Search Documents

By L. J. Li, Q. Zhang, Z. H. Liu, Q. L. Chen

Phosphogypsum (PG) is an industrial waste from the production of phosphate fertilizer. The utilization of PG is restricted by its containing impurities, and the pretreatment is crucial to eliminating these impurities. The purpose of the research is to recycle pretreatment PG as raw material for preparation of a-calcium sulfate hemihydrate (a-HH) by salt solution method. The effect of pretreatment technologies of lime neutralization and washing on dehydration rate, phase composition and morphology evolution of a-HH were investigated by crystal water content analysis, XRD and SEM. Furthermore, the change of pH in the reaction process was also discussed in detail. The results show that the dehydration rate of conversion PG to a-HH increases and the corresponding induction period, crystal growth period and total time decrease with an increase in CaO dosage from 0.2% to 0.6%. In the presence of 0.4% CaO or 0.6% CaO, the a-HH presents a long hexagon-prism-shaped crystal with a purity of 94%, and the end face of a-HH presents polyhedron. The system pH sharply decreases with the reaction time under different CaO dosage, and the pH variation from the initial alkalinity to acidity. The main reason is that as the co-crystallized phosphorus dissolved and released HPO42-, and with the pH decreasing to 4-5, HPO42- transformed into H2PO4-. The dehydration rate of washing PG is lower than that of original PG. Compared with the original PG, a-HH with the larger width and smaller aspect ratio can be achieved from the pretreatment PG subjected to lime neutralization and washing, meanwhile the crystal surface is more smooth.

Jan 1, 2018

By D. Tao

A novel rotary triboelectrostatic separator has been developed and patented recently at the University of Kentucky with unique features, including a high efficiency rotary charger, charger electrification, laminar air flow, etc. A parametric study has been performed with a coal combustion fly ash sample to investigate the effects of major operating parameters on the process performance. Most significant operating variables and optimum conditions were identified. Separation tests performed with four fly ash samples indicated that the rotary triboelectrostatic separator showed effective fly ash separation.

Jan 1, 2014

By Tchingis Lekhatinov, Lev Filippov, Vyacheslav Severov, Alexandre Matinin, Victor Samyguin, Inna Filippova

"Comparison of flotation efficiency of the new multi-zone flotation cell (MZFC) and different conventional cells was carried out at lab and pilot scales on the various samples: high contrast pyrite tailings and old copper containing tailings. MZFC is a cell of intensive flotation, which provides optimal hydrodynamic conditions for all flotation sub processes. Enhancing of particle attachment, creation of conditions for coalescent flotation, selection of spatially separated zones according to optimal hydrodynamic conditions for flotation sub-processes are proposed as main principles to design an MZFC. The bubbles/pulp stratification was pointed out as a limiting step in the existing intensive flotation machines. Two strategies to improve bubbles/pulp stratification in the MZFC were studied: (a) impact of pulp-bubble jet to the surface of a prismatic insert inside of cell, which provides the detachment of low hydrophobic particles from bubbles, and (b) profiling the pulp/bubbles jet from the reactors due to a specific geometry of cell walls. The new continuous MZFC devices were demonstrated similar or higher efficiency in comparison with laboratory batch flotation cells for pyrite flotation. Higher flotation efficiency (82%) with pure pyrite concentrate (51.2% of sulfur) and a recovery level of 92% was obtained in MZFC when the cell with stratification by impact was used. Similar results were obtained with old Cu-containing tailings. Although MZFC had 1.5 times greater yields of concentrate than a batch flotation cell, it provided the increase of chalcopyrite recovery by 29.4% and concentrate grade by 4.8%. An original organization of pulp/bubbles stratification in the separator part of the new intensive flotation machine using variable geometry inserts allowed the best flotation selectivity with a bubble mineral loading coefficient 1.5 fold higher than the laboratory mechanical or pilot cells."

Jan 1, 2014

By Lina Chica, Arturo Barrientos, O. Bustamante

Hydrocyclone is a device commonly used in mineral processing industry. Underflow control plays a fundamental role in hydrocyclone operation. This affirmation supports the fact that hydrocyclone underflow has effect in some aspects of separation performance like capacity, split ratio, cut size and bypass. Hydrocyclone operation state is associated to underflow characteristics: air core formation and discharge shape. Many studies attempt to understand size separation phenomenon and the discharge influence but none of them has taken an energy point of view. This work presents the results of a mechanical energy dissipation for hydrocyclone operation from a mechanical energy balance. The experimental results related to Newtonian suspensions show that underflow energy dissipation does not control the operation because this magnitude is small compared to interior energy dissipation. However, discharge energy dissipation provides enough information to describe underflow conditions and its influence in separation conditions. In the modelling non dimensional parameters have been considered for hydrodynamic description and for geometrical and operation hydrocyclone characteristics. Energy dissipation from the continua media approximation results into a relevant concept to understand the hydrocyclone performance and improve industrial installations.

Jan 1, 2014

By F. Karakas

In this investigation, one of the most energy consuming stage of the cement manufacturing process, grinding stage, was studied. The aim of the study is to reduce the energy consumption. Optimum operating parameters were determined. Experimental studies were performed at three differ-ent stages. Grinding of limestone, clay and marl which are the main components of the cement, to approximately below 90 microns, was the first stage of the cement grinding. At this stage, effect of feed size and ball charge were investigated. At the second stage, the Bond work index of clinker and additives (slag, trass, limestone and gypsum) was found separately. After forming composite cement with clinker and additives, the Bond work index of this mixture was also determined, thus the results of separate grinding and grinding of mixture were compared. The Bond work index of mixture was found as 13.59 kWh/t, while the arithmetic mean of the Bond work index values of components was 14.90 kWh/t. Finally, clinker and additives (slag, trass, limestone and gypsum) were ground under the same conditions. At this stage, laboratory type of ball mill was used in order to understand grinding characteristics of the cement components. As a result of the experiments, it was found that energy consumption for the grinding will be lowered if the mills with 38 % ~ 40 % ball charge are used in the cement grinding. Moreover, grinding with mixture of clinker and additives gave better results than separate grinding of these components in terms of energy consumption.

Jan 1, 2014

By Agnieszka Surowiak, Tomasz Niedoba

The paper presents a way of determining relations between ash content in coal, particle size and particle density by means of regression, multidimensional Morgenstern distribution functions and kernel approximation. The three-dimensional random vector (D, ?, ?), where D is a random variable describing particle size, ? - random variable describing particle density and ? - random variable describing ash content, where function ?=?(d, ?) is obtained by means of regressive function. The multidimensional Morgenstern distribution functions and kernel estimators with the use of Gauss function were applied to approximate the functions f(d, ?, ?) and f1(d, ?). This approach is a new way of multidimensional description of grained materials such as coal and it also allows to evaluate material features more properly than the classical statistical approach. The results were verified statistically.

Jan 1, 2014

By X. P. Guo

In this paper the test results of flotation of the kyanite ore from a Chinese mine are described. The objective of this work is to determine effective recovery process to obtain kyanite concentrate with high quality and high recovery for a new concentrator design. The valuable minerals of the ore are kyanite, garnet and magnetite, contents of them are 14.0%, 5.9% and 1.2%, respectively. The gangue minerals are mainly biotite, feldspar and quartz, contents of them are 33.8%, 17.8% and 25.6%, respectively. The kyanite in the ore contains a little iron. In laboratory flotation tests the factors affecting the flotation such as slime, alkalinity of pulp, and flowsheet configuration are studied. The interference of biotite on kyanite flotation as well as selective flotation of garnet is examined. On the basis of above-mentioned results the flowsheet of ore treatment comprising de-sliming, mica flotation, low intensity magnetic separation of magnetite, high intensity magnetic separation of garnet and coarse biotite as well as flotation of kyanite is pre-sented for comprehensive recovery of kyanite, garnet and magnetite. The kyanite concentrate con-taining more than 59% Al2O3 is obtained with a kyanite recovery of 70.0%. The contents of Fe2O3and biotite in kyanite concentrate decreased from 2.02% and 5% to 1.30% and 1%, respectively. The disadvantage of low kyanite grade in raw ore is compensated by accessory recovery of garnet and magnetite in the ore.

Jan 1, 2014

By Paul W. Cleary

"DEM application in mineral processing has for many years been heavily focused on simulating mills of various types. This method can be used to simulate many other aspects of mineral processing operations and can be used both to enhance understanding of the underlying flows and of issues such a breakage, wear, blockage, product degradation, segregation and mixing. The application of DEM to four important classes of non-comminution problems and equipment commonly found in or near mineral processing plants are described. These are:- Particle transport (examples include a conveyor belt and an inclined screw conveyor)- Sampling (assessment of sample bias for cross-stream samplers)- Separation (the efficiency of vibrating screens)- Storage and reclaim (discharge from a multi-port hopper and segregation in a splitter bin with asymmetric ingoing and outgoing conveyor belts, apron feeders and impact plate)."

Jan 1, 2003

Domestic production of pyrite cinder reached 15.95 million tons in 2006. The pyrite cinder used in cement industry accounts for about 30% production. The remaining 70%, 11.17 million tons, was thrown away as waste, which brought serious environmental and resource problems. A new technology of composite pellet reduction-roasting and magnetic-separation (CPRM) has been developed to utilize pyrite cinder. Pyrite cinder sample, containing 45.56% Fe, 0.19% Cu and 1.45% S, was pelletized with addition of 5% composite agent in balling disc. Green balls after drying were reduced at 700~800 ? for 20min with 300kg/t pulverized coal injection in rotary kiln. After two stages of ball-grinding and four stages of magnetic separation, high grade magnetite concentrate with 66.23% Fe was produced, meanwhile impurities Cu and S was decreased to 0.048% and 0.053%, respectively. And iron recovery of 73.32%, desulphurization of 96.34% and decoppering degree of 74.73% were achieved. Key technique is that composite agent can accelerate reduction of Fe2O3 and transfer copper and sulphur into water-soluble inorganic salts, which can be removed during wet magnetic concentration. This new technology can be used to fully utilize pyrite cinder and produce high quality magnetite concentrates as feed for steel industry, which will help tackle the pollution problem of pyrite cinder and extend iron-bearing raw material sourcing for Chinese steel industry.

Jan 1, 2014

By Andrzej Luszczkiewicz, Aleksandra Potulska

"Flotation is a basic process of beneficiation of mineral raw materials which requires very fine grinding for liberation of valuable minerals. Probably flotation will also play this role in the future. In the case of flotation of difficult-to-upgrade non-ferrous ores, currently one of the most important trends in technology development is solution to fine grinding even down to a few micrometers in size and elaboration of effective flotation technology for such fine particles. Both industrial flotation data and many investigators suggest that the best results of flotation of ore minerals are observed for particle size range from 20 to 100 µm. Many base metal ores require grinding below 20, or even 10 µm, to liberate valuable ore components. However, industrial flotation of particles below 20 µm in size creates numerous challenges. Further complications may be caused by a complex nature of the ore, especially when the valuable metals are present in several different sulfide minerals. This problem occurs in the case of the Polish sedimentary copper ores. In the present study, flotation of the ore of different size distributions and degrees of grinding, having the size of particles below 25 µm, was investigated. The behavior of different sulfide minerals naturally present in the ore was analyzed. The best results of flotation tests were obtained for the ore ground down to 95% below 25 µm. Narrow size fractions -10; 10-15; 15-25; 25-40, and +40 µm were separated using special micro-sieves and mineralogical as well as chemical analyses of each size fraction were carried out for monitoring the behavior of the fine sulfide particles. Differences between flotation of chalcocite-digenite, bornite, chalcopyrite, covellite, galena and pyrite-marcasite naturally occurring in the ore were described. The role of different particle sizes in flotation performance of each mineral was also presented."

Jan 1, 2014

By Alireza Javadi Nooshabadi, Kota Hanumantha Rao

Formation of hydrogen peroxide (H2O2), an oxidizing agent stronger than oxygen, by sulphide minerals during grinding was examined. It was found that pyrite (FeS2), chalcopyrite (CuFeS2), sphalerite ((Zn, Fe) S), and galena (PbS) generated H2O2 in pulp liquid during wet grinding and also when the freshly ground solids are placed in water immediately after dry grinding. Pyrite produced more H2O2 than other minerals and the order of H2O2 production by the minerals was found to be pyrite > chalcopyrite > sphalerite > galena. The pH of the water influenced the extent of hydrogen peroxide formation with greater amounts of H2O2 produced at highly acidic pH. Furthermore, the effect of mixed sulphide minerals, i.e., pyrite-chalcopyrite, pyrite-galena, chalcopyrite-galena and sphalerite-pyrite, sphalerite-chalcopyrite and sphalerite-galena on the formation of H2O2 showed increasing H2O2 formation with increasing pyrite fraction. There is clear correlation of the amount of H2O2 production with the rest potential of the sulphide minerals; the greater the rest potential of a mineral the greater the formation of H2O2. This study highlights the necessity of revisiting the electrochemical and/or galvanic interactions between sulphide minerals, and interaction mechanisms between pyrite and other sulphide minerals in terms of their flotation behavior in the context of inevitable H2O2 existence in the pulp liquid.

Jan 1, 2014

By M. Holuszko, I. Mikhalev

"Previous studies described by Galvin et al. (2017) have shown that for Australian bituminous coal fines, both in batch and in continuous process, the new improved oil agglomeration procedure based on the use of high-internal-phase (HIP) emulsions, as compared to the conventional “pure oil” agglomeration process, enables a significant reduction in the amount of oil while reaching a high yield of clean coal (approximately 90% of agglomerates greater than 355 µm in size) in a significantly shorter time. The HIP emulsion used in these experiments comprised up to 95% vol. aqueous solution of sodium chloride (3% wt. concentration) and for the rest, a mixture of kerosene (oil) and sorbitan monooleate (SMO emulsifier) in a 1:1 ratio as a binder. This study evaluates the applicability of the new HIP-oil agglomeration process to treat Canadian bituminous ultra-fine coal and Russian sub-bituminous coal fines and compares results from agglomeration to the flotation response of both coals. Oil agglomeration is known to be sensitive to surface properties of coal. Since surface properties of coals depend not only on the rank of coal but also on their origin (depositional environment) and mineralogical composition, both the applicability of this new improved agglomeration process to the non-Australian coals and its efficiency became the motivation for this study. To evaluate the applicability of the new process to both Canadian bituminous and Russian sub-bituminous coals, a series of bench-scale tests were carried out under conditions similar to those described by van Netten et al. (2016) for the Australian coals. Based on the results obtained in this research, new boundary conditions for the application of the HIP emulsion-based oil agglomeration process have been outlined and conclusions on the viability of the new process to treat ultra-fine coal from Western Canada and Russian sub-bituminous coal fines have been reached.INTRODUCTION In most cases, to meet the market requirements, the mined coal has to be processed to reduce the ash content by the removal of mineral matter and thus to increase the quality of the coal products (van Netten et al., 2016). Generally, flotation is used for processing fines from high rank coals; however, there are high losses of very fine coal due to the inefficiency of this process. Furthermore, difficulty in dewatering the fine coal results in excessive moisture levels causing coal handleability issues, which increases costs in the coal-cleaning industry (Capes & Darcovich, 1984). Much of the development that has occurred in fine coal cleaning has taken place with higher-value coal, often metallurgical (Klima et al., 2012). If the fine coal is deemed to be too difficult or expensive to process, it may be discarded as waste (van Netten et al, 2014). Such disposal not only creates an environmental liability but may also result in the loss of a valuable, high quality product that is better liberated than the coarser fractions of coal."

Jan 1, 2018

In flotation, particulate materials are separated by controlling the hydrophobicity of the particles using appropriate collectors. In this regard, contact angle (?) is the most important process variable. However, the flotation models used in industry today do not include ? as a parameter. As result, flotation circuits are designed based on the first-order flotation rate constants (k) determined from laboratory experiments. A problem with this approach is that laboratory experiments usually give substantially higher k values than achievable in full-scale operations, which makes it difficult to use the model for plant design. In the present work, we have developed a model from first principles using both surface chemistry and hydrodynamic parameters, such as ?, ?-potentials, surface tension (?), particle size, energy dissipation rate, etc. The basic approach is similar to the one developed previously for bubble-particle interactions under laminar flow conditions (Yoon and Mao, J. Colloid and Interface Science, 181, 61, 1996) except that the model parameters have been modified by considering the turbulence in a flotation cell. In addition, the model describes the recovery processes in froth phase, including bubble-coarsening due to coalescence. Based on this model, we have developed a computer simulator (FlotSim) that can be used to design flotation circuits from the mineralogical (or liberation) data on the feed and the hydrodynamic characteristics of a flotation machine. Since the model is dynamic, it can also be used for process control. Further, the simulator has predictive capacity as it is based on a first-principles model. The model-based simulator has been validated in a carefully controlled bench-scale flotation experiments. Keywords: flotation kinetics, flotation model, contact angle,?-potential, size-by-size recovery, liberation, DLVO theory

Sep 1, 2012

By Wenqing Qin, Yunfan Wang, Ximei Luo, Fen Jiao

In order to investigate the effect of nanobubbles on adsorption of surfactant on mineral surface, the nanobubbles on the surface of calcite with -37µm fraction in the sodium oleate system were controlled by pressurization and decompression to mixing vessel. Subsequently, the adsorption amount of sodium oleate on the surface of calcite were detected by ultraviolet spectrum at different stirring times and different pressures. At the same time, the nanobubbles on the calcite surface were imaged with atomic force microscopy (AFM). In addition, a homemade vacuum Hallimond tube device was used for the flotation of single mineral, and the grade and recovery of minerals in concentrate was used to determine the influence of the nanobubbles on flotation. The experimental results showed that a large number of nanobubbles were found on the calcite surface by AFM under the dissolved oxygen difference (DOD) condition of -4 mg/L. And a large difference in adsorption capacity of sodium oleate on the surface of calcite was observed under different air pressure conditions. It indicated that the ambient pressure had a certain effect on the adsorption of sodium oleate on the calcite surface, and this effect did not depend on the constant low pressure or constant normal pressure, but depended on the changing process of pressure. The single mineral flotation experiment results indicated the recovery of calcite under decompression condition (formation condition of nanobubbles) was 1.5-2 times that under constant normal pressure, and the flotation time is much shorter. Moreover, the recovery under constant normal pressure was greatly influenced by flotation time. In this paper, only one aspect of the effect of nanobubbles on mineral flotation was preliminarily explored. It was confirmed that after vacuum-pumping, the adsorption of sodium oleate on calcite surface could be increased, the flotation time also was greatly reduced and the recovery of calcite was increased.

Jan 1, 2018

By Robin J. Batterham

The Bologna Process started in 1999 with a declaration signed by ministers from most European countries. As of 2012, the Bologna Process now has 47 participating countries (EHEA 2012). Overall, the Bologna process has demonstrably changed higher education in many countries to allow for considerably more flexibility in course offerings. Keywords: bologna model, education

Sep 1, 2012

By R. J. Batterham

The science and practice of mineral processing has been driven for many years by the same set of challenges that shape the mining industry ? demand and supply, grades and their decline with time, mineralogy and the need to handle more complex ores, disposal and minimising of wastes and the availability of water, power, skilled labour and the like together with increasing expectations from the community, concerns on sustainability and safety and, as well, climate change forcing a more targeted approach on energy. In this paper, the author builds on previous reviews to the IMPC and suggests that while step changes are long overdue, the unprecedented demand mitigates against drastic changes. That said, the ?Mine of the Future? is already requiring some different approaches.

Jan 1, 2014

By Yuhua Wang, Huilan Yang, Yanqing Jiang, Dongfang Lu

"Generally, the concentration of bauxite flotation tailings is around 10%, a large amount of water in tailings needed to be recycled in the flotation process. Sedimentation and dewatering properties of tailings were investigated under different conditions. Surface high negative charges on mineral particles are the key factor to destroy the settlement of tailings when the pulp pH is around 8.9. Hence, the modification of pulp pH around 7 is necessary to the diminution of the repulsive force between mineral particles and then the acceleration of sedimentation of tailings. Anionic polyacrylamine with molecular weight of 14 million is the best flocculant for the settlement of tailings in all tested polyacrylamines. P-toluene sulfonic acid shows better properties than hydrochloric acid for pulp pH adjustment when anionic polyacrylamine with molecular weight of 14 million is used as flocculant. Although the flotation of diaspore is depressed in the presence of polyacrylamine using sodium oleate as collector, but the recycling water traded by the combination of ployacrylamine and p-touenesulfonic acid does not show the depression effects on the flotation of bauxite ore. The lower residual content of polyacrylamine in recycling water treated by the combination of ployacrylamine and p-touene sulfonic acid plays an important role. INTRODUCTION Generally, the waste water generated from mineral processing plant is usually treated by sedimentation, oxidization, electrodialysis, ions exchange, active carbon adsorption and flotation technology, and the treated water is also used again in the industrial process. Flotation was adopted widely to improve the quality of bauxite from low grade diasporic bauxite in China. For flotation, the grinding fineness of bauxite is over 90% -0.074 mm, sodium carbonate and sodium hexametaphosphate were used as regulators, so the tailings pulp is very difficult to settle and be dewatered (Y. Wang et al., 2004; Y. H. Wang et al., 2007; Wang Yu-hua et al., 2008; Wang Yuhua et al., 2011). The water recycling of bauxite tailings are becoming the highlight for the industrial application of the flotation process for bauxite ore. Researchers in China shift their attentions onto this topic."

Jan 1, 2018

By Sumantra Bhattacharya

The per capita energy consumption in India is 510kgoe/year, the global average being nearly 1818kgoe/year. Correspondingly low is the per capita CO2 emission at 1.25t against the world average of 4.39t.65-70%, at times more, of India?s power generation from about 190,000 MW installed capacity, is however coal fired.India therefore has to secure diversified sources of energy and solar power is increasingly being looked as the real alternative to the existing over dependence on coal. To ensure sustainable solar power it is essential to secure its raw material base that is ?silica?, hitherto considered as ?minor minerals?. That calls for immediately addressing the issues of land availability, solar power cost, developing a dynamic inventory of silica containing minerals, appropriate processing technology and strong regulatory framework for sustainable mining and processing of all silica rich minerals. Keywords: silica, silicon, Thar, power generation, India, quartz, solar power

Sep 1, 2012

By J. B. Rubinstein

"The paper gives an overview of the history of flotation machine development. The laws of their evolution are stated and the place and role of column flotation are demonstrated.The major parameters of column cell diameter and height are discussed. Options are proposed for optimization of the hydrodynamic characteristics of large-capacity column cells. The high efficiency of columns with cell height of 4-6 m is demonstrated. The optimum parameters of multisectional column machines are determined. Their advantages compared to monocells are shown. A scaling-up procedure for column machines was developed based on flotation macro- and microhydrodynamics simulation."

Jan 1, 2003

By Xuliang Yang, Yuemin Zhao, Bo Zhang, Liang Dong, Cheng Sheng, Gongmin Li, Zhenfu Luo, Yaqun He, Chenlong Duan

Coal plays an important role in the primary energy consumption of all over the world. In 2012, coal reached the highest share (29.9%) of global primary energy consumption since 1970. Coal burning mainly contributes to the emission of SO2, NOX, Hg and other impurities that jeopardize the future of environment. . Beneficiation before coal utilization is the most economical and effective technology for removing the hazardous material and gangue. In this paper, a novel process of dry beneficiation based on gas-solid two-phase flow composed of the compound dry cleaning separator (FGX), the air dense medium fluidized bed separator (ADMFB) and the vibrated fluidized bed with autogenous medium (VFB) is proposed. The main equipment and the flowsheet of the united system are described in detail. Separating principle of the FGX, ADMFB and VFB devices are all based on gas-solid two-phase flow. In FGX, gassolid suspension is composed of continuous gas flow and coal powder in feed coal. Large size coal (+6- 80mm) can be pre-separated effectively, and large size gangue can be removed effectively. Moreover, - 6mm particles fed serve as autogenous medium in FGX. The probable E value is 0.13 for -80 mm raw coal. In ADMFB, magnetic powder with -0.3 + 0.045 mm size fraction and coal powder in feed coal are compound medium solids. The separation density can be adjusted and controlled according to properties of raw coal. -50 + 6 mm raw coal can be cleaned efficiently, the probable E value is 0.05. In VFB, -6 + 1 mm coal can be separated. Generally, -80 mm raw coal can be cleaned efficiently in the united system based on gas-solid two-phase flow.

Jan 1, 2014