Search Documents

By Peter Jackson

The dewatering of the large construction pits required for major infrastructure projects often has a significant impact on the environment. This is particularly so in urban areas and where groundwater resources are of interest. These environmental impacts are inter alia, groundwater lowering and the consequent effects such as settlement and deterioration of timber foundations, together with the impact of the dewatering on the groundwater quality. In order to minimise the environmental impact of the dewatering, the quantity of water to be abstracted and the amount of groundwater lowering in the surrounding area must be minimised. This paper describes the measures that have been taken on the Copenhagen metro project to achieve the objective of minimal environmental impact whilst still carrying out a major dewatering scheme.

Jan 1, 2000

By Steve Thoman

After the 1989 Loma Prieta Earthquake, the California Department of Transportation (Caltrans) initiated an overview of the Caltrans Bridge Design Specifications (BDS) and bridge seismic design practice in California. This overview is continuing under the direction of the Applied Technologies Council (ATC-32), to review and revise as necessary existing standards, performance criteria, specifications, and practices for design and construction of new bridge structures within California. The ATC-32 project began in August 1991 and is expected to be completed in 1995. Since 1990, Caltrans project-specific seismic criteria have been developed and implemented on the I-280 and I-480 projects in San Francisco. Caltrans and an independent seismic safety review panel continue to develop and implement these criteria on other projects. In 1991 and 1992, project-specific seismic criteria were used on the I-880 reconstruction project in Oakland. The seismic safety review panel considered the I-880 seismic design criteria a state-of-the-art methodology to ensure seismic safety against collapse of bridge structures subjected to a maximum credible seismic event. This paper highlights the 1992 "I-880 Reconstruction Project Seismic Design Criteria Review" report prepared by the Seismic Safety Review Panel and Caltrans Division of Structures and will compare pre-1989 BDS and AASHTO methodologies to the I-880 criteria.

Jan 1, 1996

By John S. Pack

The last 25 years have seen rapid expansion in the use of helical screw pile foundations and tiebacks for new and retrofit construction of buildings and earth retention structures. An estimated $100 million was spent in 2002 on helical foundations and tiebacks in the United States alone. While design information is available in the literature, information regarding quality control, inspection and performance monitoring is lacking. Recognition of at least one manufacturer's helical foundation material by the Uniform Building Code, Standard Building Code, and BOCA (all three codes now combined into the ICC International Building Code) has given added urgency to the dissemination of reliable and practical quality control, inspection and performance monitoring procedures. This paper describes a set of such procedures that have been followed for 17 years by engineers experienced in the industry who have directly installed or been involved in the installation of over 140,000 helical foundations and tiebacks in divers soil conditions for various types of structures, including earth retention structures. Topics covered include design responsibility, building code listings and requirements, manufacturer ISO certification, manufacturing process, material and installation specifications, installation contractor certification, field placement, installation procedures, field inspection, building code inspection and performance monitoring. The paper concludes with a step by step example of practical quality control, inspection and performance monitoring procedures on a typical helical foundation project.

Jan 1, 2003

By Jan Pru?ka

This paper describes the sheet pile design for the Line C extension from Ládví station to the North of Prague. The first part of the paper describes the geological conditions and structural configuration of the project. Typical cross sections, the description of the construction stages, and monitoring are discussed. The second part of the paper focuses on the sheeting design method. It describes the method of dependent pressures, that is, how the pressures acting upon a structure depend on the deformation. The design process and verification methodology are described in detail with comparison of the results with in-situ monitoring.

Jan 1, 2011

By Gray Mullins

A post grouted drilled shaft foundation system was successfully used in place of the specified driven pile foundation system as a Value Engineering Cost Proposal (VECP) for the new PGA Boulevard Grade Separation Project. Pressure grouting the cohesionless sandy soils at the drilled shaft base significantly increased the end bearing capacity and stiffness allowing drilled shafts to be the more cost effective foundation system. The post grouted drilled shaft option also provided other benefits including reducing owners risk normally associated with pile driving vibrations and offered a high level of quality assurance for the drilled shafts. This paper discusses the implementation of post grouted drilled shafts from design to completion of construction. A design procedure for post grouted drilled shafts developed by the University of South Florida was used for initial VECP evaluation. Prior to construction, two instrumented test shafts were installed and load tested, one of which was post grouted. Therein, the design procedure was calibrated, tip elevations for production shafts were refined, drilled shaft construction and grouting procedures were demonstrated, and a grouting criteria was developed for the project.

Jan 1, 2003

By Aly M. Mohammad

The Delaware River Tramway will link civic and retail developments in Philadelphia, Pennsylvania and Camden, New Jersey. Twin 300-foot towers will anchor the cables at either side of the river. Four high capacity drilled shafts designed by the Geotechnical Department of DMJM+HARRIS support each of the towers. At the Philadelphia tower, each 6-foot diameter shaft extends 130 feet deep and terminates with a 30-foot rock socket. The shafts are situated within the footprint of an existing relieving platform, which complicates the typical construction sequence. Also, the subsurface conditions at the site provide a unique challenge in both the design and construction of the drilled shafts. During the construction of the four-drilled shafts for the Philadelphia tower, a 6000-ton Osterberg load test was performed on the first shaft to verify design assumption and confirm the shaft capacity. The results of the test were utilized to establish load transfer characteristics and develop foundation design parameters suitable for the site conditions. By doing so the Design Engineer was able to reduce the length of the rock sockets on the remaining production shafts by approximately 5 feet per shaft. As a result, the test provided a significant cost saving to the Owner by eliminating 15 feet of rock drilling from the construction costs. This paper presents a description of the unique design and construction methods adopted for the foundations, also on the Osterberg load test including equipment used, number and locations of strain gages, and interpretation of results. The results and findings presented in this paper could benefit both the design and construction industries because it provides a comparison between geotechnical design assumption and actual field measurements; which has always been a challenge particularly for rock formation.

Jan 1, 2002

By Osama Safaqah

The new Cooper River Bridge will replace two existing bridges along U.S. Highway 17. The cable-stayed bridge will be one of the largest in the U.S and will connect the City of Charleston and the town of Mount Pleasant, South Carolina. The 1,546-foot long main span over Cooper River is supported by two diamond-shaped towers and will allow for 1000-foot wide navigation channel. The Charleston high-level approach is approximately 4351-foot long and will provide 250-foot wide navigation channel over Town Creek, while the Mount Pleasant high-level approach is 2090-foot long. Due to the high seismicity in the region, potential vessel impact, and hurricanes, large lateral loads are expected. Among various types of foundations, 10-foot diameter drilled shafts were selected for their high capacity against lateral loading. The shafts are founded on a stiff to very stiff lightly cemented calcareous sandy clay or sandy silt layer, called Cooper Marl, which underlies coastal sediments of interbedded clays and sands. The main towers will be supported on a group of 11 shafts and protected from ship collision by a rock island. The High Level Approach piers will be supported on a pair of 2 shafts. The shaft tip elevation is up to 230 feet below water line. An elaborate geotechnical investigation has been conducted on the site including a load test program on full-scale shafts under axial and lateral loads. The results of the tests were used to calibrate the lateral and axial soil resistance. The objective of this paper is to present the different aspects of the bridge foundation design.

Jan 1, 2005

By B. Broms

The "Bawang Pile" (in english "onion" pile) described in the article consists of a cased concrete shaft and an expanded base. The steel casing is first driven by an internal drop hammer and then the base is formed in-situ by the raming the concrete at the bottom of the slitted casing. This new type of pile can be used for underpining (small head room) of buildings and as foundation for transmission towers or lamp posts. Full-scale load tests in compression and in tension on the Bawang pile and on steel pipe piles demonstrate the dramatic increase of the ultimate capacity due to the expanded base. Guidelines for the design of such piles are proposed.

Jan 1, 2010

By Jorj O. Osterberg

The Osterberg (O-Cell) Method makes it possible to separate the side shear resistance (skin friction) from end bearing. The O-Cell is placed on or near the bottom of a drilled shaft and after the concrete is poured and cured, an equal upward and downward pressure is applied. From the test, the load-upward deflection curve in side shear and the load-downward deflection curve in end bearing are drawn. Typical curves are shown where the ultimate load in side-shear is reached and where the ultimate load in end bearing is reached. Several examples of tests in which the test load reached ultimate loads far in excess of what was expected are shown. The side shear in rock sockets is shown to be much larger than generally estimated. Examples are given of where side shear is smaller than expected and the reasons discussed. Disturbance of the sides of drilled holes due to poor construction techniques and ways to avoid these conditions are considered. Examples of bottom hole disturbance are given and ways to prevent the disturbance are discussed. A graph showing the actual measured capacity of drilled shafts compared to the estimated capacity as a function of the hardness and strength of the soil or rock is presented.

Jan 1, 1999

By Anuj K. Singh, Shuvranshu Rout, Manos De

"Foundation for tracks of coke transfer car and dust extraction pipe was designed as series of isolated foundations spaced at 11.0m along length of coke oven battery resting on soil at depth of 2.5m. In one region the foundations are close to adjacent 12m deep underground junction house. Five foundations in this zone were constructed on backfilled soil without proper compaction instead of engineering soil fill or concrete fill. The foundations settled under loads and the supported frame structure tilted after equipment erection and during trials endangering the safety of the structure and equipment operation. The distorted structure had to be rectified in-situ by arresting settlement. In order to stabilize the foundation and supported structure the supporting soil had to be strengthened in situ without any dismantling, reconstruction and adverse effect to equipment operation. This paper presents the case study on the evaluation of defects for the foundation failure and analysis of the problem, proposed rectification of the situation by appropriate soil stabilization scheme, monitoring of the stabilization operations and verification of effectiveness of the rectification work by measurement of settlements. The implemented solution has ensured safety of the structure and equipment without any adverse impact on normal operation.INTRODUCTION AND BACKGROUNDNew Coke Oven Battery was being installed for an integrated Steel Plant. The hot coke from oven is pushed out after completion of coking process through a coke transfer car onto a hot coke receiving car. The coke transfer car runs on rail track parallel to the line of ovens forming the coke oven battery. One rail is supported on the structure of the operating platform of the battery and the second rail rests on independent structure of track beams. A large diameter pipe for extraction of the dust emitted during coke pushing operation is also supported on the same structure that supports the track beams. The entire structure rests on columns spaced at approximately 11.0m along the length of the battery. The columns transfer load to ground through individual foundations resting on competent subsoil strata.Two sets of foundations for the rail track beam support and dust extraction pipe support are adjacent to deep underground junction house of coke carrying conveyor. The depth of the pit for the junction house is 12m. The layout and arrangement of the foundations in this region around the junction house (JH-1) is shown in the “Figs. 1a, 1b”."

Jan 1, 2017

By Magnus Ruin

The dry deep mixing method for stabilization of soft soil has been used in the Scandinavian countries for 25 years. The typical application has been stabilization of soft inorganic clay. Today the method is used more frequently in organic soil with good results. The Limix System, introduced in the USA by Hercules Grundläggning AB and TREVIICOS Corporation, is a cost-effective dry deep mixing method used to stabilize most types of soft soil. This paper presents the general principles of stabilizing organic soil with the dry mix method and two case histories of soil stabilization projects in organic soil. Between October 2000 and June 2001 the Limix System was used in England to stabilize soft organic alluvium at the Channel Tunnel Rail Link, Contract 440. During year 2000 the Limix System was used in soft organic soil in Holland near the Groene Hart Tunnel entrance to support trench excavations for slurry walls and concrete barrettes.

Jan 1, 2001

By Roy M. Schnabel

The Fashion Island Boulevard Bridge over the Marina Lagoon in San Mateo, California is an eight span precast, prestressed concrete girder bridge. It is approximately 495 feet in length and 61 feet in width. It is supported on 36" diameter octagonal, hollow precast-prestressed concrete pile columns. The bridge was constructed in 1968 and suffered considerable damage during the Loma Prieta Earthquake in 1989. A damage survey report prepared by the State's Office of Emergency Services (OES) recorded that sixteen of the twenty-one pile-columns sustained heavy to moderate damage from the Loma Prieta Earthquake. The damage consisted of cracking and spalling at the tops of the pile-columns. Spalls at the most heavily damaged columns exposed the prestressing strands and confinement reinforcing which also showed signs of corrosion.

Jan 1, 1993

By Mohammad Eslami

The Tabriz-Urmiyeh Highway shortens the distance of north-western cities of Iran by about 130 km, resulting in improved access and efficient transit between Iran and Europe through Turkey. The highway crosses the Urmiyeh Lake, an inland lake surrounded by mountains. Due to the circulation of salt-water in the lake and the necessity to continue shipping between adjacent ports, a waterway should be kept open. Consequently, a bridge was built to provide access of marine traffic. A causeway bridge had a length of 1,260 m, comprising of 19 spans. In construction of the bridge, more than 400 piles having a total length of 32 km have been driven. For design of piles different methods have been used such as static analysis, dynamic testing, and correlations to in situ tests, such as cone penetration test (CPT). This paper presents construction of bridge substructure, full-scale piling tests, and methods of analysis used in the evaluation of the deep foundation capacity. The presentation includes an assessment of four current direct CPT and one CPTu methods to calculate the bearing capacity of the piles. It was found that the CPTu and dynamic testing are two suitable tools for rapid and optimum pile design and verification.

Jan 1, 2010

By Dennis Nottingham

Spin-fin pipe piles can develop large loads in tension, thus have evolved as a foundation product of great potential. Currently, over 500 spin-fin piles have been used successfully in dolphins, docks, buildings and bulkheads. Spin-fin piles are pipe piles with plates welded near the tip at a batter-in-screw fashion. Thus, as the pile is driven, the pile screws into position. Tests show this pile type to have highly unusual stress/strain relationships, wherein plunging failure is usually never reached either at normal or large deformations. Tension capacity can approach pile capacity in bearing; thus, large reserves are usually available for tension. Tests have been performed on 8-5/8-inch to 24-inch-diameter piles in silt, sand, and gravelly soil, to provide a broad spectrum of data.

Jan 1, 1990

By Willie M. NeSmith

Cast-in-place piling are a staple of the deep foundation industry, and are used (in various forms) worldwide. In assessing the application of cast-in-place piles, it is of value to reflect on the development of the various systems, in order to understand how the current processes and equipment came to be. This paper traces the evolution of the cast-in-place industry. Emphasis is on developments in the United States; however, since there has been a substantial fusion of US and European processes, notable European developments are also discussed.

Jan 1, 2006

By Leong, William. Chong, Kam Weng

Deep Vibro Techniques namely Vibro Compaction (VC) and Vibro Replacement (VR) are widely used in ground improvement to densify sands and strengthen cohesive soils. This paper describes the application of these techniques for the construction of 20 Ha Iron Ore Stockpile Yard with the maximum stockpile height of 14 m in Quang Ngai, Vietnam. The challenges of this project are to limit the stockpile allowable settlement and the surrounding pile’s lateral movement. The soil condition can be summarized as 12m – 18m thick of loose to medium dense SAND with qc around 5-18MPa and followed by 2.0 – 6.0 m thick soft clay with qc around 0.4 – 0.8MPa. Localized very dense sand layer was found. VR using stone columns were installed in soft clay layer while VC was adopted to densify sand layer. Additional shallow stone columns were built in sand strata to minimize pile top lateral movement. The post construction performance was verified by a large 6 m by 12 m plate load test (PLT). The predicted PLT deformation using Priebe’s improved properties for the VR will be presented and compared with the measured plate load test results.

Nov 1, 2022

By Robert W. Schaut

The use of micropiles is increasing for new construction and to retrofit distressed foundations in expansive soils. Typical micropiles in expansive soils have a lower section where the micropile grout is embedded in direct contact with the soil, and an upper section that is cased with rigid PVC pipe or other material to reduce the friction between the micropile and the surrounding expansive soil. In the upper cased section, the micropile grout is in direct contact with the inside of the casing. During construction, grout can flow upward into the annular space between the soil and the outside of the casing as the grout is tremied into the micropile. Thus, various interfaces may exist in a typical micropile, including soil-to-grout, grout-to-PVC, and soil-to-PVC. As the surrounding soil heaves, shear stresses are mobilized along the interfaces. The frictional characteristics of the interfaces are design variables that must be evaluated. For this study, an experimental program was conducted to evaluate the shear strength of the three interfaces listed above. Conventional direct shear testing was performed at a commercial testing laboratory. In addition, specialized testing was performed at Colorado State University (CSU). For the CSU testing, an interface testing protocol was designed using a modified triaxial cell to allow evaluation of the interface characteristics between rigid PVC and cylindrical specimens of grout or clay soil. It is shown that the shear strength of the soil-to-PVC and grout-to-PVC interfaces are similar, both of which are significantly lower than the shear strength of the soil-to-grout interface. This indicates that the use of a PVC casing in the upper portion of a micropile has a positive effect in reducing friction and the shear stresses resulting from expansive soil.

Jan 1, 2011

By Peter J. Nicholson

Since the reintroduction of soil mixing to the United States over 10 years ago, the work installed by soil mixing technology has grown dramatically. From an annual turnover of less than ten million dollars per year the volume of soil mixing put in place has grown to an estimated $40 million per year in the year 2000. The majority of work done to date has involved walls, either for excavation support, permanent retaining structures or hydraulic cut-off walls. The other major use for soil mixing has been for mass stabilization of soils whether for isolation of contaminants or for retaining structures. This paper will discuss the uses of and costs of typical soil mix structures. BACKGROUND Soil mixing is defined as the in-situ combining of reagents, typically cement, with native soils, the purpose being to modify or improve the ground. This history of soil mixing covers only the use of cement slurry, aggregated with soil in-situ by mechanical mixing methods only. Soil mixing by use of high-pressure hydraulic means, also known as Jet Grouting, will not be discussed. In addition this will not cover ex-situ (above ground) mixing, or mixing dry reagents with soil. Only mixing applications for building, civil and heavy construction applications will be discussed, with only passing reference made to uses of soil mixing for environmental remediation work.

Jan 1, 2001

By Ron Bromenschenkel

The State of California, Department of Transportation is currently retrofitting a major interchange near the San Francisco area. The project is located in a highly traveled area of Oakland with light rail commuter service near many footings. Over 600 micropiles are being used in conjunction with CIDH piles for footing stabilization. A specially designed Soil Nail pile will support footings for a new light rail utility structure. Pile testing features in this contract serve as points of interest for future foundation designs. The presentation focuses on substructure issues of this incterchange retrofit. Both design and construction considerations will be covered. Design Considerations: ? Project Description ? Structure inadequacies ? Design criteria ? Design contraints ? Retrofit strategy ? Consultant analysis ? Pile Designs and Test Sites ? Contract Specifications ? Construction Plan and Cost

Jan 1, 1998

By Jim Steding

L.G. Barcus and Sons, Inc. recently completed a three-phase project for the expansion of Presbyterian Hospital in Albuquerque, New Mexico for McCarthy Construction Co., the Construction Manager for the project. It was a challenge that allowed Barcus to demonstrate many of it's strengths. Safety of people and property, restricted access, low headroom conditions, extensive planning to maintain hospital operations and a tight schedule were all key elements affecting the successful installation of the Augered Cast-In-Place Piles. Phase I began with installing and performing a 450-ton pile load test on an 18-inch diameter Augerpile 65 ft long. The load test was installed and performed directly in front of the Emergency Room entrance. Space was limited and the E.R. had to remain open with uninterrupted ambulance access. The results of the load test were outstanding. In fact the test pile performed so well that some of the job piles were shortened from 75 ft long to 65 ft long. [ ]

Jan 1, 2003