Search Documents

By Miguel Becerra, Daniel Jordán, Jorge Soto, Luis Torres

"Most SAG grinding operations currently use ball sizes between 5.5 and 6 inch maximum size. However, in most cases the use of this ball sizes hasn’t been justified by a phenomenological analysis of the real effect on the grinding process, but rather by trial and error. The analysis of the influence of ball sizes in SAG grinding hasn’t been developed in detail by considering the effect on process parameters inside the mill, grinding efficiency or internal classification. Historically a conventional grinding reference has been made on the empirical procedure developed by Azzaroni (1980). Further to Azzaroni’s methodology, Sepulveda (Sepúlveda, 2007) developed the SPEC methodology, incorporating the ball size effect on the grinding efficiency parameters using a population balance model included on Molycop tools spreadsheets.This paper demonstrates a detailed analysis at pilot scale of the ball size employed in SAG grinding and scaling that exists between the different levels. This analysis includes assessing the effect of balls sizes on parameters associated with grinding efficiency and its effect on the total fill level, product size distribution and specific energy consumption, among others. In a complementary way it develops a technical - economical evaluation from industrial data comparing two different ball sizes and its effect on the grinding process analysed integrally."

Jan 1, 2014

By T. Inoue, K. Okaya

"Movement of mill charge in the centrifugal mill is essentially different from that in the vibration mill with circular path despite the apparently similar mode in the motion of mill body. As proved e.g. in [11], this results in substantial advantage regarding the comminution intensity of the centrifugal mill over the conventional vibration mill accounting approximately to one order of magnitude.Back in 1983, Bradley et al. presented a model of the centrifugal mill based on the kinetics of the mill charge by regarding it as a lumped mass. On the other hand, numerical modeling by ‘discrete element method (DEM)’ enabled us to observe the movement of each ball in the centrifugal mill with an extremely minute time intervals (Inoue et al., XX IMPC in 1997). The former approach rendered simple, even though approximate, expression of the mill behavior, while the latter method was advantageous in describing the behavior of the mill in terms of individual events taking place in the mill body, even though the result did not reduce to a simple expression. The characteristics of the centrifugal mill described by both these approaches proved to be in a degree of agreement. Thus, the kinetic approach was capable of presenting the overall view of the mill, while the DEM model was informative of the details that could not be depicted well enough by the simple math expressions."

Jan 1, 2003

By Kr. J. Dedelyanova

Selective flocculation of iron minerals could improve the economics of high intensity magnetic separation as concomitant process. When the minerals are finely disseminated is necessary a finer grinding to be applied which generates a lot of slimes. The HIMS is not enough efficient for particles below 20 microns ? territory where the selective flocculation is already well known industrial practice, so the combination of these two methods of beneficiation can bring a higher grade at high recovery to be achieved. The dynamics and selectivity of the precipitation process is studied in batch tests with flocculant starch and dispersants sodium silicate and sodium hexametaphosphate. The influence of preliminary conditioning with nitrogen acid at pH 2 before flocculation is also investigated. Flowsheet including these two methods is tested and the distribution of iron is shown.

Jan 1, 2014

By A. P. Purgin, M. G. Viduetsky, I. F. Garifulin

"The combined treatment process for mine, tailings storage facility, quarry, circulating, and waste water in the mining and metals industry brings together the conventional chemical treatment processes and pneumatic flotation cells of the KFM series. The key principle of the process is preparing the water for treatment by saturating with finely dispersed air bubbles in the flotation cell blowers. Gas-air lift dispersers located in the lower part of the cell body additionally saturate the cell’s contents with finely dispersed air. Due to the residual content of flotation agents in the treated water, hydroxide ion-air aggregates form at the aerator outlet, supporting the efficient precipitation of hydroxide ions of heavy non-ferrous metals, calcium and magnesium ions. This process was tested in the pilot plant KFM-180 with a raw (untreated) water capacity of up to 18 m3/h per 1 m3 of the flotation cell volume using a mixture of the tailings storage facility and mine water from JSC Safyanovo Copper. The treatment process included raw water treatment with lime, aeration in KFM cells, and filtration in a sorbent bed. The content of metal ions in the treated water is lower than in the feed water by a factor of up to 170,000 and approaches the standards: aluminum 0.016-0.02 mg/l, copper 0.0043-0.0045 mg/l, zinc 0.049-0.052 mg/l. circulating water of Soryin Tailings Storage Facility at JSC Svyatogor. The treatment process included raw water treatment with lime and alkali, aeration in KFM cells, and filtration in a sorbent bed. The content of metals in the treated water is lower than in the feed water by a factor of up to 9000: copper 0.022 mg/l, zinc 0.012 mg/l, iron 0.012 mg/l, manganese 0.015 mg/l, nickel 0.132 mg/l, arsenic 0.016 mg/l. Water hardness is significantly lower: calcium - 12.6 mg/l, magnesium - 1.1 mg/l. This process can be used in the treatment of mine, quarry, tailings storage facility, and circulating water at mining and non-ferrous metals projects."

Jan 1, 2018

By Katja Ohenoja

Polymer dispersants, also known as grinding aids, are widely used to reduce the viscosity of mineral particle suspensions and to improve energy efficiency during fine grinding. In this study, the effect of polymer dispersant with different molecular structure on the suspension properties in the wet stirred media milling of limestone was studied. The stability of suspension was studied by combining rheological and zeta potential measurements. The PDI value of polymers corresponds to the width of the molecular weight distribution so that low PDI corresponds to narrow MW distribution and high PDI to the wide one. In this study, two traditionally fractionated polymer dispersants with high PDI (over 2) and one novel polymer dispersant with low PDI (1.2) has been tested. It was noticed that dispersants worked as electrosteric stabilizators and prevented the agglomeration of ground limestone particles. The uses of dispersants could increase solids concentration used in the grinding experiments and at the same time lower the particle size and specific energy consumption. The obtained particle sizes were about 1 µm regardless of which dispersant was used or the amount of it. The novel dispersant with low PDI reduced viscosity most when compared with the traditionally fractionated polymer dispersants. Results indicated that even higher solids concentrations can be used at the same amount of dispersant when the novel low PDI polymer dispersant is used. Alternatively, lower dosage of novel low PDI dispersant can be used compared to traditionally fractionated dispersants.

Sep 1, 2012

By L. S. Bbosa

Single particle impact breakage experiments provide essential data to aid in understanding of rock fracture in comminution. Such experiments, conducted using devices such as the drop weight tester, split Hopkinson bars and more recently the rotary breakage tester, have been successfully used to characterize ore breakage properties in relation to measured fracture energies. The work presented in this paper highlights the techniques behind the calculation of impact breakage properties from each of these three devices. The breakage parameters that can be calculated from experimental data from each of these are to be described. Drop weight tests are used to calculate A and b hardness parameters using the standard JK breakage model. Split Hopkinson pressure bars are used to establish the ultimate compressive stress of particles through single impact breakage tests and the fraction of impact energy utilized to cause particle fracture. Low energy breakage tests using the rotary breakage tester are shown to be used in calculating particle breakage probability. Methods to calculate parameters related to particle breakage probabilities such as E0 and Ecrit are also discussed.

Jan 1, 2014

By C. Dorfling, W. A. Rossouw

"Hydrometallurgical processes used for metal recovery from waste printed circuit boards (PCBs) typically involve dismantling, shredding and physical separation prior to successive leaching stages for selective dissolution of different metals. The principles of the physical separation units are well understood, but valuable metal losses of more than 30 % can be incurred during these processing steps. The impact of the physical separation units’ performance on downstream leaching operations have not been defined; this prevents the development of a well-integrated process. The objective of this project was to determine to what extent the base metal leaching behavior depends on the physical separation pre-treatment. PCBs were shredded to 100 % passing 2 mm before physical separation by dense medium separation (DMS) as well as magnetic separation. Batch leaching tests using various concentrations of sulfuric acid were conducted on three feed fractions: (1) shredded PCBs without any physical separation, (2) heavy fraction recovered from DMS, and (3) non-magnetic fraction recovered from the DMS heavy fraction. DMS increased the metal content in the feed from 48 % to 75 % on a mass basis, but 70 % of the gold and 20 % of the copper reported to the light fraction. The application of magnetic separation to the heavy fraction produced by DMS removed 67 % and 61 % of the iron and nickel, respectively, while negligible amounts of non-magnetic metals were removed. Although DMS successfully concentrated the feed and magnetic separation removed the majority of iron and nickel, these steps did not result in any improvement in the rate or extent of copper leaching. Metals generally leached faster when the sulfuric acid concentration was increased from 1 M to 2.5 M; this effect was seen to be more pronounced for pretreated feed. INTRODUCTION The fast rate of technological development has led to a decrease in the service life of electronic devices. This is resulting in an increased rate of electronic waste generation. The recovery of metals from electronic waste is of environmental and economic interest. The majority of these metals are typically located on printed circuit boards (PCBs) within electronic devices (Tuncuk, Stazi et al., 2012). Hydrometallurgical processes are considered a viable option for small scale metal recovery from waste PCBs, and generally involve the following steps: disassembly for removal of hazardous and reusable parts, size reduction, physical separation, successive leaching stages for metal dissolution and finally recovery of metals from leach solutions."

Jan 1, 2018

To extract the gold from refractory gold concentrate with high sulfur and arsenic, the gold concentrate was catalytically oxidized to expose the gold for cyanide leaching. The effects of reaction temperature, initial nitric acid concentration, reaction time and initial gold concentrate concentration on the conversion rate were studied. The results show that the appropriate conditions for the catalytical oxidation of this gold concentrate are: reaction temperature of 65 oC; initial nitric acid concentration of 25% (wt.); reaction time of 1.5 hours; initial gold concentrate concentration of 10% (wt.). Under such conditions, the conversion rate of gold concentrate is 92%. The solution can be used to prepare nano-iron oxide red pigment. Gases released in the process can be recycled and reused by oxidation absorption. A chemical background of catalytic oxidation is proposed.

Jan 1, 2014

By Xiao Ni

Alkyl hydroxamic acid was shown to be a suitable collector for the flotation of pyrochlore from carbonatite niobium oxide ores. In the direct batch rougher flotation from the ore without desliming, over 85% of the pyrochlore can be recovered at about 30% mass pull. Cleaner flotation tests showed that the rougher concentrate can be upgraded. The adsorption mechanisms of octyl hydroxamic acid (OHA) were studied by using high purity pyrochlore and calcite mineral samples and employing analytical measurements such as Fourier transform infrared spectroscopy (FTIR), X-ray photoelectron spectroscopy (XPS) and UV/VIS spectroscopy. FTIR showed a shift of the vibrational frequencies of the carbonyl group in hydroxamic acid after adsorption on pyrochlore and calcite, and the shift was more pronounced on pyrochlore. XPS results indicated a lowering of the binding energies (chemical shift) of Nb3d5/2 and Ca2p3/2 electrons on pyrochlore, and the lowering of the binding energies of Ca2p3/2 electrons on calcite, again with the shift being more pronounced on pyrochlore. The results indicated hydroxamic acid formed stronger complexes with pyrochlore than with calcite. Adsorption isotherms indicated that OHA adsorbed more on pyrochlore than on calcite at low concentration. At high concentrations, the adsorption densities on both minerals were similar. All results explained the observed selectivity of the reagents in the flotation of the carbonatite niobium oxide ores.

Sep 1, 2012

By Vishal Shukla, Ashok Kumar, C. Raghu Kumar, D. P. Chakraborty

"Traditional iron ore beneficiation plants using washing, screening, and jigging processes require large volumes of process water. Generated slime during processing, its disposal and impact on water usage, is an important concern for any mining company. The challenge today, during extracting iron ore, is how to dispose of slime such that it is contained and stable, while maximizing water reuse and minimizing surface footprint. The slime disposal methods are sensitive to the environment. Two major technologies presently being practiced for disposing the slime across the world are pressure filtration and paste thickening. In this perspective an attempt has been made to do comparative study between paste thickening and pressure filtration for selection of suitable slime disposable technology for Noamundi processing plant, Tata Steel. From the studies, it is evident that by adopting pressure filtration technique it was possible to produce filtered slime, whereas filtration, rate reduces significantly with the presence of finer fraction. Further , the greatest advantage of paste thickening is volume reduction of slime. By considering the technology limitation and comparative lab test work result, it is opined that combination of filtration and paste thickening technology is favorable in terms of capital and operating cost and slime >45 µ should be filtered and < 45 µ slime should go for paste thickening. The study and the results are presented in details.INTRODUCTION The beneficiation processes always end up with an enriched portion of desired mineral - “Concentrate” and an enriched portion of undesired minerals - “Tailing”. The proportion and nature of tailings generated in every beneficiation process differ from ore to ore and reflects the characteristics of the feed processed. The traditional method of tailing disposal in many mineral processing industries has been to dispose them as thickener underflow at around 35% solids. Though, it had certain advantages of transportation with ease but contribute to a greater volume occupied in the tailing dam. This sustained practice and failure to utilize the space available in the tailing dam judiciously endangered the mining industry. The tailing management has become the toughest task to the mining industry and most of the mines are running out of space for disposing the fresh tailings as many of these are at the verge of getting filled."

Jan 1, 2018

By C. A. Acuña

Extensive literature exists on the motion of single bubbles and the behaviour of swarms of bubbles. This contribution describes work to track and reveal the motion of individual bubbles in a swarm. The technique is based on high speed cinematography and tracking of multiple moving objects. Image processing algorithms were implemented in Matlab to isolate and measure geometric proper-ties of the bubbles in image sequences recorded at 2 ms interval; and these properties were compiled into a data structure. To track a bubble, the geometric properties and a matching criterion were applied on consecutive pictures to identify the bubble. The bubble trajectory was reconstructed from the data structure for the matched objects. The methodology is briefly described. The new technique was tested for bubbles produced at slot-type spargers (i.e., approximately 2-D swarms) in the presence of two frother types (&apos;strong&apos; and &apos;weak&apos;). Two observations are discussed: a) that bubble motion in a swarm describes a velocity-size relationship dictated by the dominant bubble size class; and b) that surfactant type influences bubble rise velocity for bubbles in the range 0.1 mm to 4 mm. The latter suggests surface viscosity rather than surface immobilization determines bubble rise velocity.

Jan 1, 2014

By P. Huang, D. W. Fuerstenau

Various factors that control the natural flotability of talc, including differences due to crystal face and edge effects, were delineated. For study of talc depression phenomena, dextrin was used as a model depressant. For the enhancement of talc flotation, dodecylammonium acetate (DDAA) was used as the collector. The interaction of DDAA with talc was assessed by flotation experiments and electrokinetic (zeta potential) measurements, from which the role of hydrophobic bonding can be demonstrated. The results presented in this paper provide useful information on how the crystal chemistry and surface chemistry control the electrical double layer, adsorption phenomena, wettability, and flotation behavior of talc in aqueous media.

Jan 1, 2003

By D. W. Fuerstenau

Understanding how cationic surfactants affect the interfacial behavior of quartz is important in mineral processing and environmental engineering. This paper presents the results of a study of the effect of the molecular structure of cationic surfactants on the interfacial behavior of finely ground natural quartz. Most of the experimental work involved the determination of zeta potentials and the stability of quartz suspensions. Some measurements of induction times and the flotation response of coarser particles are also included. How these surfactants affect interfacial behavior is discussed in terms of adsorption mechanisms. The molecular structure (number of hydrocarbon chains, type of ionic head group, number of ionic head groups on the molecule) of these reagents was found to significantly affect their surface activity.

Jan 1, 2014

By Thenepalli Thriveni, Seong-Young Nam, Nam-Il Um

New modern water treatment technologies required for arsenic removal from waste waters contaminated extensively by various background sources from mining, industrial waste, agricultural waste, painting industry and natural geological bed rock system etc. Arsenic is a widely dispersed element in the earth&apos;s crust and exists at an average concentration of approximately 5 mg/kg. Arsenic (As) and heavy metals may be released from the mine wastes to the ground and surface water systems, as well as the geological environment due to their solubility and mobility. This research focuses on the effect of accelerated carbonation process for successful removal of heavy metal arsenic anions from artificial waste water and mining waste waters. This accelerated carbonation process is a simple and novel method with 85 ~ 88% removal efficiency. Carbonation has been studied as a process to further improve immobilization of solidified/stabilized waste and granular waste. After successful removal of arsenic anions from solid mining waste and its potential benefits for producing construction materials. Besides, the industrial and urban management systems are generating bulk solid mining wastes, and most often dumping them in open fields. To prevent the landfilling with mining waste, many efforts are being made for the recycling of different types of mining solid wastes with a view to utilizing them in the production of various construction materials.

Jan 1, 2014

By Sathyaprasad Nanjundaiah

The Paper intends to showcase a framework for spatial data collaboration from multiple sources of data, in order to create a single source of truth across the Organization. The framework is targeted to reduce the data duplicity, re-work, time loss due to search of required data and hindrances to fetch or transfer data from various data sources. The spatial data collaboration will provide a single window view of the entire organization with respect to its operations, management, sales, customers and competitors on a spatial reference across various regions in the World. Large Organizations with cross-country operations can standardize the use of spatial data through this framework for ease of data access, increasing the data reliability / integrity and better / on time decision making. Keywords: spatial data, GIS, collaboration, framework, mining, ESRI, tab files, shape files, ETL, reliability, integrity, interoperability, geo data, geo database, single source of truth

Sep 1, 2012

By N. S. Phala

Declining gold grades, mineralogical complexity of ore bodies, increasing input costs, more stringent conditions in the licenses to operate, and uncertain gold price dynamics combine to exert significant ongoing pressure on margins of gold producers. Innovative approaches of extracting the metal from its ores are required to realize value from existing and future assets. In a conventional gold processing plant, size reduction of mined ore to produce floatable or leachable product is a significant cost contributor. A step change in cost reduction will be attained if radically energy efficient grinding approaches can be developed, replacing tumbling mills. In the path towards that goal, some quick wins are possible through waste rejection before grinding, and pre-treatment of mill feed to reduce grinding energy demands. Gold locked in complex mineralizations puts pressure on margins by increasing cost per oz (typically high $/t and low metal recoveries) in the hydrometallurgical steps. Gold miners are primarily price takers. The current narrow range of gold uses (predominantly investment and jewellery) is not an entirely desirable state. Some diversification into commercial uses would potentially be a price stabilizer. In this paper, promising research directions, some not always fully explored in the gold metallurgy research space, are highlighted to stimulate radical innovation for substantial value enhancements. The author strongly believes a shift from a traditionally conservative and incremental innovation approach to a more aggressive one, across all aspects of the gold metallurgy value stream (processes to products), is what the industry needs. Keywords: gold metallurgy value stream, thiobaccilus ferroxidants, HPGR

Sep 1, 2012

By Massimiliano Zanin, William Skinner, Keith Quast

With the scarcity of fresh potable water on mining sites, particularly those in arid and remote regions, the use of sea water is being contemplated and actually used at a number of mineral concentrators worldwide. The use of sea water, with its associated high dissolved solids content and ionic strength will affect all aspects of processing (e.g. frothing and froth stability, buffering capacity for pH control, solubility of minerals and corrosion of media and equipment). Selective depression of pyrite is more difficult in sea water due to the increased lime addition to achieve a high pH. This results in a reduction in molybdenite recovery. The use of grinding media with various chromium contents and its effect on subsequent Cu and Mo flotation has been investigated in the current study, with both grinding and flotation testing conducted in artificial sea water. Pulp chemistry (pH, Eh and DO) have been logged during grinding, and flotation testing was conducted on subsequent slurries. The flotation results show that the system is remarkably robust and able to cope with wide ranges of pulp chemistry parameters. The effects of artificial sea water on the surfaces of minerals during grinding have been examined using X-Ray Photoelectron Spectroscopy

Jan 1, 2014

By Ljubisa Obradovic, Baisui Han, Batnasan Altansukh, Zoran Stevanovic, Atsushi Shibayama, Jonovic Radojka, Daizo Ishiyama, Kazutoshi Hag, Radmila Markovic, Ljiljana Avramovic

This paper discussed a combined froth flotation and high pressure leaching (HPL) process to recover copper from mine tailings. At first, froth flotation were carried out using the mine tailings sample under various conditions in the presence of different pH (3.5-10) and sulfurizing reagent value (0-1000 g/t), respectively. As a result, optimum condition (sulfurizing reagent of 1000 g/t, pH of 10, PAX (collector) of 100 g/t and MIBC (frother) of 200 g/t) was found for froth flotation of copper. The effects of sulphuric acid concentration, leaching temperature, total pressure (steam pressure plus oxygen pressure) on high pressure leaching (HPL) of mine tailing were investigated using sulphuric acid solution in the presence of oxygen. The best conditions for HPL were obtained to be sulphuric acid concentration: 0 mol/L (water), leaching temperature: 170 ?, total pressure: 2 MPa, leaching time: 1 hr and pulp density: 100 g/L. The leaching rate of copper reached nearly 99 % and the concentration of copper in pregnant leach solution (PLS) was 0.24 g/L. Finally, copper in the mine tailing was recovered using froth flotation followed by HPL. As a result of a combined froth flotation and HPL, the vast majority of copper (99 %) from the mine tailings was extracted.

Jan 1, 2014

By S. Gaydardzhiev

Laboratory batch tests having preliminary and orientation character aiming at improvement of the molybdenum flotation at Ellatzite copper processing plant in Bulgaria have been conducted. The following technological parameters have been screened to study their influence on the grade and recovery of copper and molybdenum during the rougher flotation stage: flotation pulp density, pH, addition of secondary collector and replacement of MIBC by pine oil as a frother. The results have shown that slightly better grade/recovery figures could be obtained for both copper and molybdenum at lower flotation pulp densities. The addition of kerosene has improved the recovery of molybdenum however, on the expense of that of copper. The effects from pH variation and the replacement of MIBC by pine oil as a frother have been almost negligible.

Sep 1, 2012

By H. R. Manouchehri

Large variations in flotation characteristics of minerals have been observed in winter and summer in plant practices as a result of changes in pulp temperature. Variations in temperature may affect the quality for pulp and related process water through changes in dissociation of different chemical species within the pulp, as well as changing in gas and metal hydroxide solubility, reagent adsorption and its stability on mineral surfaces, water/pulp viscosity, etc. All of these affect the flotation characteristics of specific mineral to some degree or another. It has been observed in Cu-Pb-Zn and/or Pb-Zn sulfides flotation that sphalerite (ZnS) flotation is strongly affected by changes in pulp temperature. Plant practices have shown that at the both low, e.g., T <10-12°C, and high, e.g., T > 60°C, the recovery for copper activated sphalerite is dramatically dropped. Within this paper the effect of pulp temperature on flotation characteristics of sphalerite is brought into considerations and laboratory flotation tests were conducted in conjunction with surface and solution chemistry analysis to understand the effect of temperature on sphalerite recovery. The effect of temperature seems to be complex since the temperature affects both the physical (hydrodynamics) and chemical phenomena in the flotation cell. In fact all sub-processes in flotation, i.e., collision, attachment and detachment, are affected by changing in temperature. Experimental results indicating that at alkaline pH values, e.g., 8.5 to 10.5, the recovery for copper-activated sphalerite is dramatically reduced when temperature is below 10-12°C, which is in agreement with plant practice at Boliden?s Garpenberg plant in Sweden. However, results from other studies indicated that the zinc recovery is also considerably decreased at high pulp temperatures, i.e., 62°C and above.

Sep 1, 2012