Search Documents

By Piotr Kozlowski, Stanley L. Worst, Matthew J. Niermann

Circular secant pile shafts were installed along the tunnel alignments for both the Ohio Canal Interceptor Tunnel project in Akron, Ohio and the Ohio River Tunnel project in Louisville, Kentucky. The diameters ranged from 34 to 51 feet and the depths ranged from 49 to 107 feet. Verticality and concrete volumes were measured on all piles to verify compliance with the design, which for some shafts consisted of a finite element model with multiple openings using unreinforced concrete secant piles. All secant piles were drilled into rock to seal off the groundwater. This paper will discuss the design, construction and quality control of the secant piles for these projects. INTRODUCTION Many Midwest and Northeast cities have Combined Sewer Overflow (CSO) systems which discharge pollutants into waterways during wet weather events. One way to remedy this issue is to provide a temporary overflow tunnel. A temporary overflow tunnel connects to the combined sewer system and collects the overflow during wet weather events, storing the wastewater until the event has subsided. After the storm event, the stored wastewater can be pumped to the treatment facilities and processed as normal. Project Background – Akron, OH The Ohio Canal Interceptor Tunnel (OCIT) project was performed as a result of the Environmental Protection Agency’s (EPA) Consent Decree with the City of Akron, Ohio. This Consent Decree required modification of the existing Combined Sewer Overflow system. The resulting project consisted of a 27- foot diameter tunnel with multiple points of entry to capture the sewer overflow and prevent it from entering waterways. The tunnel is over 6,000 feet long and is as deep as 150 feet below the ground surface; see Figure 1 below.

Jan 1, 2019

By Zhang Yaonian

This paper describes full-scale tests on ten large bored piles with grouted end conducted for three projects in the urban area of Fuzhou city. Test program included site investigation, pile installation and end grouting. The piles were instrumented with strain gages and load cells to determine load distribution in the piles. Test results showed that end grouting improves load-settlement performance of bored pile. End grouting significantly increases the shaft resistance near the pile end. The better the end condition, the greater the shaft resistance. The average shaft resistance of the bored piles with grouted end is much higher than that of piles without grouting.

Jan 1, 2004

By Padmavathi V. Sagi

In this paper, effect of cyclic loading on the behavior of a long, flexible, unrestrained vertical pile loaded laterally in soft clay is examined. For cyclic loading, the analysis is carried out using a new method for the construction of p-y curves and for static loading conditions, p-y curves proposed by Dewaikar and Poonam (2005) are used. An iterative analysis is employed with secant modulus approach using a matrix method known as moment area method developed by Sawant et al. (1994). For pile top deflection of 20% of pile diameter, the load values are computed for both static and cyclic conditions. The comparison of results with the field test results reported by Matlock (1970) shows a good agreement. A parametric study is further carried out to examine the effect of load eccentricity, pile embedment length, diameter and the number of cycles on the pile response. The results of this study are discussed in the paper.

Jan 1, 2006

By Takefumi Takuma, Tsunenobu Nozaki, Masashi Nagano

The city of Naruto in the southwestern part of Japan is situated at the mouth of the mighty Yoshino River. An approximately 1,000m-long levee/bulkhead along one of the river’s tributaries in the city was raised with prefabricated steel panel walls on a concrete base bulkhead. Some sections of the walls’ foundations were combi-walls made of sheet pile cut-off walls and interspaced pipe piles; both of which were installed with press-in piling because the new wall alignment was very close to existing homes and businesses. A Clamp Crane, which clamped onto already installed piles and moved forward and backward on them, was utilized for a segment where the access to its piling location was too tight for a conventional crane or a track-mounted pile driver to maneuver.

Sep 8, 2021

By Padmavathi V, M. Najamuddin, M. R. Madhav

Granular piles are one of the leading ground improvement techniques, adopted for the betterment of bearing capacity and reduction in settlements of the foundations and also to accelerate consolidation of the surrounding soil. In the recent past, there has been extensive research on the settlement analysis and behavior of granular piles under varied soil conditions. The application of these theoretical solutions to practical problems requires a knowledge of representative values of the deformation parameters of the ground and the granular piles. However, very little information is available on these parameters. The paper presents a new method for the estimation of the modular ratio of granular piles and modulus of deformation of the surrounding in-situ soil from the compression load tests. The load - settlement response obtained from the compression test results are used in the back analysis for estimating the modulus of deformation of the ground. The presence of granular bed, under the rigid plate for load testing, has been given due consideration in quantifying the proportion of load transferred on to the stone column. Based on these considerations a new method is developed to estimate the modulus of deformation of the ground and the modular ratio of the granular pile.

Sep 1, 2022

By David A. Staab

Numerical modeling was used to investigate the feasibility of using two geophysical imaging techniques, cross-borehole ground penetrating radar (XBGPR) tomography and electrical resistivity (ER) tomography, for detecting and characterizing defects in deep-mixed soil columns. XBGPR modeling was accomplished with a three-dimensional numerical forward modeling code and a two-dimensional inversion routine. Spatial variations in apparent dielectric constant (Ka) and attenuation (a) were mapped. Electrical resistivity modeling was accomplished with a three-dimensional numerical forward modeling code and a three-dimensional inversion routine. Spatial changes in electrical resistivity were then mapped. Three different types of defects were simulated, in addition to a defect-free column. The computer simulations suggest that XBGPR tomography and ER tomography might be useful, non-destructive methods for detecting and estimating the extent of defects in deep-mixed soil columns. The results show that small, isolated defects might be difficult to detect, but defects approximately equal to or larger than the sampling interval (for XBGPR) or vertical electrode spacing (for ERT) should be detectable.

Jan 1, 2004

By Tai Luu, Maxim C. Schisler, Yaser Taheri

The Stevens Gateway Project is an expansion of the Stevens Institute campus overlooking the Hudson River in Hoboken, NJ. The plans call for 90,000 ft2 (8360 m2) of new classroom, research, and student life facilities in new, 4-story buildings. The excavations for the building footprints were bounded by city streets and existing buildings, including the historic Carnegie Laboratory of Engineering, built in 1902. Pit underpinning was originally specified for the Carnegie building. However, given the depth of cut, construction time required for the 13 ft (4.9 m) deep pits would be substantial. The geotechnical contractor retained for the support of excavation work therefore offered an innovative active soil nail wall design that would meet project requirements in a shorter timeframe. Unlike the passive soil nail systems common in the industry that are chiefly used for soil slope stabilization, active soil nail walls contain pre-stressed anchor components to resist soil movement and limit settlement of soil and structures being contained. In addition to a discussion of the overall design approach of the active soil nail wall system, this paper will include a detailed description of its constructability and effectiveness. This project’s use of a conventional slope stabilization technique for an unconventional purpose may have positive implications going forward. INTRODUCTION Stevens Institute of Technology is a private university in Hoboken, New Jersey that sits on the cliffs of the City of Hoboken overlooking the Hudson River and Manhattan Island to the east of the campus. In recent years, the university has executed numerous plans to expand and upgrade its campus academic, student life, and residential facilities. One such project is the Academic Gateway Complex. The plan adds 90,000 ft2 (8360 m2) of new classroom, research, and residential facilities while also enhancing community connections by building a park to serve as a green corridor for the city. The proposed construction took place on the north and south side of 6th Street between Hudson Street and River Street. The project included the demolition of an existing university building followed by the construction of two, 4-story buildings on the north and south property lots. The north and south buildings will be connected by a second floor bridge spanning 6th Street. The buildings each contain a full basement extending from the proposed ground floor at approximately El. 41ft (12.5 m) to the basement subgrade at El. 26 ft (7.9 m). Each building will be constructed on respective mat foundations. Figure 1 presents an overview of the project area.

Jan 1, 2019

By O. Craciun, C. A. Bridges, M. Cai, J. Sugawara

There are a number of methods that can be adopted for predicting the ultimate lateral resistance of a free-head rigid pile, from the conventional Brinch Hansen and Broms solutions to three-dimensional finite element analyses. Often these methods give rise to significantly different pile ultimate lateral capacities which could lead to either unsafe or too conservative designs. It is also well known that finding a rigorous and practical solution is challenging due to the complex three dimensional and nonlinear soil-structure interaction. This paper reviews some of the most common methods and produces results of pile ultimate lateral capacities embedded in cohesive or cohesionless soils. Subsequently, a finite element analysis is performed using PLAXIS 3D modelling under the same design conditions. Based on comparison of results, limitations and advantages are highlighted, and the most suitable method is proposed from a practical point of view.

Nov 1, 2022

By A. Rod Kern, Michael A. McNicholas, Yaser Taheri

Deep foundations were required for construction of an 18,000 ft2 (1,672 m2) 4-story office building and an adjacent 23,750 ft2 (2,206 m2) 5-story parking garage in Queens, New York due to an existing uncontrolled fill layer ranging from 15-20 ft (4.6 - 6.1 m) in thickness beneath the building footprint. The geotechnical engineers for the project initially selected auger cast-in-place (ACIP) piles over driven piles to limit the impact of noise and vibrations on the surrounding neighborhood. Ultimately, drilled displacement piles (DDP) were installed since this method offered a more economical solution that would generate the required pile capacity with shorter drill depths and would also mitigate spoils volume. During installation of test piles by the geotechnical contractor retained for the foundation work, multiple unanticipated soil conditions were encountered that would adversely affect the constructability of the piles. The existing fill contained significantly more natural and manmade obstructions than expected and the underlying glacial soil became too dense to penetrate at shallower depths than anticipated. This paper discusses how these issues were overcome through pre-drilling and the use of detailed instrumented test pile data coupled with in-house engineering capability to proactively re-evaluate minimum pile lengths at any given location and keep the project on track. INTRODUCTION Geotechnical work in the New York City market presents soil conditions that can be highly variable and challenging due to the presence of uncontrolled urban fill placed over the native soils. Construction in this area can therefore pose many unforeseen challenges, even with detailed geotechnical analysis being performed at project sites. A case in point is a construction site in Queens, New York. The proposed site development consisted of construction of a 4-story office building with a footprint of 18,000 ft2 (1672 m2) and a stand-alone 5-level parking garage with a footprint of 23,750 ft2 (2206 m2), together with associated new pavements and utilities. The site is bordered by a mix of commercial buildings and residential properties on all sides. Depth of the uncontrolled nature of the fill extended up to 20 ft (6.1 m) below street grade. Given the significant cost associated with removal and replacement, deep foundations were recommended to bypass the unsuitable soils and support the structures at depth where good bearing material existed.

Jan 1, 2019

By Ke Yang

"Drilled shafts are typically used to support structures subjected to large moments at the shaft head. The large moment can produce push and pull forces on the two sides of a drilled shaft. Consequently, the applied moment is partially resisted by the push-pull moment resistance induced from the vertical side shears. This type of push-pull resistance has not been fully recognized in most design and analysis methods. In this paper, a 30 finite element model for a drilled shaft subjected to lateral load and moment is presented and is validated against two field lateral load tests. Based on the 30 finite element model, a parametric study is carried out. It shows that the push-pull moment can resist 18-35% of the applied moment. The parametric study also shows that the push-pull resistance varies linearly with loading eccentricity when the eccentricity is less than the shaft embedment length. A method to estimate the push-pull resistance is proposed based on the results of the parametric study. Then, a new method for lateral capacity prediction is proposed to account for the push-pull resistance. The base shear resistance is significant for short drilled shafts; therefore it is also included in the proposed method. A case study on four lateral load field tests illustrates that the new method could improve the accuracy of lateral capacity prediction when compared with the traditional Broms method.INTRODUCTIONDrilled shafts are typically used to support a variety of structures subjected to large moments. Sound walls, highway signs, traffic signals, high-rise buildings, electrical transmission towers, and bridge piers are examples of cases where lateral loads with large eccentricity would result in high overturning moments on foundations.Current analysis methods for capacity predictions (Broms, 1964a and 1964b; Brinch Hansen, 1961) or deflection predictions (Reese, et al. 197 4) of laterally loaded drilled shafts are based on the lateral resistance of soils and rocks. However, O'Neill pointed out that moments can be partially resisted through the push-pull resistance provided by the vertical side shears due to the rotation of the pile (Reese, 1997)."

Jan 1, 2005

By James M. Tantalla, Dwight Metcalf, Roderic A. Ellman Jr.

"The construction of a new low head hydro-electric plant at the Cannelton Lock and Dam required the design and construction of a cofferdam to accommodate a deep excavation extending approximately 150 feet below the Ohio River levels. The new plant, which generates about 390 GWh of electricity annually, is owned by American Municipal Power (AMP). A specialist team was assembled to design and construct the cofferdam, marine dike and CB slurry wall that helped make the project successful and on time for project delivery.Because the new plant diverts water from the locks and dam through a powerhouse to generate power, it would need to be partially in the river to operate properly. To accomplish this, approximately 250,000 square feet of land was reclaimed from the river by construction of a marine dike. The dike, combined with the design and construction of a 150 foot deep cement bentonite (CB) cutoff wall enabled construction of the new plant in the dry. Extensive dewatering analyses were performed using Modflow to evaluate pumping requirements and the number of wells needed to maintain ground water at required levels within the side slopes and final subgrade. A monitoring program consisting of inclinometers, piezometers and movement monitoring points were used to monitor cofferdam stability and performance throughout construction. Detailed two and three dimensional stability analyses that included a parametric study of fluctuating river levels and slurry unit weight were performed to ensure stability and suitable low permeability of the trench during cut-off wall excavation both on land and in the marine dike. The wall was constructed with both a hydromill excavating primary panels and a clamshell following behind to construct secondary panels. Data acquisition systems onboard the excavating equipment allowed for detailed confirmation of the continuity of the wall at each interface between panels. Another challenging aspect was the CB mix design for the trench. The cofferdam required the construction of a 1,300-foot long marine dike downstream of the existing dam up to 100 feet tall founded on existing river sediment to enclose the site and cut-off the seepage into the excavation from the river. Marine dike construction utilized vibro-compaction to pre-densify granular fills placed underwater through which the CB trench extended."

Jan 1, 2016

By J. Matos e Silva

The paper refers two examples of structures located in seismic areas (Cases 1 and 2). The first one (Case 1) is the Torroal Bridge, located about 100 Km South of Lisbon, in the road Troia-Grandola. The horizontal loads due to the seismic actions were mainly carried by an anchor curtain connected, to the abutments, by reinforced concrete struts-ties. For the some purpose diaphragm walls were also placed under the pile caps of the column foundations. The second one (Case 2) refers to a building located about 50 Km South of Lisbon, at Sesimbra, near a cliff. To reduce the horizontal displacements of the structure due to seismic actions, in order to prevent the endangering of the cliff stability, an anchor curtain was adopted and connected, to the structure, by prestressed anchors.

Jan 1, 1996

By Lynn Crayne

We used Glyoxal as the hardener, at a final concentration of 10% by volume and therefore 20% by volume in the A-Component. They worked pretty well what we did was we shaved the joints on each of the pipes when we assembled them so they wouldn't rip the packers and then we greased the packers very well going in. We had to replace some but we have any getting stuck or didn't lose any pipes.

Feb 10, 2003

By R. Lee Wooten, David R. Shields, Darren D. Clark

"Borehole permeability tests that measure flow or head changes in boreholes located within seepage barrier walls are commonly used to estimate the in situ permeabilities of those walls for quality control and assurance. The current state of practice for estimating permeabilities from these barrier wall borehole tests is to use equations published by M. J. Hvorslev in 1951. Hvorslev’s borehole test equations model an infinite stratum of uniform permeability, which is not the actual condition for a test performed in a low permeability barrier wall located within a high permeability stratum. We examine and develop alternative equations based on line source analytical models, which more closely match barrier wall test conditions. We describe how these alternate equations can be used to estimate barrier wall permeabilities from borehole tests and compare the results to those obtained from the Hvorslev models. We also provide recommendations that consider differing upstream and downstream water levels.Barrier Wall Permeability Tests - State Of PracticeThe installation of seepage barrier walls has become more common in a variety of applications ranging from dams and levees to contaminated sites requiring retardation of groundwater flow. The types of seepage barrier walls and installation methods include soil-bentonite, soil-cement-bentonite, concrete, self-hardening slurry, geomembranes, and sheet piles, installed with various soil mixing, slurry-supported trench, and driving methods.Owners and contractors have used a variety of methods to evaluate the permeability of these seepage barriers. The following table lists commonly used quality control/assurance tests for evaluating the permeability of a seepage barrier."

Jan 1, 2016

By Gisele R. Passalacqua, Aly Mohammad, Joanna Smith

The $13 billion John F. Kennedy (JFK) airport construction redevelopment program includes new terminals and buildings that are supported on piles to meet the airport expansion demand due to increased travel. This paper presents a case history for JFK airport with main focus on construction activities and lessons learned. Challenges include limited head room, presence of underground utilities, and hard driving. Video inspection of pile proved very beneficial. In general, soil conditions at JFK Airport consists of sandy fill followed by a 5-foot thick organic soft layer. Below the organic layer, glacial sands occasionally mixed with gravel were encountered for great depth with increases in density with depth. The tapertube pile is an ideal choice for foundations with high capacity achieved through skin friction along the taper section. The piles are easy to splice to accommodate low head room. Pile Driving Analyzers (PDA), and Static Compression Load Tests were performed. The results of these tests are presented in this paper to illustrate the high pile capacity achieved. More detailed discussion and analysis of the test results will be presented in another paper related to the same project. Lessons learned from this project are shared to help the engineering community with future design and construction of similar projects.

By Hugo Meggitt, Damian R. Siebert, Wystan Carswell

Excavation-induced ground movements are a critical component in the design and construction of deep excavations in urban settings due to the potential adverse effects on adjacent structures and infrastructure. Ground movements are influenced by soil stratigraphy, soil properties, adjacent structures, and construction means and methods. The use of empirical relationships, computer models, and reliance on experience with similar excavations in similar soil conditions often provides a basis for predicting excavation-induced ground movements. In this paper, data from 21 deep excavations approximately 20 ft to 75 ft deep supported by concrete diaphragm “slurry” walls in the Greater Boston area are compared to published literature, considering how different foundation systems (e.g. shallow foundations, caissons, and piles) of abutting structures have been affected by adjacent excavations. The influence of construction method (conventional vs. top-down) on adjacent foundation movements indicate that top-down construction typically results in smaller foundation movements. INTRODUCTION Estimation of ground movements due to excavation is a challenging endeavor, even with complex three- dimensional finite element modeling and high-order constitutive models that are increasingly available in modern engineering practice. Aside from the expense of the soil exploration and testing used to inform these higher-order models, the challenges of modeling past stress history, adjacent structures, and the groundwater conditions during excavation require not only large investments of time during design but also validation from past experience (to avoid a “garbage in, garbage out” paradigm). While site conditions such as soil stratigraphy, soil properties, groundwater conditions, and as-built conditions of adjacent structures can be obtained, measured, and estimated, the effects that means and methods of construction have on ground movements are difficult to quantify. During early phase design, assessments of predicted ground movement are unable to account for all aspects of project construction, nor is it cost-efficient to fully design an excavation while project parameters such as site size and excavation depth are under consideration by the design team. While construction is in progress, benchmarking support of excavation performance and associated ground movements in the context of successfully completed projects allows for a more nuanced view of system performance and provides the opportunity for more informed decision-making (if required) as construction proceeds. For these reasons, the use of empirical relationships and the collection of historical support of excavation performance holds high value for the practicing geotechnical engineer at all phases of the project.

Jan 1, 2019

By Eric C. Halpin

"1. Introduction and Backgrounda. In its fundamental form, risk is simply the likelihood of an adverse impact. Expanding on this theme, the Corps of Engineers has broadly defined risk associated with infrastructure as a factor of three distinct elements: a probabilistic assessment of a hazard such as a flood or earthquake; a probabilistic assessment of how the infrastructure performs in the face of this hazard; and a measure of the likely consequences – loss of life, economic damage, environmental impacts – associated with the resulting inundation scenarios.b. The lessons and observations described herein relate to the Corps of Engineers experiences in implementing risk concepts for infrastructure management during the period 2005 through 2013. The Corps of Engineers is a large, decentrally operated and centrally led federal agency that plans, designs, constructs, operates, maintains, and/or manages a portfolio of over 3,000 built dam and levee systems within the United States. The infrastructure in this portfolio is 55 years old on average, and although much of the structures provide for flood risk management benefits, many of the dams deliver multi-purpose benefits. Scale matters – where scale and uncertainty are large, risk concepts provide great opportunity and arrangement for application.c. The amount of organizational change that is demanded for the implementation of risk concepts is considerable and should not be under estimated, but need not be feared if the path others have taken is considered. This paper is, in many ways, an opportunity to step back from the last seven years of implementing risk informed management, check our own azimuth and maturation, and share the purpose and energy behind our own continuing actions. Hopefully, this azimuth check is also beneficial to those that are either considering the use of risk or are in the process of implementing risk concepts.d. Success at managing the massive change related to incorporation of risk concepts will directly affect success of the infrastructure program. The three key organizational elements to consider –human systems such as governance and competencies; policies that outline the who, when, and why of decisions and management; and the processes and technology that outline how work is to be performed - are changed fundamentally. From senior leaders to project team members and all of the people in between, there is a need to discuss, confront, and vet the change and the role people and organizations have in the process. For the Corps of Engineers, with a history of over two centuries, deeply embedded beliefs about infrastructure aren’t transformed over night - the change process is decadal in scope. Given our self imposed “project execution” mantra and corporate objective, risk seemed threatening at first to the cost and schedule of delivering infrastructure projects. In reality, risk concepts have been responsible for savings and cost avoidance of nearly $6 billion over the last three years alone while at the same time justifying increased investment by several fold for the highest risk needs."

Jan 1, 2014

By M. A. El-Sohby

The paper describes some problems encountered with the foundation of a deep drainage caisson constructed on the Nile Bank in Cairo. The use of suction dredging while sinking the caisson led to a piping failure of the sandy soil in the base which was loosened during the process of pumping. A study was carried out to investigate the problem and a procedure was adopted to retain the stability of the caisson.

Jan 1, 2010

By Evelio N. Horta

The influence of soil improvement replacement area in foundation settlements is discussed for soil improvement methods used in Southeast Florida. A 3D Finite element analysis is used for two typical conditions in the area: foundations bearing on loose sands and foundations bearing on a crust of limestone underlaid by very loose sands. Particular attention is given to Jet Grouting as a soil improvement method. The potential impact of the stiffer jet grout columns on the structural foundation design and quality control issues are also discussed. It is shown that in loose sand conditions 15 to 20% area replacement produces substantial reduction in total settlements. Reduction in total settlements for mixed profile is less significant but the use of the method in those cases is directed to reduce punch through potential.

Jan 1, 2007

By M. Cornelius

Drilled shaft construction through caving soils has historically been an uncertain, risky and costly operation. Uncertain, because the zone of caving may or may not be known, risky because the loss of a shaft is disastrous, and costly because the Contractor, who faces these risks, must include large sums of money in his bid for shaft wall stabilization techniques. This case study will discuss the stabilization techniques that are typically used within the United States, and then present new technologies, born in Europe, that are being utilized in the States by Malcolm Drilling Company today.

Jan 1, 1999