Search Documents

By Ernest Naesgaard

Post-grouted micro-piles were used for the seismic upgrading of the Vancouver International Airport Domestic Terminal Building (DTB). The micro-piles provided vertical resistance to both uplift and compression loads to supplement the existing timber pile foundations ability to resist the earthquake induced forces, and to provide foundation support at locations where the installation of traditional driven piles was difficult. This paper describes the site conditions, design rationale, installation method and quality control testing procedures. Site and Subsurface Conditions Vancouver International Airport is located within the central portion of Sea Island, Richmond, British Columbia (Fig. 1). Sea Island is bordered by branches of the Fraser River on the northeast and south sides and the Strait of Georgia along the west side. The natural grade of the island is part of a large delta that has been built up over several thousand years. The general pattern of sediment deposition has followed the direction of the Fraser River flow from east to west, and has built up soft sediments of about 200 m thickness at Sea Island (Luternauer, et al. 1993, Mathews and Shepard 1962). The original grade in 1962 prior to the existing Airport Terminal Building development was at about geodetic elevation 1.1 m with a grass and topsoil cover.

Jan 1, 2004

By Mark Zablocki, Dakarai McCoy

Ground vibrations are an unavoidable effect of driving piles and may pose a risk to nearby infrastructure and the comfort of adjacent occupants. Driven-pile-induced ground vibrations are known to vary widely based on ground conditions, pile material, and installation means and methods. A monitoring sensor to record ground vibrations during pile driving is necessary for understanding potential impacts to sensitive infrastructure and should be considered when implementing a monitoring program anticipating ground vibrations. The implementation of a vibration monitoring program historically relies on experiential-based decision-making, which may result in the costly vibration monitoring of low-risk infrastructure. Prior understanding of anticipated ground vibrations is necessary to create an appropriate monitoring program. A framework is proposed for organizing data from past monitoring programs and quantifying the anticipated risk of driven-pile-induced vibrations. An example of risk quantification from data imported to ]a cloud database is presented by comparing driven steel H-pile and prestressed precast concrete vibration monitoring measured and collected by Haley & Aldrich between 2010 and 2020. The methods presented within the example can be applied to quantify a first order approximation of risk for ground vibrations at proposed driven pile sites based on the measured performance of previous sites with similar ground characteristics and pile installation methods. The presented novel data managements tools allow for a quick aggregation of vibration data with similar site conditions.

Sep 8, 2021

By John P. Davis

The use of conventional, circulatory air rotary and fluid rotary, cased and uncased drilling methods in the vicinity of sensitive infrastructure can have deleterious effects on the ground conditions surrounding and supporting structures and the structure itself. Furthermore, the use of these conventional methods offers the engineer or contractor little information about the condition of the subsurface during geotechnical applications. Conversely, sonic drilling measurements and samples can be used to evaluate actual conditions during the progress of exploration and construction across a given site. This paper will discuss the history and properties of sonic drilling and explore case histories of geotechnical applications for the advancement of boreholes within vulnerable structures and on sensitive sites for several recent infrastructure projects ? a tunnel and railroad project, a dam grout curtain project, a bridge micropile exploration project and a tunnel instrumentation project. Project summaries will discuss the advantages realized when the application of sonic drilling techniques demonstrated superior accuracy, quality control, efficiency, productivity, penetrability, waste minimization and adaptability when drilling adjacent to or within existing infrastructure. Finally, the discussion will address the current testing and application of sonic drilling to the installation of micropiles, earth retention anchors, grout injection and instrumentation installation where the quality control benefits provided by the inherent soil cores, measurement while drilling systems, accuracy and non-destructive production drilling features will be advantageous.

Jan 1, 2006

By P. Bermingham

A new approach to load testing of high capacity piles is presented. The method is mobile, inexpensive, repeatable and non-destructive allowing for multiple pile testing at a single site. A reaction mass is placed over a pressure chamber situated atop the pile to be tested. The test method is significant in that it can produce linearly increasing forces of high magnitude (over 5.0 MN) with durations of up to 80 milliseconds. This represents pulse durations an order of magnitude longer than achieved using a drop hammer. The accelerations the pile undergoes are less than one g, (conventional dynamic methods = 50 to 100 g). These effects combine to produce pile behaviour no longer dominated by the action of stress wave, instead the pile is under high levels of stress through its length during the force input. This is representative of the situation when static loads are applied, thus the method may be considered quasi-static. Further advances introduced with this method are that pile deflection and transmitted force are measured directly by means of a laser beam and load cell. This allows accurate correlation of event load displacement histories without the error associated with zero shift (acceleration integration) or non-homogeneous materials (strain measurement). The load displacement histories emulate those obtained for static load testing.

Jan 1, 1989

By Jiwei Duan

The energy transferred from a hammer to the pile top is considered as the effective energy in this paper. The effective energy is related to the pile dimensions, soil and pile-soil interface properties. This relation may be expressed as an equation based on the dimensionless theory. The relationship between pile capacity and effective energy was studied by performing a series of wave equation analyses using a commercial software called GRLWEAP (Wave Equation Analysis Program) by GRL Engineers, Inc. The results show that the pile capacity increases with the blow count when the effective energy is constant, however, it has a little change as the blow count is over 100 blows per foot. The pile capacity decreases as the ratio of pile penetration depth to pile diameter increases if the effective energy is constant. The pile capacity will increase as the pile diameter and wall thickness increases if the effective energy is constant. The pile stickout (pile length above the ground surface) does not have a significant effect on the effective energy and may be neglected. Curves for pile capacity versus effective energy are presented to be used for preliminary hammer selection according to effective energy and hammer efficiency. Finally, a case from PDA testing was studied. Measurements of the effective energy and pile capacity by CAPWAP were presented and compared with the results by GRLWEAP.

Jan 1, 2006

By José Carlos A. Cintra

This paper addresses a new experimental procedure to measure the shaft friction and the base resistance of bored piles during static load tests. It is proposed that a set of polystyrene foam discs, placed between the shaft and the base of the pile, be used instead of the usual instrumentation. Throughout the initial stages of the loading test, the foam discs will allow only the mobilization of the shaft friction. The load x settlement curve clearly shows that the shaft friction vanishes at low settlement values. As the load test proceeds, the base resistance is also mobilized. This procedure was used in two belled piles bored at the Experimental Foundation Field of the University of São Paulo, at São Carlos, Brazil. Both piles were 8 m long and had a shaft diameter of 0.6 m. The enlarged base had a diameter of 1.5 m and a height of 0.9 m. Twenty foam discs with a thickness of 20 mm each were placed between the enlarged base and the shaft of the pile. The load tests indicated ultimate shaft frictions of 28 and 30 kPa for measured settlements of 8.98 and 7.39 mm. Base resistance values at failure were 617 and 499 kPa, for a chosen settlement of 10% of the pile base diameter. The proposed approach seems to be straightforward, efficient and inexpensive.

Jan 1, 2002

By Wen-Chieh Cheng

Two bored piles with base grouting are loaded axially and the results are used to compare with numerical analyses. One compressive pile with a diameter of 2 meters is drilled through clay deposit and into bedrock to a depth of 13.7 meters. One tensile pile with a diameter of 1.5 meters is drilled through the same clay deposit and into bedrock to a depth of 17 meters. Both piles are installed with monitoring system such as rebar strain meters, concrete strain gauges and extensometers. The monitored data during pile load test are used to obtain average frictional stress (t) a displacement (z) curve, pile tip bearing (q) as well as pile head load (p) and a displacement (s) curve. FLAC3D is used to simulate the pile loading and base grouting. The soil and bedrock are modeled with Mohr-Coulomb. The parameters of the constitutive law are established from soil biaxial tests and rock bore hole deformation tests. The pile is assumed as an elastic body. The interface element is used to simulate the pile/soil interface and pile/rock interface. The numerical results are compared with the pile load test in terms of t-z curve, q-z curve and p-s curve. Finally, the pile base grouting is simulated and the uplift is analyzed. The result from this study is promising and the numerical modeling is successful.

Jan 1, 2006

By Saba Mohan

This study presents results based on the Pile Installation Demonstration Project (PIDP) that was conducted as a part of the East Span San Francisco-Oakland Bay Bridge Seismic Safety Project. For the three full-scale pile installations, two different high-energy hydraulic hammers were selected for the installation. However, these hammers may not have sufficient energy to drive these large diameter piles at their ultimate capacity following long-term set-up. Nevertheless, these hammers were selected because, soil plug behavior, the generation of excess pore pressures and remolding of soil during driving were expected to reduce the shaft and end bearing resistance, and therefore reduce the energy required to drive these piles to design penetration. Data collected during continuous installation driving and after a series of re-strikes at different set-up times ranging from 1 to 33 days were used as input data for CAPWAP. These results were used to estimate the soil resistance along the pile length and at the toe of the pile, and the soil pile set-up behavior. Validity of the procedures used to predict the soil resistance to driving and predicted blow counts were verified with the field observed blow counts and the energy that was delivered to the pile. Based on combined CAPWAP analyses, the soil pile set-up with time was estimated and compared with results of other methods currently available in the literature for predicting the soil pile set-up rate.

Jan 1, 2002

By Raymond E. Sandiford

"The redevelopment of the World Trade Center (WTC) provided an opportunity for the Port Authority of NY and NJ to complete a long sought underground connection between all of Lower Manhattan’s transit lines, the World Trade Center and the World Financial Center (WFC) (Figure 1). Creating this connection was a challenge because the WFC lies west of the heavily trafficked Route 9A, also known as West Street. The previous connection was a bridge that required pedestrians to make significant level and directional changes to navigate the crossing. The positioning and elevation of the Route 9A pedestrian tunnel was established to provide pedestrians with a clear, single level, climate controlled corridor from the new WTC Transit HUB to escalators leading into the WFC Winter Garden.As the most direct link to the WFC, tens of thousands of people a day will use the pedestrian corridor. To accommodate this large number of pedestrians and provide an obstruction free passage, the tunnel has a clear width of 50 ft (15.2 m). Although only 250 ft (76.2 m) long, that short length presented many technical challenges.Here I describe how the challenges were overcome during the construction. However, some of the truly problematic issues arose from coordinating the phasing of this project with adjacent construction activities at the WTC, the reconstruction of Route 9A, and the WFC’s redevelopment program. The limited access to the excavation areas and confined site logistics were further complicated by having to maintain six lanes of traffic on Route 9A at all times. The efforts were so intertwined that, well into the underpass construction, the Port Authority Construction Department decided to merge a portion of that work into the WFC redevelopment."

Jan 1, 2012

By Phillip E. Glogowski, N. Catherine Bazan-Arias

Steel foundations can be designed to cross-sectional configurations ranging from triangular and square to other multi-side shapes. Adding lateral extensions (hereby called wings) along the length of the steel stem can increase the foundation’s uplift, torsional and lateral load capacities. DiGioia Gray staff developed a methodology for the optimal design for multi-facetted, winged deep steel foundations. A finite element (FE) model is used to represent the steel components and the nonlinear subsurface behavior. The geometry of the foundation can be complex; thus, an optimal design needs to be fine-tuned to the specific site conditions. We created a pre-processor tool to generate the FE model including varying values for the number and size of wings, depths of embedment, reveal/stickup heights, top plate geometries, and subsurface profiles. The analytical model has been partially validated through full-scale testing and the methodology has been applied to two installed projects to date.

Sep 8, 2021

By Jim Bruce

No answer required. From the drilling equipment suppliers, but the specifications must be tailored to be project-specific. Yes, the sonic technique is very interesting as we said, and it is not so much as an issue of the magnitude of power, it's about the efficient use of the power. The efficiency of the machine is not necessarily related to size so it is best to talk to the two contractors that supply the service about that. I think it can be scaled down but it is quite a big head, so therefore there are practical limitations on the size of the door it can walk through and also the size of the casings and rods that it can use. You might defeat the economic advantages if you were to use too short casing lengths. Boart Longyear have a low head room machine that can work within an 8 foot verical clearance.

Feb 10, 2003

By Stephan Jefferis

It is my understanding that the Scandinavians have done some fundamental work on durability. I have seen a study published whereby the author, Helen Anderson, comments on the durability of polyurethane grouts and there was -if I am not mistaken- a reference made to another Scandinavian testing institute comparing durability of the polyurethane to cement grout under the same type of circumstances. Circumstances are important so we should actually ask the gentleman to shed some light on this particular method because apparently Scandinavia is the place where durability has been taken very seriously and has been well researched.

Feb 10, 2003

By Allen B. Stanton, Parthiv Brahmbhatt, Michael Grimm, Stanley L. Worst

Constructing a circular shaft consisting of secant piles has its own complications which make it more difficult than typical drilled shaft construction. Add to that performing under low overhead powerlines and sitting inside of a 40-foot deep, 50-foot diameter shaft and it becomes more about logistics than the actual drilling. The complexities associated with the Romeo Arm Interceptor Segment 5 Lining project are the focus of this paper, delving into the details that made it work successfully.

Oct 1, 2022

[ENGLISH active earth pressure adapter additive adhesion admixture, addition adsorbed water aggregate air air entrainment air hose allowable bearing value allowable pile bearing load]

Jan 1, 1994

By Masaki Kitazume

Five papers were presented orally to the topics of Jet Grouting and Deep Mixing. The session was started with a brief introduction by the moderators. Following the oral presentation, floor discussions were directed by the moderators. A brief introduction of each of the oral presentations is provided before each discussion.

Feb 10, 2003

By Paul R. Lear

Sustainability continues to be an important aspect of remediation and infrastructure projects. Deep soil mixing (DSM), a common construction and remedial technology, can easily incorporate the following sustainability best management practices (BMPs), including Minimizing Total Energy Use and Maximizing Use of Renewable Energy; Minimizing Air Pollutants and Greenhouse Gas (GHG) Emissions and Maximizing Use of Machinery Equipped with Advanced Emission; Minimizing Water Use and Impacts to Water Resources; Beneficial Reuse of Materials/Reduction of Materials and Waste Reduction; Use of Local Labor and Supplies. This paper focuses on the sustainability of DSM treatment and provide carbon footprint calculations at least one completed DSM project which used these sustainability BMPs to demonstrate the environmental impact of the sustainability.

Sep 8, 2021

By J. J. Beresford

The primary function of a support slurry is to provide stability during excavation. Today foundation structures can be designed around the additional friction afforded by the absence of the filter cake attributable to the use of polymeric fluids as support slurries. These fluids use pseudoplastic fluid viscosity to advantage over the fragile thixotropic gel structures of bentonite. Many of today's polymeric fluids are environmentally acceptable for disposal directly to municipal sewers.

Jan 1, 1989

By Patrick J. Hannigan

A comparison of 40 statically and dynamically load tested piles was performed to evaluate the variation between testing methods. This evaluation indicated an agreement of 10% to 15% could be obtained when the available static resistance is fully mobilized by both methods and when time dependent capacity changes are minimized. Dynamic pile testing recommendations for minimum induced impact force, ram weight to pile weight ratio, and considerations for time dependent capacity changes are presented.

Jan 1, 1987

By Gordon King

The City of Atlanta Water Department required the construction of a two sludge tanks and a wet well at the existing Chattahoochee Water Treatment Plant. Western Summit won a design build contract to build the project and proceeded to evaluate the wet well size options, and construction procedures. The final design required the construction of a 1 million gallon tank. The proximity of the underground tank to adjacent roads and existing plant structures ruled out laying back the excavation. As a result a tied back sheet pile retaining wall was initially proposed.

Jan 1, 2003

By B. C. Slocombe

A large derelict inner city site was regenerated for use as a distribution warehouse. Difficult topography and soils conditions required the adoption of a combination of specialist geotechnical processes. Particular attention was paid to the preparation of the site, programming and capabilities of each technique as additional soils information became available.

Jan 1, 1989