soil structure interaction issues related to kinematic and inertial effects due to seismic loading and available methods of analyses.Chapter 8 discusses and presents the typical procedures for the lateral load testing of piles. This guideline was developed as an aid to the practicing engineer in providing information, direction and commentary on the lateral design of deep foundations. Although all reasonable effort has been made to accurately compile the material and information contained herein, no warranty is made with regard to any such material or information and the Deep Foundation Institute assumes no responsibility for any possible errors or any direct or indirect result of the use of any such material or information. It is not intended that this document address every factor affecting lateral design for every situation. Therefore it is the responsibility of the person utilizing information from this document to confirm that it is appropriate and correct for their situation as well as to understand and properly apply

Jan 1, 2012

By James Warner

Investigations of the sinkhole indicated that the loose, disturbed ground was completely encircled by dense competent core. This confinement substantially increased the effectiveness of the compaction grouting compared to what might have been expected at a "greenfield" site. However, the 8 ft diameter circle shown in the plan view was only the surface expression of the sinkhole proper and the deep, loosened ground actually extended to a larger diameter of about 20 ft. The planned spacing of the grout holes was based on the finite element simulations using a target void ratio of less than 0.3 throughout the compacted ground within a 5 ft radius of the grout injection point. Because of the strong confinement effect, the layout of grout holes included one central primary hole surrounded by six secondary holes at a triangular spacing of about 5 ft. Since the disturbed ground was considered a confined cylinder, it was anticipated that the primary hole would perform the majority of work and the secondary holes would act as check holes, with progressively lesser grout takes as the loose ground densified.

Feb 10, 2003

By John Vickers, William H. Hover, Paul C. Schmall

"Any sudden subsurface issue that threatens the stability of existing buildings or infrastructure is cause for immediate investigation and prompt remedial action. Nowhere is this more true than the nation’s dams and levees. A breach of any kind, no matter how small initially, has the potential to be catastrophic and impact a wide downstream area. Addressing the problem quickly and effectively is therefore critical. When a turbid water discharge developed from a rock drainage embankment at the toe of the earthen dam impounding Cannonsville Reservoir, near Deposit, NY, the source of the problem was quickly identified as resulting from an artesian water release from an underlying permeable silty sand and gravel formation during drilling of three exploratory boreholes in preparation for construction of a hydroelectric plant at the downstream toe area of the dam facility. Work was halted, intense 24-hour monitoring was implemented, and as a risk reduction measure NYCDEP began to draw down the reservoir’s total storage at a rate of a billion gallons per day. Input sought from contractors within the geotechnical community helped result in the design and development of a deep well system to control the artesian pressure. Once this primary objective was accomplished, modified compaction grouting was performed at the borehole locations to densify loosened soils, fill any voids created by the discharge activity, and seal off the permeable aquifer. This paper discusses the dewatering program, specialized drilling techniques required, monitoring and verification of pressures within the dam, and the grouting program.BackgroundCannonsville Dam, owned and operated by the New York City Department of Environmental Protection (NYCDEP), is located in Deposit, New York on the West Branch of the Delaware River and impounds the Cannonsville Reservoir. Built between 1959 and 1964, the dam has an impervious central and upstream core zone keyed into the glacial till foundation, a semi-pervious downstream embankment zone, and a rockfill toe and is approximately 2,800 ft (853.4 m) long and 175 ft (53.3 m) high. The dam is formed by two embankment sections. The left section forms the main embankment blocking the main river channel, while the right section is constructed over a topographic saddle or low ridge. Reservoir level is actively influenced by withdrawals through the West Delaware Tunnel, based on water supply need. Under normal circumstances, water is continuously discharged downstream to the Delaware River."

Jan 1, 2016

By Tara Schenk-McFarland, Mark Bliss

Echo Dam, located near Coalville, Utah, is a facility that provides storage for irrigation and municipal use. Original construction of the dam was completed in 1931. Because of seismic concerns, the spillway crest structure and upper chute section, founded on old landslide and colluvial material, were recently replaced. Prior to replacement of these structures, jet grouting of a block of the loose and potentially liquefiable soils, directly beneath the spillway crest structure was selected as the preferred alternative to address the potential for settlement and cracking of the spillway crest structure. The replacement or alteration of the in-place soil reduces the likelihood of seismic-induced excess pore pressure development and subsequent settlements. Core drilling and sample recovery of the production jet grouted columns was completed to verify compliance with the specifications. It was recognized that due to the larger rock sizes within the deposits that full homogeneity of the jet grouted zone was unlikely to be achievable. However, the purpose of this jet grouted section was to strengthen enough of the soil so that widespread liquefaction does not occur. During the jet grouting production many instances of ground fracturing occurred. Fracturing was evident based on grout/air bubbles exiting the surface near some of the grout holes during jet grouting, air bubbles appearing in the spoil pits, and lifting of the ground surface in the vicinity of the monitor during the jet grouting process while the system was pressurized. In one instance, a section of the upstream spillway slab, which was left in place, was cracked due to pressurized grout escaping beneath the slab. The overall results of the jet grouting were satisfactory despite difficulties encountered. The cause of the fracturing is hypothesized and a recommendation is included to reduce the likelihood of this occurring on future jobs.

Jan 1, 2017

By Paul Thurlow, Richard K. Lipscombe

The measurement of deflection of designed diaphragm walls is critical for near real time information to assess wall and soil behaviour as the internal area is excavated in a controlled manner. Data enables the site team and designers to check performance of the design, which is linked to safeguarding the site and the external stakeholders.This paper documents the use of Shape Accel Arrays at the Tottenham Court Road Western Ticket Hall during excavation and propping within the diaphragm wall for the Crossrail project. It shows how the data obtained was used within the site settlement management plan to assist in the control of the works and the information used for Value Engineering purposes that benefitted the project.The use of Shape Accel Arrays for measuring the deflection of retaining walls is not commonplace in the UK construction industry, with the Tottenham Court Road Western Ticket Hall being one of the first times they have been used in such a way. A detailed analysis of the data obtained from the instruments has been undertaken, and compared to the results obtained from the manual inclinometers that were read next to the SAAs. The advantages of the relatively new SAAs have been discussed, as well as other applications of the instrument.

Jan 1, 2017

By Seth Robertson, Daniel Belardo, Travis Coleman

Thermal Integrity Profiling (TIP) is a non-destructive method used to evaluate drilled deep foundation integrity. This integrity testing method is specified more frequently, and is becoming an industry standard in the transportation and private construction sectors. This testing method utilizes heat generated during the concrete/grout curing process to assess deep foundation integrity over the evaluated length. With compilation of the measured temperature versus time and installation records, a model of the Effective Average Radius versus measurement depth is generated. The generated effective shaft model is highly dependent on specific construction details, subjective modeling parameters, and proper interpretation of concrete/soil heat dissipation characteristics. Key components of the TIP analysis include both qualitative and quantitative assessments. Qualitatively, variations or sharp reductions in temperature profiles may indicate potential anomalous regions. Quantitatively, a correlation is established between measured temperatures and estimated Effective Radii for subsequent integrity evaluation. Best practices in processing the TIP measurements are presented, including selecting the optimal time for analysis, normalizing the thermal profile, and proper interpretation of potential anomalous regions. Recommendations for implementing mitigation efforts and interpretation of the TIP results are presented.

Sep 8, 2021

By Nicolas Moscoso, Gerald Verbeek, Marcel Bielefeld, Rob van Dorp

Upon recently, most offshore foundations were based on a number of driven piles that were installed with an impact hammer. With the increase in offshore windfarms two major developments have occurred: the shift from jackets to monopiles, leading to increase of the diameter of the foundation piles, and a shift from impact hammers to vibro hammers. As the use of vibratory hammers is becoming more and more common practice, the need for accurate vibro-driving simulation software has increased, which requires that the soil modelling is enhanced to address soil fatigue during pile driving and to predict reliably the soil behavior and resistance during pile driving. In addition pile driving monitoring, which is routine for piles driven with an impact hammer, needs to become common practice. This paper addresses advances in soil modelling that allows more accurate pile driving simulation as well as the application of Vibro Driving Analysis (VDA) or Monitoring (VDM) to validate the simulation results. This is illustrated by a case study of the test pile for the Delft Offshore Turbine project, a 28 m long monopile with a diameter of 4 m that was driven 15 m into dense sand layers using a vibro hammer. After some 6 months the pile was extracted, and pile driving simulations and VDA were done both for the installation and extraction phase. 1. INTRODUCTION At the end of 2017, the total worldwide offshore wind power capacity was 18.8 GW [1]. The vast majority of offshore wind farms are currently in Northern Europe, which together account for over two thirds of the total offshore wind power installed worldwide, followed by East Asia, while developments in North America are still in very early stages.

Jan 1, 2019

By Maurice Guillaud

The most striking innovations on diaphragm-wall construction plant are those associated with continuous real-time trajectory monitoring of the excavating tool (either a grab or a hydro-cutter). The recent equipments are fitted with clinometers and gyrometers to control deflection, rotation or deviation from the vertical, thus allowing to install diaphragm-walls with a verticality accuracy of less than 0.3%. One of the greatest advantages of extensive use of on-board IT systems on the Hydrocutters and hydraulic grab machines is that it aids quality control by automatically producing complete real-time reports of all excavating data (verticality, depth, type of ground, rate of progress, stoppages, etc.). These reports are available to the Engineer, providing the total transparency required for Works Supervision and the Quality Assurance Plan. They also provide the Contractor with input data for databases used for optimising efficiency and progress criteria on future jobs.

Jan 1, 2002

By Jim Bruce

No answer required. From the drilling equipment suppliers, but the specifications must be tailored to be project-specific. Yes, the sonic technique is very interesting as we said, and it is not so much as an issue of the magnitude of power, it's about the efficient use of the power. The efficiency of the machine is not necessarily related to size so it is best to talk to the two contractors that supply the service about that. I think it can be scaled down but it is quite a big head, so therefore there are practical limitations on the size of the door it can walk through and also the size of the casings and rods that it can use. You might defeat the economic advantages if you were to use too short casing lengths. Boart Longyear have a low head room machine that can work within an 8 foot verical clearance.

Feb 10, 2003

By Dave Paul

Dam rehabilitation involves a range of design, construction, and operation risks, some of which are not encountered in new dam construction. These risks can have significant impact on project schedule and project budget. Owners, engineers, and contractors need to understand these risks. Existing dams typically were designed in an era of design and construction standards that have been upgraded and changed. Modern standards will impact the construction approach taken and involve understanding the earlier standards. Knowledge of historical standards/practices as well as current design standards and construction methods is valuable for developing and designing rehabilitation components. Construction records and as-built drawings are valuable when they are available. Rehabilitation projects often consist of older projects where as-built documents or construction records are not available. Where these records exist, many (most) times, they do not fully reflect the current conditions within the dam and appurtenant works. leading experienced practitioners to “expect surprises” both during investigation of the existing facility, as well as during construction. “Surprises” should be expected even when historical records of investigations, design and construction are available. Unknowns, be they known unknowns or unknown unknowns, can be planned for by developing an approach for the design and construction process to identify potential issues/problems, or at least alert the designer and contractor of potential issues. A Risk-Based approach applied for the entire life of the rehabilitation project can be used to alert the parties of potential “surprises” and provide direction for mitigating issues as they arise. This type of approach is particularly effective when the process includes senior practitioners with decades of design and construction experience in all aspects of dams. Minimizing impacts created by “surprises”, particularly during construction, can result in an improved project meeting budget and schedule goals and design standards. This paper identifies and categorizes risk types salient to dam construction, reviews the process of risk identification and analysis, discusses guidelines for risk allocation, reviews strategies to mitigate risks, presents several case studies where risk mitigation strategies were employed successfully (or unsuccessfully), and presents lessons learned. The paper concludes with a summary and recommendations for best practices for Project Risk Management and mitigation that can be used by: Owners; Design Engineers; and Construction Managers, in planning, design, pre-construction and construction phases of dam related projects.

By Takefumi Takuma, Ali Fayad, Shigeru Kambe

"This paper discusses the unique design and construction circumstances of the cantilevered dual sheet pile walls and the Accordion Sheet Pile Wall for the repair and upgrade of the East Garden Grove-Wintersburg Channel in Huntington Beach, California that was concluded in 2014. It also describes the 2008 Emergency Sheet Pile Project for the same channel. Both projects utilized the Press-in Piling Method for its low noise and almost no vibration advantages.BackgroundThe East Garden Grove-Wintersburg Channel is part of the Orange County Flood Control District (OCFCD) and is operated and maintained by OC (Orange County) Public Works (see Figure 1 for its location). The channel, referred to as OCFCD facility # C05 (C05), had suffered significant toe undercutting and slope erosion of its levee due to a series of storms. These began after the facility was constructed in the 1960’s and culminated in 2005. Consequently, the levee was deemed significantly deficient and was eventually declared as a local emergency in 2007. C05 was an incised channel and its levee was constructed primarily from native materials. Operation and Maintenance (O&M) personnel notified the design staff at OC Public Works to be aware of major consequences associated with the dilapidation problem in the most downstream reach of the channel in the vicinity of the Bolsa Chica Wetlands Restoration Project. In 2007, the Orange County Board of Supervisors declared a local emergency to fix the levees with sheet piles to be driven by the Press-in Piling Method, hydraulic pushing piles into ground by holding onto previously installed piles. The project that ensued represented the first in-tandem use on the West Coast of the United States of the Press-in pile driver with its GRB System (Press-in pile driver, a support crane and pile transporter travel on top of already-driven sheet piles). This is further discussed in this paper in the sections titled “Press-in Piling Method” and “GRB System”, respectively. The project repaired approximately 3,800 feet of erosion on the north levee of C05 with 45-foot long cantilevered sheet piles. The sheet piles design constraints are discussed in this paper in the section titled “C05 2008 Emergency Sheet Pile Project (Phase 1)”. Between 2012 and 2014, another mile’s worth of levee reach was improved with the Soil-Mix-Sandwich (SMS) Method. This concept consisted of deep soil cement mix (DSCM) columns sandwiched within the dual rows of sheet piles. Additional details on the SMS, its DSCM construction, and its hybrid geo-structure design concepts are well beyond the scope of this discussion, which is primarily focused on sheet piles. Instead, the interested reader is referred to two papers on the SMS and its DSCM metrics (Fayad, 2015; and Arora, et al., 2015). These were presented and published in the Proceedings of the Deep Foundations Institute (DFI) 2015 Conference on Deep Mixing. Hence, in the section of this paper titled “C05 SMS Dual Sheet Piles Project (Phase 2)” only the sheet pile design constraints of the SMS are covered. Finally, in the area where the project traversed the Alquist-Priolo zone of the Newport-Inglewood tectonic fault, an expandable and deflectable sheet pile wall was used to isolate the flood channel from the Bolsa Chica wetlands. Its details are addressed in the section titled “C05 Accordion Sheet Pile Wall (Phase 2)” of this paper."

Jan 1, 2017

By Ashirbad Satapathy, Sanket Rawat, Ramanand Shukla, Ravi Kant Mittal

Bearing capacity factor (Nq) and Adhesion factor (α) are the key parameters for analyzing the load carrying capacity of pile foundations embedded in cohesionless and cohesive soils respectively. Numerous models are available in the form of charts or equations for the computation of these parameters and hence, have been adopted by most of the International and National standards. Indian Standard for the Design and Construction of Concrete Pile Foundations, IS 2911–Part 1 (2010), also makes use of charts detailed in its Annexure B. However, the sources of these charts have not been specified clearly, making it difficult to back-refer to the actual models to assess their basis for resolving any critical scenarios encountered during design. The present study aims at acquiring a distinct understanding of the development of these charts in order to bring more clarity to the design process of pile foundations. The given charts have been compared with various models specified in existing literature and international standards for the calculation of Nq and α for both driven and bored piles and hence, the basis of Indian Standard charts has been identified. Moreover, it is evident that the use of these charts complicates the process of automation of analysis and design of pile foundations as well as the associated optimization studies. Additionally, the manual entry of data especially, from the logarithmic graph of Nq, escalates the chances of error thus, making it a critical concern for design offices. Therefore, this paper also presents a non-linear regression model for Nq and α, developed using NCSS software for both driven and bored piles. Through multiple iterations, the value of coefficient of determination for Nq and α has been found to reach greater than 0.995. The developed equations can be simplistically used for both manual and automated analysis of pile foundations.

Nov 1, 2022

By David M. Rempe

The purpose of this standard is to provide a method for testing of cushion materials that leads to uniform results when employed by various organizations and laboratories. The load-deflection characteristics measured using this method are intended to provide input data for analysis of pile driving, as in wave equation analysis of pile driving. It should be recognized, however, that there are several factors which may cause a difference in performance between the test samples under laboratory conditions and actual cushion materials under pile driving conditions. These factors include variations in material properties from sample to sample, compaction and/or deterioration of the materials with use, eccentric loading due to misalignment, confinement effects or the cushion container or inter layered materials, head buildup, rate of loading, etc. In order to obtain representative load-deflection characteristics, therefore, testing of cushion specimens which have been subjected to actual pile driving conditions is encouraged 1 such specimen should be tested at various stages of the useful life of the cushion. The users of the data are cautioned to determine if the particular wave equation program they are using requires either the secant or tangent definition of the stiffness and modulus of elasticity.

Dec 1, 1984

By Frank J. Purcell

“Down The Hole” (DTH) hammer drilling is often necessary to advance the casing during pile construction where the test bores have determined difficult drilling conditions with obstructions such as boulders, cobble and glacial till. The use of compressed air to operate DTH hammers in foundation drilling has been a contentious point in many regions of the world due to its potential to disturb the ground around the pile being constructed. There are many examples of damage to adjacent building foundations where compressed air exiting the pile being drilled disturbed the subsurface around the building’s existing piles. This paper looks at the use of compressed air in DTH hammer foundation drilling and the move towards controlling the exhausted air to avoid over drilling the pile, causing potential damage to nearby piles. Simulated models of air flow penetration into the soil of different configurations of drill bits are discussed to highlight design changes employed to better control the air during the drilling process. A case study of the construction of a water-tight pipe pile wall for a building’s underground parking structure is studied to demonstrate the potential of DTH hammer foundation drilling where the air is fully controlled.

Nov 1, 2022

By Nils Schneider, Marc Peters, Stefan Frey, Andrea Fluck

Due to the worldwide population growth, the development of sustainable infrastructure and the exploration of renewable energies plays a key role to handle the rising megacity trends and to limit carbon footprint. Herrenknecht AG is a leading manufacturer of Tunnel Boring machines and has constantly endeavored through its extensive Research and Development programs to address limitations faced by the civil engineering industry as regards to construction equipment capabilities. New mechanized technologies, mainly coming from the tunnelling industry, have been developed by Herrenknecht AG as an efficient alternative to conventional civil engineering, where tailor-made concepts are required to comply with restricted conditions onsite. Very often this innovation led technology capability has meant making construction processes safer due to minimal human intervention and also far more productive due to higher performance as compared to other latest or conventional methods of construction. The rising need for even higher building structures and large-capacity bridges involve the development of innovative deep foundation technologies for on- and offshore operation. Conventional methods like bore piles reach their technical and economic limits under certain conditions. For building shafts and foundations, the mechanized Vertical Shaft Sinking Machine technology (VSM) from Herrenknecht AG is a proven innovation and has now been used in various onshore infrastructure projects worldwide to construct a total of 94 circular shafts in depths of up to 115 meters. It operates below the groundwater level, completely remote-controlled from the surface in a diameter range from 4.5 to 18 meters. Subsequently Herrenknecht noted that Offshore foundations, especially in non-drivable ground conditions such as soft and hard rock (e.g. limestone, sandstone, mudstone, granite etc. or soft soil with high density) and shallow continental shelf (water depth approx. 20-60m), presented construction challenges and equally an opportunity for building high performance equipment. The latter construction conditions usually requires drilled installation methods for applications such as harbor enlargements, bridge foundations and foundations for offshore wind turbines. The Offshore Foundation Drilling technology (OFD®) is Herrenknecht’s latest innovation, incorporating our learnings from the VSM and full-face Tunnel Boring machines, and the OFD® enables a rapid and economical offshore installation in such variable ground and rock conditions. This paper will discuss the technology behind the new mechanized technology of VSM and Herrenknecht’s latest innovation of the OFD® along with their respective application fields in foundations construction. The paper will further present in details, their range of benefits to the construction industry.

Nov 1, 2022

By Donald Bruce, Alex Reeb, George Filz, Wesley Schmutzler, Mitsuo Nozu

"One million seven-hundred thousand cubic yards of deep mixing were installed to support an elevation raise of an earthen levee known as LPV 111, which is located in east New Orleans. The deep mixing was done by two contractors using somewhat different technologies, but producing elements of the same size. As part of the quality control and quality assurance program, 507 deep-mixed elements were cored and 5,082 specimens were strength tested in unconfined compression. This paper presents data from the coring and testing program. Very high percentages of the core run lengths were recovered, except during one period for one mixing technology. The coring methods are described, and reasons for the isolated episode of low recovery are discussed. The strength data show that the specification acceptance criteria were satisfied. Statistical parameters of the strength data are provided, and trends between strength and the following factors are discussed: depth, soil type, binder factor, and project-specific experience. Photographs of longitudinal cuts of core specimens are presented. Important lessons learned from this unusually large project are described.INTRODUCTIONThe Lake Pontchartrain and Vicinity Hurricane Protection system included a project known as LPV 111, which is an approximately 5-mile long segment of levee and floodwall located in east New Orleans along the Gulf Intracoastal Waterway and adjacent to Bayou Sauvage National Wildlife Refuge (Cali et al. 2012). The majority of the project consisted of a raise of an existing earthen levee from an existing crest elevation of about 18 ft to a new crest elevation of about 28 ft. The underlying soils were weak and compressible, providing inadequate support for the raised levee. Ground improvement in the form of deep mixing was selected to provide the necessary stability and settlement control for the raised levee.The US Army Corps of Engineers (USACE), New Orleans District, was the governmental agency in responsible charge of the project, including approval of design, construction, and payment. The lead designer was URS Corporation, and the general contractor was Archer-Western-Alberici (AWA), working in alliance with TREVIICOS South (Trevi), who, together with Fudo Construction (Fudo), performed the deep mixing.As part of the quality control and quality assurance program, over 500 production deep-mixed elements were cored, the cores were carefully logged, and over 5,000 unconfined compression tests were performed. In addition, selected specimens were carefully photographed before and after longitudinal saw cuts to expose the interior of the specimens. This paper provides a summary of the coring and testing performed on the production deep-mixed elements."

Jan 1, 2015