Search Documents

By Narong Thasnanipan

In Bangkok due to the prevailing condition of subsoil (existence of considerably weak stratum at top part) deep-seated large diameter bored piles of over 50 m depth with 0.8 -1.8m in diameter have been mainly used for heavy structures such as high rise buildings, elevated expressways, flyovers and more recently for underground subway stations of the first Bangkok MRTA system. As a part of pre-planned quality assurance regime and retrospective investigation, integrity of the piles are tested to obtain the information with regard to the potential deficiencies of the constructed piles which may have formed during pile construction process or may have been attributed by other activities after construction of the piles. An overview of three commonly used non-destructive tests such as sonic integrity, sonic logging and high strain dynamic load tests on deep-seated piles in Bangkok subsoil is presented in this paper. Advantages and limitations of each integrity test are discussed.

Jan 1, 2004

By Shaw-Shong Liew

This paper presents the design concept using floating piles to support 2500Ton oil storage tanks on a very soft alluvial clayey soil of about 40m thick in Riau Province of Sumatra, Indonesia. The floating piles of various penetration lengths were designed to support seven numbers of such storage tanks seating on a 20m diameter and 500mm thick reinforced concrete (RC) circular raft. The pile points have been strategically located at the RC raft. Varying pile penetration lengths have been designed to minimize the angular distortion of the thin RC raft and the out-of-plane deflection at the tank edge. Vibrating wire strain gauges were installed at different levels inside the ø350mm prestressed reinforced concrete piles to measure the load transfer profile during the static load tests and water-loading test. The installation and interpretation of the instrumentation are described and discussed. Boreholes, in-situ tests like piezocones, vane shear tests and standard penetration tests, and laboratory testing were carried out to obtain geotechnical parameters for the pile designs. Static load tests were also carried out on the spun piles of varying lengths of 24m, 30m and 36m respectively. It has been demonstrated that the floating pile system can be a cost effective design to support heavy structures on very soft compressible deposits with satisfactory performance. Finally, the design concept validated with the results of instrumentation is discussed.

Jan 1, 2002

By Madan B. Karkee

The understanding and the development of sound theoretical basis concerning the pile foundations has been phenomenal during the past few decades, considering the thousands of years the piles have evidently been in use. The importance of the quality assurance and the need for verification of load bearing capacity is being further reinforced rather than undermined by these developments. This is evidenced by significant developments made in the pile load test technology in recent decades, making it possible to make judicious selection of a test method, or a package of test methods, suitable for a given situation. The selection depends on the objective of carrying out the test and the reliability desired. Presently, the possible selection ranges from dynamic to static methods. The extent of dynamic effect in a test can be reckoned based on a dimensionless parameter defined as the 'relative duration'. Examples of different load tests are given for illustration of the different methods currently in use.

Jan 1, 1997

By Lassaad Hazzar

The ultimate lateral resistance of piles in cohesive soil is studied using the well-known finite difference code, FLAC2D. The Modified Cam Clay (MCC) constitutive relation is adopted in the analyses to model the cohesive soil behavior, whereas the structural pile model with three degree of freedoms, available in FLAC2D library, is adopted to model the piles. The reliability of Broms's method, still used in the current design practice of piles under lateral loads, is verified. Comparisons between the ultimate lateral resistances of piles and those deduced from the graphs proposed by Broms (1964) are presented in graphs. Different factors thought to affect the lateral resistance of piles in cohesive soil, not adequately considered in Broms's method, such as clay stiffness, pile length, pile diameter and axial load are parametrically studied. A special concern is devoted to elucidate the effects of over-consolidation ratio (OCR) on the ultimate lateral resistance of piles in cohesive soil.

Aug 1, 2013

By Harry Schnabel

A 6200 m² cement deep soil mixed (CDSM) wall was constructed for an addition to the Museum of Fine Arts in Boston, Massachusetts. The addition was located along the east side of the existing museum within an existing courtyard and in the area of a recently demolished structure. The basement for the new addition extended up to 9.1 m below the floor slabs of the adjacent buildings. The adjacent buildings are supported on a variety of foundations including; shallow spread footings on alluvial sand deposits, low capacity piles bearing in the alluvial sands and Boston blue clay, and caissons bearing on the alluvial sands and clay. Groundwater was less than one meter below the top of the CDSM wall. The new addition was founded on shallow foundations in the desiccated crust of the Boston Blue Clay. The CDSM wall was selected as the most economical means to control deep seated ground movements, limit movements of adjacent structures, and inhibit groundwater flow into the excavation. Braces and a continuous wale were used to support the CDSM wall where it was located adjacent to structures. Tiebacks were used where there were no structures. Other geotechnical construction at the site included: ? Jet grouting (JG) to improve the ground and provide an impervious subgrade layer at the west end of the addition, ? Concrete pier underpinning was used to support an existing structure on the west end of the site, and ? A secant pile wall using alternating drilled shafts and jet grout columns was used for earth support and a barrier to groundwater flow to allow for the installation of a storage tank at the south end of the site. Inclinometers, total station surveying, vibrating wire strain gauges on the braces and wales and load cells on the tiebacks were used to monitor performance of the excavation support system. The excavation support system performed better than required limiting lateral movements of the adjacent structures to less than 13 mm and vertical settlement to less than 8 mm. No settlements or movement were detected during the construction of the wall. Lateral movement of the CDSM wall was typically below 15 mm with the maximum movement occurring near subgrade.

Jan 1, 2011

By Stephen Buttling

The construction of a water treatment plant in Dandenong, Victoria, required detention tanks and a pumping well. The design provided by the Engineer used conventional rectangular cast-in-situ reinforced concrete walls within a sheet piled cofferdam. It was decided to construct the tank and shaft using the diaphragm walling technique as an alternative and, for the shaft in particular, this involved a “circular wall”. Except where cutters are used, joints in diaphragm walls have to be made between colinear panels, with waterproofing provided by dumb-bell water stops held within trapezoidal forms. This means that the circle has to be approximated by a number of straight sides, which in this case was twelve. The requirement was to design the reinforcement for the strange shaped panels. Finite element analysis was used, in the first stage using an axisymmetric model to determine the profile of lateral earth pressures with depth. In the second stage a horizontal slice was modelled, without gravity which normally operates from the top to the bottom of the page. By considering appropriate possible earth pressures at different depths, a range of bending moments was calculated, which was used by the structural engineers to design the rebar. The tanks were successfully constructed, and inclinometers were installed in both the tank and the shaft. Measured deflection profiles show that the design was moderately conservative.

Nov 1, 2022

By Michael Arnold, Jignyash Manyam, Yoav Rappaport

The USACE required construction of over 13 miles of cutoff wall at an average depth of 65 feet for the Herbert Hoover Dike (HHD). To meet project requirements, to provide quality control and make sound operational decisions, automated data capture, retention and visualization is crucial. Accurate and complete data management allows the authors to deliver critical business insights and to improve operational efficiencies. The author’s understood the necessity of capturing all their data, and efficiently processing and displaying it for multiple stake holders, for both internal and external purposes. The authors realized early in the project life cycle that data ownership and management is one of the fundamental features of the construction process. The authors developed their own software and use two in house applications; WEB-BGM online portal and, b-project which store rig production information combined with field quality control. b-project is used to create and deliver the Enterprise Database (EDB) to the USACE. Another biproduct of capturing the production data is the generation of the Geographic Information Systems (GIS) and also business analytics visual interactive display, developed through Microsoft Power BI. The paper focuses on the business process workflow and various technologies employed and lessons learned from the field operator perspective to achieve higher returns on business software operations.

Oct 1, 2022

By Pancho J. Garza, Keith H. Dahlen, Chris A. Labye

"Design for reconstruction of the East Flagstaff traffic interchange project located in Flagstaff, Arizona posed particular challenges. The proposed design included construction of a nearly 50-foot tall mechanically stabilized earth (MSE) wall given rightof- way constraints and soft subgrade soils. The tight right-of-way, approximately 15 feet in certain locations, adjacent to existing structures limited the number of viable remedial alternatives to provide grade separation at the proposed bridge abutment without significant settlement. Preliminary analyses indicated the existing subgrade soils - consisting primarily of relatively soft silts and clays with decomposed pumice - would settle approximately 12 to 14 inches resulting in unacceptable wall deformation. Stone columns placed via vibratory methods (vibro-replacement) consisting of circular excavations which penetrate to firm bearing soils and which are filled with crushed stone were selected to densify the existing subgrade soils. The implemented mitigation measures helped limit settlement to less than one inch and allow for successful construction of the project. The project history - including site constraints, subsurface conditions, evaluation of remedial alternatives, stone columns methodology, and effectiveness of ground improvements - will be discussed.IntroductionThis paper describes the subsurface investigation performed for the reconstruction of the Business Route 40 (B-40) (Country Club Drive) and United States (US) 89 Traffic Interchange (TI) located within the city limits of Flagstaff, Arizona. This project is currently referred to as the East Flagstaff TI. The Project Site Vicinity Map is shown below.The former B-40/US 89 TI was considered ineffective in handling the current and projected volumes of traffic which transition from northbound (NB) B-40 to US 89 (both directions), as well as from southbound (SB) US 89 to SB B-40. The intent of the project was to reconstruct the TI to better accommodate projected traffic volumes. The project eliminated the existing ramps from both NB B-40 to SB and NB US 89. The new interchange includes a Tee intersection from B-40 to US 89. In order to accommodate this alignment, the profile of US 89 was raised several feet (on nearly the same as existing horizontal alignment) to match the elevated profile of B-40. B-40 was shifted just west of its current alignment to accommodate construction of a new, wider bridge structure which spans over Industrial Drive, the Burlington Northern Santa Fe (BNSF) railway, and old Route 66. South of the new bridge, B-40 transitioned back to the existing alignment just north of the I-40/B-40 TI. Within the project limits, both US 89 and B-40 were widened to three travel lanes in each direction."

Jan 1, 2015

By Kazimierz Gwizdala

In recent years, in Poland the ATLAS piles have been successfully applied for some constructions near Gdansk. The piles have been used as foundations for housing and another areas of civil engineering, in delta Vistula geotechnical region, characterized by weak, highly compressible soils represented by mud and peat, lying in sub-surface layers, several meters thick. Usually below are dense sandy soils or gravel. In all cases, the base of ATLAS piles rested on sandy soils. The analysis of pile bearing capacity has been discussed and verified by static pile load tests (SPLT). The load-settlements characteristics obtained were satisfactory. In the paper, the results of geotechnical investigations as well as calculations and load tests are shown. The ecological aspects of ATLAS piles application within highly urban areas of the cities and complex geotechnical conditions are emphasized.

Jan 1, 2006

By R. G. Horvath

The Statnamic loading test is a new and innovative method for testing deep foundations. The test is relatively inexpensive, quick, easily mobilized, provides for direct measurement of applied load and corresponding displacement, and is capable of very high loading capacities. The long duration of the applied loading, as compared to a dynamic loading test, allows for a straightforward determination of the static behaviour of the foundation tested. A new method of analysis of the Statnamic loading test, the Equilibrium Point Method, is presented. A description is given of the pile-soil model and a demonstration of how the static load-displacement behaviour of deep foundations may be predicted from the Statnamic loading test data. The Equilibrium Point Method of analysis is applied to three types of deep foundations in soils which respond differently to fast loading rates. These case histories, from Canada and the United States, include data from static loading tests for direct comparison, and demonstrate the ability of the Equilibrium Point Method to predict static behaviour of the deep foundations.

Jan 1, 1993

By Xiong Houjin

In the excavation works of some deep foundation pits within the boundaries of Guang­dong Province of China, though some measures, such as steel sheet piles, diaphragm walls, etc. were taken to protect the walls, the construction of the excavation works was often accompanied by damage of buildings and public facilities, surface settelment. sand boil and collapse of piles. When these happened, only chemical grouting could be used as the most efficient measure for rushing to deal with or rescue the emergencies. Besides, the application of chemical grouting protection wall technique also palys a very important role under the geologic conditions of the coastal areas of Guangdong Province, when applied in the mucky oystershell layer wealthy in water and the deep mud layer, it can not only achieve good results, but also reduce the cost significantly. In this paper, we discuss the water-tight and earth retaining functions of chemical grouting protection wall in weak formation, and introduce the applicable ranges of chemical grouting protection wall in the excavation of deep foundation pits. Some technological principles and design considerations of the construction of chemical grouting protection wall are presented. Different types of protection wall are also introduced.

Jan 1, 1991

By Shahid Islam, Lucian Bogdan

Deep and large diameter drilled shafts use mostly bundles of Grade 60 (415 MPa) reinforcing bars as longitudinal reinforcement with rebar splices to make it longer. Lower Grade steel requires large number of bars which result in rebar congestion and difficulty in placing concrete. This leads to increased labor cost for fabrication and installation. By utilizing larger size and higher strength threadbar, the congestion of rebar can be reduced significantly and bundling of bars can be avoided. The lap splices are replaced with simple threaded couplers and end hooks are replaced with end terminators. Threadbar conforms to ASTM A615-15 and can be epoxy coated if required for corrosion protection. This paper describes an attractive value engineering of replacing Grade 60 (415 MPa) bundle of rebars with larger diameter Grade 75 (515 MPa), Grade 80 (550 MPa) and Grade 100 (690 MPa) threaded bars and threaded couplers in some specific drilled shaft projects in the USA. INTRODUCTION A drilled shaft which may also be referred to as drilled piers, caissons, cast-in-drilled-hole piles and bored piles is the key element to the foundation of massive structure. They are used for tall buildings, bridges and foundations for other applications such as retaining walls, sound walls, signs, or high mast lighting. Drilled shaft foundations are typically 3 to 12 feet (0.9m to 3.7m) in diameter cast-in-place deep foundation elements constructed in a drilled hole that is stabilized to allow controlled placement of reinforcing steel and concrete. Drilled shafts for transportation structures are commonly used to depths of up to 200 ft (61m) in the USA. Drilled shafts can be installed in a variety of soil and rock profiles, and are most efficiently utilized where a strong bearing layer is present. The reinforcing cage is typically lowered into position within the hole and then concrete placed through the center of the shaft, flowing from bottom to top through the reinforcement to fill the hole.

Jan 1, 2018

By Boleslaw A. Klosinski

Drilling of a pier hole is accompanied with stress releasing in the surrounding soil and often with loosening of soil at the pier base. In effect the drilled piers are more deformable than driven piles of comparable dimension. The bearing performance of a pier may be considerably improved by properly executed base grouting. Various techniques of base grouting are used; many of them were described by Bruce (1986). The grouting devices are often placed within the pier. Alternatively the soil at or under the base is treated by cement or chemical grout. Preloading of the base subsoil by use of a special grouting cell is considered as the most effective way. Treatment of the ground below pier base with cement or chemical grout may be also useful. It may be performed immediately after the pier construction or during service, as a measure for increasing the pier capacity.

Jan 1, 1995

By Kirk A. Mcintosh

Augered, cast-in-place (ACIP) piles have been utilized in the United States for a wide range of projects since the 1950's. Due to the cast-in-place nature of the installation method (and lack of a driving criteria); however, ACIP piles have not been readily accepted by some practicing geotechnical and structural engineers. Since ACIP piles were initially developed, the installation equipment and techniques have been improved and refined and the number of experienced contractors has significantly increased. Over the past 10 to 15 years, the pile type has experienced significant growth in the United States (particularly in Florida) because engineers have become more knowledgeable and comfortable with its use. The Miami area, in particular, has experienced considerable growth in the utilization of ACIP piles primarily due to their usage on the $1 billion Miami Metrorail System project in the early 1980s. The economic advantages over other deep foundation types, coupled with some unique installation advantages, have shown that ACIP piles can be a viable foundation alternative on many projects. Even though ACIP piles have gained respect in the private sector, the pile type has generally not been readily accepted by government transportation agencies. The reluctance to readily accept this foundation type stems primarily from the quality assurance aspect of cast-in-place pile construction. Additionally, there has not been much research activity on this foundation type, technical papers, formal associations (other than the DFI), or a concerted effort to standardize the industry. This paper serves to discuss the state of practice for ACIP pile installation in the state of Florida.

Jan 1, 1997

By Nick M. Withers, Suthagarann Visvalingam, Cillian Mc Colgan

The level crossings removal project in Victoria is removing 75 level crossings across Melbourne to improve safety by separating trains from traffic, with other benefits such as reduced congestion, an upgraded road network, connected communities and support of urban regeneration. The level crossing at Station Street in Carrum forms part of the scope being delivered by the Southern Program Alliance (SPA), which is delivering level crossing removal works associated with the Frankston Train Line. At Station Street, a rail viaduct consisting of 19 spans and totalling approximately 545 m in length is under construction to remove the former level crossing. The viaduct consists of two parallel reinforced concrete Utrough girders and steel trough girders, one for each rail line. The foundations of the rail viaduct are founded on groups of Continuous Flight Auger (CFA) piles. The characterisation of geological units encountered at Carrum for the foundation design has been based on insitu testing and interpretation of test results from high strain dynamic pile testing (PDA) and Case Pile Wave Analysis Program (CAPWAP) from the Seaford Road Bridge, located approximately three kilometres South of Carrum, in similar ground conditions. By conducting pile load-deformation analyses based on pile testing significant savings were made for the client compared to the original design which was based on more traditional empirical correlations. This paper discusses the pile design methodology adopted using pile test data for this viaduct foundation. The results of this assessment are also compared to existing empirical correlations, and the limitations are discussed. The performance of the adopted pile design methodology using pile test data at Carrum rail viaduct is also discussed.

Nov 1, 2022

By Andreu J. Ferrero

Polyurethane and acrylate resins are routinely injected into soils to gain strength and control water flow. However, most published data regarding strength gain is derived from laboratory samples created under ideal conditions. This study endeavored to inject resins into full scale mock-ups that could then be excavated and tested to yield results comparable to actual field conditions. To achieve this goal, a large container was filled with a silty SAND (SM), as defined by the Unified Soil Classification System (USCS). The soil was moisture treated and compacted in lifts of 0.3m. PVC pipes installed in a diamond grid into the soil were used to inject polyurethane and acrylate resins. Dynamic cone penetrometer (DCP) tests were conducted on the polyurethane treated soils, the acrylate treated soils, and the baseline untreated soils in the container. Testing results will be correlated to SPTn and CBR values to evaluate increases in the soil strength parameters in the treated soils. Cored samples of polyurethane and acrylate treated soils will be tested in compression, shear, and triaxial. These laboratory test results will focus on material property gains for the treated soils, in comparison to standard values for similar soil types. Complete documentation of the soil type, compaction methods, injection methods, and testing performed have been documented and will be presented in the final paper.

By Timothy D. Stark

Jet grouting has increasingly become one of the ground improvement technologies used to address seepage concerns and to provide strength improvement of soils. The technique of jet grouting uses high pressure/velocity jet fluids to erode the existing soil and then to mix the cuttings with cement slurry to form soilcrete. Excess slurry or spoil is ejected to the surface. If the native soil is not completely mixed with slurry, the resulting columns will have soil inclusions which can reduce the strength of the column and/or increase the permeability of the column. A jet grout test program at Tuttle Creek Dam shows that the completed large diameter columns contain perhaps 40 to 50% or more of native soil that was not broken up and mixed during the jet grout process. The test program included excavation of full-scale columns to a depth of 35 ft (10.7 m) for visual inspection and testing. Additionally, six of the columns were cut or sectioned to investigate the interior of the columns. The observed inclusions include significant amounts of both fine grained (silts and clays) and coarse grained (fine sands and sands) soils. Evidence suggests at least two explanations: (1) fine grained soils can be difficult to erode and break up into small enough particles that can be ejected to the surface, especially if at low natural water content, and (2) when large diameter columns are being excavated, the excavated roof of the cylindrical cavity may be unstable and may collapse. With this roof instability large slabs of material can break off, fall into the slurry and escape the cutting and mixing action of the rotating jets. This paper describes the Tuttle Creek Dam test program, inclusions observed in the completed columns, and suggests potential causes of the inclusions.

Jan 1, 2009

By Charles M. Wilk, Lori Tiefenthaler

"Information presented in this paper can be used to support deep soil mixing, subsurface grouting and slurry wall technology as sustainable construction technologies. Ordinary Portland Cement (OPC) is the default cementitious material used by Deep Foundation Institute (DFI) Members for geotechnical work. Owners, engineers and contractors can contribute to the sustainability of a geotechnical project by increasing the use blended hydraulic cements and industrial byproducts to replace some of the OPC in mix designs. Sustainability is defined as the quality of not being harmful to the environment or depleting natural resources. Production of cementitious materials consumes natural raw materials and energy while also generating air emissions and waste. Life Cycle Assessments can be used to compare the relative environmental impacts of one cementitious material to another. Blended hydraulic cements (BHCs) are interground (or blended) mixtures of Supplementary Cementitious Materials (SCMs) with OPC. Commonly used SCMs include fly ash, ground granulated blast furnace slag (GGBFS) and limestone. Examples of industrial byproducts commonly used in geotechnical work include coal combustion residuals (CCR) (aka fly ash), and ground granulated blast furnace slag (GGBFS). Much of life cycle impact of these SCMs and industrial byproducts have already been borne by the industries that generated them. There is increasing awareness to LCA and sustainability of different materials used on projects. This is evident in the application of the Leadership in Energy and Environmental Design (LEED) program. The savings in environmental impact with the use of SCMs and industrial byproducts can make proposed use of these materials in a geotechnical project more attractive in terms of sustainability. This paper presents (a) information that compares published life cycle assessment data of OPC, BHCs, and slag cement (SC) to illustrate the potential benefits to sustainability and (b) general strategies for positioning a geotechnical application, use, project design or cementitious material mix as a more sustainable alternative"

Jan 1, 2017

By M. England

Keywords: Bi-directional tests, Osterberg cell, O-cell®, static load tests, Timeset® Static load testing, where loads are applied vertically to the top of the pile and often referred to as 'top down testing', has been used for many years and has become a 'standard' test for the world of foundation engineering. The method, although well developed, cannot be used under certain circumstances, magnitude of load being a particular issue. There is a finite limit to the load capacity that can be applied with either kentledge, the use of reaction piles or anchors, and as the loads increase, the costs escalate dramatically. A novel test method seeks to overcome all the associated problems of large scale and restrictive area "top down testing", utilising static load testing techniques. The method requires the foundation element to be divided into two or more sections and these can be loaded axially as required using a portion of the foundation element as a reaction. This paper presents some recent applications and developments in the use and application of the bi-directional testing technique using the Osterberg Cell or O-cell® and outlines some of the many advantages of the system. Recent bi-directional test loads applied to bored piles have mobilised capacities of 279 MN and with flight auger piles up to 25 MN.

Jan 1, 2006

By Abolfazl Eslami, Samieh Rezazadeh

"Semi-Deep skirted foundations are considered to be a viable option for a variety of onshore and offshore applications. It is necessary to determine appropriate foundation configurations that allow loads to be transferred safely to the surrounding soil. For this purpose the bearing capacity and stability analyses subjected to combined vertical, horizontal and moment loadings must be found. In this paper the vertical undrained bearing capacity is estimated via finite element analyses. The circular skirted foundations with different geometries considering embedment depth (embedment ratio between 0-2) and size effects (diameter equals to 5, 10, and 20) have been studied. Stress field, kinematic mechanism accompanying failure and bearing capacity factors for total, end and shaft resistance in semi-deep foundations with various embedment ratios are investigated. Furthermore, two probable mechanisms i.e. internal flow and soil plug for estimating foundation capacity for design purpose in practice have been assessed. Comparisons with different research works including conventional methods, upper and lower bound approaches, and finite element analyses have indicated that the conventional methods underestimate the bearing capacity due to ignoring the significant role of shaft resistance. Determining appropriate economic foundation configurations to transfer loads safely to the surrounding soil is a major issue in geotechnical engineering. Shape and dimension of foundations, embedment depth, soil characteristics and applied loading, all affect the foundation performance. Recent studies have shown that for foundations with large breadth and of D/B between 1 to 4, kinematic mechanisms and failure modes are different from the two main types of foundation (i.e. shallow and deep). Therefore, D/B factor must not be considered as the only factor for defining foundation type. ""Semi-Deep foundations"" are another foundation category distinguished based on their performance. This relatively new concept is becoming increasingly an optimum alternative for shallow and deep foundations to support structures especially in accessible depth. As illustrated in ""Fig. 1"", different types of semi-deep foundations consist of:"

Jan 1, 2017