Search Documents

Jan 1, 1988

Jan 1, 2005

By Moi Arzamendi, Jose Ramirez, Kenneth Kniss, Sunil Arora, James Gingery

Construction of a new approach embankment for a railroad bridge over a river in Southern California required placing up to 12 ft of fill over soft to medium stiff silts and clays along an approximate 1,500-ft long stretch. The embankment, situated within a narrow railroad right-of-way between an existing live track and existing buildings, would have been susceptible to excessive settlement that could damage existing buildings and numerous underground utilities if regular weight soil fill had been placed over the unimproved ground. To limit total and differential static settlements to tolerable levels, a design was developed using a combination of mechanically stabilized earth wall with lightweight cellular concrete fill and rigid inclusions ground improvement. This paper describes the design of the ground improvement system, construction methods used, and challenges of working next to live railroad traffic. Ground improvement quality control and assurance measures, and verification of performance by settlement monitoring are also addressed. INTRODUCTION AND BACKGROUND The 0.9-mile San Diego River Double Track (SDRDT) project is located on the Los Angeles-San Diego- San Luis Obispo (LOSSAN) Corridor in San Diego, California. The project includes the replacement of the existing 900-ft long single track railroad bridge over the San Diego River with twin double track structures. Construction of the project is phased and closely coordinated with the associated Mid-Coast light rail project (San Diego Trolley Blue Line Extension). The new bridge is a 7-span, twin steel, through girder structure supported by six cast-in-place reinforced concrete pier caps and two abutments. The large diameter cast-in-drilled-hole (CIDH) foundations are up to 9 ft in diameter, with upper portions encased in a 1.5-in.-thick permanent steel casing. The north abutment approach embankment includes a mechanically stabilized earth (MSE) retaining wall up to approximately 10 ft high and 1,520 ft long. This paper focuses on the design and construction of the north approach embankment. The project site is characterized by challenging geotechnical and seismic conditions. The site contains liquefiable soils interbedded with soft cohesive soils, underlain by competent layers of sand/gravel/cobble and other sedimentary formations. Static settlement of the new railroad, crossing utilities and adjacent buildings was a primary design concern for the north approach embankment.

Jan 1, 2018

By Peter J. Nicholson

The methods of reinforcement to be discussed in this paper are all insitu methods, ones that can be used on the soil structure as it exists in the ground, and do not rely on excavation and replacement of the soil. Current practice in the United States, as well as new ideas and methods, will be discussed as they relate to slope stability, retaining walls, and to other uses such as control of mine or cavity related subsidence and to liquefaction control under existing structures. The method is based on the concept of "nailing" or reinforcing the soil in place, and thereby causing a mass of soil to act as a coherent unit. When performed properly, a true gravity structure can be constructed, one that will remain intact under both horizontal and vertical loadings and that will also resist vibrational and seismic loadings.

Jan 1, 1991

By Joel B. Dellaria, Justin R. Lewis

"No. 9 Walton is a new high-rise condominium building located in the Gold Coast area of Chicago. The adjacent building, Walton on the Park, featured 4 levels of below grade parking and utilized a secant pile wall with integral drilled shafts to support the exterior columns. The earth retention system (ERS) for No. 9 Walton also employed a secant pile wall in combination with drilled shafts. The excavation into the soft Chicago clays varied in depth from 9.75 m to 12.5 m (32 feet to 41 feet) below grade. The temporary excavation support used internal braces from the new secant piles to the existing foundation system of Walton on the Park to provide earth retention. Engineering teams for both projects worked together to design the bracing scheme and connections to ensure that the new excavation and internal bracing would not overstress any elements of the existing structure. Further complicating the project, immediately to the west of the project was a historic church founded on shallow spread footings which required underpinning to minimize movements.The project involved three different building owners, small values for acceptable wall movement, an extensive monitoring program and the challenges of merging two earth retention systems. The subsurface conditions at the site, the adjacent structures, the excavation, and the performance are described. A summary of the design methods and the expected movements of the ERS are discussed, and the performance monitoring system is described. Overall, the ERS performed better than expected with less than 1 inch of measured lateral wall movement during and after the excavation was completed. Measured performance of the ERS is compared to the predicted performance and to the performance requirements for the project.INTRODUCTIONNo. 9 Walton is a new high-rise condominium building in Chicago located in the Gold Coast. The building has 3 levels of below grade parking and 36 levels of living space above grade. Developers originally slated the project to be Phase 2 of the Walton on the Park development built in the mid 2000’s, using portions of the existing foundation system for development of the new structure. However, the housing market crash in 2007 prompted cancellation of Phase 2 of the Walton on the Park development. The property sat undeveloped until 2015 when design and construction for No. 9 Walton began under a new development and design team. The project team completed foundation excavation and below grade structures in 2016 with the first units of the building turned over to new homeowners in 2017.The structural design for No. 9 Walton consisted of reinforced concrete columns and slabs, supported laterally by a heavily reinforced concrete central core. Drilled shafts to rock supported the interior columns and core with the exterior columns and foundations integrally included in the earth retention system. The structure had a below-grade footprint of approximately 1,490 m2 (16,000 ft2). The general excavation extended 9.75 m to 12.5 m (32 feet to 41 feet) below street level with the deepest portions at the central building core mat foundation."

Jan 1, 2017

By Armin W. Stuedlein, Seth C. Reddy

In this study, factors affecting the reliability of augered cast-in-place (ACIP) piles under axial compression at the serviceability limit state are addressed using a simple probabilistic hyperbolic model and a database of load tests on ACIP piles in cohesion less soils. The aleatory and model uncertainty in a selected load-displacement model is statistically characterized, and is used to simulate representative random samples from the bivariate random vector of model parameters. A first-order reliability method (FORM) was used to determine the effect of sample size on the stability and uncertainty of the reliability index. Sample sizes greater than about 40 provided relatively consistent estimates of the reliability index; however, its uncertainty continued to decrease with increasing sample sizes. Additionally, the effect of slenderness ratio on the reliability of the serviceability limit state design was characterized and found to exhibit a significant effect on the probability of exceeding a specified displacement.

Jan 1, 2013

By Neil T. Russo, Peter M. Kandaris, Jogi S. Gadok

"Assessment of subsurface data for foundation design in support of long high voltage electric transmission lines is best accomplished using a probabilistic strategy since only a small portion of structure locations are typically sampled. Probabilistic approaches provide a tool to evaluate site uncertainty in a systematic and rational manner. This paper provides a case history of a risk-based design approach for a recently completed 191-mile long 69/161/345kV steel monopole transmission line traversing Central Iowa. The project owner made available limited subsurface information at project initiation, requiring the design team to obtain additional data within a constrained budget for 1067 large diameter, laterally-loaded deep drilled shaft reinforced concrete piers. The team commissioned a geologic desktop study to reduce uncertainty in subsurface evaluations and aid in selecting additional sample sites. In total, investigation programs tested approximately 15 percent of structure sites. The paper details the probabilistic approach used to estimate foundation geotechnical design parameters, with information from the various studies categorizing strata both laterally and with depth. Low-bound parameters were estimated via a statistical approach at a predetermined reliability level. Significant savings resulted from this approach when compared to conservative deterministic processes. Project QA/QC logged subsurface soil conditions during foundation excavation, then compared as-found conditions to the conditions assumed for design. The team redesigned foundations if either a non-conservative variance in soil conditions was observed or if bedrock elevation differed significantly from design assumptions. As a result, only 22 out of 1067 foundations required modification during construction (2% variance from initial design) with negligible impact on the construction budget and schedule.INTRODUCTIONFoundation design for long high voltage transmission lines presents a unique challenge in that the assessment of subsurface conditions typically requires substantial data that may or may not be obtainable. Investigations are usually performed well in advance of construction, often with limited access to structure sites and typically in remote areas. Probability and risk-based investigation and design strategies offer an opportunity to systematically estimate subsurface profiles and geotechnical design properties with limited data. Risk can be further reduced with dedicated field inspection of foundation construction along with good field and design team communication during construction. This paper presents a case history of probabilistic methods used for the investigation and design of electric transmission line foundations."

Jan 1, 2017

By Gerry Houlahan

"The 2015 Outstanding Project Award (OPA), which recognizes the superior work of DFI members, was awarded for the San Francisco- Oakland Bay Bridge New East Span. The award was presented to representatives from Caltrans and the T.Y. Lin International/Moffatt & Nichol Joint Venture at the DFI 40th Annual Conference on Deep Foundations in Oakland, Calif. A committee selected this project based on size, scope and challenges of the project; degree of innovation and ingenuity exercised; and the uniqueness of the solution to the difficulties of the job. A bridge across the bay between San Francisco and Oakland was proposed as early as 1872, but it took until November 12, 1936, until it became a reality. The bridge spans to the west of Yerba Buena Island were conventional suspension spans, while the east spans used a steel cantilever truss design and simple steel truss spans. This double-deck bridge served the Bay Area well until 1989. In that year, the magnitude 7.1 Loma Prieta earthquake damaged the East Span of the San Francisco-Oakland Bay Bridge. The resulting interruption to service across the bay demonstrated the vital role this bridge plays in the economic and life safety activities of the Bay Area. The project owner, California Department of Transportation (Caltrans), determined that the safest, most cost-effective solution was a total bridge replacement. The Engineer-of-Record, T.Y. Lin International/ Moffatt & Nichol Joint Venture, working closely with Caltrans, the Metropolitan Transportation Commission (MTC) and the California Transportation Commission (CTC), was charged with developing a comprehensive design strategy that met the project’s stringent criteria for seismic safety. These criteria included the new bridge’s designation as a regional Lifeline Structure that must open to emergency traffic shortly after the occurrence of a 1,500-year return period earthquake"

Jan 1, 2015

[ENGLISH active earth pressure adapter additive adhesion admixture, addition adsorbed water aggregate air air entrainment air hose allowable bearing value allowable pile bearing load]

Jan 1, 1994

By Derrick Dasenbrock, Mary C. Nodine, Benjamin Rivers

Up to 50 percent of major infrastructure projects suffer impacts to schedule or cost due to geotechnical issues, many of which correspond to risks related directly or indirectly to the scope and quality of site characterization work. The Federal Highway Administration (FHWA) in coordination with industry organizations seeks to address this issue through Every Day Counts (EDC), a program that identifies and deploys proven, yet underutilized innovations at the project level to save time, money and resources. The A-GaME (Advanced Geotechnical Methods in Exploration) is one of the innovations supported under EDC.

By Kul Bhushan

This paper presents the results of lateral load tests on 0.61-m to 1.27-m (24 to 50-inch) diameter drilled and cast-in-place piers in San Diego area residual/formational soils. The test piers were installed and tested in the following soils: Decomposed Granitic Rock (Ktd), Stadium Conglomerate (Tst), and Friars Formation (Tf). Lateral loads of up to 845 KN (190 kip) were applied to the piers in residual granitic soils, and loads up to 1780 KN (400 kip) were applied to the piers in Stadium Conglomerate and Friars Formation. The tests were conducted by jacking against adjacent piers and monitoring the lateral load and lateral deflection at the ground line. Test results indicate that ultimate lateral pile capacities of up to 1800 KN (400 kip) can be obtained for 0.61 m (24-inch) drilled piers with penetration of 3 to 6 m (10 to 20 ft) in the residual/formational soils tested. Lateral load analyses using p-y curves for very dense sand significantly overestimate the observed lateral deflections. For lateral load analyses using dense sand p-y curves, p-multipliers that increase the lateral soil stiffness (p-y curves) by 2 to 8 times are required to match the load-deflection behavior measured in the test piles. When applied to the dense sand p-y curves, the p-multipliers provide a more accurate prediction of load-deflection behavior in the residual/formational soils, and can result in shorter required pier penetration and significant savings in foundation cost.

Jan 1, 2002

By Allan Sylvester

This paper will discuss the design, construction, and performance of the support of excavation on the San Diego State University LRT Station. The vertical elements of the system include drilled secant piles and drilled soldier piles. We will discuss the geo-technical characteristics, design and construction considerations, loading criteria, construction techniques, schedule constraints, and performance of the pile and support of excavation systems. In consideration of the conference theme, there will be a discussion of the successful accomplishment of meeting the interim milestone dates of the Contract. The project team cooperatively worked to design and install approximately 1,100 drilled secant and soldier piles as well as excavate and install the balance of the support of excavation elements in such a manner as to minimize the disruption to campus students and operations.

Jan 1, 2002

By George Filz, Peter R. Cali

"Unnecessarily restrictive specifications could be limiting the cost effectiveness of deep mixing (DM) applications and therefore limiting use of DM on projects where there are other options. Excessively restrictive standards demanded for strength and permeability certainly increase contractors’ bid prices, and costing the owners and, in the case of Government projects, the taxpayers more than necessary. Yet, lax or ineffective specifications often exist for some vital components of the quality assurance and quality control. In this paper, specifications for key elements of DM design and construction are examined. Recommendations are made to improve and streamline DM specifications to better serve the common objective of constructing a safe and cost effective ground improvement project.INTRODUCTIONSpecifications should, at their best, convey the project design requirements and provide clear direction to the contractor regarding requirements for submittals, materials, execution, measurement, schedule, and other aspects as necessary. The specifications should not be overly conservative, restrictive or ambiguous, and they absolutely should not be deficient in measurement of quality. Guide specifications or recycled sections from previous projects often form the template for new project specifications. But standards that appear in guide specifications or from former successful construction should be critically scrutinized by the designer for relevance before using the copy/paste functions of the specifications writer’s keyboard. Because work does not always go as smoothly as planned, specifications for remediation of non-compliant construction should be clearly stated and enforced. Often, non-compliancy is reviewed after-the-fact and deemed to have met the design intent, indicating that either the specifications were too restrictive or the enforcement too weak.The Federal Highway Administration Design Manual: Deep Mixing for Embankment and Foundation Support, October 2013, was written by a panel of DM expert design practitioners and contractors. Guide specifications are included as Appendix C of the FHWA manual. Those guide specifications have been updated in the deep mixing section of the www.GeoTechTools.org website, and the updated specifications represent the most complete and authoritative compilation published to date. Although the specifications for DM at www.GeoTechTools.org are current and complete, and they portray the state-ofthe- practice, they too must be modified to fit specific DM applications, project needs, and site conditions. The keys to a good set of specifications are to prescribe construction only to the level that is required to meet the design intent, to require appropriate quality control and quality assurance (QC/ QA) activities, and to clearly address remedial measures required for non-compliant work."

Jan 1, 2015

Jan 1, 1989

Jan 1, 2004

By Christian Hoyme, Jochen Maurer

Most of the current foundation projects are suffering from disconnected information silos. In the first silo there is the planning of the project with corresponding data, presented by paper or digital drawings. Here will Building Information Modeling (BIM) be one of the trends for the future. We will see more and more projects leaving the “old way” of 2D drawings and moving into 3D planning including metadata of the foundations. But even with a perfect BIM model of a jobsite, we are not at final end of digitalization. While execution of the project at the jobsite, a second data silo is evolving. Data collected directly from construction equipment and manual measurements is currently undervalued in most projects. Paper is passed to the equipment operator and major data from measurements on site are noted on paper and digitized afterwards. Automatically collected data is not be used to create site progress reports or similar report. So, the real “data” just flows around without connection to any other data already existing in projects. And then the third silo arises: The documentation of the project. Data collected on paper es reentered to create some basic documentation of the work handed over to the client. Spreadsheet software is still the “tool-to-be-used” to create at least some documentation. Finally, the documentation is not connected to the data created while planning and not connected to the automatically collected data from the jobsite. A connected jobsite in the foundation industry must link these information silos and have to create a full data-workflow from the design through the execution to the as-built documentation. INTRODUCTION Building information modelling (BIM) is currently the most popular term of construction business in Germany and probably all over the world. But as often there are many different definitions out there and everyone has his own definition or at least understanding what BIM is about. But for sure it is the most relevant for the construction industry in the near future. Most popular is the digital twin for the upper structure of a building. In most cases the BIM models just shows the building itself, but there is more to be implemented. For example: projects where a special foundation is needed, BIM should include also the foundation elements with meta data. There are several advantages. Not only the clash detection of anchors, but also the possibilities to check the interaction with neighbor constructions, power lines and so on are a use case. For sure most of the special foundation elements are not relevant for the whole lifecycle of a building. But during construction and later the demolition the information about the hidden elements is important and gives a benefit to all stakeholders. In the future there will be not the question: “What is already in the ground?”. The risk for following construction projects on the same ground will be minimized.

Jan 1, 2019

By Giovanni A. Bonita, Asher H. Peltz, Sean D. Johnson

This paper examines a complex earthwork project in the Washington DC metro area that had project delivery directly impacted by questionable instrumentation monitoring data. The case study summarizes the impacts to the project caused by questionable instrumentation data and reveals how the authors were able to utilize data to extract meaningful insights. The case study also demonstrates how clear data presentation became a key factor in maintaining stakeholder trust and facilitated progress of the project schedule. The case study highlights key points to collecting high quality instrumentation data, approaches to assess and improve value of the data collected, and techniques to reduce and interpret questionable data.

This manual provides basic practical instruction on the inspection of driven piles. It covers the essential components of pile driving, such as the pile driving hammer, hammer accessories, the pile and soil, and frequently encountered test methods in an uncomplicated, yet knowledgeable, and practical manner. Insight is given into the methods of installing the foundation, dealing with the cranes which do the lifting, the hammers which do the driving, the leads that guide the hammer and pile, the compressors which provide the external power when required, and finally prevalent analysis tools and testing instrumentation and procedures which enable you, the Inspector, to do your job. This DFI Inspector's Manual for Pile Foundations will help the Pile Inspector who has limited knowledge of pile foundations. Perhaps this Inspector has been pressed into service at a moments notice; a few helpful hints and suggestions to him are desperately needed and he can look here for the basics. It is also useful for the experienced Pile Inspector as a reference guide. However, this manual is not a detailed check list of every possible scenario and detail which could ever be encountered. There are other sources available which give more detailed descriptions (and should be consulted by the Inspector when appropriate; a list of this additional reference material is provided and suggestions made in appropriate chapters of this text). The current manual is more a brief "textbook overview" with some of the more important aspects given at least some emphasis so that the Inspector has some direction and hopefully helps to produce a safe, yet economical, foundation.

Jan 1, 1997

"TREVIICOS CorporationINTRODUCTIONThe Walter F. George lock and dam was constructed on the Chattahoochee River between 1955 and 1963 with the double function of improving navigation and generating power. Its 82 ft. by 450 ft. (25m x 137m) lock can accommodate large barge traffic and its four generating units with a plant capacity of 150 MW have an average energy output of 453,000 MWH. The dam consists of a 1,496 ft. (456m) long concrete structure housing the spillway, a non overflow portion, the power units and two earthen wing dams extending to the Georgia and Alabama sides, respectively 5,810 feet and 6,130 feet long (1770m and 1868m). As soon as the reservoir was impounded it became apparent that excessive seepage was occurring. From 1962 to 1985 a series of remedial works was performed using several techniques, but the problems continued under the dam, jeopardizing its generating potential and possibly undermining its stability.Finally, the decision was made to construct a deep cutoff primarily under the concrete portion of the dam to remedy the problem. PROCUREMENTOn July 5th, 2001 best and final offers were solicited by the Corps of Engineers (COE) for the construction of a deep cut-off to be built in front of the concrete portion of the dam from the bottom of the lake and tied into it. The cut-off had to cross an existing lock structure and an underwater retaining wall, as well as the remnants of a steel coffer cell left in place from the initial construction.The specifications required that the wall be built with a minimum thickness of 24” (600mm) and that it extended from the bottom of the lake to elevation -5 (1.52m) into the Providence formation, an impervious layer.While the land portions of the wall were on average 208 feet (63.4m) deep, the marine portion started from up to 90 feet (27m) of water and continued through different rock formations for another 100 feet (30m).Contractors were invited to propose their own method of constructing the cut-off and offers would be evaluated using several criteria, including technical, economical, organizational and experience.Three proposals were received and on August 14, 2001 an award was made to the Joint Venture (JV) of Treviicos and Rodio."

Jan 1, 2014

Jan 1, 1984