Search Documents

By Thomas G. Tavernaro, Jeffrey A. Schaefer

"The $106 million Olmsted Approach Walls Project, completed in the spring of 2004 by Massman Construction Co., Kansas City, MO, is one phase of a new $1.4 billion Corps of Engineers locks and dam facility located at Mile 964 on the Ohio River, approximately 17 miles (27.4 km) upstream of its mouth at the Mississippi River. When completed, the Olmsted Locks and Dam (Figure 1) facility will replace two aging locks and dams (Locks and Dams 52 & 53) built in the 1920’s, and produce an estimated $600 million annual economic benefit to the nation through reduced lockage time and operation and maintenance costs. PROJECT OVERVIEWThe Olmsted Approach Walls Project consisted of “in-the- wet” construction of four fixed nose pier structures, four floating concrete approach walls, one fixed wall and related underwater excavation, grading and stone placement. Over 12,000 tons (11,000 tonnes) of structural steel and pre-cast concrete elements, up to 335 tons (304 tonnes) in weight, were safely erected during the project.To support these massive structures, the Louisville District of the U.S. Army Corps of Engineers teamed with INCA Engineers, Inc., Bellevue, WA to design thirty seven 10’ (3m) diameter shafts (cast-in-place steel-shell piles) capable of maintaining elastic behavior below ground while resisting barge impact loads, extreme head-on collisions from runaway tows, and environmental forces from river current, wind, and seismic events.The shafts (typically 150’ (45.7m) in length) were founded 100’ (30m) into the riverbed through alluvium, a very consolidated fine sand and clay Cretaceous soil, and finally into a hydrothermally altered rock. Thirty seven shafts were installed under open river conditions at the site, a group of four shafts at each nose pier-pylon location (Figure 2), and 21 at the fixed land wall. Due to difficulty in achieving the required casing tip elevation the team developed a design modification that was successfully implemented for 27 of the shafts.Concurrent with the work at Olmsted, eleven pontoon segments for the four floating approach walls were constructed at a graving yard in Paducah, KY, developed by Massman Construction Company specifically for the project. While the pontoon geometry varied, the pontoons averaged 350’ (107m) in length, 40’ (12.2m) in width and weighed 4,500 tons (4,082 tonnes). The longest of the four walls, at 1,700’ (518m) was comprised of five interconnected pontoons."

Jan 1, 2006

By R. Radhakrishnan, C. Gunasekaran

"Calicut Bypass Phase-II project included construction of 7 m high embankment over soft compressible clays up to 18 m in thickness. Approx 1.5 km length of road out of a total 5 km length consisted of abandoned paddy fields which were low lying, waterlogged and marshy in nature. On the basis of excellent results achieved in earlier phases of the by-pass construction, ground improvement work by installing pre-fabricated vertical drains (PVD) was undertaken to stabilize the embankment foundation along the weak clay areas prior to road pavement construction to avoid large post construction settlement as well as to improve the lateral stability during and after embankment construction. This project perhaps stands out as one of the highway projects completed within a very short time period of total 18 months including four month long heavy monsoon period, when embankment construction was not possible and construction of two bridges across rivers. All activities including the ground improvement had to be programmed and completed within the shortest time period possible. The paper discusses details of the extensive ground improvement and soil instrumentation carried out for the project and will illustrate how careful planning and execution can reduce the period required for highway projects involving ground improvement.INTRODUCTIONPhase-II construction of Calicut by-pass was undertaken on a priority basis by the State of Kerala in 2014. The main contract was awarded to M/S ULCCS Ltd, Kozhikode, Kerala and the ground improvement work was awarded to M/S Geo-Enviro Engineers P Ltd, as specialist agency to design and execute the work.Soil investigation carried out confirmed thick soft clay deposits below GL in three areas along the road alignment totaling approx 1.5 km in length. These areas were low lying, waterlogged and marshy in nature. Highway embankment had to be constructed up to 7 m in height above existing GL to form the proposed road alignment along these areas. On the basis of excellent results achieved in earlier phases of the by-pass construction using pre-fabricated vertical drains or PVD (R. Radhakrishnan, 2006), ground improvement using PVD had been included in the contract to stabilize the embankment foundation along the weak clay areas prior to highway embankment construction to avoid large post construction settlement as well as to improve lateral stability during its construction."

Jan 1, 2015

By Federico Pagliacci, Claudio Asioli, Marco Chiarabelli

"""Rigid inclusions"" are a consolidation method that provides improvement of soft soils thanks to the installation of cylindrical columns made up of a material with significant and permanent cohesive properties, whose stiffness is 500÷5000 times greater than the surrounding natural soil’s. ""Rigid inclusions"" find their application in marginal areas (reclamations, polluted sites) to ensure stability of adjacent structures during construction of new buildings and to reduce the impact of natural disasters (liquefaction in the event of earthquakes, embankment collapse in the event of floods). This paper analyses the “rigid inclusion” construction method, related materials and equipment. Moreover, two performed projects will be illustrated. The first is the restoration of Lungarno Torrigiani Embankment in Florence, Italy. In May 2016, the Torrigiani embankment underwent a structural collapse causing a 3 m. displacement of the riverbank towards the Arno River. “Rigid inclusions” (with 300 mm diameter) have been used to re-compact the loose soil and create a stable working platform for the equipment. The second project illustrates the use of “rigid inclusions” (800 mm diameter and maximum depth of 36.6 m) to control the settlement of a new automatic cold store (30 m high with a 65 x 120 m foot print) for fresh frozen vegetables.RIGID INCLUSIONSIn general, the word ""inclusions"" means a type of consolidation that improves the strength of a soil mass through the inclusion of elements constituted by a material having better characteristics than those of the surrounding natural ground, to improve the overall mechanical characteristics of the treated soil. Inclusions are ""rigid"" when the material introduced into the ground has significant and permanent cohesive properties (concrete or cement mortar) and a significantly higher stiffness (500 ÷ 5000 times) than that of the surrounding natural ground.Typically, medium-small diameters (from 300 to 800mm) with low percentages of treatment (from 2% to 10% of the volume of soil) are employed, ensuring a high quality and consistency of the obtained product, both in terms of diameters and elastic modulus.According to the scope of the project and in urban areas, ""rigid inclusion"" columns can also be performed by means of small diameter drilling rigs (micropiles), weighing less than 20-25 tonnes."

Jan 1, 2017

By Arpana P. Sabu, Themis Vaxevanis, Sissy Nikolaou, Guillermo Diaz-Fanas

Geo-failures from extreme events (landslides, wild fires, earthquakes, floods, etc.) have increased exponentially in recent years around the world and within the USA. When catastrophic failures occur, they usually involve hundreds of fatalities especially in cases of unexpected triggering events, such as large intensity earthquakes or heavy flash floods. Protective actions against identified potential geohazards can mitigate the associated risks and the future occurrences and prevent these occurrences from becoming disasters, targeting the essence of resilience in geotechnical engineering. Imaging and other virtual design and construction tools can be used to identify weaknesses that trigger geohazards and can, in combination with numerical simulations, guide decision making. In spatially distributed problems, 3D visualization and LiDAR-type of technologies are essential in providing geotechnical engineers a deeper understanding of precarious soil zones and support finding appropriate solutions. This paper will present the value of using virtual design and construction technologies though the case study of the Iztapalapa suburb of Mexico, about 20 km southeast of Mexico City. Iztapalapa was developed within irregular topography and has a long history of severe soil subsidence. Following the 2017 Puebla-Morelos earthquake, the town experienced large settlements resulting in extensive damage to the already frail buildings and unregulated infrastructure. The soil subsidence was visualized by mapping available historic and geotechnical data. The visualization helped to identify areas where additional investigations were needed. Additionally, this paper presents a case study of a series of landslides from the 2016 Mw7.8 Muisne Ecuador Earthquake, which demonstrates the advantages of using novel technologies to collect data and create cloud datasets from drones and digital photos to understand and evaluate geo-vulnerabilities in anticipation of an extreme event and during rapid reconnaissance to plan for long-term instrumentation, which can enhance geo-disaster prevention and overall community resilience. INTRODUCTION Iztapalapa is a southeastern borough of Mexico City (CDMX) located within the Mexico Basin (Figure 1). This borough is a densely populated area of CDMX with a total of 1.8 million inhabitants, and has a third of its population living in poverty (Gonzalez-Hernandez et al., 2015) with limited to no access to clean drinking water. Iztapalapa also suffers from high rates of crime, drug trafficking, sex trade and illegal buildings. As the population continues to grow, the already non-regulated and fatigued infrastructure is unable to meet the community needs, especially during and after natural hazard occurrences. The region of CDMX is one of the world’s most seismically active regions that is also exposed to other geo-hazards such as floods, volcanic eruptions, and continuous settlement due to water pumping that has reached 11 meters over the past 100 years (Nikolaou et al, 2019). While the soil subsidence alone has caused significant infrastructure damage in Iztapalapa and throughout the rest of the city, recent earthquakes have also contributed to those damages.

Jan 1, 2019

By George Burke

Of the three projects, particularly the extensive Nimitz II (downtown) project, a single system, which was part of the operation, was used to control the spoil. Spoil control was continuous with the work since a vacuum truck and crew was used to suck up the spoils as they came out of the borehole. So, the whole job was kept clean both during operations and at the end of the shifts. On the Sand Island project, a double system was used. Larger spoil quantities were contained within the shaft limits during the work and the cleanup or disposal of the spoils was performed during excavation.

Feb 10, 2003

By Zhou Haizuo, Diao Yu, Zheng Gang

"The conventional design method for the embankment supported by DM columns usually assumes the simultaneous failure of all the columns. However, the progressive failure may occur in practice, especially considering that many researches have justified the critical load of DM columns is bending moment. In this study, a finite difference method was adopted to simulate the embankment on soft clay improved by DM columns. An increasing surcharge was applied on the embankment surface to investigate the mechanism of the progressive failure of columns beneath embankment. To capture the brittle bending failure of the DM columns, the model employed a cut-off method, in which the column was separated on failed section as long as the ultimate bending failure was reached. Furthermore, high-strength DM columns were used to enhance the global stability of embankment in this study. The numerical results showed that the ultimate bending failure was first reached at the column beneath embankment toe, and then a continuous collapse extended to the column beneath the embankment shoulder. It is found that the reinforcement could be obviously effective when the reinforced area of high-strength DM columns was extended to a certain area.INTRODUCTIONDeep mixed (DM) columns have been commonly used as a soil-improvement technique to increase stability and to reduce settlement of embankment. Research on failure modes of DM columns owing to embankment fill and surcharge has been the subject of interest for a number of investigators (Miyake 1991; Kitazume 2000; Han 2005; 2006).The potential failure modes of DM column include bending, inclination, shearing, rotating, soil flowing and a combination of these modes (Kitazume and Terashi 1991; Broms 1999). Many researchers have found that bending failure of DM columns was more critical than the shear failure. A centrifuge test was performed by Kitazume (2000) and the results showed that the columns failed in bending before shear failure. In addition, several numerical computations illustrated that design method using the shear strength overestimated the stability of embankment over DM columns (Han and Huang 2005; 2006; Navin 2006; Liu 2007; Wang 1996). In practice, an equivalent shear strength method based on bending failure could better reflect the stability of embankment (Zheng 2010; China Code JGJ79-2011)."

Jan 1, 2015

By Bruno Vingiani, Alessandro Bertero

"The use of Artificial Ground Freezing (AGF) for temporary soil strengthening and seepage control is an effective alternative to grouting when dealing with soils whose degree of finesses would imply the use of highly expensive chemical grouts. However, compared to grouting, the application of this improvement technique usually needs a more accurate preliminary soil investigation campaign and a design assisted by specific calculation software. Besides a general description of the main features of this technique, the paper will describe a recent application of AGF carried out in Rome to underpass an existing metro station.INTRODUCTIONNatural ground freezing occurs seasonally or permanently (permafrost) in some areas of the globe close to the poles and can negatively affect the engineering performance of underground structures. On the other hand, Artificial Ground Freezing (AGF) is man-made controllable freezing process that can be used in foundation engineering to temporarily strengthen the ground and create a barrier to the passage of groundwater. During the process, the heat is extracted from the soil in a cylindrical shape around a number of freezing pipes installed into the ground. This action produces columns of frozen soil, which expand gradually till they merge and create continuous frozen wall. The thickness of this barrier can be regulated according to the specific project requirements. Nowadays, AGF technique is applied to a wide range of foundation engineering problems where soil stability and groundwater flows are an issue (Pimentel et al. 2011, Haß and Schäfers, 2013). Typical applications include the temporary stabilization and waterproof of the ground around the excavation profile of mined tunnels until the construction of the final lining (Figure 1).The case history described in this paper deals with a recent application of AGF carried out during the construction of metro Line “C” in Rome. Specifically, this technique has been applied to allow the construction of two single-track mined tunnels running underneath an existing metro station belonging to Line “A”. In that case, the AGF has been evaluated by the Designers as the only possible solution for improving the mechanical and hydraulic characteristics"

Jan 1, 1900

By John P. Turner, Benjamin J. Turner

"Non-destructive testing and evaluation (NDT/NDE) methods have become standard tools as part of the post-construction quality assurance of drilled shaft foundations. In responding to anomalies, foundation designers, owners, and contractors face a number of choices, including: (i) acceptance of a shaft with known anomalies, (ii) further investigations of integrity (e.g., concrete coring), (iii) repair schemes, and (iv) reject and replace. To assist in selecting the best option, analyses are often performed that involve assessing the structural performance of reinforced concrete shafts that may include defective concrete or voids. Currently, the analytical tools for predicting the flexural strength and stiffness of drilled shafts with defective concrete located in discrete regions of the cross section are limited. This paper presents a robust moment-curvature analysis tool for drilled shafts based on the fiber-element discretization method. The tool allows for consideration of anomalous or defective concrete regions in the shape and location that they are believed to exist in the shaft while considering explicitly the nonlinear material behavior of the intact regions based on expected material properties. A case study is used to illustrate the practical application of the analysis to drilled shaft projects.INTRODUCTIONImperfections such as defective concrete or accidental eccentricity of reinforcing cages are an inherent part of the drilled shaft construction process that will occur occasionally even when construction best-practices are followed. Petek et al. (2002), O’Neill and Sarhan (2004), Poulos (2005), and others have described the effects that construction defects can have on the axial and lateral performance of drilled shafts. Our industry has seen rapid progress in recent years in the development and improvement of tools for detecting drilled shaft anomalies, such as gamma-gamma and crosshole-sonic logging, sonic-echo testing, thermal integrity profiling, and even visual inspection with invasive video cameras. Nonetheless, in most cases the wealth of data from these tests is used by foundation engineers to make a fairly “black or white” decision—should the defects be repaired, or should the shaft be rejected? A third option that is not typically considered is to directly analyze the section, including anomalies, and compare the reduced strength and/or ductility to the actual project demands. This option takes full advantage of the data collected during integrity testing, and may provide a justifiable means for avoiding further construction costs and delays, whether for repair or replacement."

Jan 1, 2016

By Aaron Evans, Chu E. Ho, Tom Richards

"This paper describes an innovative case history of using jet grouting to form a groundwater cutoff wall at the interface of a cut-and-cover construction and an existing tunnel. The design of the jet grouting layout was complicated by the presence of a left-in-place bulkhead of unknown dimensions abandoned by previous construction of the existing tunnel. Jet grouting was performed through predrilled holes within the narrow space between the existing bulkhead sheeting and tunnel structure. A systematic sequence of primary and secondary jet grout elements of varying diameters and panel lengths was executed to achieve an effective groundwater barrier. A key challenge in the jet grout design was the impact of potential deviations due to shadowing effects of the left-in-place bulkhead sheeting and pre-formed jet grout columns, as well as overbreak concrete in adjacent secant pile walls. The flexibility of the jet grouting methodology enabled a wide range of operational parameter combinations to be performed, allowing column diameters to be adjusted based on actual field installation measurements. Special precaution was exercised when grouting at critical locations to avoid over-pressurization and damage to the existing tunnel structure.IntroductionThe 96th Street Station box for the new Second Avenue Subway Line in Manhattan, New York included a transition tunnel, which connected the station to an existing tunnel built in the early 1970s (Figure 1). The new station and transition tunnel were both constructed using the cut-and-cover technique with bottom-up sequence (Aksman et al. 2012, Grigson et al. 2016). The main station structure incorporated permanent diaphragm walls for most of its length, except for the southern segment where high rock levels were encountered and the station box was constructed within temporary secant pile walls socketed into the rock. The permanent diaphragm walls were also utilized for temporary excavation support (Ho and Hu 2014). At the northern end of the site, the new transition tunnel was constructed within temporary secant pile walls that extended from the station diaphragm walls to the existing tunnel at the tie-in location. A temporary traffic deck spanning 60ft across the secant pile and diaphragm walls along the full excavated length of the site allowed traffic to continue operating at street level while construction of the station and transition tunnel progressed below grade."

Jan 1, 2016

By David B. Paul

"ABSTRACTThe US Army Corps of Engineers (USACE) has 704 dams in their inventory and over 100,000 miles of levees with a capital value of over $150 billion. Currently, there are 319 dams that are classified as high hazard and have actionable failure modes that will require structural modifications. The most frequent actionable failure mode associated with the inventory is seepage and piping. One of the most effective engineering solutions is the installation of a cutoff to limit seepage. Currently, USACE has over $1.5 Billion of cutoff wall projects under construction and/or design. Given the magnitude of the dam and levee safety issues, USACE is developing a new Engineering Manual (EM) titled “Seepage Control Cutoffs for Dams and Levees.” This EM covers all of the methods to construct cutoff walls. USACE has partnered with the Deep Foundation Institute (DFI) in preparation of the EM to ensure that it is comprehensive and draws from the expertise of the specialty foundation engineering companies that design, manufacture, and construct seepage control cutoffs around the world. The EM contains case histories as well as a comprehensive project statistical summary and guide specification paragraphs. The goal of USACE was to make the EM a state of the art document for use by Districts.HISTORYSlurry wall construction techniques were developed in the late 1940’s in Italy by ICOS. The first use of the slurry trench method of construction in the United States was by the USACE Memphis District in September 1945, to form a partial cutoff along the Mississippi River levee on the Arkansas side of the river just below Memphis, Tennessee. The idea for the project probably evolved from the use at that time of puddle clay trench cutoffs combined with the use of drilling mud for advancing borings. A paddle wheel mixing device was constructed for making slurry from native clays. Trenches were dug to a 20-ft depth using a trenching machine and to a 35-ft depth using a dragline with a 100-ft boom and 2-cu-yd bucket. Backfill was mixed in windrows at the site from hauled-in clay gravel and native materials and pushed into the trench by a bulldozer when the length of the trench was equal to about twice the trench depth. It is amazing that after almost 70 years, the technique is still about the same as it was when first developed by the Memphis District. A soilbentonite cutoff was constructed under the Kennewick Levee adjacent to the Columbia River as part of the McNary Dam Project in Washington by the Walla Walla District in 1952 The first application of a soil-bentonite slurry trench cutoff for control of underseepage at a major earth dam was at Wanapum Dam on the Columbia River in Washington in 1959.The first cement- bentonite cutoff in the United States was constructed at the Tilden Tailings Project to store tailings from the Tilden Mine in Michigan in 1976. The first cement-bentonite cutoff constructed at a dam on a river retaining a reservoir in the United States was completed in 1978 at the Elgo Dam (formerly the San Carlos Dam) in Arizona.The USACE has designed and constructed some of the deepest and most complex cutoff walls for dams since the 1970’s. The first major concrete panel cutoff wall constructed in a dam in the United States was at Wolf Creek Dam (Nashville District) by the ICOS Corporation between 1974-77. The dam has a long history of seepage issues associated with the karst geology that comprises the foundation. In 1968, about 17 years after first being impounded, wet areas, muddy flows in the tailrace and sinkholes in the downstream toe adjacent to the switchyard occurred."

Jan 1, 2014

By Jesus Gomez, Mary Nodine

Rigid inclusions are widely used in the U.S. as a ground improvement tech- nique, particularly for industrial, low- rise and highway applications with poor subsurface conditions, where control of settlement is necessary. Rigid inclu- sions consist of grouted or concrete elements typically 12-24 in (305-610 mm) in diameter that may or may not be reinforced with a center bar. Typical soil conditions where rigid inclusions are feasible might consist of a surface layer of fill and natural, granular soil, followed by a stratum of soft silt or clay overlying a dense or stiff formation. Rigid inclusions are installed from the existing ground surface or suitable work platform, through the surface soils and through the soft, compressible layer, and into the deeper layer, which is less susceptible to compression- induced settlement. Typically, when used to support an extended area surcharge, the inclusions are installed in a rectangular or triangular pattern at regular spacings ranging from 5-12 ft (1.54 m), depending on a variety of factors. The rigid inclusion system is often capped with a load transfer platform (LTP), whose function is to direct a significant portion of the applied load toward the rigid inclu- sions. Additional load is transferred to the rigid inclusions through the upper fill soils above the compressible layer. The rigid inclusions transfer the applied load axially to their tips and into the deeper layer. In the U.S., rigid inclusions are mostly installed using displacement auger systems. The use of a dis- placement auger has significant advantages. It produces zero to near- zero spoils, which is an important environmental consideration. The

May 1, 2023

By Bill Paparis

The thirty year old wharf structures at the Port Authority of New York & New Jersey?s Port Elizabeth Marine Terminal are being modernized for the next generation of Post-Panamax container ships, which require deeper water and larger container cranes. The terminal operator is upgrading the wharf in order to remain competitive, now and into the future. The upgrade coincides with the Army Corps of Engineers? $733 million project to deepen the main shipping channel in New York Harbor. This paper focuses on the structural modifications to accommodate berth deepening and to support the heavier loads of the new cranes. An overview is provided of the design and actual construction, including typical problems encountered when combining new and existing structures. The wharf improvements included: ? Installation of a steel king pile/sheet pile cutoff wall along the face of the wharf to permit increasing the depth from ?12.2 m + 0.61 m to ?15.2 m + 0.61 m ( ?40 ft + 2 ft to ?50 ft + 2 ft) ? Removal of the existing crane rail support beams and installation of new piles and beams to support the increased crane loads ? Replacement of the existing timber fender system with a new system capable of resisting the berthing energy of a 152,000 MT displacement vessel, and having dedicated sections for berthing barges ? Replacing the existing overhead, landside crane electric feeder system with a waterside, cable reel trench system. The work included upgrading the transformer capacity at the terminal for increased crane power demands This paper provides a case history for port administrators, terminal operators, engineers, and shipping lines challenged with upgrading aging terminals.

Jan 1, 2013

By Hyung-Min Kwon

There are a number of methods available that can be used to estimate the bearing capacity of piles that are subject to lateral load, such as the theory of subgrade reaction or the elastic continuum approach. The objective of these approaches is to determine the lateral load corresponding to the allowable lateral displacement of the pile. It is important to select the appropriate soil stiffness when analyzing soil behavior within the allowable displacement of piles because the stiffness of soil is dependent on the displacement of piles. Even though pressuremeter tests can measure the stress-strain behavior within a wide strain range, pressuremeter test results have been utilized to assess only the fragmentary soil modulus based on either semi-empirical correlations or analytical approaches. This study is concerned with a methodology that can estimate the horizontal deformational property, while taking into consideration the nonlinear deformational characteristics of sandy soils. Pressuremeter tests were conducted for 15 cases using a calibration chamber. Reloading curves were employed in the estimation of horizontal deformational property in order to minimize the effect of soil disturbance caused by the installation of the probe. The shear modulus degradation characteristics were estimated from the curve fitting for the reloading curve and from extrapolation using the exponential function. In addition, the difference was taken into account between the stress state around the probe in reloading and that of the in-situ state. A consistent relationship was observed between the maximum shear modulus taken from the suggested method and the bender element tests performed in the calibration chamber, simultaneously with the pressuremeter tests. In addition, the results showed significant concurrence with the well-known empirical correlation.

Jan 1, 2008

By Andrew J. Ciancia

The construction of the Pennsylvania Station in Manhattan, the Beaux-Arts masterpiece, was completed in 1910. In financial ruin, the Pennsylvania Railroad Company sold the station in the 1960?s and the new Madison Square Garden and the Penn Plaza complex were constructed at the site. The demolition of Pennsylvania Station brought public awareness and outcry to protect historic structures and the Landmarks Preservation Commission (LPC) was subsequently established in 1965. In the 1960?s relatively little engineering data was available on the performance of historic structures during adjacent construction and thus, no published criteria were established by the LPC on allowable movements and vibrations. During the late 1970?s a commercial tower was planned adjacent to the landmark Fraunces Tavern Block (FTB) in lower Manhattan. Through negotiations between the LPC and the developer, Dr. M. I. Esrig and the author were retained to monitor the historic block during foundation construction. The monitoring data and building performance compiled from the project formed the basis of the published 1981 ASCE technical paper by Esrig and Ciancia entitled ?The Avoidance of Damage to Historic Structures Resulting from Adjacent Construction?. Based on the ASCE paper, the NYC Department of Buildings adopted Technical Policy and Procedure Notice #10/88 entitled ?Procedures for the Avoidance of Damage to Historic Structures Resulting from Adjacent Construction When Subject to Controlled Inspection by Section 27-724 and for Any Existing Structure Designated by the Commissioner?, June 1988. This paper describes the author?s recent experience during the installation of deep foundations within, or adjacent to, three Manhattan landmark structures. Discussions are provided on the foundation construction, monitoring programs and performances of the three structures.

Jan 1, 2008

By J. Hamada, K. Yamashita, Y. Shigeno, T. Tanikawa

"This paper offers a case history of piled raft foundation in soft ground supporting a twelve-story building in Tokyo. To increase bearing capacity of the soft soil as well as a countermeasure of liquefaction, grid-form deep cement mixing walls (DMWs) were employed with the piled raft. Based on the long-term monitoring results, the ratio of the load carried by the DMWs to the effective structure load after the construction of the raft was estimated to be 0.3 while that carried by the piles was 0.7. In order to clarify the contribution of the DMWs to bearing the structure load, numerical simulation of the settlement and the load sharing among the piles, the DMWs and the unstabilized soil was performed using a three-dimensional finite element model. The results of the numerical simulation agreed well with the measured values, when the Young’s modulus of the DMWs obtained from the unconfined compressive tests was adopted and the shear modulus of the soft soil was reduced to 50% of that at small strains.INTRODUCTIONIn recent years, piled raft foundations have been used in many countries as building foundations. The effectiveness of piled rafts in reducing average and differential settlements has been confirmed not only on favorable ground conditions as shown by Katzenbach et al. (2000), Poulos (2001) and Mandolini et al. (2005), but also on unfavorable ground conditions such as soft clay and/or liquefiable sand using ground improvement technique (Yamashita et al., 2011a; Yamashita et al., 2011b; Yamashita et al. 2013). Grid type ground improvement using the Deep Mixing Method has been applied to sandy ground as a countermeasure of liquefaction to increase liquefaction resistance of unstabilized soil left in the grid walls where its shear deformation during seismic motion is reduced by the confinement effect of the grid walls (Kitazume, 2013). The high applicability of the method was demonstrated in the 1995 Hyogoken-Nambu earthquake and the 2011 off the Pacific coast of Tohoku Earthquake (Tokimatsu et al., 1996; Uchida et al., 2012a; Uchida et al., 2012b).This paper offers a case history of piled raft foundation in soft ground supporting a twelve-story building in Tokyo. To increase bearing capacity of the soft soil as well as a countermeasure of liquefaction, grid-form deep cement mixing walls (DMWs) were employed with the piled raft. First, the results of long-term field monitoring on the settlement and the load sharing among the piles, the DMWs and the unstabilized soil are briefly described. Next, to clarify the contribution of the DMWs to bearing the structure load, the foundation behavior is simulated using a three-dimensional finite element model, and then the results of the numerical simulation are discussed."

Jan 1, 2015

By James Warner

Investigations of the sinkhole indicated that the loose, disturbed ground was completely encircled by dense competent core. This confinement substantially increased the effectiveness of the compaction grouting compared to what might have been expected at a "greenfield" site. However, the 8 ft diameter circle shown in the plan view was only the surface expression of the sinkhole proper and the deep, loosened ground actually extended to a larger diameter of about 20 ft. The planned spacing of the grout holes was based on the finite element simulations using a target void ratio of less than 0.3 throughout the compacted ground within a 5 ft radius of the grout injection point. Because of the strong confinement effect, the layout of grout holes included one central primary hole surrounded by six secondary holes at a triangular spacing of about 5 ft. Since the disturbed ground was considered a confined cylinder, it was anticipated that the primary hole would perform the majority of work and the secondary holes would act as check holes, with progressively lesser grout takes as the loose ground densified.

Feb 10, 2003

By Juan M. Pestana, Jeremy M. Gasser, Cuneyt Gokmen, Paul J. Sabatini, William Tanner, Daniel J. Woeste

An access pathway and working platform were designed and constructed for equipment access for a Deep Soil Mixing (DSM) pilot study over a coal combustion residual (CCR) surface impoundment (SI). The DSM pilot study was conducted to evaluate slurry mix designs and construction techniques for installing DSM columns up to 95 feet deep. Two-dimensional (2-D) limit equilibrium and 2-D finite element analyses were used to evaluate multiple failure mechanisms including: (i) bearing capacity, (ii) punching shear of mixed ground and underlying CCR, (iii) effect of fluidized DSM columns on working platform stability, and (iv) liquefaction. The analysis results were used to design ground improvement required to increase bearing capacity and stability of the CCR under the proposed equipment access route. A long-reach excavator was used to perform shallow bucket mixing and walk onto the CCR SI atop previously mixed cells following a minimum cure time and acceptance of quality control test results. Prior to mobilizing the DSM rig, a static load test was conducted to evaluate performance of the working platform. Both the access pathway and working platform demonstrated acceptable performance under the design loads during the DSM pilot study. This case study emphasizes the economic and safety benefits that can be realized by appropriately designing critical temporary work items such as access pathways and working platforms in difficult ground conditions. INTRODUCTION A Deep Soil Mixing (DSM) pilot study was conducted at a coal combustion residual (CCR) surface impoundment (SI) to evaluate slurry mix designs and construction techniques for closure design of the SI (Site). Sluicing of CCR at the facility ceased and closure will be initiated based on requirements in the final United States Environmental Protection Agency (USEPA) Rule for Disposal of Coal Combustion Residuals from Electric Utilities, 40 CFR 257, effective October 19, 2015. The proposed closure approach involves constructing a DSM containment structure (DSM Wall) to separate the SI into two areas: (i) a closure by removal area; and (ii) a consolidate and cap-in-place area. The proposed DSM Wall would retain the CCR within the consolidated closure footprint and provide a barrier between the two areas of the SI. The predominant CCR in the SI where the pilot study was conducted were fly ash and bottom ash. CCR materials in surface impoundments are generally soft and saturated as a result of being sluiced into place and can present stability and safety challenges when performing earthwork activities.

Jan 1, 2019

By Robert C. Simpson, Ghada S. Ellithy

"There are several methods for estimating the axial capacity of drilled shafts installed in coarse-grained soils. Most methods estimate the ultimate capacity for side friction and tip resistance. Design capacity is then calculated by applying a resistance factor to the ultimate capacity. In reality, however, ultimate resistance may not be mobilized except after a significant displacement that is not structurally tolerated in either compression or tension modes.A full- scale load test is the best way to obtain the load settlement curve for a drilled shaft, especially in soil formations where accurate estimation of soil frictional properties from a field investigation may be difficult. This paper presents the results of a static, axial, compressive bi-directional load test, using the Osterberg method (O-cell test). The test was designed so that the shaft above the O-cell would move up and the shaft below it would move down when loaded. At the start of the test the concrete around the O-cell is fractured generally on a plane near the bottom of the cell.The test was designed to validate the design capacity of drilled shafts embedded into the Vashon recessional outwash (Qvro), which is a glacially derived sediment consisting of thick deposits of cobbly sand and gravel relatively free of silt and clay found in the Seattle, WA area. The test shaft consisted of a 2.5- feet (0.75 m) diameter drilled shaft. The test shaft was installed to a depth of about 47 feet (14.3 m) into this formation. A maximum load of 437 kips (1.95 MN) was applied during the test, in each direction. The maximum load was attained at upward and downward displacements of less than 0.1 inch (2.5 mm), respectively.Although the load test did not yield ultimate values, the results are compared to the design assumptions using methods adopted in the FHWA and AASHTO guidelines, which verified the adequacy of the design assumptions. We conclude that more emphasis is needed in the prediction of the service loads and corresponding mobilized displacement that may lead to a more cost effective design. It is also clear that more testing to higher loads could lead to more efficient designs on specific projects and generally as data is added to the local knowledge base."

Jan 1, 2015

By Masaki Kitazume

"Many earthquakes take place every year in Japan, in which the 1995 Hyogoken-Nambu earthquake and the 2011 Tohoku earthquake induced both a humanitarian crisis and massive economic impacts. As liquefaction which occur in a loose and saturated sand layer, induces quite large damages of infrastructures, the importance of liquefaction mitigation has been emphasized to minimize earthquake disasters for many years. Many kinds of ground improvement techniques based on various improvement principles have been developed for earthquake disaster mitigation. Among them, the grid type deep mixing method has been often applied to liquefaction mitigation. In the method, the stiff grid walls are constructed by mixing the soil and binder in-situ, which are expected to restrict the shear deformation of the soil within the grid walls so that the pore water pressure generation can be remained small. The high applicability of the method was confirmed in several earthquakes, including the 1995 Hyogoken-Nambu earthquake and the 2011 Tohoku earthquake. In this paper, the development of the method, some applications of the deep mixing method to earthquake disaster mitigation are briefly introduced. INTRODUCTION In Japan, many earthquakes take place every year in Japan, in which the 1995 Hyogoken-Nambu earthquake and the 2011 Tohoku earthquake induced both a humanitarian crisis and massive economic impacts. As liquefaction induces quite large damages, the importance of liquefaction mitigation has been emphasized to minimize earthquake disasters for many years. Table 1 shows the amount of damage to port facilities (Noda, 1991). According to the table, the amount of damage when liquefaction takes place is about 20 to 50 times larger than that without liquefaction. This highlights the importance of liquefaction mitigation to minimize earthquake disasters. There are many kinds of soil stabilization techniques developed for liquefaction in Japan. Among them, the deep mixing method (DMM), an in-situ cement stabilization techniques, was developed in 1970s in Japan and has frequently been applied to improvements of clayey and sandy soils (Kitazume and Terashi, 2013). The grid type DMM has been often applied to prevent liquefaction, where the grid of stabilized column walls function to restrict generation of excess pore pressure in the soil within the walls by confining the soil particle movement. The improvement effect of the method was first evaluated in the Hyogoken-Nambu earthquake in 1995 and was also evaluated in the Tohoku earthquake in 2011. In this paper, some successful performance of the deep mixing method to earthquake disaster mitigation in the two earthquakes are briefly introduced."

Jan 1, 2015

By Ramanathan Ayothiraman, Anurag Singh

"An experimental program was undertaken to investigate the effects of randomly distributed basalt fibre on the index and engineering properties of Dhanori clay and to compare its performance with the properties of soil reinforced with polypropylene fibre. In the present investigation, 7 groups of soil samples were prepared at four different percentages of basalt fibre and polypropylene fibre content and tests were done for measuring their consistency limits, compaction characteristics, unconfined compression strength and consolidation properties. The test results indicate that the inclusion of basalt fibre in Dhanori clay resulted in significant improvement in properties. The improved properties are not comparable with polypropylene fibres, nevertheless, the improvement by basalt fibres is able to meet the typical design target values and the cost is very much less than synthetic fibres. More importantly, basalt fibres are environment friendly.INTRODUCTIONConstruction of buildings in low lands with engineered filling, flexible and rigid pavements for highways/airfields, and embankments for highways/railways are also part of major infrastructural development in addition to construction of tall buildings, bridges/fly overs, major dams and underground structures. The later projects require different improvement techniques than that is adopted in the former projects. Ground improvement techniques such as use of reinforcement inclusions within soil found as an effective and reliable technique. Especially such modification by fibre reinforcement, is primarily possible in engineered filling, pavements subgrade and embankments, where surface mixing is easier; and may not be feasible when stabilization/modification is required for deeper depths. In comparison with conventional reinforcement using geosynthetics (strips, geotextile, geogrid, etc.), there are some advantages in using randomly distributed fibre as reinforcement. In past few decades, the discrete fibres are simply added and mixed randomly with soil, in much the same way as cement, lime, or other additives.There are several studies (Ziegler et al. 1998; Puppala et al. 2000; Bei-xing et al. 2004; Cai et al. 2006; Tang et al. 2007, 2012, 2016; Abdi et al. 2008; Viswanadham et al. 2009; Le et al. 2015) that investigated the behaviour of polypropylene fibre-reinforced soil and reported that an increase in fibre content caused an increase in strength and shrinkage potential but brought on the reduction of swelling potential. The length of fibres had an insignificant effect on soil characteristics, whereas fibre contents proved more influential and effective. A study on rubber fibre conducted by Hambirao and Rakaraddi (2014) mentions that tensile cracking of clays can be improved with the inclusion of short rubber fibres, optimum fibre content was about 15 % of weight of soil. Several experimental studies (Babu et al. 2008; Chaple and Dhatrak 2013; Vibhakar and Nahta 2014; Soundara and Senthilkumar 2015; Goyal et al. 2015; Jayasree et al. 2014, 2015) were conducted on coir fibre-reinforced soil and concluded that it helped in reducing the swell potential and 1% fibre by weight of the soil almost doubled the CBR value. Martins et al. (2015) found that 4% of sisal fibre by weight of the soil reduced the visibility of cracks. Pillai and Ayothiraman (2012), Ayothiraman et al. (2014) and Sahu et al. (2016) have demonstrated that human hair fibres can be used to improve the properties of both fine grained and coarse grained soils."

Jan 1, 1900