Search Documents

By Rodolfo Silva, Antonio Peres, Afonso Martins, Gilberto Ramalho, Mario Cabello

The consumption of aggregates in civil construction has increased considerably in Brazil for the last years. The extraction of sand and gravel generates significant environmental impacts. As the quarries and sand deposits are getting exhausted near the big cities, the price of aggregates is increasing. Meanwhile, the extraction of quartzite (dimensional stone) in the state of Minas Gerais has been done mostly in small quarries, with very low recovery, generating approximately six million tons of wastes a year, which causes pollution, increases final prices of products, decreases the life time of quarries and ends up in the closure of enterprises. The government agencies and the quarries’ owners understand that only by finding applications to wastes there will be development to the sector. The aim of this investigation was to study the application to the quartzite wastes as aggregate in the civil construction. Samples of quartzite wastes collected in a quarry were characterized by petrographic analyses. Laboratory tests of crushing and grinding were done to analyze the viability of reducing the size of coarse material to a finer one to be used as raw material in industrialized mortars and concrete pre-molded components.

Jan 1, 2014

By A. Gueciouer, A. Akkouche, K. Chalah, A. Benmounah

"Drilling solid waste is a typical industrial solid waste, and it is a major pollutant source to ecological environment. Generally, waste management dewatering systems separate solids and fine particles from the liquid phase of drilling fluid, thereby leaving a clarified aqueous solution and allow the cleaning of waste fluids. Typically, dewatering waste management systems clean drilling fluid through coagulation, flocculation and/or mechanical separation. Chemicals used in dewatering are based on the coagulation-flocculation process, which it facilitate the removal of suspended solids and colloidal particles. The factors which can promote the coagulation-flocculation are velocity gradient, contact time, and PH. The objective of this work is to optimize a formulation adequate for dewatering based on the coagulation-flocculation process used coagulant (Aluminum sulphate), anionic flocculants (Partially Hydrolyzed Polyacrylamide) and anionic polyelectrolytes (in solid form with linear chain with very high molecular weight). The results obtained show the good efficiency of the coagulant and flocculants. INTRODUCTION Rig site dewatering of drilling fluids with recycling of processed water can help an operator to comply with environmental rules by reducing volumes of waste and reducing long term liabilities. It can also reduce disposal costs and provide a cleaner drill site overall. Most of the environmental concerns during the 1980s involved hazardous materials and toxic wastes. Drilling fluids, many of which are chemically benign, have escaped many of the difficult-to-comply-with rules and regulations. During the 1990s, however, operators may be required to submit a written plan for liquid waste reduction for even nonhazardous materials. Many states and local agencies may institute total bans on oil field wastes. Drilling rigs typically produce about 1 bbl of liquid waste for every 1 ft of hole drilled. Thus, a typical drilling operation can produce a large quantity of waste [1]. To improve the dewaterability of sludge, different pretreatment processes have been widely studied and developed including thermal, chemical, magnetic, mechanical, acoustic, electric, electro-acoustic and their hybrid treatment processes [2]. Rig site dewatering (figure 1) is the process of injecting coagulants or flocculating chemicals into the mud entering a large clarifying centrifuge. Coagulation occurs when the solid and allowing it to be attracted to other solids by van der waals forces. Flocculation is the binding of individual solid particles into aggregates of multiple particles. It is physical, rather than electrical, and occurs when one segment of a flocculating polymer chain absorbs simultaneously onto more than one particle [3]."

Jan 1, 2018

By Junji Shibata

In a present process to treat the tungsten carbide tool waste, the wastes are roasted in air and then an alkali leaching is carried out in an autoclave. An environmentally friendly process is required to recover rare metals (Co and W) from the wastes. The effect of mechano-chemical (MC) treatment on leaching of rare metals was investigated in this study. The solvent extraction and crystallization-stripping methods were applied to separate and recover tungsten and cobalt in the leached solutions. The MC treatment for the rare metal leaching is effective to dissolve rare metals from the wastes due to the change in crystalline structure of WC and oxidation of WC with KMnO4. Cobalt ions are extracted with D2EHPA by a cation exchange reaction. Tungsten in the leachate can be extracted by TOA (tri-octyl amine) as an extractant, because tungsten species exist as a form of anionic species in acidic solution. The rare metals in organic phase are recovered as insoluble salts such as oxalates and ammonium salts in the crystallization-stripping process. Keywords:unheated oxidation, solvent extraction, crystallization-stripping, recycling

Sep 1, 2012

By P. Somasundaran

Treatment of mineral surfaces with appropriate surfactants plays an important role in mineral processing operations such as flotation, flocculation and dewatering. Recently biosurfactants, in particular, have received a considerable amount of attention because of their unique surface active properties and biodegradability. In this work we examined the performance of biosurfactants, sugar based alkyl glycosides and sophorolipid esters as reagents to control the hydrophobicity of minerals with selectivity of adsorption on mineral surfaces for flotation applications. It was discovered that n-dodecyl-ß-D-maltoside adsorbs on alumina, titania and hematite but, interestingly, not on silica. The hydrophobicity obtained is governed both by the surface coverage as well as the nanostructure of the adsorbed layer in terms of orientation of the adsorbed species. Surprisingly, even though the above surfactants are non-ionic, their adsorption was pH-dependent. We have correlated this pH dependence to the type of species on the mineral surface. Also it is shown that mixing of these surfactants with traditional ones can help reduce the carbon footprint due to synergy between the reagents and help selectivity due to antagonism. The experimental results were analyzed to get information on optimal pH and dosage conditions, for mineral surface modification. The study provides guidance for mineral treatments using biosurfactants and the potential use of these next generation reagents in mineral processing.

Jan 1, 2014

The characteristics of mineral resources and tailings resources in China are analyzed. Those tailings, which have double characteristics, can occupy land, pollute environment and even influence human habitat if they are not disposed in time. So pay attention to the comprehensive utilization of the tailing more and more both at home and abroad. The present situation and problems in comprehensive utilization of iron tailings in China are introduced by combine some practice experience, and have looked forward to the comprehensive utilization of iron tailing situation.

Jan 1, 2014

This paper discusses current workforce demand projections for mineral processing engineers and emerging trends in mineral processing education. Attempts are made to identify gaps that often result in a mismatch between skills taught and skills needed by the practicing engineer. Clear examples of this include a less than uniform training in chemical aspects of mineral processing, and an understanding of the statistical and experimental design tools necessary to tame the often-large variation in operational parameters and plant data. The end goal is an educational system modernized to prepare mineral processing specialists for productive careers in the sustainable development of natural resources. A framework for revamping education based on an integrated modular approach is also presented. Keywords: mineral education trends, mineral processing programs

Sep 1, 2012

By Z. Q. Zhang

The iron ore from Yichang in China assaying 41.64% Fe and 1.02% P is a low grade and high phosphorus oolitic hematite ore. The separation of iron minerals from gangue minerals in the ore by conventional processing techniques is ineffective owing to their close similar properties. The modification of iron minerals by microwave-assisted reduction was investigated in order to improve separability of the ore. The effects of microwave-assisted reduction on the subsequent low intensity magnetic separation and floatation were examined. The results show that the main factors affecting the reduction and separation process are grinding size, reduction temperature and reductant. Fine grinding of the microwave-treated ore to smaller than 0.074mm was found to be imperative due to the tiny dissemination characteristics of iron oxide minerals. After magnetizing reduction by microwave heating at 500?, the magnetic concentrate containing 58.36% Fe and 0.67% P can be obtained with the Fe recovery of 91.28%. Magnetizing reduction drops the floatability of iron oxide minerals, thus reverse flotation is fit for upgrading the magnetic concentrate to contain 62.13% Fe and 0.21% P with Fe recovery of 81.59%. Compared with present microwave-assisted reduction technique of carbon reductant, using a waste iron powder as reductant is a novel and effective technique without the green house effect caused by the release of CO and CO2. Waste iron powder with a faster response to microwave heating then coke and charcoal can be recovered by magnetic separation in a low cost and plays the role of reductant and microwave heating accelerator.

Jan 1, 2014

By Q. X. Li

The state discharge standard for arsenic-containing wastewater which is the first kind of pollution is less than 0.5 mg/L. In fact, in a certain company, the acidic arsenic-containing wastewater in non-ferrous smelting was as high as 860 mg/L, which is far beyond the state discharge standard. Obviously, the direct release of this wastewater without further treatment would result in great hazards to the ecological environment. To aim directly at the characteristics of acidic arsenic-containing wastewater, in this study, two steps of treatment including oxidation-flocculation and removal fluoride by mixing alkaline neutralization were suggested. Through analyzing various influencing factors in treatment effects, the optimum technical conditions were obtained. The sediments after treating were recyclable and the secondary pollutions can be avoided. Moreover, the results also show that, all indexes of the effluent after treating are lower than the First Grade Standard of Integrated Wastewater Discharge (GB 8978-1996). This novel method has advantages of short flow sheet, easy operation and low cost.

Jan 1, 2014

By P. V. Ramesh Babu

India has sizeable number of small deposits of rare metal bearing minerals namely columbite-tantalite, pyrochlore, beryl, lepidolite, spodumene and rare-earth element bearing minerals monazite and xenotime in different parts of India. Pegmatites, alkali granites, syenites, and the derived gravel and soils are the main source for rare metal and rare earth (RMRE) minerals. The RMRE minerals are classified as prescribed substances under Atomic Energy act of 1962 keeping in view the uses in the nuclear industry. Atomic Minerals Directorate for Exploration and Research (AMD) of Department of Atomic Energy (DAE) is the sole agency responsible for exploration and exploitation of RMRE minerals in India since 1962. The latest technological advancements and applications in the field of space, electronics, communication and nuclear industry using these metals and their products have necessitated to augment the production and resources of RMRE minerals. These minerals play a significant role in the technological and economic development of the country. The light rare earth element bearing mineral monazite is abundant in beach sands and is being commercially exploited by Indian Rare Earths Limited (IREL). Columbite-tantalite, the chief source for niobium and tantalum (Nb-Ta) metals present in the pegmatitic gravel are recovered by small mobile beneficiation plants. The cut and fill method of mining adapted is eco-friendly. The processing flow-sheet consists of wet sizing at ½ in and 1mm followed by gravity concentration of sized products utilizing the methods of jigging and wet tabling. The sizing equipment include revolving and vibratory screens and the gravity concentration equipments used are fixed sieve jigs and movable screen jigs for final upgradation. The gravity concentrates are further upgraded by magnetic separation to remove magnetite and ilmenite. The mine areas are reclaimed by filling with coarse size tailings and new plantations. These mobile pilot plants were earlier operated in Bihar mica belt, Jharkhand, pegmatitic areas of Karnataka and Nellore mica belt of Andhra Pradesh and are currently being operated in Bastar-Malkangiri pegmatite belt of Chhattisgarh and pegmatites of Jharsuguda district of Orissa. Beryl, lepidolite, spodumene and cassiterite minerals are the by-products from the pegmatite ores. Fergusonite, samarskite and microlite are the other niobium and tantalum bearing minerals which are also found in pegmatites. Xenotime, the chief mineral of yttirium generally occurs in granites and pegmatites. The rare earth minerals monazite and xenotime get concentrated in the placer sands of rivers and beaches. The occurrence of xenotime in the sands of Siri River and Deo River in Chhotanagpur granitic terrain in parts of Chhattisgarh and Jharkhand are an example. These sands containing 1-2.5% heavy minerals were processed by a mobile plant consisting of sizing equipments like trommel and vibratory screen followed by separation of heavy minerals from -1mm sands with the help of gravity concentration equipments like spirals/shaking tables/sluices. Xenotime and monazite from the pre-concentrate are further separated by magnetic and electro-static methods. The present paper illustrates the pilot plant set up for the recovery of rare metal as well as rare earth minerals. Keywords: small deposits, rare earths, rare metals, pegmatite, Nb-Ta, xenotime, India

Sep 1, 2012

Producing robust agglomerates with desirable structural properties is the key to success of the heap leaching of complex, low-grade nickel laterite ores. Mechanically strong but porous agglomerates with narrow size distribution (e.g., 5 ? 40 mm) are required to build permeable and perennially stable heaps of 4 ? 10 m height. The characterization of granules? microstructure is essential for greater understanding and correlation with the concomitant mechanical properties and robustness. In this study, we used non-destructive, computed X-Ray tomography analyses and scanning electron microscopy (SEM) in tandem with conventional compressive strength,and integrity/stability tests to draw links between nickel (Ni) laterite agglomerate strength/stability, internal microstructure (e.g.,porosity, inter-particle bridges) and binder type. It is shown that binder composition (e.g., tap water vs. 30% w/w H2SO4) and post-agglomeration drying both significantly impact on granules? physicochemical and microstructural properties. Acidic binder, in contrast with tap water, leads to significant incongruent leaching of different species from particles during ore-binder mixing and agglomeration. Upon wet agglomerate curing, solidified/recrystallized leached species form strong intra-granular solid bridges which, lead to greater compressive strength of dry agglomerates. Structural stability/integrity of cured agglomerates in acidic solution, however, decreases dramatically due to greater porosity and acid solubility of intra-granular solid bridges. These findings are useful in shedding more light on agglomerate structure characteristics and their optimization for enhanced column and heap leaching with concentrated sulphuric acid.

Sep 1, 2012

By V. Sheikhzadeh, M. Saghaeian, R. Hejazi, A. Abazarpoor

"The morphology of pellet feed is known to influence several properties of iron ore pellets, including drop number, compression strength and reduction properties. The effect of grinding method on the particle size, specific surface area and particle shape of an iron ore concentrate has been studied. Grinding methods considered were ball mill and high pressure grinding rolls (HPGR). 5 different samples (Blaine= 1800, 1900, 2000, 2100 and 2200 cm2g-1) were used to compare the size, shape and specific surface of particles for each grinding methods. Particle size was meticulously examined by sieve analysis, laser sizing and image analysis. In samples ground by ball mill, it has been observed that the fraction of particles <10µm increases from 39% to 46% as the Blaine number increases from 1800 to 2200 cm2g-1. For HPGR samples, corresponding figures are 41% and 49% respectively. It is evident that for samples ground by HPGR, the fraction of fine particles is higher than that of those ground in the ball mill. To measure the specific surface area of particles, Blaine and BET were used. A higher real surface area was observed from HPGR treatment in comparison to ball mill grinding, provided by a higher porosity, cracks, roughness and new surfaces. Shape factor of particles was determined using three descriptors: circularity, roughness, and aspect ratio. It was also observed that particles produced by HPGR were more elongated, less circular, and rougher than those processed by the ball mill. 1. INTRODUCTION Particle size and shape are important parameters that can significantly affect mineral processing plants and pelletizing plant performances (Brozek and Surowiak, 2007). It has also been proposed that green pellet quality is directly related to the amount of fine particles in a pelletizing plant (Dwarapudi et al., 2008; Umadevi et al., 2008; Gul et al, 2014; Van der Meer, 2015). Particle size distribution and specific surface area (SSA) are also key factors that can control the quality of green and fired pellets. Processing circuits generally reduce the fines fraction to lower than the required specific surface area (SSA). It is therefore necessary to regrind concentrates to produce suitable pellet feed for further treatment in the balling and firing steps [1, 2]. Two main methods are used for re-grinding of concentrate; high pressure grinding rolls (HPGR) and ball mill. Given the different forces used to reduce size in these methods, it is expected the shape of particles will be different (Pourghahramani and Forssberg, 2005)."

Jan 1, 2018

By Peter Kondos

The need for a sustainable development of ore deposits makes it imperative to be innovative and mindful in creating an economically and environmentally viable operation, while maintaining a good working relationship with the various stakeholders involved in developing and operating a large and complex mining project. This is becoming immensely important as gold ore deposits are becoming more mineralogically complex along with lower grades presenting both metallurgical and environmental challenges that need to be addressed in mitigating risks and improving project economics. This paper presents Barrick?s approach to development of strategic technologies for our long-term sustainable growth through conversion of valuable resources into reserves for both our green-field development projects and the expansion of our existing mining operations. Some of the key strategic solutions, including mineral processing, metallurgical and energy technologies, developed by Barrick and their impact on some of our complex gold and copper-gold ores will also be discussed in this paper. Keywords: gold ores, copper-gold ores, processing, breakthrough technologies

Sep 1, 2012

By X. W. Lv

The intelligent recognizing and processing system for sinter ore mineragraphy make a great convenience of recognition and measurement. Specially, it?s critical important for a successful intelligent system to extract the minerals? feature accurately and sufficiently. Reflection index, as the crucial feature of mineral, is calculated by the theoretical calculating model of index based on the principle of imaging color models. In gray histogram of minerals? micrograph, the peaks? positions represent the information about mineral categories and contents. The relationships of different minerals? peak-positions in curve of gray histogram were got by using the peak-find model of gray histogram and calculating model of reflection index. These two models which can be regard as the method of feature extraction for minerals? photomicrograph also lay a good foundation for the artificial intelligent system of recognition and processing in sinter ore.

Jan 1, 2014

By G. V. Kalabin

"The paper supports applicability of satellite imagery at regional and local level for rapid quantitative assessment of natural environment in zones of activity of mining complex enterprises. Exacerbation of environmental problems during mineral mining and processing associated with their scale and geography of field distribution through the vast territory of our country requires constant monitoring of natural environment status, which necessitates engagement of space surveillance nowadays. It is proposed to use the monitoring of land cover and land use at regional and local level for the environmental assessment of a particular production or complex productions. You must establish the dependence of NDVI change trend with the magnitude of anthropogenic impact on the source or multiple sources of environmental pollution a particular area.. We present the results of studies of vegetation remote sensing methods in a number of territories placing mining enterprises. INTRODUCTION Ensuring a healthy environment is necessary both in untouched areas and disturbed. The condition of the developed territories should be monitored with particular attention, since the restoration of the disturbed territories requires great efforts and financial costs. More narrowly, the health of the environment (Zakharov V.M. and etc.,2001) means its quality ensuring the health of man and other species of living organisms, which includes two aspects (Zakharov V.M. and etc, 2000): - ensuring an environment conducive to human health as a biological species: - maintaining the health of the natural environment, i.e. its constituent species of living organisms and plants. The consequence is the disturbance of natural ecosystems, which determines the quality of the environment, favorable for human habitation and the state of health of the population in total determine the status of the territories where enterprises for the development of georesources are located and allow them to be ranked according to the degree of environmental danger. Without knowledge of the trajectory of ecosystem successions, it is impossible to offer adequate requirements for the technologies used to ensure the implementation of the preserved natural potential after the removal or reduction of man-made stress."

Jan 1, 2018

By R. P. Bhagat

The paper reports results on sinterability of iron ores from the mines of Tata Steel Limited. The objective was to improve tumbler index (TI) of sinter and its reduction parameters, reduction degradation index (RDI) and reducibility (RI) while maintaining strand productivity same or to improve. Pot sintering experiments were carried out with Joda and Noamundi mines having LOI 3.8% and 2.9% respectively. Sinter basicity (CaO/SiO2) was varied in the 2.1 to 2.5 range and its MgO content was kept in the 1.4% to 1.8% range according to the blast furnace requirement. The ignition condition and vacuum was maintained according to the plant practice. The effect of variables namely, granulometric composition of ores vis-à-vis that of sinter mix, bed height, solid fuel, moisture content of green mix on the sintering indices was studied. The productivity with Noamundi ore (26 %+6.3 mm) was lower than that with Joda ore (45% +6.3 mm) at 4% coke in the mix and sinter basicity (CaO/SiO2) 2.1. However, with 4% coke (ash 22%) the RDI value was significantly high in case of Noamundi Ore, which decreased significantly to 29% with 5% coke. The size parameter of ore fines and its LOI content do influence the sintering speed and the sinter properties significantly. At 2.1 basicity ratio, the sinter with the Joda ore having coarsergranulometry had highest TI (=70.2%). The RDI (27%) in this case was inferior to that (23.2%) when Joda ores with finer size was sintered. Better RDI with finer sized ore could be attributed to better assimilation of CaO/ MgO with more balanced and uniformly distributed hematite minerals. The size parameter has been inter-influenced by the coke requirement. With the lower mean sized Joda ore the sinter RDI decreased significantly to 23% and the productivity improved to 42.9 T/(sq m*d) when the coke in the mix increased from 4% to 5%. An attempt to reduce the coke in the mix from 5% to 4% with respect to both the ores was not successful as it resulted higher RDI and lower strand productivity. The present study has revealed that sinter RDI improves (decreases) with decrease in the sintering time, while such correlation was absent between TI of sinter and speed of sintering. Corollary to this observation, one can take advantage of other stronger parameters to increase the sintering speed (and hence sinter productivity) without affecting the sinter strength. In the present study higher FeO sinters has displayed excellent RDI, however cold strength of sinter was not correlated with its FeO content. The TI and RI parameters of sinter improves marginally with increase in its MgO content while RDI got worsened. Keywords: LOI content, iron ore, reduction properties, sinter, noamundi, joda

Sep 1, 2012

By M. R. Garmsiri

With the environmental issues and water recycling becoming more significant, the development of deep cone thickeners has improved the efficiency of thickening. While deep cones performance is dependent on many factors, the sensitivity of an industrial thickener to each variable factor has not been determined. In this work, four industrial deep cone thickeners, which are used on tailings stream in Shahrebabak Copper Complex, were monitored for a year to analyze the effectiveness of different factors affecting the performance. Feed flow rate, fine fraction of the feed, solids concentration, flocculant dosage and concentration, solids density, pH, temperature and bed height were the factors investigated on the basis of partial R2 and partial correlation. Results indicated that, with positive effect, feed slurry dilution affected the dewatering efficiency most sensitively. With a negative effect, the sensitivity of dewatering efficiency of deep cone thickeners to flocculant dosage was negligible. While, decreasing flocculant solution concentration had a considerable positive effect.

Sep 1, 2012

By Paul W. Cleary

"DEM application in mineral processing has for many years been heavily focused on simulating mills of various types. This method can be used to simulate many other aspects of mineral processing operations and can be used both to enhance understanding of the underlying flows and of issues such a breakage, wear, blockage, product degradation, segregation and mixing. The application of DEM to four important classes of non-comminution problems and equipment commonly found in or near mineral processing plants are described. These are:- Particle transport (examples include a conveyor belt and an inclined screw conveyor)- Sampling (assessment of sample bias for cross-stream samplers)- Separation (the efficiency of vibrating screens)- Storage and reclaim (discharge from a multi-port hopper and segregation in a splitter bin with asymmetric ingoing and outgoing conveyor belts, apron feeders and impact plate)."

Jan 1, 2003

By F. Q. Cheng

Despite the successful industrial practice to recovery KCl by flotation, the adsorption state of collectors at KCl salt surfaces is still not fully understood. In this paper, the captive bubble contact angle measurements at KCl and NaCl crystal surfaces in their saturated solutions are reported. The influence of different collectors and their concentration are considered. The results show that both cationic and anionic collectors produce a hydrophobic state at the structure breaking KCl salt sur-face, with finite contact angle values of between 30o and 40o. In contrast, the contact angle at the structure making NaCl salt surface is zero at all collector concentrations, suggesting that no collec-tor adsorption occurs, a supposition that is supported by results from molecular dynamics simulation (MDS). Further, it appears that the presence of surface defects such as edges and corners promote the adsorption of collectors at the KCl surface, and that the flotation is achieved by bubble attachment at the edges/corners of KCl particles with the formation of aeroflocs.

Jan 1, 2014

"The research aimed at solving the problem of measuring instantaneous local physical quantities for multiphase flows in mineral processing, which are common in minerals industry and with significant challenges. Due to the lack of proper measurement tools currently in minerals industry, multiphase flows (such as in flotation cell) are treated as in a “black-box”. It is crucial to develop measurement technique by which the acquired processing data can be used for process optimization and control. By measuring the conductivity distribution across a measurement area, Electrical Resistance Tomography (ERT) has been adopted by many researchers to monitor and investigate many processes involving multiphase flows in other industry sectors. A compact ERT probe was built and then used to measure the conductivity distribution within a few flotation machines. In a flowing foam flotation column, the results showed that ERT can accurately measure the change of liquid content (high conductivity fluid distribution). In another part of work, based on the Green-Kubo relations, ERT can measure turbulence via the fluctuation of conductivity caused by bubbles moving through the measurement area, changing the density of the fluid. The tests with the Metso 3 m3 RCS flotation cell were also carried out for turbulence measurement under different air rates and impeller speeds. The results of flotation cell from ERT measurement showed that varying impeller speed had more pronounced influence than changing air rate. When impeller speed is increased, the size of the high turbulent zone increases. ERT is a powerful technique that has the potential to be used for a wider range of applications. The future work will be carried out with more case studies and expanded to more processes such as leaching process, high temperature flows in further downstream production chain (steel making process and alloy manufacturing process).INTRODUCTIONMultiphase flows constitute a majority of the naturally-occurring and industrially-relevant flows, especially in mineral processing. Some of the measurement techniques have been used for the study of fluid characteristics. Optical techniques such as Laser Doppler Anemometry (Kyselaa et al., 2013) and Particle Image Velocimetry (Nobach and Bodenschatz, 2009) can produce accurate measurement results with high spatial and temporal resolution, but their applications are limited to transparent flows. Hot wire probes (Amini et al., 2013) have high spatial and temporal resolution in turbulence quantification, but they are susceptible to environmental factors."

Jan 1, 2018

By J. K. Qu

As one of the key inorganic chemical industries, the chromate chemical industry has spawned extensively public concerns due to the resulted environmental pollution. The cleaner production technology for chromium compounds bases on sub-molten salt medium developed by the Institute of Process Engineering, Chinese Academy of Sciences has greatly decreased the reaction temperature and energy consumption, significantly in-creased the utilization ratio of the chromium element, and successfully achieved the comprehensive utilization of chromite resources and zero emission of chromium-containing residue. The separation process of production is the most important components in the cleaner technology. In this work, we studied two parts: the first is the removal of SiO2, Al3+ from the system and the recycling utilization of alkali metal medium through adding Ca(OH)2 and CaO; the second is to get more pure K2CrO4 crystalloid and remove K2CO3 from KOH solution through evaporation to prepare raw material for manufacturing Cr2O3 and get 50%(wt) KOH. The results obtained show that Ca(OH)2 can remove Al3+ more than CaO and has lower caustic ratio than CaO when they were added 110% of theoretic quantity. The optimal pure K2CrO4(96%) can be gained at 45 Celsius degree in 30% KOH solution and K2CO3 in 50% KOH solution could be decreased to 3.5%(wt) at 40 Celsius degree. And then K2CO3 can be causticized with adding Ca(OH)2 to recycle potassium alkali. The impure material can be re-moved and suitable raw material for manufacturing Cr2O3 can be gotten and reaction medium can be also recycled in this process technology, realizing cleaner production effectively.

Jan 1, 2014