Search Documents

By G. L. Sivakumar Babu, P. Chaithra

"Raft foundations which are used against differential settlements and for carrying heavy loads can still be subjected to excessive settlements even if it is safe against bearing capacity consideration. Providing additional piles under the raft can reduce such settlements to acceptable values. In addition to settlements, the piles also relieve the raft a part of the total load and thus the bearing capacity of the Combined piled raft foundation (CPRF) is improved. Parametric study of response of piled raft foundation has been conducted and the results have been presented. The study is conducted using finite element based software, PLAXIS 2D. The main objective of the paper is to evaluate the parameters that affect the performance of piled raft for an economical and effective design. It has been shown that piled rafts are an economical solution in foundation design compared to raft foundation, for the soil conditions considered in the paper.1. INTRODUCTIONThe aim during the design and construction process of high-rise building foundations in urban areas is to ensure the lifelong safety and serviceability of the new and existing buildings in the neighborhood. In order to realize this aim in a cost-optimized manner, the combined pile raft foundation (CPRF) was developed (Katzenbach et al., 2005). For the foundation of high rise buildings with good subsoil, the simplest structure considered is a raft. But when the subsoil near the ground surface has low load-bearing capacity, high-rise structures are often rested on piled foundations.A piled raft and pile group serves similar purposes, but there are essential differences between them. A pile group is a set of piles that have a pile cap. The piles would be designed to share the pile load at ultimate state. The pile cap would be designed to link the piles together but the contribution of the pile cap to bearing capacity will not be included in the design. On the other hand, a piled raft is a foundation, wherein piles are provided along with the raft so that the total load acting is shared partly by the raft and partly by piles, rather than being dominated by the piles (as in a pile group). Piled raft foundations utilize pile support for control of settlements with piles providing most of the stiffness at serviceability loads, and the raft element providing additional capacity at ultimate loading (Poulos, et al., 2011). Therefore, piles are included in a foundation for two main design purposes: to provide adequate bearing capacity and to bring down the settlements to an acceptable level."

Jan 1, 2015

By Kevin Green, Iván Contreras, Aaron Grosser, Jon Ausdemore, Rachel Leier, Amr Ragy

"Construction of a new tailings dam was required to increase tailings storage capacity at a trona mine near Green River, Wyoming. The new dam was founded on overburden soils underlain by both fractured and competent bedrock. The stored tailings and water had high salt content, resulting in salty seepage water. To reduce the impact of the salty water on groundwater and the Green River, the design of the new tailings dam included a 257,260 SF (23,900 m2) seepage cutoff extending into competent rock.An extensive subsurface characterization was performed prior to completing the design and suitable seepage cutoff methods were evaluated. The approach selected was a full replacement panel using hydromill and clamshell for construction and self-hardening slurry (SHS) for the wall material. Laboratory testing was performed and ongoing monitoring has continued to evaluate the hydraulic conductivity and seepage cutoff performance in the briny environment.The paper includes project background, the collaborative approach and outcomes of the QA/QC program, and the monitoring results for the seepage cutoff wall.PROJECT BACKGROUNDCiner Wyoming, LLC (formerly OCI Wyoming, LLC) owns and operates the Big Island Mine facility near Green River, Wyoming. This underground trona mine has produced soda ash since 1962. The Greater Green River Basin covers much of southwestern Wyoming and extends into northeastern Utah and northwestern Colorado. The Ciner facility is located in the Green River Basin, which is part of the Wyoming Basin physiographic province. The Green River runs to the west and the south of the Ciner facility.Beginning in the early 1990s, Ciner primarily disposed tailings underground in mined-out panels. However, in recent years, underground storage has become limited and some disposal has transitioned to the ground surface. Long-term planning revealed a need to expand Ciner’s surface tailings disposal capabilities. Pond 2, a previously permitted disposal area, was identified as the most viable location for a storage facility. The Pond 2 site is directly north of the Ciner plant facilities, northwest of the active Upper Delta tailings storage facility, and northeast of the Green River (Fig 1)."

Jan 1, 2016

By Lewis Stansfield

A rotary displacement method was used to install permanent steel casings for bored piles through an asbestos tip. This method was chosen in preference to alternative driven systems because it was quieter and more versatile if obstructions were encountered. New equipment was designed and made specifically for the project, and stringent health and safety regulations had to be observed.

Jan 1, 2000

By A. Eslami

In recent development of piled raft design, the contribution of both raft and piles to tolerate the loads is taken into account, depending on the stiffness and contributions of involved elements i.e.; piles, raft and surrounding soil. The piles are usually required not to ensure the overall stability of the foundation but to act as settlement reducers. One alternative method of foundation design is therefore to introduce piles purely as a means of improving or enhancing the stiffness of the base soil by structurally disconnecting the piles from the raft. In this paper, two and three dimensional finite element analysis of disconnected pile-raft systems are performed on three case studies including a 12-storey residential building in Iran, a 39-storey twin tower in Indonesia, and the 256m height of Messeturm tower in Frankfurt, Germany. The analysis include different geometrical parameters, e.g., pile spacing and embedment length, arrangement and raft thickness for foundation system to obtain the optimized design functions and to clarify the role of each parameter and method of analysis. The parametric study results and comparison to a few field measurements indicate that by concentrating the piles in the central area of the raft foundation leads to the optimum design with the minimum total length of piles. This achievement can be considered as a criterion for project cost efficiency. On the other hand, disconnected piled-raft systems can significantly reduce the settlements and raft internal bending moments. Finally, the comparison indicates that simple and faster 2D analysis has almost the identical results to 3D analysis which is complicated and time consuming.

Jan 1, 2008

By Alun J. Davies

This paper describes a design-build project for the construction of a tanker wharf for 150,000 dwt vessels. The tankers deliver oil from offshore oil fields to a Transshipment terminal on the south coast of Newfoundland. The project described is an expansion to a previously constructed facility, adding an additional berth. The first berth was designed conventionally as concrete structures supported on groups of independent, single piles. The second berth was awarded to Peter Kiewit Sons' Co. Ltd. based on an alternate design which utilized a "jacket" concept whereby prefabricated steel frames are placed on the seabed and serve as permanent templates and also give lateral support to the piles, thereby increasing their load capacity. This led to economies and time savings. Discussed herein is the design process and the field installation, covering the jackets, driven pipe piles, and the rock anchors.

Jan 1, 2000

By Edmund J. Cardoza

The Detroit Water and Sewerage Department (DWSD) provides water and wastewater services to the Greater Detroit Metropolitan Area. Sewerage is treated at the DWSD Wastewater Treatment Plant (WWTP) located at 9300 W. Jefferson Street south of the City of Detroit, Figure 1. PARTICIPANTS Engineering and design of the project for the DWSD was performed by Harza Engineering Company, Inc., C.C. Johnson & Malhotra, P.C. and their sub-consultants, including Worley Engineering and Wade Trim. The Prime Contractor is a Joint Venture of Traylor Brothers, Inc. and Jay Dee Construction. The shaft drilling and riser installation was performed by The Millgard Corporation in joint venture with the Prime Contractor (MTJD). The selection of specialized drilling equipment and the supervision and performance of the access shaft and riser installations was primarily the responsibility of The Millgard Corporation (TMC).

Jan 1, 2001

By Michel Bustamante

The occasional substandard performances of continuous flight auger in particular soil conditions have prompted the drilling rig manufacturer to improve the standard CFA in order to reduce its negative effects. A real improvement of interest was the launching of the double rotary CFA system. The promising features of the latter have incited the authors to implement an extensive experimental research on pile constructed using this type of technique but in the specific context of cohesive soils. Short-term static load tests were carried out on a total of 9 test piles of various installation techniques in order to compare the respective performances. The promising features of the double rotary CFA have incited the LCPC & Durmeyer Company to implement an extensive experimental research on this type of pile technique but in the specific context of cohesive soils and more particularly in clayey marls. After load tests completion the research has been completed by an excavation of the double rotary CFA piles. All the collected data concerning the implemented program are reported.

Jan 1, 2002

By Kamil Nuzha, Jianchao Li, Bashar S. Qubain

"The Philadelphia Water Department is rehabilitating Belmont Raw Water Basin. As part of this work, a 500-ft long, temporary cofferdam was designed to retain 35 ft of combined water and soil at the western half during the reconstruction of the eastern half. A cofferdam that comprises two integral rows of sheet piles was selected to take advantage of the soil’s weight between the sheet piles for increased stability. To fine tune the design, a geotechnical investigation was carried out to verify the subsurface conditions and, in particular, the top of rock variations along the centerline of the cofferdam. A detailed finite element analysis was performed based on the subsurface findings and incorporating the construction sequence to evaluate the behavior of the cofferdam at the following stages: installation of tie rods to connect to the two rows of sheet piles; partial excavation and installation of tiebacks; complete excavation of the east basin, and demolition of the cofferdam. Inclinometers and survey markers were installed every 100 ft along the cofferdam and were monitored throughout construction. The deformation measurements were in good agreement with the finite element results.INTRODUCTIONThe Philadelphia Water Department (PWD) Belmont Raw Water Basin is located at the intersection of City Line and Belmont Avenues in Philadelphia, PA. The facility actually contains two raw water basins, east and west, separated by an earthen dividing dike. Water leakage at the bottom of the basins and through the dividing dike together with increasing demand for a larger storage capacity dictated the replacement of the wide earthen dike with new narrower concrete structure. The temporary cofferdam was designed for a two-year period to facilitate excavation support, water cutoff, removal of the existing earthen dike and replacing it with a new concrete dike. During this construction sequence, the water level in the west basin had to be maintained at or near its full capacity.Various excavation support systems were considered for this project prior to the selection of a double wall sheet pile cofferdam. Fig. 1 shows a plan view of the cofferdam and the new dividing dike. A typical cross section of the two structures is shown in Fig. 2. Double row sheet pile walls are commonly used as both temporary and permanent retaining systems in open water applications such as construction works, quaywalls, breakwaters and revetments for storing industrial waste as indicated by Ohori, et al. (1984), Ohori et al. (1988), and Khan, et al. (2001). There are many advantages to double row sheet pile systems as recognized by Ohori, et al. (1984; 1988): (1) It can be installed and removed in the presence of water easily and quickly; (2) it provides stability with small width to height ratio, utilizing the existing soils between the installed sheet pile rows; and (3) it serves well as a means for water cutoff. These advantages meet the specific project requirements."

Jan 1, 2016

By Erik M. Westerberg

The Soilex Pile combines a slender shaft, for quick and easy installation, with an enlarged pile toe, for high capacity. The key component is the Expander Body, which is inflated by injecting cement grout when in position. The latest development in the Soilex Pile System results in a reduction of the total cost of Soilex Piles, in many cases values that are competitive with pre­cast concrete piles and displacement piles. Soilex Piles can now be installed on top of a bearing soil layer, instead of 3 to 4 m into that soil as previously required, further minimising the ground disturbance. Soilex Piles achieve high capacity in relatively loose soils, with ultimate loads typically between 1000 and 2000 kN in a sand with CPT qc = 5 to 10 MPa or SPT N= 10 to 20. It is possible to pre-load and proof-load all piles with dynamic testing up to 2000 kN or using built-in jacks, thereby verifying the capacity. The vibratory installation method, which is extremely quick and causes very little soil disturbance and noise, is exemplified by two case histories.

Jan 1, 2000

By Marwa Nabil, Alaa A. Ata

"Recent developments in the analysis of piled rafts has incorporated the load sharing of the raft and the piles to support the superstructure. In the piled-raft system, piles are cast monolithically with the raft and the load is partly transmitted by the raft to the soil directly below it, and partly by the piles to more competent deep soil. While these piles are effective in increasing the bearing capacity and reducing the settlements, they often lead to significant straining actions at the pile head-raft connection which may constitute the weakest link. An attempt to provide a more economical solution, that at the same time overcomes this weak link, is to disconnect the pile heads from the raft and introduce an intermediate cushion of compacted fill. In this case, the piles are considered as reinforcement to the subsoil and will also act as settlement reducers. This paper investigates the load transfers mechanism of the unconnected piled raft with cushion using ABAQUS finite elements Program. The main objective is to provide an in depth analysis of the raft–soil–pile interactions in multi-layered soil under static and seismic loads. The investigated system provides an economical alternative for traditional connected piled raft foundation, where there is no need to reinforce the piles, no need for pile head demolition or expensive waterproofing of the pile head connection. Cost analyses of unconnected versus connected piled raft systems confirmed a cost savings in the construction that may reach from 50 to 70 percent.INTRODUCTIONDesigners around the world have gained more confidence to use the piled-raft as a more realistic system where the raft and the piles share transferring the superstructure loads to shallow and deep soil layers. A further advancement is to use unconnected piled rafts as another practical and economical alternative to the traditional piled rafts. Unconnected piled raft is also synonymous to settlement reducing piles; or simply, soil improvement piles. Liang et al. (2003) has extended the concept of pile-raft-foundation to a new type of foundation called composite piled raft foundation or unconnected piled raft foundation. The foundation is composed of a sand/gravel cushion sandwiched between the raft and piles. The piles group may contain short and long piles. The short piles are constructed of flexible materials such as soil-cement columns or sand-gravel columns, and are used mainly to improve the bearing capacity of shallow soft soil; the long piles, which are made of relatively rigid materials such as concrete, and their main function is to reduce settlements. The cushion plays an important role in mobilizing the bearing capacity of the subsoil and in modifying the load transfer mechanism of the piles. In Shanghai, China, this system of unconnected piled raft has proved to be quite suitable and effective in coastal areas, where deep soft soil deposits exist."

Jan 1, 2016

By C. Dai, S Raathiv

The Waikato Expressway is one of the New Zealand Transport Agency’s (NZTA) seven roads of National Significance. Coffey is part of the City Edge Alliance engaged by NZTA for the Hamilton Section of the project. The 22km Hamilton Section is the largest and most geotechnically complex section of the Expressway. The Mangaonua gully in Sector 6 is the most challenging geotechnical area of the project for piling works. Together Coffey and Brian Perry Civil have carried out the temporary and permanent design and construction of embankments, piling works, retaining walls and soil improvement works for the bridge construction. The design and construction works were governed by weak alluvial layers and artesian pressure layers several meters beneath the ground level. This paper presents the action taken to improve the foundation of temporary platform, control the artesian pressure, prevent bentonite leakages into the highly permeable alluvial layer and challenges in the base grouting process. This paper summarises the key components in the construction and supervision of bored piling works and outlines innovative solutions for challenges which we faced during the construction.

Nov 1, 2022

By Edward Jacobsen, Patrick J. Lydon

"The ongoing expansion of the Oak Creek Power Plant in Oak Creek, Wisc., includes a tunnel bored in rock that connects to four vertical intake shafts approximately 1.5 miles (2.4 km) offshore in Lake Michigan. In 2004, Case Foundation Company was awarded a lump sum contract to install these intake shafts. In spite of delays that shortened the May to September construction season by up to 50%, four shafts and liner assemblies were drilled in 2005 and 2006. The shafts were connected to the tunnel in 2007 by mining upward to reach the lower portion of each liner and then removing its internal bulkheads so that lake water fl owed into the tunnel. The project is one of the largest private construction projects ever undertaken in Wisconsin. The expansion adds 1,230 megawatts of generation. In addition to the tunnel and offshore work, there will be 16 miles (26 km) of railroad track and 6 million cubic yards (4,600,000 m3) of earth work. The 27 ft (8.2 m) diameter tunnel, drilled some 150 ft (46 m) below the surface of Lake Michigan, originates onshore at a pump house. A structural slurry wall was constructed as the foundation for the pump house. The tunnel passes to the south near the current water intake before bearing east toward the new offshore intake shafts, which are 12 ft (3.6 m) diameter by 108 ft (33 m) long steel liner assemblies. These were grouted in place from approximately 3 ft (1 m) above the crown of the intake tunnel and then to 20 ft (6 m) below the lake bottom.Site GeologyOffshore. The plant site is north of the Racine-Milwaukee county line in an area affected by glacial activity. The soil conditions encountered at each shaft location were consistent, with noticeable variations occurring in the top of rock elevations that sloped downward from the innermost to the outermost shaft."

Jan 1, 2008

By Sun Shao Xian

The Port of Shekou is situated at Shenzhen Bay on the east side of the Pearl River estuary. Geological condition of the site is quite complicated. On top of the sea bed, there is a layer of soft silt 8 - 14 m thick. Under the soft silt, there are intercalated layers of sand, silt and clay. Average surface elevation of the underlying undulatory weathered bed rock is about - 20 m, with a variation of about 10 m. In certain locations, the weathered bed rock is covered with a layer of silt 3 - 4 m thick. This paper gives brief account of three types of wharf structures which are of particular interest, constructed in the last few years: (A) Platform type wharf structure with frontal sheet piling and steel raking pile in the rear; (B) Relieving Platform type structure with steel sheet piling and inclined anchoring HP pile ; (C) Steel pipe pile row supported apron added to a marginal quay. Average construction time of a deepwater berth is about six months.

Jan 1, 1991

By Susan Rafalko, Mike Walker, John Sankey, Sherif Aziz, Alex Potter-Weight, Mary Nodine, Frederic Masse

"After several successful projects on the Garden State Parkway and New Jersey Turnpike for support of single-stage MSE (Mechanically Stabilized Earth) walls using rigid inclusions (Controlled Modulus Columns) as an alternate to two-stage MSE walls and surcharge, the Bass River Bridge Widening project presented additional challenges in terms of soil conditions and height of embankment that created opportunities for the design-build ground improvement contractor and its MSE wall-designing partner to enhance their design and construction methods. The specialist contractor decided, in association with the wall system supplier, to perform an independent large scale instrumented test area on the project to demonstrate the ability of the design techniques to model the behavior of the system, as well as the capacity of the rigid inclusions to provide the necessary bearing capacity and settlement control to allow the construction of the highway without any consolidation period. This paper presents a detailed description of the design of the ground improvement system and MSE wall system, as well as the results and conclusions of the monitoring data gathered on the large scale test program. The combination of rigid inclusion ground improvement technologies, such as the CMC system, together with an MSE wall system allows for the rapid and economical construction of high embankment without waiting for a surcharge and consolidation period or the necessity to use a two-stage wall system. In-depth understanding of the design techniques and advantages of this combination will be provided and should be beneficial for any geotechnical engineer or owner looking for innovative solutions to save both time and cost on their projects.1. IntroductionAs development continues on sites with poor ground conditions throughout the world, conventional MSE walls remain a flexible design solution; however, construction of MSE walls in combination with ground improvement is becoming more frequent where extreme differential and/or total settlement prevail due to soft ground conditions. Various techniques have been used in the past in such conditions (e.g. conventional surcharge, staged construction, or two-stage MSE walls), even though these design solutions have typically involved longer waiting times for settlement to occur. As a result, conventional MSE wall design has been combined with a variety of ground improvement techniques consisting of rigid inclusions for an economical and efficient solution with the potential to accelerate construction and limit long term settlement. For the particular subject of this paper, the specialist contractor (Menard) proposed to use CMCs (Controlled Modulus Columns) to support the highest part of the MSE wall. CMCs are grouted displacement rigid inclusions installed in a grid-like pattern using a displacement auger. Before the CMCs are installed, a working platform may first need to be placed to allow equipment to move around the site depending on the ground conditions. Following the CMC ground improvement, an LTP (Load Transfer Platform) is installed prior to the construction of the MSE wall."

Jan 1, 2015

By Hiren J. Shah

The urban environment and geology create unique challenges for design and construction of deep foundations. The effect of these is prominently experienced in New York City. Three such project case histories are presented in this paper. The first project is a multi-use development. Relatively unusual glacial geology was observed at the site during the subsurface investigation phase. This played an important role in the selection of deep foundations as well as during construction. The design and construction aspects of the pile foundations, settlement estimates, a pile drive test program during design, piling equipment and production pile installation are discussed herein. A relatively smaller project is the second case history. A combination of drilled and driven deep foundations was employed in one area of the project due to its unique conditions. In another area of the project, an addition to a structure required the use of supplemental foundations to resist new additional loading. Tight space and load sharing with the existing foundations were important considerations in the design and construction. Finite element modeling of the existing and completed structure was performed which was an interesting aspect of the project. The third project case history involves a very large multi-billion dollar project in which various different types of deep foundation elements were used. The aspects requiring the use of such a variety of types and sizes of deep foundation elements included: geologic conditions, re-use of existing foundations, protection of adjacent infrastructure, construction staging, restricted space, loads, deep excavations, cost and schedule.

Jan 1, 2011

By Gerald Verbeek, Erick Baziw

Dynamic soil analysis (DSA) in geotechnical practice is intimately related to the capability of measuring the necessary soil properties of shear modulus and absorption. In DSA the methods of analysis are based upon the stress-deformation response of soils due to imposed shear strains. Typically the soil profile is numerically modeled as linear visco-elastic system. This technique is referred to as the Equivalent Linear (EL) method, and it requires the specification of the input parameters of low-strain (<10-5) shear modulus, modulus reduction, and the equivalent viscous damping ratio, which is directly related to the soil absorption value. Downhole seismic testing (DST) has proven to be a very accurate tool for estimating low strain shear modulus values as long as source wave raypaths are taken into account, especially for near-surface investigations. DST has also been utilized to estimate low-strain interval absorption values. In these cases standard frequency domain absorption estimation algorithms (such as the spectral ratio technique) are utilized where it is assumed that the source waves are traveling along the same travel path, which is obviously not the case for near surface DST investigations. This paper outlines a unique DST absorption estimation methodology, which is carried out in the time domain and takes into account source wave travel paths. 1. INTRODUCTION There is considerable interest in methods of geotechnical in-situ engineering that provide accurate estimates of the shear wave velocity and the associated absorption values in the ground, since these parameters form the core of mathematical theorems to describe the elasticity/plasticity of soils and they are used to predict the soil response (settlement, liquefaction or failure) to imposed loads (whether from foundations, heavy equipment, earthquakes or explosions).

Jan 1, 2019

By Gyimah Kasali

Rapid Load Testing was performed as part of an extensive drilled pier testing program for the University of California Berkeley Capital Improvement Program. The purpose of the program was to: (1) Verify the axial compressive design capacity values for the planned 24" piers, and to estimate the capacity of the existing 30" CIDH piers, and (2) To evaluate the seismic performance of the proposed drilled shafts. The Fundex PLT was used since the loading period of the PLT is very similar to the period of a seismic event, making it an ideal tool to model the pier response to seismic events. "Performance-based design" of structures subject to seismic loads has been of particular interest to UC Berkeley Seismic Review Committee and the Pacific Earthquake Engineering Research Center. The comparison of static tests to Rapid Load testing also provided valuable correlations. The program represents one of the most comprehensive drilled pier test programs on the West Coast. The testing program consisted of Rapid Load Testing using the Fundex PLT on 6 drilled piers. Rapid Load Tests were followed by conventional static compression and tension tests on selected piers, followed by another cycle of rapid load tests on the statically tested piers. The piers featured extensive instrumentation to allow detailed interpretation of the test result. Correlations were drawn to compare static load test result to that of the PLT in the particular soil profile, and the PLT also provided the data to analyze the ultimate seismic capacity of the piers. The load test results indicate that the ratio of interpreted failure load from the PLT data to the corresponding load from the static load test data is about 1.2 to 1.3 for the clayey soils underlying the test site. The results also indicate that the PLT offers an economical approach to defining the stiffness of drilled pier foundations subjected to seismic loads for use in performance-based design.

Jan 1, 2002

By Trevor I. Addenbrooke

Stress reducing piles were used for the first time at the Queen Elizabeth II Conference Centre near the Palace of Westminster in London, UK. The inclusion of these piles directly beneath heavily loaded columns was to reduce the high anticipated bending stress in the foundation raft, and to eliminate local yield of the London Clay beneath the column locations. Load cells were placed in one of the stress reducing piles during construction. The data showed that the pile carried about 30% of the column load. This can be contrasted with conventional piled raft design where the pile carries upwards of 80% of the column load. The build up of load on the pile and pile displacement have been accurately reproduced using coupled finite element analysis. These numerical results demonstrate the value of geometrically simple axially symmetric analyses for modelling a pile-enhanced raft. On site, excavation preceded construction of the raft and subsequent pile loading. Failure to model this construction sequence caused the shear strength to mobilize at the base of the pile first, during loading, whereas following the construction sequence caused the shear strength to mobilize at the top of the pile first.

Jan 1, 2002

By James P. Stewart

This case history describes the engineering design and construction for the Contractor of a 35-ft-deep excavation for an 800-square-foot addition to an existing sewage pump station. The site posed unexpected geotechnical complications that included deep gravelly soil, a history of local construction difficulties, groundwater consisting of heavy salt brine, and the need to underpin the existing pump station. The project took an interesting twist when the Owner issued a change order limiting the dewatering discharge to a fraction of that required to lower the water table. This documents the interesting circumstances of this job and documents the unusual subsurface conditions in the Syracuse, NY Lakefront area.

Jan 1, 2003

By Raffaella Granta

Mosul Dam is an earth fill dam located on the Tigris River, approximately 40 km (25 mi) northwest of Mosul, Iraq. The construction of the dam was completed in 1984. It is one of the largest multipurpose dams in the Middle East, and the largest dam in Iraq. The dam provides flood control, irrigation, power generation and water supply. At 113 m (371 ft) high and 3.65 km (2.3 mi) long, the reservoir has a storage capacity of 11.1 billion m3 (392 billion ft3) of water. The main hydroelectric power station has four turbines for an installed capacity of 750 MW. The discharge system includes two bottom-outlet tunnels of 10 m (33 ft) diameter, a five-gate service spillway and an emergency fuse plug spillway.

Oct 1, 2022