Search Documents

By Akira Usui

Platinum is one of the most rare elements in the earth?s crust, but it is significantly enriched in some hydrogenetic ferromanganese crusts in the ocean. The element is essential to the electric industry and is believed to be of importance as a raw material a future fuel-cell industry. The earlier reliable chemical analysis of platinum-group elements (PGE) of ferromanganese crusts have indicated a variety of concentrations of Pt in the range of 100 ppb to a maximum of about 1 ppm, but little is known about the elemental abundance in ferromanganese crusts on fine-scale, or the geochemical behavior and form of the element. The chemical and mineralogical forms of platinum and its group are important in planning the methods of mineral exploration and extraction of the elements from of ferromanganese crusts. We attempted to characterize the distribution pattern within a cobalt-rich crust on the fine to microscopic scales by using reflecting microscope, scanning electron microscope/energy-dispersive spectroscopy, electron microprobe X-ray analysis (EPMA), ICP-mass spectroscopy, X-ray absorption near edge structure (XANES), small-focus XRF, and X-ray diffraction (XRD). These data indicated a wide range of Pt concentration from 150 to 700 ppb within a crust, though we found no distinct inter-element correlation or mineralogical control. Under the reflecting and electron microscope, no distinct Pt-bearing minerals or particles were identified. Small-focus XRF indicated no uneven distribution in any particulate matter, but all areas are less in abundance than the detection limit of about 10 ppm. Our tentative conclusion is that zero valence Pt0 (as suggested by XANES) is dispersed in the form of submicroscopic material most probably within ferromanganese minerals, and therefore, Pt-rich mineral particles may not be a major carrying phase.

Jan 1, 2005

By Richard H. T. Garnett

Marine mining on the continental shelf was first attempted in 1900 for gold off the beaches of Nome, Alaska. Attempts continued until 1990 with cutter-suction, airlift and bucket-ladder dredges. Offshore Thailand profitable production of tin resulted from clamshell, bucket-ladder and trailing suction hopper dredges. Today in Indonesia numerous bucket-ladder dredges continue to mine tin. Off the coast of Namibia and South Africa nearly a dozen large and medium sized vessels are engaged in diamond production. The obvious risk results from the working environment. Vessels and lives have been lost in the past. At best the availability of mining equipment is reduced. Leaving aside the marketing and financing aspects, otherwise the most important risks are technical. They manifest themselves as diamond production short-falls with obvious financial consequences. Bias and deficiencies in sampling equipment and procedures may result in misleading grade estimates, even serious under-estimation. Inadequate sampling in terms of sample support and density may result in over-optimistic grade determinations, especially if under-sized mining blocks are outlined. Quantitative measurement of the geotechnical characteristics of the sediments to be mined is an essential stage in a feasibility study. Without a full understanding of the bedrock profile and the overlying sediments the ease, completeness and speed of excavation during the mining process cannot be properly estimated. Both historically and at present the greatest negative discrepancies from production estimates result, not from grade shortfalls, but from significantly lower mining rates than thought possible by the operators. The learning curve in marine, production mining is steeper and longer than is generally recognised by newcomers to the industry. Examples are provided from tin, gold and diamond mining experiences.

Jan 1, 1998

By John W. Padan

The 1982 United Nations Convention on the Law of the Sea contains major provisions that U.S. negotiators have sought for over two decades. The internationally recognized right to the mineral resources of a broad continental margin is of potentially enormous future importance to the United States. Although water depths reach 10,000 feet in some of the deeper areas of the margin, technology is rapidly making those depths economically accessible. In 1997, production in the Gulf of Mexico will reach a world record water depth of 5400 feet. Of perhaps even greater importance to the oil and gas industry is the broadly acknowledged right for tanker transport of oil to take place throughout all parts of the world's oceans.

Jan 1, 1996

By RB. Pedersen, T. Barryere, E. Reeves, A. Stensland, I. Thorseth, T. Baumberger

Venting on ultraslow spreading ridges is far more abundant then previously predicted, and the discrepancy between observed and predicted vent field density may imply that non-magmatic heat sources are common along these ridges (Baker and German, 2004; Escartin et al., 2008; Rona et al., 2010; German et al., 2016). In this study we have estimated the flux from two hydrothermal vent sites situated on the slow to ultraslow spreading Mohns Ridge at the Arctic Mid-Ocean Ridge system (AMOR). The flux estimates have been made using the primordial isotope 3He in the non-buoyant plume above the Loki’s Castle vent field at the northern termination of the Mohns Ridge, and from the Jan Mayen vent fields area situated close to the southern termination of the ridge. Primordial 3He enters the oceans through degassing and mixing with hydrothermal fluids eventually to be discharged at the ocean floor primarily at hydrothermal vent sites and submarine volcanic eruptions (e.g. Clarke et al., 1969; Lupton and Craig, 1981; Lupton, 1998). Once introduced into the water column the concentration will only decrease by dilution due to its conservative behavior in the water column. Water column samples were collected using a CTD (conductivity, temperature, depth) probe (911plus Seabird) with a Niskin water bottle rosette. The water column above the Jan Mayen vent fields (JMVF) was sampled in the years 2006, 2011, 2012 and 2013 (82 samples) and the water column above the Loki’s Castle vent field was sampled in the years 2007, 2008 and 2009 (116 samples).

Jan 1, 2018

By Leonhard Weixler, Peter Platzek

The Company Bauer Maschinen is very well known in the field of specialist foundation equipment. In the diaphragm wall market, we have experiences both in manufacturing and executing projects all over the world since 1984. We have a population of more than 300 units working all over the world in all climate and soil conditions. Especially for hard soil and rock conditions, we have developed several cutting tools and systems to optimize the performance, e. g. the “flipper tooth” Besides the execution of land based foundation projects, we have performed our firs offshore project with the trench cutter in 1994. Our task was to take samples out of the alluvial soil off the coast of Namibia in a water depth of max. 200 m. We converted a drill vessel and launched the cutter thru the moon pool. The samples had a cross section of 3,40 m² and a max. depth of 5 m. They were used to estimate the content of diamonds. The first time, we reached the seabed of the deep sea was together with our seafloor exploration rig MeBo, where we can take cores up to a length of 160 m in a maximum water depth of 4000 m. With our customer MARUM, we have done several expeditions since 2005. The last expedition took place in the Black Sea to explore gas hydrates.

Jan 1, 2018

By Frans van Grunsven, Cees van Rhee, Geert Keetels

One of the obstacles during the initial phases of project development is the assessment of the environmental impact. Mining residue, consisting of fine seafloor sediments, are to be discharged subsea to mitigate the impact of these suspended particles. In order to test the effectiveness of discharging in proximity of the seabed, a numerical model is developed within the open source software package OpenFoam. Dedicated laboratory experiments for numerical model validation are discussed within this paper. INTRODUCTION Siltation is considered one of the major pressures on the environment for a seabed mining operation. Siltation is defined as the pollution of water by a high concentration of suspended sediments like clay or silt. This can be caused by two main activities during the mining process: the spill loss during the excavation and the return flow of undesired seafloor sediment after ore filtration on the ship. In a concentrated cloud, these fine particles form a so-called turbidity plume. Prediction of the size of these plumes and the created layer thickness of deposited sediment is a crucial part of the environmental impact assessment. The challenge in predicting the behaviour of these plumes is found in the wide range of scales involved in the process. At the point of origin, the turbidity plumes spread mainly under the influence of turbulent whirls created by an initial momentum and a buoyancy difference due to the presence of the suspended sediment particles. If carried by ambientcurrents, these plumes can spread for several kilometres before blending in the background.

Jan 1, 2018

By Chan Min Yoo, Kiseong Hyeong, Inah Seo

INTRODUCTION One of the major concerns for deep seabed mining is its environmental impact, from the disturbance of benthic communities due to the mining activity to the disposal of mine tailings back to the ocean. Yet a significant amount of waste materials would be produced from the on-deck processing on the mining platform, all the materials that produced on the mining platform are to be shipped to the land unless the related regulation and guidelines are developed by IMO and ISA (ISA, 2018). Still, ecotoxicology data for the deep seabed minerals from case studies in deep-sea tailings disposal (DSTD) and submarine tailings disposal (STD) sites are lacking and all other related aspects are also largely unknown. This year, the Republic of Korea has started a research project for the more comprehensive understanding of chemical and physical properties of mine tailings from the on-deck processing and the possible environmental impacts on the marine organisms after its disposal. Based on the scientific data collected from this project, Korea would be able to make recommendations for the methods and technical standards for the deep seabed mining discharges. The subjects of this project are threefold: to understand the physical/chemical properties of the tailings, to model the dispersion of particulates after the disposal, and to assess its impact on the marine ecology. Laboratory Experiments Producing Mine Tailings First, the possible waste materials are produced by mimicking the collecting and dressing processes at sea. The polymetallic nodules (PN) would be mined by using a collector lifting the crushed nodules out of the bottom sediment, and the bottom water, accompanying sediment, and the fine nodule particles which are too small to be recovered would be discharged to the ocean and thus are considered as tailings (Schriever and Thiel, 2013). In the laboratory, PN is crushed into the fragments smaller than 2 cm, abraded in the water using the rock mill, and then sieved to obtain the fine particles to be disposed.

Jan 1, 2018

By Charles L. Morgan

"In 2012 the International Seabed Authority (ISA) established nine “Areas of Particular Environmental Interest” (APEIs) for consideration as future Marine Protected Areas to help preserve the biodiversity of life on the seabed within the Clarion-Clipperton Zone (CCZ) between Baja California, Mexico, and the Hawaiian Islands. The CCZ is believed to have a high potential for future seabed mining operations. Areas under active exploration contracts in the CCZ, plus the areas currently reserved by the ISA for exploration by developing nations, comprise about 1.9 million km2 of seabed area. The currently designated APEIs consist of more than 1.4 million km2 of seabed. Each APEI includes a central primary conservation area of 200 X 200 km, surrounded by 100-km buffer areas on all sides. The 100-km buffers are intended as a very conservative spacing between the primary conservation area and potential mining activities in adjacent seabed. The selection of these nine 400 X 400 km APEIs, has been criticized as possibly not including sufficient representative habitat similar enough to the potential mining areas (identified currently as the exploration contract and reserved areas administered by the ISA within the region) to ensure protection of the biodiversity that might be impacted by mining.An area to the east of the existing exploration contracts and reserved areas is known to have substantial mineral deposits; it is very similar to the adjacent exploration contract areas in its geology, environmental setting, polymetallic nodule abundance and nodule metal content. Because it is located in the northeastern extreme of the CCZ, this area is also likely to have relatively high densities of benthic life, compared with benthic communities further westward within the CCZ. Many options for the designation of this APEI are possible, but the area designation must accommodate the boundaries of the Exclusive Economic Zones of Mexico and France.This paper discusses why the selected region in the eastern extreme of the CCZ is a good candidate for designation as a new APEI.Keywords: polymetallic nodules, Marine Protected Areas, Clarion-Clipperton Zone, Areas of Particular Environmental Interest"

Jan 1, 2017

By C. Wildman

Prospectivity modeling of seafloor massive sulphide (SMS) deposits has been completed over the Kermadec Arc-Colville Ridge area using the GIS based weights of evidence and fuzzy logic modeling techniques. SMS deposits are the current equivalent of ancient onshore volcanogenic massive sulphide (VMS) ore deposits. These high-grade deposits are formed on the seafloor and commonly consist of a black smoker and metal rich sediment mound complex resulting from the discharge of hydrothermal fluids (up to 400°C) from fractures on the seafloor. Metal sulphides are continuously precipitated in response to mixing of high-temperature hydrothermal fluids with ambient seawater. Accumulation of metal sulphides has led to SMS deposits being potentially major sources of copper, zinc, lead and other metals such as gold, silver, which to date remain untapped. Modeling of SMS deposits was undertaken to illustrate the power of GIS modeling for seafloor resource evaluation and how it can be used to quickly identify and rank in terms of the most likely prospective areas of the seafloor where new SMS deposits might exist. The mineral deposit modeling was constrained by the mineral systems concept which defines those parts of a mineralisation system that are critical to the ore-forming process. The deposits are typically formed in extensional tectonic settings, including both submerged tectonic margins and sea-floor spreading. Volcanic vent systems and underlying dykes, stocks and sills are the sources of heat that are responsible for converting sea water drawn down through fractures in the oceanic crust into an ore-forming hydrothermal fluid. This fluid is then capable of leaching metals and elements from surrounding footwall rocks, which are then transported upwards via the convection of hydrothermal fluids. The ore materials are then precipitated within the black smoker field as massive sulphides due to the mixing of high-temperature (250-400°C), metal-rich hydrothermal fluids with cold (about 2°C) oxygen bearing seawater.

Jan 1, 2011

By Cornel E. J. de Ronde

Brothers volcano (34°51.7?S, 179°03.6?E) is a large caldera volcano that forms part of the active Kermadec arc south of 32° S, NE of New Zealand. It is an elongate edifice striking NW-SE that is ~11-13 km long by 7-8 km across. The caldera has a basal diameter of 3-3.5 km and is surrounded by 350-450 m high walls with the floor 1,850 m deep. A volcanic cone of dacite composition rises 350 m from the caldera floor and partially coalesces with the southern caldera wall. Much of the caldera construction and the location of the hydrothermal vent sites are controlled by intersecting basement structures. Three hydrothermal sites have been recognized at Brothers; NW caldera, SE caldera and cone. Multiple hydrothermal plumes were mapped from the bottom of the caldera upwards to a depth of 900 m and originate from two of the sites; one on the NW caldera wall the other atop the cone. Analyses of these plumes show that the two vent sites are chemically distinct. The cone site itself hosts three distinct vent fields (summit, upper flank, NE flank) that in 1999 had plumes (mainly from the summit) containing relatively high concentrations of gas with a shift of -0.27 pH units (proxy for CO2) and H2S concentrations up to 4,250 nM, particulate Cu (PCu) of 3.4 nM, total dissolvable Fe (TDFe) of 4,720 nM, TDMn up to 260 nM and Fe/Mn values between 4.4 and 18.2. However, in 2002 plumes from the summit vent field had noticeably lower concentrations of PCu (0.3 nM), TDFe (175 nM), and Fe/Mn values of 0.8, although similar TDMn (220 nM) and shift in pH (-0.22) suggesting a state of flux for this site. By contrast, plumes originating from the NW caldera site have much less gas with a pH shift of -0.09 units and no detectable H2S, TDFe up to 955 nM, TDMn up to 150 nM, and Fe/Mn values of 6.4, and have not changed their composition over the same three year interval indicating a more chronic hydrothermal system. Plume d3He results show helium is decoupled from more near-surface vent fluid sources although a shift in R/Ra values from 6.1 ± 0.5 in 1999 for the combined vent sites to 7.2 ± 0.1 in 2002 indicates a less radiogenic input of helium over three years, suggestive of a greater magmatic input to the system.

Jan 1, 2004

By Andrea Koschinsky, Luise Heinrich

(for an oral presentation) Activities for preparing future deep-sea mining offer the unique opportunity to study environmental conditions and anticipate adverse environmental impacts prior to the commercialization of the activity. Until know, environmental research has first and foremost focused on understanding direct impacts occurring at the seafloor or in the water column such as the removal of substrate, the suspension of sediment or the creation of particle plumes. Impacts occurring above the sea surface have thus far rarely been considered. The operation of deep-sea mining equipment, as well as of mining and transport vessels will be associated with a considerable energy demand. In the open ocean, this energy will be provided by heavy fuel oil (HFO), which is the cheapest and most common marine fuel. The combustion of HFO will be associated with the release of greenhouse gases and other pollutants. Deep-sea mining will thus directly add to already critical air pollution levels caused by international shipping. To contribute to a holistic assessment of deep-sea mining impacts and to address the previously outlined knowledge gap, we present the methodology to quantify the fuel consumption and associated emissions of a potential typical commercial manganese nodule mining operation in the Clarion-Clipperton Zone (Fig.1). Using the mine set up and energy demand estimates from a study commissioned by the German Federal Ministry of Economic Affairs and Energy supplemented by information from literature, we anticipate emissions of carbon dioxide (CO2), carbon monoxide (CO), methane (CH4), nitrous oxide (NO2), nitrogen oxides (NOx), sulfur oxides (SOx), particulate matter and non-methane volatile organic compounds.

Jan 1, 2018

By Chan Min Yoo, Jung-Keuk Kang, Wonnyon Kim

Recently high-resolution paleomagnetic age determination of ferromanganese crust in less than millimeter scale has been successfully carried out using a superconducting quantum interference device microscopy magnetometer (SMM). However, it has not been clearly identified how the crust is keeping ancient geomagnetic field records. Here we try to identify magnetic mineralogy of the crust obtained in the Magellan Seamounts, the West Pacific (~20 °N). As a record, age of the crust used in this study is extended to ~10 Ma at ~40 mm depth and ~28 Ma at ~100 mm depth, respectively, based on the combination approach of SMM measurements, Be-isotope and Co-chronology. Thermal demagnetization revealed a Curie temperature of ~560oC, corresponding to (titano)magnetite. Component analysis of isothermal remanent magnetization identified a presence of two types of magnetite. Measurements of first order reverse curve showed a dominance of non-interacting single-domain magnetite, which is one of the intrinsic feature of biogenic magnetite. Although most of the magnetic particles on transmitted electron microscopy are covered by amorphous Fe-Mn minerals, some are observed as a prototype of biogenic magnetite showing a chain of ~10 nm sized magnetite cubes. However, a magnetite signal (i.e., Verway transition at ~ –120 oC) was not detected in low-temperature treatment probably due to surface oxidation of magnetite. Contribution of interacting magnetite of detrital origin is <30% throughout a crust. Interestingly, contribution of detrital magnetite is almost three times higher since ~10 Ma. At this boundary, a growth rate of the crust is double up and flux of other detrital signals, including Al, Mg, Ti and Zr, are also increased.

Jan 1, 2017

By Campbell McKenzie

Substantial consideration has been given to the implications that the morphology of the Chatham Rise deposit will have on mining operations. The glacio-tectonic processes involved in the distribution of nodules on the rise has in several areas been quite significant. The recent cruises by Chatham Rock Phosphate Limited (CRPL) have collected data which has affirmed the assumptions previously made and catered for in historic resource estimations. The deformation and displacement of the phosphorite during glacial periods and the redistribution of the mobile sand during interglacial periods is interpreted to have produced a highly variable pattern of phosphorite concentration (kg phosphorite/m2) and coverage (% phosphorite/sample weight). The phosphorite resource probably has a significant spatial variability at a scale of tens of metres. Results of recent surveys show phosphorite-rich patches alternating with phosphorite-poor areas at distances of less than 20 m. The high spatial variability of the deposit has had a bearing on how historical information for the project has been regarded and integrated with the recent exploration approach and data collection process. This coupled with the proposed extraction tool has influenced the size, nature, extent and siting of the proposed mining blocks

Sep 14, 2011

By Ian Selby

Resource management is a key factor in the operation of a successful marine aggregates business; it is integral to the development of sustainability, satisfying increasing commercial, quality, and environmental performance standards. Resource management is based on the combination of; (i) a thorough evaluation and understanding of the resources on the sea bed and (ii) a dredging plan targeted to permit the effective and efficient extraction of the resources whilst mitigating impacts and leaving the sea bed ready for recolonisation.

Jan 1, 2004

By Alexander Malahoff

An international research team working through the Hawai?i Undersea Research Laboratory (HURL) undertook a bold challenge to explore the chemistry, geology, mineral formation and superheated hydrothermal vents of the Kermadec Island Arc. With the mothership, R/V Ka?imikai-o-Kanaloa, scientists from six research institutions explored the active submarine volcanoes stretching over a line of volcanoes 1,000 miles long between Samoa and New Zealand. The expedition left Hawaii on the 18th of March 2005 and returned on the 5th of August having covered a distance of 10,000 miles between Hawaii and New Zealand. Scientists from the USA, New Zealand and Germany used the HURL submersibles, Pisces IV and Pisces V, as well as the remotely-operated vehicle RCV-150, aboard the R/V Ka?imikai-o-Kanaloa to dive into active volcanoes to water depths of 2,000 meters. Scientists from New Zealand, the USA and Germany conducted 41 dives on the previously unexplored (from manned submersibles) submarine volcanoes. Ten active volcanoes were explored during this time. Hundreds of specimens of new and unusual marine life, water chemistry, extremophile microorganisms, mineral formations and volcanic rocks were collected during this expedition with the two submersibles and the ROV. Bizarre natural events, such as the oozing of hot liquid sulfur from the ocean floor onto the skids of the submersible were observed. Carbon dioxide gas was observed profusely streaming into the seawater from the volcanoes, making these one of the greatest contributions to hot house gasses entering the atmosphere.

Jan 1, 2005

By Kioshi Mishiro, Pratima Jauhari, Walter Williams

INTRODUCTION The UN-General Assembly adopted an Agreement on 28 July 1994 entitled ‘Agreement relating to the implementation of Part XI of the United Nations Convention on the Law of the Sea ((UNCLOS) of 10 December 1982’. The Agreement came into force on 16 November 1994, and consequently, the inauguration of the International Seabed Authority (ISA, or the Authority), located in Kingston, Jamaica. The Authority is the organization through which States Parties to the Convention (168, as of 25 July 2017) shall, in accordance with the regime for the seabed and ocean floor and subsoil thereof beyond the limits of national jurisdiction (the Area) established in Part XI and the Agreement, organize and control activities in the Area, particularly with a view to administering the mineral resources of the Area. The legal regime for the administration and development of the mineral resources of the Area as it now exists are available in Part XI of the Convention1 which contains the legal framework governing “activities in the Area” and in Annex III to the Convention which contains the “Basic Conditions of Prospecting, Exploration and Exploitation” with respect to the resources of the Area2. The 1994 Agreement relating to the Implementation of Part XI of the UNCLOS is the so- called ‘parallel system’; as elaborated in article 153 of the Convention. The essential elements of the ‘parallel system’ include assured access for States parties and their nationals to seabed mineral resources along with a system of site-banking, whereby ‘reserved areas’ are set aside for the conduct of activities by the Authority through the ‘Enterprise’ itself or in association with developing States or in joint venture with the contractor who provided the particular reserved site2.

Jan 1, 2018

By Graham Singleton

Around 235 million tonnes of marine aggregates have been dredged in the last decade from the UK continental shelf alone. The current distribution of marine aggregate production licence areas in North West Europe reflects the relationship between a variety of factors such as the natural distribution of deposits of sand and gravel, the demand for aggregates, the technical capabilities of the dredging fleet and environmental considerations. Whilst the sand and gravel deposits targeted by the marine aggregate industry are generally relict and therefore geographically fixed, the remaining factors have evolved over time and will continue to do so in future. Applications for new licences must not only reflect the current situation, but anticipate future trends. The main markets for marine aggregates are the construction industry, centred around the larger centres of population and coastal protection projects along the coastline of Europe. The aggregate industry as a whole does not create demand but simply meets it. Many factors influence the overall demand for aggregates and guidance exists for those in authority and industry who need to plan for the supply of aggregates. Adequate supplies should be maintained at the best balance of social, environmental and economic cost, whilst ensuring that extraction and development are consistent with the principles of sustainable development.

Jan 1, 2004

By Cheng Xiangzhou

The China Ocean Mineral Resources Research and Development Association (COMRA) conducted a topographic survey in its deep seabed claim area with the SeaBeam system in 19475. After analyzing the data, it was determined that there is a group of living things several hundreds of meters in depth that significantly affect the sound waves in the frequency range of interest. We will attempt to investigate more about such influences. Physical model testing is an important means for studying the theory, and for development of the technology for geophysical prospecting. Because the manganese nodules are distributed over the sea floor in irregular patterns, it is hoped that study of the acoustic properties of manganese nodules by means of physical model testing can improve interpretation of the data of the multi-beam system and the SeaBeam system. This will provide a more reliable basis for delimiting the mineral site and evaluating the reserves in the Pioneer area of China.

Jan 1, 1996

By Wenbin Ma, Cees van Rhee, Dingena Schott

Since the concept of deep sea mining (DSM) was proposed by J. L. Mero with his book, The Mineral Resources of the Sea, in the 1960s, many research and significant developments have been implemented. However, its commercial mining process still has not yet commenced. One of the most important issues is that a sustainable DSM transport plan is difficult to determine, taking into consideration the DSM technological, economic, and environmental aspects simultaneously. The objective of this paper is to propose a method to determine the sustainable DSM transport plan utilizing a fuzzy analytic network process method, which is a typical multi-criteria decision making method (MCDM). The DSM transport plans evaluating major criteria consist of technological, economic, environmental, and social aspects with both qualitative and quantitative attributes. Different major criteria include several sub-criteria, respectively:  Technological aspect: energy consumption, proven technology, technology reliability, production rate, technology availability;  Economic aspect: gross income, capital cost, operation and maintenance cost, investment recovery period;  Environmental aspect: species disturbance variance, severity of ill effect, turbidity of ocean water, total organic carbon content, sedimentation thickness;  Social aspect: social acceptability, policy support; The weights for all evaluating criteria and sub-criteria are determined through a questionnaire survey interviewing experts at different research fields. All the transport plan candidates are ranked based on a comprehensive index. The conducted research in this paper is meaningful to promote the DSM commercialization process.

Jan 1, 2018

By Peter E. Halbach

The Central Indian Ridge (CIR), the boundary between the African and Indian plates, forms a SSE trending mid-oceanic accretionary system in the equatorial Indian Ocean (Fig. 1), extending to the northerly Carlsberg Ridge spreading center, and terminating at the Rodrigues Triple Junction (RTJ; 25°30&apos;S, 70°06&apos;E) by intersection with the Southwest Indian Ridge (SWIR) and the Southeast Indian Ridge (SEIR). Crustal divergence of the CIR proceeds at intermediate rates; a progressive increase of ocean floor accretion towards the south is documented: the present half spreading rate and ridge trend change from 1.80 cm/a and N142° at the equator to 2.73 cm/a and N152° north of the triple point. The topography of the central rift zone is rather smooth compared to slow spreading analogues such as the SWIR, but slightly more rugged than the SEIR. The rift valley is 500-800 m deep, 10-15 km wide and usually well defined. The inner floor, 2-4 km in width, is relatively flat along the axis and more variable in cross section, and lies at 2700-3200 m depth. Off set fracture zones striking generally N60° . in southern portions of the CIR and laterally displacing median valleys by as much as 8 km are often bent, uplifting crustal sequences up to several hundred meters. The length of individual spreading segments varies between a few and several tens of kilometers. The vertical displacement on normal faults are larger while lineaments are shorter than those of the faster spreading SEIR. The direction of lineaments measured on the southwestern and northeastern flanks of the southern CIR are N154° and

Jan 1, 1994