Search Documents

By Gene Bryant, Wesley Schmutzler, Matteo Bertoni

The levees where the Mississippi River and the Lower Wood River meet near East Alton Illinois have been a problem area for years due to underseepage. The first phase of the deep cutoff wall was a 2,000-linear foot section that was completed in 2016 for the Illinois Flood Prevention District Council. This section was installed along the Wood River and the Mississippi river to depths of over 135’, The United States Army Corps of Engineers was tasked with continuing the cutoff wall along the Mississippi river. The wall was a continuation of phase I with depths up to 140’. The 1,000’ long cutoff wall was installed through fill, loose sands, cobbles, and sandy clay. The cutoff wall was terminated in either Glacial Till or sound rock. In order to provide wall permeability equal to or less than 1.0 X 10-6 cm/sec a self-hardening slurry (SHS) composed of ordinary Portland cement, slag cement, and water was utilized. The depths reached on this project using SHS is the deepest done to date in the United States. Along with the permeability requirements, a very narrow range for the unconfined compressive strength was specified at 50 – 180 PSI. In order to monitor the ground movement and water level fluctuations during the excavation of the panels with the Hydromill or Clamshell, 6 automated inclinometers were installed and monitored continuously during panel excavation in phase 1. Seven automated piezometers were monitored in phase 2. This paper will give an overview of the project with emphasis on the effect of the excavation on the instrumentation, specifically the reaction of the piezometers as the last panels were installed. INTRODUCTION The project is in Illinois, about 1000 feet downstream from where the Wood River Creek enters the Mississippi River between East Alton, IL and Wood River, IL adjacent to State Highway 143 (Fig. 1). The Wood River Lower Cutoff Wall Phase 2 Project (WR2) was awarded to TREVIICOS SOUTH (TIS) in September 2017. The Main Project features are: Construction of work platform, inclinometers installation and removal, cutoff wall construction by the Self-Hardening Slurry method (approx. 135,000 sf) up to 140' depth, clay cap installation, and site restoration. The levee system along this stretch of the Mississippi River has been plagued by under-seepage for several years. The phenomenon has worsened to varying degrees, depending on location, to the point that remediation was needed to ensure that Levee failure would not be an issue in the future.

Jan 1, 2019

By Richard E. Sylwester

Evaluating surface and subsurface conditions for marine foundations (bridges, causeways, terminals, etc.) is often done with a limited amount of data. Subsurface information for these projects is primarily acquired using traditional methods, such as boreholes, test pits or divers, which tend to be expensive and limited in the area of coverage. A number of geophysical methods, including precision bathymetry, sidescan sonar, and seismic reflection or subbottom profiling are extremely cost-effective and obtain significantly more data than can be acquired using traditional intrusive methods. These geophysical methods provide detailed surface images and continuous profiles of the subsurface stratigraphy. This information can be invaluable for selecting the best location for geotechnical boreholes and to map potential geohazards such as submarine slides and filled or open scour holes. Offshore investigations conducted for a proposed highway bridge (Knik Arm Bridge, Cook Inlet, AK), the retrofit of two existing bridge (Antioch and Dumbarton Bridges, CA) and a proposed cruise ship terminal (Ketchikan, AK) used a combination of geophysical methods to map water depth, detect and map debris on the seabed, map the thickness of unconsolidated sediment, determine the depth to bedrock and identify potential geohazards such as scour holes. The results of the geophysical investigations will be used to select locations for obtaining geotechnical borings, to extrapolate geologic information between existing or proposed boreholes, evaluate the potential depth of scour and design a pile support pier. Geotechnical engineers, offshore contractors and bridge designers are realizing the importance of the early use of offshore geophysics for (i) site characterization, (ii) to reduce the uncertainty of geotechnical conditions thus avoiding designs that may be overly conservative and thus more expensive and (iii) to assist in selecting locations for geotechnical borings.

May 11, 2007

By C. Vipulanandan

With the aging infrastructure, there is a need to maintain and extend the service life of steel structures in general and steel piles in particular. Steel piles support not only vertical loads but also dynamic horizontal loads in onshore and offshore applications. In order to select the appropriate methods to repair corroded steel piles used in onshore and offshore application, corrosion mechanisms were investigated with the rate of corrosion in various environments. The corrosion rate of steel in soil, water and soil-water interface varied from 2 to 500 µm/year. Based on literature review and analyses, the repair methods can be broadly characterized as protective coating, electro-chemical methods, wrapping and encasement and partial replacement of steel. Also, methods to evaluate the repair materials and the repair configuration have been documented.

By Colin C. West

On August 7, 1986, Barge 45, while being towed near the mouth of the Niagara River, was swept downstream and pinned against one of the central piers of the Peace Bridge. The barge rested against the pier with 125 feet overlying the Canadian border and 50 feet overlying the American border. The tug boat which was towing the barge was lost further downstream. Fortunately, the crew escaped and were rescued with no loss of life. There was serious concern about the potential erosion effects of the river currents on the foundation of the bridge pier as caused by the flow concentrations around the barge structure. Due to the time of year, with the approaching Fall and associated worsening weather conditions, it was imperative that the barge be removed as soon as possible. Donjon Marine of New Jersey, the United States Navy's Atlantic Zone Contractor, was called on to retrieve the barge. By this time the original owner had abandoned the wreck.

Jan 1, 1987

By Richard J. Finno

This paper presents an overview of methods that can be used to predict damage to buildings as a result of excavation-induced ground movements and describes an adaptive management approach for predicting, monitoring, and controlling excavation-induced ground movements. Successful updating of performance predictions depends equally on reasonable numerical simulations of performance, the type of monitoring data used as observations, and the optimization techniques used to minimize the difference between predictions and observed performance. This paper summarizes each of these factors and emphasizes their inter-dependence. Case studies are presented to illustrate the capabilities of this approach. Examples are given to show how optimized parameters based upon data obtained at early stages of excavation can be used to predict performance at latter stages, and how they can be applied to other excavations in similar geologic conditions.

Jan 1, 2010

By J. S. Lee, R. K. Massarsch

"A 3.2 km long immersed road tunnel forms part of the Busan-Geoje Fixed Link in South Korea, which connects Korea's second largest city Busan, with the island of Geoje. To ensure the water tightness of the joints of the segmental tunnel structure and to limit the forces in the shear keys, the differential settlements have to be limited. This was achieved by extensive soil improvement of the marine clay below the tunnel with cement deep mixing (CDM) and sand compaction piles (SCP). This paper focuses on the characteristics of the marine clay, the basic design principles, layout and constructional issues of the CDM soil improvement, and numerical and numerical analyses to predict settlement and stability.INTRODUCTIONThe Busan-Geoje Fixed Link consists of two short cut & cover tunnel access ramps, a 3.2 km long immersed tunnel (Figure 1) and two long span cable stayed bridges. The tunnel consists of eighteen concrete elements each of 180 m length having a rectangular cross section of 26.5 m in width and 10 m in height. The tunnel elements are cast in a dry dock on shore and floated out to the sea, immersed in their final positions on a gravel bed in pre-excavated trench and connected to each other by a dual gasket system. The water depth was up to 50 m making the tunnel of the deepest yet constructed. After immersion, the tunnel is protected by backfill material at the sides and rock armour on top. Each tunnel element consists of eight 22.5 m long segments. The joints between the segments and between the tunnel elements are equipped with EDPM water stops, Omega seals and concrete shear keys. The longitudinal displacement behaviour of the segmental tunnel structure in the varying ground conditions represents a complex soil-structure interaction problem which has been modelled with a FEM structural model representing the tunnel, the joints and with springs to represent the soil that are derived from the PLAXIS soil/foundation models. In order to ensure the water tightness of the joints which have limited opening capacity and to limit the forces in the shear keys, differential longitudinal settlements have to be limited. This is achieved by limiting the variations in subgrade modulus along the alignment and it in practice means that differential settlements are limited to a few tens of millimetres. Without soil improvement of the marine clay below the tunnel, long-term tunnel settlements of up to 400 mm were predicted when taking into account the likely variations in the trench profile, backfilling and uncertainties in the soil properties. Such large total settlements led to large variations in the sub-grade reaction along the alignment, which in turn resulted in significant differential settlements, unacceptable joint opening and large shear key loading. It was therefore decided to carry out extensive soil improvement with cement deep mixing (CDM) (CDIT, 1999) and sand compaction piles (SCP) (Kitazume, 2005) after studying a number of foundation alternatives."

Jan 1, 2015

By Venkata Krishnaiah Yeddala, Sai Vivek Adari, Suresh Kumar Velugu

Assam cancer care foundation (ACCF) proposed the construction of hospitals and related facilities across 18 locations in the state of Assam-India. Tezpur is one among the 18 locations of Assam with high seismic risk. The strata at the site are comprised of mostly fine silty sands of lower SPT- N values. The water table is also encountered and ranging from 1 m to 2 m below EGL. Since the site lies in seismic zone V as per IS 1893, detailed liquefaction analysis is carried out for all five boreholes and indicates that soil is liquefiable and ground improvement is inevitable up to a depth of 15 m below existing ground level. To mitigate the liquefaction potential and enhance the seismic performance of the soil, ground improvement using stone columns by Wet top feed Vibro-replacement method is proposed. Also, the differential settlements can be avoided effectively under the raft foundation with Vibro Stone Columns. In this paper, field test validation results such as Pre and post-SPTs and ECPTs to access the extent of ground improvement, along with other information adopted in this project presented.

Nov 1, 2022

By D. M. Holloway

As a part of the 1-15 Reconstruction Project, static and dynamic (high-strain) testing methods formed the basis to estimate long-term axial capacities, and to assess the magnitudes of bearing capacity gains (setup) from the end of installation to the time of static/dynamic tests weeks later. This paper summarizes the results of nine full scale pile load tests to failure in compression, and how the designers used these data to finalize pile selection and penetration criteria bridge-by-bridge in the final design stages. Soil conditions along the project alignment ranged from deep, lightly over-consolidated Lake Bonneville clays interbedded with granular strata of varying consistency, to sites dominated by dense alluvial deposits of cohesionless soils well above the water table. The test sites were selected to bracket the conditions that are expected. Twelve-, 16-, and 24-inch-OD pipe piles are to be used to support the new bridges. The team plans to impact-drive all piles closed-end to final penetrations. The test piles varied from 35-ft-long pipes driven to refusal in the shallow dense sands at some sites, to 115-ft-long pipes stopping at 3 blows per foot in predominantly cohesive deposits. The capacities gained with time proved to be reasonably predictable, and significant setup was noted both in the cohesive and cohesionless strata. The test program objectives included providing the means to estimate long-term capacities from short-term (24- to 48-hour) restrikes following installation of foundation piles during production driving operations.

Jan 1, 1998

By H. W. Hunt

Accessories are increasingly used to protect and extend H, pipe, precast concrete, timber, and sheet piles for any soils conditions. With point protection, piles can be driven through boulders, layered rock, garbage dumps, and waterfront debris to provide dependable support for all types of structures. Splicers for pipe piles can be tapered for a water-tight drive-fit that does not require welding. The pipe splicer can be made applicable to precast concrete piles. Splicers for H make the long pile as strong as an unspliced length with only simple welding. Transition splicers quickly connect different types or sizes into efficient composite piles.

Jan 1, 2010

By Mark Johnson, Mathew Janes

"The Resonator RD 260 Resonant Pile Driver delivers ground disturbance free, high production pile driving. The Resonator has recently been used on numerous production pile driving sites in the Netherlands and Melbourne, Australia to drive piles in sensitive areas where conventional pile drivers could not be used. Two case histories are provide in this paper which demonstrate the features and benefits of Resonant pile installation.. In the Netherlands the Resonator RD 260 was used at the Vopak Oil Storage facility in the Port of Rotterdam to install pipe and sheet pile within an active pumping gallery. The site demanded vibration free pile installation to construct a cofferdam within sensitive, highly valued assets. Access was an issue and schedule demands were stringent as shutdown windows were narrow. The RD 260 provided ground disturbance free piling immediately adjacent to fragile structures. At Vopak the only site access was using a large crane positioned over 40 m from the location of pile driving. Driving was conducted amongst 900 mm dia pipes carrying heated crude oil.In Melbourne the RD 260 was used to drive GU 18 sheet piling adjacent to light rail easements. The project was the first of many grade separations being constructed within Melbourne urban areas to lower the light rail and provide quieter rapid transit. The original trial used an RGT MR105 series vibrator but noise and vibration criteria were exceeded. The RD 260 was brought in for a trial and performed with high production and produced negligible ground vibration. Up to 17 sheet piles 14 m in length were driven in a 2.5 hour window during the trial.IntroductionThe Resonant Pile Driving method is gaining acceptance around the world as a new method to rapidly drive piles free of ground borne vibrations. The high frequency vibrator resonates the pile, essentially turning the pile into a spring, to excite the toe of the pile with high accelerations and low amplitude. High acceleration with low amplitude generates high penetration rates but the high frequency stress waves are quickly dissipated in the soil. Typically ground borne vibrations are measured at below 1 mm/sec within 1 to 5 m of the pile. The Resonant method can drive a pile next to a glass of wine, without spilling, as has been demonstrated on numerous piling sites.How Does Resonance Work?The Resonant method uses a hydraulic piston - cylinder geometry to generate high magnitude, high frequency oscillating force. This is a very different mechanism than the eccentric mass technology used in conventional and variable moment vibrators.A unique valve geometry achieves the high frequency flow switching necessary to oscillate the hydraulic piston at up to 180 Hz (10800 VPM). The valve is controlled electronically for maximum accuracy of the desired frequency. The volume of hydraulic oil delivered through the valve to the piston (flow rate) determines the amplitude while the hydraulic pressure determines the peak force."

Jan 1, 1900

By Daniel Magill, Jim Gentry

"Acrylamide chemical grout (C3H2NO) has been successfully used for over 50 years to control groundwater and stop infiltration. This paper will address three unique projects involving the control of groundwater with each study providing special circumstances and geological conditions: encapsulation of radioactive hazardous waste in the United States, a tailings dam for a large copper/gold mine in Argentina and 27 miles of leaking subway in Canada. The primary reasons for selecting acrylamide grout were based on the following characteristics: thinnest chemical grout on the market, a true solution grout which contains no suspended solids in the blended product, flexible gel set times, and a 362 year half-life in soil as determined by the U.S. Department of Energy.INTRODUCTIONChemical grouting has been successfully used for over fifty years to control the movement of groundwater in a wide variety of applications including:•, Hazardous Waste Containment•, Subways & Tunnels•, Mines & Tailings Dams•, Concrete & Earthen Dams•, Underwater Structures•, Beneath/Around Underground Structures•, Mainline Sewers, Laterals, Manholes•, Large Soil Stabilization ProjectsThis presentation will review three projects where chemical grout was utilized to address some very difficult water control challenges, each providing special circumstances and geological conditions:1. Pre-construction seepage control at a mine tailings dam2. 27 miles of leaking subway3. Encapsulation of radio-active hazardous wasteThe reasons for selecting acrylamide grout as the solution for controlling groundwater in these selected projects were based on the following characteristics:1. Acrylamide grout is the thinnest chemical grout on the market2. No suspended solids which allows acrylamide grout to travel anywhere water can travel3. Flexible gel set times from 5 seconds to 10+ hours4. U.S. Department of Energy studies conclude that acrylamide chemical grout has a 362 year half-life in soil and can reduce the permeability of rock/soil to less than 10-8 meters per second (m/s)"

Jan 1, 2017

By Joram M. Amir

Even when they are cased! [ ] In bored piles, as well as in drilled shafts, and in caissons too, defects will occur! [ ]

Jan 1, 2001

By JO Choi

Jet-grouting method is a useful technique to reinforce foundations on relatively soft or vulnerable soil layers such as fractured zone and stratum with cavities. Although jet-grouting has been widely applied to various field works, a reliable design standard has not been established yet. A number of model tests were performed to investigate end bearing behaviors of piles reinforced by jet-grouting. It was concluded that end bearing capacity was increased in proportion to uniaxial compressive strength of grout column. Based on the test results, the design criteria for the end bearing capacity were suggested.

Jan 1, 2006

By Martin B. Hudson, Kenneth S. Hudson, Gwendolyn Arreguin

A twin high-rise project site in Century City posed several foundation engineering challenges for the design team. One portion of the twin high-rise project site was required to utilize top-down construction in order to allow a driveway to remain open during construction of the project’s 40-foot deep excavation. The challenge was compounded by the need to utilize a mat foundation to support the high-rise construction and yet have temporary drilled shafts through the mat foundation area that would not create excessive differential settlement. This was accomplished by constructing a deck supported by eight drilled end- bearing drilled shafts with Osterberg load cells and five 7-foot-diameter end-bearing drilled shafts. The Osterberg load cells served to verify the capacity of each of the drilled shafts and preload the soils at the drilled shaft tips. The 7-foot-diameter shafts were constructed with bond breakers to prevent skin friction but instead mobilize end bearing (for settlement compatibility with the surrounding mat foundation). After the drilled shafts were placed, then top-down construction began beneath the driveway, leaving the driveway supported on the drilled shafts. Construction challenges included drilling of the shafts through previously abandoned tieback anchors from an adjacent parking structure basement, as well as cemented layers within the rock materials. The paper describes the use of the various analytical methods used to calculate capacities and check settlement compatibility, the construction and testing methods utilized, and the construction challenges encountered. INTRODUCTION Wood Environment and Infrastructure Solutions, Inc. (hereafter referred to as Wood) performed a geotechnical investigation for the New Century Plaza currently being constructed in the Century City District of Los Angeles, California. The New Century Plaza project consists of the construction of two new towers (designated as North and South Buildings) and the rehabilitation of the existing Hyatt Regency Century Plaza Hotel. The existing hotel tower is 15 stories in height above the existing grade and is underlain by four subterranean basement parking levels. The new North and South Buildings will stand approximately 46 stories in height above the existing grade to accommodate residential use. The new towers are planned west of the existing hotel. The site was previously occupied by the existing hotel subterranean parking structure and overlying podium structure, and a loading dock in the southwest portion of the site. The former western portion of the podium and subterranean parking structure west of the existing hotel building western edge were demolished to allow for new subterranean levels, a new podium structure, and the new towers. The lowest floor of the proposed subterranean level required excavation on the order of 35 to 80 feet.

Jan 1, 2019

By Allan Herse

"The years following World War II were nation building years in Australia. Soldiers returned from the European and Asian theatres of war sparking a major infrastructure construction boom. Dams and highways were built to keep up with the growth of towns and cities, which were bursting at the seams, not just from the returning soldiers settling down with their families but also from the many waves of refugees from war torn areas around the globe.The demand for electricity generation and distribution required for the growing population sparked the expansion of the national power grid with new high-voltage transmission towers appearing across the landscape. However, with an original design life of 50 years, those transmission lines constructed in the 1950s are nearing, or are at the end of, their anticipated service life.In recent years, the Australian power distribution network has changed from a period of high construction activity in greenfield high-voltage lines to a period that is now focused on reducing cost and maintaining existing assets. Replacing aboveground structural members and electrical components is relatively simple even under live conditions. However, the replacement or repair of tower foundations, many of which are in remote locations, has been a problem that has caused difficulties for power utilities trying to operate on a budget while also avoiding costly and unpopular power outages.With thousands of miles of aging transmission lines needing life extension work, Piling & Civil Australia (PCA) has developed a patented system of upgrading the foundations with micropiles while under live-line conditions without requiring costly outages. The system is seen as revolutionary by power utilities, allowing the utilities to extend the life of their existing assets until demand increases to warrant the construction of a new line. PCA has been working on a potential solution with Powerlink Queensland for the past 5 years to develop a quick and cost-effective foundation replacement system that can extend the life of its existing asset base anywhere from an additional 5 years to 50 years.With design support from Quanta Subsurface, USA, PCA recently completed the foundation replacement of 26 lattice tower foundations in the Townsville region of North Queensland. Using a steel bracket (patent pending) to connect hollow bar micropiles to the lattice towers, the installation techniques that were developed enabled the micropiles to be installed within a tolerance of less than about 3/8 in (10 mm) through the existing steel grillage foundation while maintaining live line conditions. The project was an Australian first and a trial by Powerlink for wider use within its network, and it was delivered on time and within budget at one tenth of the cost of traditional methods."

Jan 1, 2017

By Allan Herse

"The years following World War II were nation building years in Australia. Soldiers returned from the European and Asian theatres of war sparking a major infrastructure construction boom. Dams and highways were built to keep up with the growth of towns and cities, which were bursting at the seams, not just from the returning soldiers settling down with their families but also from the many waves of refugees from war torn areas around the globe.The demand for electricity generation and distribution required for the growing population sparked the expansion of the national power grid with new high-voltage transmission towers appearing across the landscape. However, with an original design life of 50 years, those transmission lines constructed in the 1950s are nearing, or are at the end of, their anticipated service life.In recent years, the Australian power distribution network has changed from a period of high construction activity in greenfield high-voltage lines to a period that is now focused on reducing cost and maintaining existing assets. Replacing aboveground structural members and electrical components is relatively simple even under live conditions. However, the replacement or repair of tower foundations, many of which are in remote locations, has been a problem that has caused difficulties for power utilities trying to operate on a budget while also avoiding costly and unpopular power outages. With thousands of miles of aging transmission lines needing life extension work, Piling & Civil Australia (PCA) has developed a patented system of upgrading the foundations with micropiles while under live-line conditions without requiring costly outages. The system is seen as revolutionary by power utilities, allowing the utilities to extend the life of their existing assets until demand increases to warrant the construction of a new line. PCA has been working on a potential solution with Powerlink Queensland for the past 5 years to develop a quick and cost-effective foundation replacement system that can extend the life of its existing asset base anywhere from an additional 5 years to 50 years.With design support from Quanta Subsurface, USA, PCA recently completed the foundation replacement of 26 lattice tower foundations in the Townsville region of North Queensland. Using a steel bracket (patent pending) to connect hollow bar micropiles to the lattice towers, the installation techniques that were developed enabled the micropiles to be installed within a tolerance of less than about 3/8 in (10 mm) through the existing steel grillage foundation while maintaining live line conditions. The project was an Australian first and a trial by Powerlink for wider use within its network, and it was delivered on time and within budget at one tenth of the cost of traditional methods."

Jan 1, 2017

By David E. Albus, Bidjan Ghahreman

A single-family home constructed on the side of a slope in Los Angeles, CA, was subjected to lateral forces due to soil slope creep on the pile foundation supporting the home. Impacts to the property included cracking and separations in the street, retaining walls, exterior concrete flatwork, and decorative concrete features in the rear yard area. The home was supported by concrete piles that penetrated the surficial soil mantle and were embedded in underlying bedrock. However, the home exhibited minor distress that suggested even the home was being affected by soil creep. Selected points on the home were monitored with an optical survey method and manometer over a period of two years to assess if the home was undergoing vertical or lateral movement. Monitoring data indicated the home was in fact moving down slope in a manner consistent with slope creep. As a result, the authors were concerned that continued movement due to slope creep could result in over-stressing of the piles that support the home and ultimately lead to failure of the foundation system. An evaluation was then undertaken to evaluate the behavior of the foundation system due to forces from slope creep. Research was performed during the course of evaluating the conditions to consider various approaches to modeling pile behavior of the piles supporting the home. Some research has been performed to field measure creep displacement of soils and rock in slopes. These previous works have found a diverse behavior of the soil displacement with depth (velocity profile) indicating the process is very complex. An example of various velocity profiles measured in field experiments is depicted in Figure 1. Other research focused on theoretical models of velocity profiles and exhibited similarities to some of the field measured cases.

Jan 1, 2018

By Christian Divis

[ ]

Jan 1, 2002

By Adrian M. Keller

Borehole televiewers are downhole inspection devices available for high-resolution imaging of a borehole wall following rock coring. Borehole televiewers should be considered by geotechnical engineers and geologists as a supplemental way of investigating rock for deep foundations. The optical televiewer (OTV) produces a digital optical image and the acoustic televiewer (ATV) utilizes reflected acoustic waves to produce images of the borehole walls. These devices can be utilized to examine soft or fractured zones in the rock mass, solution features, open joints or other voids not observable from traditional rock coring techniques. These devices along with computer post-processing can determine the strike and dip of joints, bedding planes, shear surfaces, or other structural features, eliminating the need for expensive oriented cores or manned downhole logging. An acoustic televiewer was utilized in the Fall of 2008 during the investigation phase for the I-70 New Mississippi River Bridge (I-70 MRB) in St. Louis, Missouri. Voids and fractures in the upper portion of the rock were described by prior consultants. Further investigation of these features was necessary to evaluate deep foundation options to support the main towers. Ten borings were drilled from a barge in the river at the two main tower pier locations. An ATV was utilized in each of the ten borings to produce images of the rock mass in the borehole and allow further investigation of the voids. Voids interpreted as solution features were readily identified in the ATV logs in multiple borings and at similar elevations, suggesting connectivity. Measurements of the voids? width, location in the borehole and orientation allowed a more thorough understanding of the potential impact the solution features may have on the planned deep foundations. An extensive grouting program was eliminated based on the ATV results.

Jan 1, 2010

By Paul Hewitt, Aaron Rastall

The New South Wales South Coast rail corridor is key infrastructure for both freight and passenger transport. Geomorphological and geological evidence suggests that land instability has been widespread throughout sections of the rail corridor, long before the first documented record of landslide activity in 1879. Major landslides occurred along a 25-km length of the South Coast Railway connecting Sydney and Wollongong because of significant rainfall events of the late 1980s. Since this time, several sites have been identified as subject to instability and treated progressively under a risk priority and safety management system. Two such sites comprise a station footbridge and overhead wiring structure (OHWS), both founded on high embankments overlying colluvial materials resulting in the structures’ potential movement and associated stability concerns. This paper presents these two sites as case studies, and discusses the project geology, geotechnical models developed, interpretation of monitoring data, and successful remediation of the rail structures using sleeved bored piles. The sleeved pile system was used to isolate bored piles, which separated the bridge foundations and OHWS from the moving soil mass to ensure the piles can carry the rail structure loads, unaffected by downslope soil movements.

Nov 1, 2022