Search Documents

By Dena Morgan, Emre Biringen

"Abstract This paper discusses the execution of pile installation and design issues at two environmentally challenging industrial sites in North America. Environmental regulations set constraints on the design and require versatility in choice of technology.For a proposed bridge, due to protected fish habitat, performing soil borings within 30 m of the creek embankment was prohibited. The limited subsurface profile indicated a thick upper layer of granular material, thus driving H-piles was considered. However, to limit generation of vibration and noise in the protected area, drilled piles had to be used. During execution, the subsurface profile differed from that in the borings 30 m away. Very soft, saturated silt was encountered at the bottom of the caisson and the length had to be redesigned very quickly while the contractor waited for instruction. For a new structure in uncontrolled fill area, performing soil borings was not allowed. It was known that a layer of peat was present in the area, but no information regarding the thickness and extent. The subsurface profile generally consisted of granular material overlying a thick compressible silt layer. Somewhere within the granular layer peat would likely be encountered. Franki piles were chosen to penetrate the peat and bear in the underlying granular material. During environmental sampling in the area, methane gas was encountered and Franki piles were no longer a viable option due to safety concerns. The foundation system was changed to steel H-piles driven to bedrock, which was more than 50 m below the ground surface and sloping. Rock shoes that would work to significant slopes had to be used in order to increase the likelihood of good embedment within the bedrock. Also, due to obstruction of an approximately 3 m thick debris field that was encountered in the upper granular soils, some of the piles had to be relocated and extra piling needed to compensate for such differences. The results of PDA testing to estimate compressive capacity and a series of lateral load tests are presented.INTRODUCTIONThe design issues that are encountered during construction can be quite problematic and have a significant impact on schedule. In order to avoid such impact on the project, a thorough subsurface investigation should be considered prior to design and construction. Better understanding of environmental regulations also prevents costly changes to the foundation design. This paper discusses the execution of pile installation and the design issues at two environmentally challenging sites in North America.BRIDGEDuring the subsurface investigation for a proposed industrial building complex, several boreholes were drilled within the footprint or in close proximity of various structures, with Standard Penetration (SPT) sampling of the upper coarse-grained soils (sand/gravel) and undisturbed sampling of the lower fine-grained soils (silt/clay). The SPT blow counts (N60) were corrected by a factor of 1.35 in order to incorporate the SPT automatic energy transfer ratio. When Modified California Sampler was used, a correction factor of 0.44 to 0.64 was also applied. N60 values were further corrected for gravel to avoid artificially high blow counts during the analyses due to spoon samples contact with gravel and cobbles, and the corrected values of (NG)60 (limited to a maximum value of 50 blows/300 mm) were used for design. The information from the SPT boreholes was then used to assess the subsurface conditions beneath the structures, as well as for a nearby bridge that was designed to cross over a creek. Since performing soil borings within 30 m of the creek embankment was prohibited due to the protected fish habitat, the investigation with regard to the bridge abutments was limited to two deep boreholes (B10-33 and B10-34) at the bridge location and two additional boreholes (B10-35 and B10- 36) located approximately 200 m upstream. The bridge location and two sets of boreholes are"

Jan 1, 2014

By Peter Deming

"PART 2 OF 2 (CONTINUED FROM SUMMER 2006 EDITION) CONSTRUCTION ISSUES (cont’d) The Influence of Ground Conditions on Collapse Sand and gravel strata provide frictional resistance to support active earth pressure. The angle of internal friction has only slight influence on computed stability. Sand and gravel material design parameters can be defined with SPT N-values. Silt strata should be analyzed using internal friction. Definition of soil parameters should be performed by laboratory testing. Cohesive materials, especially soft clay and peat, require careful definition for design. Shear strength should be determined by laboratory testing. Work platforms constructed over granular strata improve the ground resistance by increasing confining pressure. However, temporarily increasing overburden stress on cohesive ground reduces trench stability. If the ground contains soft cohesive deposits which are not normally consolidated to the construction overburden, these must be stabilized before attempting trench construction. Use of wick drains and surcharge fill to improve the ground is recommended. Ground stabilization work requires time, and should be performed by the Owner prior to trench excavation. The addition of cement, stone columns, or other measures to support trench excavation equipment is typically determined to be more expensive and less dependable than ground improvement. Excavation through peat can be especially problematic. Peat materials rapidly compress when earth pressures exceed preconsolidation stresses. Backfill materials provide a horizontal stress on the trench wall which can exceed the bearing capacity of peat. As the peat compresses, the trench becomes wider, and slurry levels drop and trench stability can rapidly deteriorate. If the peat is the closure layer, a shallow key is recommended. If peat is present on the trench wall, preconsolidation with surcharge is recommended. Bottom preparation and Backfill Placement Trench wall stability is a temporary condition which must be controlled by proper design and construction of work platforms and slurry features which influence ground support. Backfill materials and intimate contact of the backfill with the closure layer are permanent conditions which are the end goal of the work. The most common reason slurry trenches fail to provide working barriers is improper bottom closure. Either the closure layer is not engaged, or the backfill is not in intimate contact with the closure layer. This can result from construction problems associated with sidewall collapse described above, slurry performance and/or degradation, backfill placement methods, and failure to maintain the trench bottom clear of sediment prior to placing backfill."

Jan 1, 2006

By SungJe Chi

Intrinsic remediation is the effect of natural attenuation mechanisms - dilution, dispersion, sorption/precipitation and biodegradation - reducing contaminant concentrations in ground water to specified levels at predetermined compliance points in the aquifer. Current monitoring and modeling for post closure was used to assess the current and long-term potential of intrinsic remediation of contaminated seepage originating from a large reactive (sulfidic) tailings impoundment near Questa, New Mexico. It is concluded that the natural attenuation mechanisms of precipitation within the tailings (as a result of buffering) and dilution/dispersion within the aquifer are currently active and likely sufficient to reduce contaminant concentrations to below state standards in the long-term. Other natural attenuation mechanisms such as sorption and biodegradation within the receiving aquife4s) were not assessed here, but are likely further reducing contaminant concentrations. Active interception and recovery of the seepage water is being maintained until monitoring demonstrates that intrinsic remediation has successfully achieved the level of water quality control required.

Jan 1, 2017

By Donald A. Bruce

"Abstract The Deep Mixing Methods (DMM), in their current forms, have been employed in the United States since 1986, although an earlier version had seen service from 1954. The earlier developments were strongly influenced by practices in the Nordic countries and Japan, while by the late 1980’s several DMM systems had been developed in the U.S. itself. Since then, DMM has continued its evolution, principally via the challenges of a series of large, landmark projects, but also via distinct, significant technological advances. This paper highlights the key points in the history of DMM in the U.S., and provides an overview of the different methods currently in use.In the BeginningIt is a common misconception that the history of applications of the Deep Mixing Methods (DMM) in the United States dates from 1986 when SMW Seiko Inc. — a subsidiary of Japan’s Seiko Kogyo Company — was established in the Bay Area. However, the author believes that Intrusion Prepakt Co.’s patented MIP (Mixed in Place) system had been used, albeit sporadically (about 30 projects are recorded), since 1954 (FHWA 2000, 2001). Ironically, by 1961 this single auger method had been extensively used under license in Japan for excavation support and groundwater control — by the Seiko Kogyo Company. By 1972, the original MIP technique had been succeeded by more advanced Japanese methods, involving multiple augers. Intrusion Prepakt have long since become defunct.The first systematic studies of contemporary Deep Mixing Methods in Japan began in 1967 when the Port and Harbor Research Institute of the Ministry of Transportation began laboratory testing using granular and powdered lime for treating soft marine soils. Fundamental studies continued through the early 1970’s, by which time the development of industrial scale equipment was well advanced, having its first application on a marine trial near Haneda Airport. Coincidentally, laboratory and field research also began in 1967 in Sweden (“Swedish Lime Column Method”) for treating soft clays using unslaked lime. Reportedly the progenitor was a Norwegian, Kjeld Paus, who had made observations on fluid lime columns in the U.S. It would seem that developments in Japan and the Nordic countries proceeded independently until 1975 when the technology leaders from each group (Broms and Boman; and Okumura and Terashi, respectively) presented their — very similar — findings at a conference in Bangalore, India. Limited technical exchanges ensued thereafter.Whereas the Nordic developments continued to focus on the use of dry reagents (cement and lime) and relatively light equipment compatible with operating on and in very soft clays and organics, the Japanese progressed into the use of fluid reagents (cement-based grouts) and heavier equipment for both marine and land-based projects. Thus, by 1986, there were a large number of proprietary (wet and dry) DMM systems in Japan, and a rapidly growing market already by then accounting for over 12,000,000 m3 of ground treatment."

Jan 1, 2014

By Ronald Damen, Dion Denes

"Friction fatigue is the loss of soil-pile friction around the shaft area of the pile. It has been observed during impact driving of piles, and has been modelled to a limited degree using physical scale models. This paper proposes the use of high strain dynamic pile testing to assess and quantify friction fatigue in impact driven piles. The method is applied to two case studies: one on a project off the north-west coast of Australia and one on a South Pacific Island. On both sites calcareous sand layers are present. Pile Driving Analyzer (PDA) monitoring has been conducted during impact driving of steel piles, which allowed for assessment of shaft resistance development both with depth and with progressive driving, by use of wave equation signal matching. Lessons are drawn from the case studies to improve future observations.INTRODUCTIONFriction fatigue is the loss of soil-pile friction around the shaft area of the pile, under cyclic loading or during pile driving. The phenomenon has been frequently observed in some non-silica sands, such as pumice sands and calcareous sands and has been the subject of academic study.The occurrence of friction fatigue impacts the driving behaviour of piles and the shaft friction component of the ultimate geotechnical strength (Rd,ug). If potential friction fatigue is not recognised in the design phase of a project, required pile toe levels can be significantly underestimated. This could lead to extra cost and delays, or, if no adequate pile verification is conducted, to geotechnical failure or underperformance of piles. This is especially true in remote locations, such as Pacific islands, where calcareous material is often present.A better understanding of the phenomenon would aid both pile design and driveability assessment. This paper proposes the use of high strain dynamic pile testing to assess and quantify the effect of friction fatigue from impact driving. Two case studies are presented in which high strain dynamic testing has been conducted on driven piles in calcareous sands to illustrate the method.BACKGROUNDFriction fatigueThe geotechnical strength of piles is composed of the resistance to static loading by the base of the pile and the shear resistance between the shaft of the pile and the adjacent soil. The latter is often referred to as the shaft resistance or shaft friction.During impact pile driving, a decrease in shaft resistance is often observed. Although this phenomenon is also observed during vibratory pile installation, this paper deals predominantly with impact driving. This decrease in material strength from the tip of the pile influences the shaft resistance and may be either temporary or permanent. Temporary reduction in shaft resistance is common in cohesive soils and is thought to be caused by excess pore water pressure, which has insufficient time to dissipate. This phenomenon, commonly referred to as set up, is observed to a significantly lesser extent in non-cohesive materials such as clean sands (Rausche et al., 2004)."

Jan 1, 1900

By Tony Mazzo

It has often been said by consulting engineers that foundation contractors are in the business of taking risks. One would agree that the mere fact a foundation project can be budgeted, planned, engineered and executed solely on the reliability of eight test borings made at a proposed site having an area of approximately 19,000 square feet, is a risky proposition, in and of itself. Now imagine that this site is actually one half of a city block located in an urban setting in an old, congested, historical neighborhood, surrounded by narrow city streets and historic landmark buildings. And suppose that the required depth of excavation for the construction of the new building on this site is approximately 35 feet and the natural groundwater table is at a depth below existing grade of only 25 feet. Given the difficult site conditions outlined above, one could certainly add the words "challenging" and "complicated" to the inherent word "risky" when describing the construction techniques involved to undertake a foundation project of this magnitude. This case study will discuss in detail how the excavation, sheeting, dewatering and underpinning work was accomplished as well as the problems overcome along the way.

Jan 1, 2003

By Chu E. Ho, Paul Napoli

A new waterfront park was developed on Long Island in close proximity to the East River and Newtown Creek. The existing ground consisted of fill over soft organic clay, medium dense silty sand, glacial till and schist bedrock. The ground was initially raised to preload the underlying soft soils to stabilize the ground in preparation for site development. The ground was subsequently cut down to temporary grades for installation of foundation piles for the overlook structures and construction of reinforced concrete cantilever retaining walls forming pathways located adjacent to the water bodies. The retaining walls were located in two rows at different elevations along the sides of a steep embankment. Where the pathways converge, some of the walls were too close to each other, and were redesigned as a combined U-wall with a common base slab. The individual retaining walls were designed for adequate bearing, sliding and overturning resistance. Ground anchors were installed to enhance global stability of the retaining walls. This paper presents the design considerations for the retaining walls for various loading conditions, and evaluation of the trial and proof tests for the anchors. INTRODUCTION The New York City Master Plan included the transformation of an approximately 30-acre parcel of land in Long Island City, Queens, New York from a former manufacturing zone into a residential, commercial and recreational zone for middle-income community. The site was located at Hunters Point South along the eastern shoreline of the East River and Newtown Creek (Figure 1). The development included low to high- rise residential buildings, a public school, and retail structures. Open spaces were provided along the East River and Newtown Creek waterfronts in the form of a continuous park providing for recreational and community-related activities. Waterfront structures included small park buildings, walkways and viewing platforms. The shoreline was surrounded by revetments as part of the flood mitigation strategy. The project involved extensive site re-grading and several retaining walls were constructed. The earthwork volume amounted to approximately 47,000 cubic yard of imported fill and 93,000 cubic yard of cut. The exposed height of the retaining walls ranged from 3 to 15 feet. This paper focuses on the design and construction of the retaining walls for the project.

Jan 1, 2019

By Mauricio Coto

Three bidirectional static load tests (BDSLT) were executed on bored concrete piles, as part of the permanent foundations for two buildings sites located at the Sabana, San Jose, Costa Rica, separated at a relatively short distance of about 1 km. Unit skin friction values obtained for both sites, principally for the “Lahar” layer show that in general, friction pile capacity from the tests is higher than anticipated per static calculations from soil borings geotechnical parameters correlations. Results from the tests were also compared with dynamic load tests (DLT) executed at other two sites in the surrounding area, and with a Finite Element (FE) Analysis that model soil-pile interaction for one of the projects. On the other side, some construction issues were detected on one of the sites, which negatively affected the end bearing capacity, but being that pile friction was higher than anticipated, the required overall pile capacity was accomplished. The BDSLTs results of these tests help to better understand the geotechnical behavior of the soil layers in the Sabana. Moreover, they also show that is possible to optimize the design and construction of other bored pile supported buildings and structures on the zone.

By Mohammed Sakr

This paper presents the results of a full-scale axial compression and tension (uplift) testing program executed on large-capacity helical piles installed in very stiff to very hard clay till soils (i.e. cohesive soils). A total of ten tests including six axial compression tests and four tension (uplift) tests were carried out. The results of the axial compressive and tensile pile load tests and field monitoring of helical piles with either a single helix or double helix are presented in this paper. Helical piles are traditionally used to support light to medium loads (i.e. loads up to 500 kN or 56 tons). However the results of the present study confirmed that helical piles can support significantly higher axial compressive loads up to 2450 kN or 275 tons, which is about 5 times traditional design loads. The study also demonstrated the high tensile capacities of helical piles which was as high as 85% of their compressive capacity. Hence helical piles can provide a viable design option for foundations supporting relatively heavy loads.

Jan 1, 2012

By Patrick J. Hannigan, Alex Ryberg, Rozbeh B. Moghaddam

Driven piles are widely used for foundation support. In the vast majority of cases, an increase in pile capacity occurs with time which is referred to as “set-up.” However, in a very limited number of cases, a decrease in capacity with time can occur. This phenomenon is referred to as “relaxation.” This paper will provide a brief review of the relaxation phenomenon, as well as pile driving information and dynamic test data on cases where relaxation has occurred. The pile types in the presented relaxation cases include H-piles, open-end and closed-end pipe piles, prestressed concrete piles, and prestressed concrete piles with H-pile stingers. The soil conditions where relaxation occurred includes dense to very dense fine sands, heavily over consolidated clays, and weak laminated rocks. Relaxation information from 36 piles at 26 sites is assessed. The collected data will assist foundation designers by identifying the subsurface conditions where relaxation has occurred, as well as by documenting the corresponding relaxation magnitude. One method of addressing relaxation when it is encountered is to drive the foundation piles to a greater end of initial driving capacity than required long-term. Hence, the identification and quantification of the relaxation magnitude will be beneficial to foundation designers installing similar pile types in similar subsurface conditions. The paper will also present pertinent observations and recommendations on mitigating relaxation when encountered. INTRODUCTION One of the earliest observations of a decrease in redriving resistance following initial driving was reported by Miller (1937). He reported that piles driven into a saturated, coarse grained soil could lose 40 to 50% of their resistance when redriven 24 hours after initial driving. Yang (1956) similarly reported that after a break in driving, a decrease in driving resistance could be encountered for piles driven in dense fine sand, inorganic silt, or stiff fissured clay. Parsons (1966) in his paper that described piling difficulties in the New York City metropolitan area termed this phenomenon “relaxation”. In this time period, pile capacity was most often evaluated from a pile driving formula frequently checked by a static load test. Hence, the true magnitude of the capacity decrease on a given pile was often poorly quantified. Furthermore, dynamic measurements that could determine what influence driving system performance variation had on the observed redriving resistance were not yet readily available.

Jan 1, 2019

By W. Sondermann

"AbstractWith the increasing demand in reuse of inner city areas and the urgent need for deeper foundation pits under cramped circumstances, adjacent structures close to and high ground water level, the well-known established technologies especially with small to mid-sized dimensions are often too time consuming and occasionally not economic to install lateral support systems. The alternatives for these specific cases could be the usage of the deep mixing technology to create lateral support systems in reinforcing the deep mixing elements additionally to transfer the horizontal loads from earth – and water-pressure.With increasing demand in depth and water tightness, verticality and overlapping of single column solutions are becoming the key in execution. In addition, for some applications subsoil-conditions were not ideal for wet deep mixing technologies. The tubular soil mixing system (TSM) as a combination of mechanical mixing and support of hydraulic cutting by jet grouting can provide solutions toovercome these challenges.1. Current market conditions and trendsThe present financial crisis and the efforts not only to consolidate national budgets, but also to rescue certain banks, have not left the building industry unaffected either. Some drastic cutbacks to public budgets, along with the increasingly restrictive granting of credit for the financing of construction projects, have led to enormous over-capacities in the building sector, with purely negative impact. As a consequence of these negative developments, many companies are experiencing the pressure to restructure more quickly and to reduce costs but at the same time to keep the consequences of all activities, both externally and internally, within limits acceptable to employees, owners and finance institutions and last but not least consumers."

Jan 1, 2014

By Patrick J. Hannigan, Geir Veslegard, Frank Rausche, Rozbeh B. Moghaddam

A common type of deep foundation used in Norway to support bridge structures is the drilled pipe piles (piles) filled with concrete reinforcement after installation. The standard installation practice is the use of down-hole hammers. Complex geology and difficult subsoil conditions in Norway causes a high variability of soil and rock layers which in turn make for differences between actual subsurface conditions and those expected from geotechnical exploratory borings. This situation is strongly noted when the foundations are not fully socketed, and the rock layer is sloped. In this particular case, special testing procedures are required to assess the drilled pile base material and evaluate the rock-socket to ensure full contact between the foundation base and the rock surface. The local standard practice to verify the latter condition, consists of coring and visually evaluating the material recovered at the bottom of the drilled pile. This paper presents a case where the coring and visual inspection were not possible and alternatively the geological material encountered at the base of the deep foundations was evaluated using force-displacement measurements. Two 1016-mm (40in) diameter open-end drilled piles identified as P02-04 and P02-05 were tested and evaluated using in-situ force-displacement data prior to filling the piles with concrete. Test results showed an average displacement of 7mm (0.28in) corresponding to 35MPa (5.1ksi) stress level for P02-04, and 7.2mm (0.28in) corresponding to a stress level of 38MPa (5.5ksi). Based on testing results, both drilled piles were within the established material assessment criterion presented by the local authorities. INTRODUCTION This paper presents a case study in Norway where the material encountered at the base of an open- end drilled pipe pile (pile) was evaluated using force-displacement data. In the deep foundation industry in Norway, it is a common practice to install piles to support transportation structures. Once the piles reach the embedment elevation, and the pile base is assessed, these are filled with concrete. In projects where sloping rock is the supporting layer, and all nominal loads are supported by the pile base resistance, assessing the material encountered at the pile base to ensure full contact with the rock becomes critical. The local practice to make this assessment consists of the use of weighted tape, coring, or inspection cameras. However, similar to any other testing and evaluation methods, these come with their own limitations. The variability associated with the use of the weighted tape, accessibility for the coring equipment to complete a coring process, or the conditions at the foundation base such as murky water or thick drilling fluids could significantly impact the photo or video quality taken at the pile base. In such conditions, it is important to consider alternate testing methods to evaluate the material at the foundation base.

Jan 1, 2018

By Paul Doherty

Expansion of the global piling industry has been coupled with significant research efforts investigating the mechanisms controlling pile capacity. Static pile design has transitioned from total stress approaches toward effective stress design, with associated improvements in predicting pile performance. As a result, the available literature is heavily skewed toward static capacity prediction. However, when considering piles offshore, the majority of loading is not static but highly variable and cyclic in nature. This paper outlines the additional factors that require consideration for cyclic pile design, including elevated loading rates, cyclic displacements and capacity degradation. A review of the literature identified a number of cyclic pile testing programs which are collated in this paper. General trends are established through comparison of the tests within the database and the conditions where cyclic loading is most likely to be a concern are identified. In particular, loading conditions which involve full plastic shear reversals are seen to cause the most extreme cyclic damage, with the degraded capacity as low as 31% of the precyclic static capacity. The underlying mechanisms which can result in cyclic damage are explored, with particular attention given to the pore pressure response, radial stresses, shear transfer and particle reorientation.

Jan 1, 2009

By W. Robert Thompson

Hurricane Katrina caused significant damage to transportation structures on the Gulf coast in August, 2005, including the destruction of the US 90 Bridge over Biloxi Bay, Mississippi. Part of the successful design/build proposal for the replacement bridge included a comprehensive test pile program of indicator piles and load test piles in the geotechnical investigation program. A total of 22 indicator piles were installed on the project using the pile driving analyzer to monitor the pile behavior. Five load tests were performed: two axial Statnamic, two lateral Statnamic, and one static axial. The results of the test pile program established driving criteria for production piles that included end-of-drive blow counts and pile tip elevations with an appropriate allowance for setup. The program also confirmed that the planned installation equipment and techniques of GC Constructors, a joint venture of Massman Construction Co., Kiewit Southern Co., and Traylor Bros., Inc., would install the piles to the design tip elevations before production piles began. An extensive program of restrike measurements at a range of times after initial driving of the indicator piles provided a systematic documentation of pile setup in the soil profiles on the site. These resistance values were used to develop a dimensionless setup factor ?S? as the ratio of the restrike resistance to the end of drive resistance. This factor varied from 1.5 for piles penetrating clays and tipped in sand to 3.0 for piles bearing completely in clay and helped establish an end-of drive blow count that included an allowance for setup. The CAPWAP analyses of restrike data with setup and the load test data were used to confirm the design unit side shear and end bearing values developed from the borings and static capacity calculations and to select the design pile lengths.

Jan 1, 2009

By Amy B. Cerato

The application of this study is to use helical anchors as a foundation system for small wind tower (1 ? 10 kW) guyed cables. Helical anchors are currently used to anchor guyed cables of telecommunication and electric towers. However, the increased dynamic vibrations a wind turbine adds to the tower and foundation system under working loads, as well as extreme environmental conditions (e.g., straight line winds, ice load or sudden furling shocks), require additional knowledge about the behavior of helical anchors. These field conditions were simulated in this study by instrumenting a working tower with load cells and 3-axis accelerometers to gather data on wind speed and tower response. These tower responses were then transmitted to the helical anchors through an extensive, large-scale testing program that included monitoring the performance of the helical anchor foundation under dynamic loads, subject to natural variations in both wind regimes, precipitation (water level) and variations in helical anchor geometry. This paper specifically discusses the effects of helical anchor geometry on helical anchor performance under long-term dynamic loads.

Jan 1, 2008

By Richard Short

Shallow rainfall-induced landslides in residual and colluvial hillslopes and steep embankments are a common occurrence in many settings [1, 2, 3]. While occasionally posing a threat to property and life-safety, they more often present an ongoing maintenance problem and can lead to the initiation of larger failures. Typically, these slides consist of 2 to 4-foot thick translational movements of silty and clayey soils down slope through the reduction of strength from increases in pore water pressures. Direct surficial infiltration and indirect groundwater seepage are the normative triggers for failure. In the residential community of Blackhawk, California, located east of the San Francisco Bay, these types of landslides are a common occurrence (Figure 1). However, shallow landslides have also been a repetitive and constant problem along many state highways where steep embankments have been constructed in close proximity to busy thoroughfares. Given the real threat to property values in residential and commercial settings and the constant maintenance problem posed to lifeline structures such as utilities, roadways, and pipelines, new methods to deal with these landslides are needed.

Jan 1, 2007

By Cassandra A. Wetzel

"Rock socketed mini-piles are a desirable foundation alternative when design capacity is more than 40 tons and there is limited access. In this case history mini-piles were designed to support between 75 and 200 kips at 12 locations adjacent to a perimeter wall, a party wall and at cast iron column piers. Limited geotechnical information, low overhead clearance, and active building population tested the creativity of the team to get the piles installed. The key geotechnical concern during installation of the mini-piles was the presence of a glacial till layer above the bedrock surface that restricted the seating of the casing into bedrock with a track mounted drill rig. Soil loss during the advancement of the rock socket using an air hammer was excessive and increased the risk of subsidence. Over a three week period the engineer worked with the contractor to modify the design, means, methods, and materials to install piles with adequate load capacity. This paper will present the changes in design and construction methods that were required.INTRODUCTIONRock-socketed mini-piles are a common and desirable deep foundation alternative to support loads more than 40 tons in New York City. Limited vertical clearance, accessibility, vibration control, and load capacity make this pile type attractive; it also does not require a static axial load test when socketed into rock. This added benefit makes this alternative all the more feasible.The installation of a drilled pipe extending to bedrock through a glacial till deposit presented challenges to the contractor and engineers to confirm the casing is seated sufficiently into the rock prior to drilling the rock socket. The loss of soil between the steel pipe and the till/bedrock interface can compromise the performance of the pile and soil loss can result in settlement of the ground surface.This paper presents the design and construction method changes made on one project during the installation of ten limited access rock socketed mini-piles."

Jan 1, 2017

By Mohammed Z. Islam

As cities are growing all over the world, the need for urban transportation facilities are on the rise. Designers (of these facilities) today are faced with a number of constraints for their design, of the most is the space limitation and impact of new construction activities to the community. A typical subway station, as the focus of this paper, is approximately 600 to 1000 feet long, 50 feet wide and 2 to 3 story high. With such a large volume of construction activities, it is easily realized why underground stations are becoming obvious choice for larger cities eventhough the cost could be 2 1/2 to 3 times as much as an aerial station and 4 to 5 times that of an at-grade station [O'Neil et. al.(1977)]. Since cost is an important factor which is always increasing, therefore, the designer should have a good planning, consider alternatives for design and come up with a realistic design with minimum impact to the community. This paper is about the geotechnical considerations that the designer should be aware of. PLANNING A 1977 report [O'Neil et. al.(1977)] on the construction costs for a number of underground subway stations indicate that about 4 0% of the cost is site-controlled, 35% is structural items, and 25% is finish and equipment. It is seen that of opportunity exists for cost savings in the site selection and proper use of the site. Once the site is selected, the cost of construction become controlled by urban conditions at the site, geotechnical conditions, station size and depth. Therefore, the design-solution is very much site-specific. The geotecnical designer should collect the following information at the early phase of the design:

Jan 1, 1993

By Sangseom Jeong, Moonkyung Chung, Junyoung Ko

"Abstract The plugging effect of open-ended piles in sandy soil is analyzed by full-scale field test and plugging measurement. PLR (plug length ratio) measurement data from 144 field cases are analyzed with pile diameter. Based on the plugging measurements, PLR of open-ended piles which have above 1000mm diameter is predicted to be above 0.9. Through plugging measurements, a new empirical method is suggested for quantifying the plugging effect of open-ended piles. The proposed PLR equation is possible to predict the behavior of soil plug in the preliminary design stage. In addition, in order to investigate the behavior of the soil plug of open-ended pile, field load tests are performed on instrumented three piles driven into sand. It is obtained that the resistance components of open-ended pile are separated by double-walled pile system. It is found that inner shaft capacity is developed nearby pile tip. However, upper soil plug did not influence the inner shaft capacity. Also, it is found that all test piles are floating piles and unplugged condition because the sum of inner shaft capacity and outer shaft capacity is calculated about 58 to 76% of the ultimate bearing capacity.INTRODUCTIONIn Korea, a number of huge construction projects such as harbor terminals, offshore grand bridges, and lifeline systems are progress in urban and costal area. In these areas, steel pipe piles are frequently used to support high-rise buildings and heavy weight structures for ensuring structural safety rather than serviceability limit capacity. Also, steel pipe piles are frequently used in civil engineering structures because they have many advantages such as high-load bearing capacity, light weight and outstanding workability. The mega foundations of grand bridges and high-rise buildings are required in geotechnical engineering. Large diameter driven piles are frequently used in several projects.Many specifications such as API, FHWA and AASHTO have been reported as a design guideline of plugging effect, however , the current design method for plugging effect of steel pipe piles are mainly based on the our knowledge derived from observation of the model test or the small diameter pile load test. Therefore, these specifications have limitation to apply the large diameter steel pipe piles.Much work has been done to study the plugging effect by many researchers. Yamahara (1964) reported that soil plug has been modeled as a thin disk element as shown in Figure 1, since the increment of radial strain of the soil plug can be neglected due to high rigidity of the pile compared to that of the soil plug. Klos and Tejchman (1977) reported that the end bearing capacity of open-ended piles was almost equal to that of a closed-ended pile when penetration depth of pile was above 15times the pile diameters by model tests. Paikowsky and Whitman(1990) reported fundamental studies on mechanism of plugging effect in sand. Paik et al. (2003) reported that empirical relations for plug load capacity, annulus load capacity, and shaft load capacity of open-ended piles are proposed based on the model pile tests. As discussed above, much work has been done in the area of plugging effect. But little work has been done to study the plugging effect by full scale field tests."

Jan 1, 2014

By Rudolph P. Frizzi

Structures supported on ACIP and DD piles perform successfully when quality control is maintained from the initial site subsurface investigation through pile design, bidding, and construction. The four stages of ACIP / DD pile construction are: preparation, augering the pile, grout / concrete placement, and reinforcement installation. During all four stages, careful observations and communication between the contractor and the owner's engineering inspection personnel are vital to successful pile completion. Automated monitoring equipment (AME) exists to supplement, but not replace, the field personnel's observations during the pile augering and grouting operations. Full-scale field load testing is done to verify the pile's geotechnical and structural design, and the contractor's pile installation means and methods, using several procedures including: conventional top loading, high-strain dynamic, rapid axial compression (i.e. Fundex PLT and Statnamic), and Osterberg Cell. Non-destructive sonic testing is performed to investigate the below-grade sectional properties of the completed pile; such methods include: low-strain impulse testing, and single-hole and cross-hole sonic logging. Post-construction observations are necessary to verify pile location and top properties prior to overlying cap construction.

Jan 1, 2005