Search Documents

By S. Banisi, A. R. Ghasemi, M. Maleki-Moghaddam

Direct observation of the charge shape and its motion in industrial mills are not possible, it is then customary to use transparent end, small-scale mills (i.e., model mills) to determine the charge trajectory directly by visualization methods. Because of a short length of the model mills, the end-wall effects could introduce a significant bias on the observed charge trajectories and shape. The shorter the mill, the stronger the bias. This could be due to some material bridging between the end walls. In this research, the end-wall effects were investigated by gradually increasing the model mill length and analysing the charge trajectory and shape variation at a given operating conditions (i.e., ball filling, mill speed, liner type). The unbiased mill length was assumed to be beyond the mill length where no significant change observed in the charge trajectory and shape. For all tests, the torque of the charge was also measured by a torque sensor. The special design of the model mill with the diameter of 100 cm made possible to increase the mill length in steps of 3.6 cm up to 21.6 cm. Four types of liners, five steel ball fillings (10, 15, 20, 25, 30% v/v) and three mill speeds (55, 70, 85% of critical speed) were tested. The ball sizes ranged from 4 to 12 mm. The results indicated that when the mill length was below 10.8 cm the end walls prevented the charge from free falling. This resulted in lower impact point angles and lower power draws compared with the case of no end-wall effects. When the same experiments were performed using an iron ore instead of balls with the same size range, the impact of end-wall effects was more pronounced. For an increase of 30% in the speed (from 55 to 85%), the torque due the change in the charge shape decreased by 41% (from 3.7 to 2.2 kgf.m) when mill filling was 30%. At the same operating conditions when steel balls used the torque decreased only by 19% (from 9 to 7.2 kgf.m). This was expected due to irregular shapes of the ore particles which facilitated bridging. Three-dimensional DEM simulations also resulted in the similar conclusions.

Jan 1, 2014

By Xianjun Lyu, Junxiang Wang, Peng Wu, Minjie Lian

"In recent years, the efficient cementation of mine tailings is a new way to manage mine solid wastes. The traditional cement materials have a slow setting time, large dosage and poor cementation strength for fine aggregate such as mine tailings. Therefore, the preparation of new type cementitious materials for the cementation of fine tailings has great potential in the treatment of mine waste solids. The paper mainly focuses on exploring the critical factors affecting the cementing performance of granulated blast furnace slag and its performance in the cementation of fine aggregate. Results indicate that the fineness of slag has a significant effect on its cementitious activity and Portland cement clinker has a better stimulation effect on the cementitious properties of slag than lime. And, anhydrite has a better early stimulation effect on the cementitious properties of alkali-activated slag compared to semi-hydrated gypsum and dihydrate gypsum. According to a series of tests on the cementation of fine iron tailings, the optimal ratio of slag, Portland cement clinker and anhydrite is determined as 60:30:10. Compared with P.O 42.5 ordinary Portland cement, the new slag based cementitious material shows much better cementing performance on fine tailings sample. Under the dosage of 12%, the compressive strength of fine tailings mortar using slag-based cementitious material in 3 curing days is increased to 168% that of using P.O 42.5 ordinary Portland cement, while the compressive strength in 28 days curing period is increased to 194%."

Jan 1, 2018

By Z. Q. He

This paper introduces the structure and working principle of SLon magnetic separator that has excellent performance in iron removal, and summarizes a part of the examples of applications, which applies this machine to remove iron from non-metallic ores, and shows widespread prospect of application of this machine in the purification of non-metallic ores.

Jan 1, 2014

By Brian Hart, Stamen Dimov

"In refractory ores, a substantial part of the gold content may be present as a sub-microscopic component within the mineral matrix of the various carriers. This type of gold may be present as finely disseminated colloidal size gold particles (<0.5µm) or as a solid solution within the sulphide mineral matrix. Such ores are not amenable to gold recovery by direct cyanidation. In order to liberate the sub-microscopic gold, the ore has to be oxidized before being subjected to gold cyanidation and extraction. Autoclave pressure oxidation (AC POX) of the sulphide ore and subsequent cyanidation is a common technology used to liberate the gold in such refractory ores. The additional presence of active carbonaceous matter in such ores (double refractory ores) represents another major obstacle for efficient gold recovery during the process of pressure oxidation and cyanidation. This carbonaceous matter (c-matter) can adversely affect the gold recovery due to its ability to adsorb, or pre-grob gold from the cyanide solution. Advanced micro-beam analytical techniques such as Dynamic Secondary Ion Mass Spectrometry (D-SIMS) and Time-of-Flight Secondary Ion Mass Spectrometry (TOF-SIMS) have become powerful tools for characterization of different forms and carriers of gold for the needs of the mineral processing industry. Major advantages of these techniques are related to their ability to analyze individual mineral particles and provide quantitative analysis with detection limits in the low ppm/ppb concentration range. This paper describes various micro-beam techniques and procedures implemented at Surface Science Western (SSW) for quantification and characterization of the sub-microscopic gold and the preg-robbed surface gold as part of full gold deportment studies in feeds and process stream products."

Jan 1, 2014

By V. Buddhiraju

Liberation of valuable minerals from low-grade ores is an important challenge faced by the minerals industry. It is necessary to grind the ore to extremely fine size in order to liberate the mineral from such ores. As it is generally difficult to produce ultra-fine particles of diameter less than 1-10 mm using traditional grinding equipment such as the ball mill and the rod mill, several new types of grinding equipment are being explored to produce ultra-fine particles. The planetary ball mill is promising in that it makes grinding to submicron sizes possible by imparting high energy to the ground powder. It consists of four pots mounted on a disc. The pots and the disc rotate in opposite directions. The high-speed rotation of the pots and the disc makes the grinding media move at high centrifugal velocities leading to high impact energy and thus improving the grinding performance. The planetary mill is currently being explored for its capability to produce ultra-fine particles on a large scale. In this context, there is a need to understand the dynamics of the ultra-fine grinding process within the planetary ball mill. Here, we address this need by studying the movement of media inside the pots and the grinding kinetics, employing both experimental and modeling techniques. The experiments were conducted on a laboratory scale planetary ball mill. The particle size distribution of the powder was monitored to allow an estimate of the grinding kinetics to be made while video images of the media profiles inside the pots were taken to allow quantification of the media movement as a function of process variables such as the media size, percent loading, etc. The population balance modeling (PBM) framework was used to simulate the kinetics of grinding while the discrete element modeling (DEM) approach was utilized to simulate the media motion. The parameters in the population balance model, namely, the specific breakage rate and the breakage distribution function were determined by fitting the batch grinding equation to the experimental data. The predicted powder size distributions were found to be in good agreement with the experimental data. The experimental results have shown that the mean size of product powder decreases as the size of the grinding media decreases. Keywords: population balance modeling, grinding, planetary mill, grinding media, grinding equation

Sep 1, 2012

By W. Pawlos

"The paper will present the methods of visual observation and recording of movement paths of coal grains of different physical properties in the paramagnetic liquid. The paths were recorded with a video camera in the working chamber by means of a specially constructed device, acting as a periscope, which were then transformed into digital images.Experimental movement paths were confronted to the paths obtained in a theoretical way by means of solving differential equations of movement. The outlet level of a grain of the same physical properties from the separator is a random variable with normal distribution which modal value is equal to the outlet level of a spherical grain, calculated from the solution of grain movement equations. At these assumptions it is possible to calculate the height of the passage from the separator working chamber to separate a given product with a given separation accuracy, measured by a probable error and to determine separation conditions."

Jan 1, 2003

By Sanggono Adisasmito

"The quality of the higher education in Indonesia is being improved by implementing a program financed by the World Bank under a project named QUE (Quality for Undergraduate Education). The investments are provided to selected study programs through a competitive selection process. The grant finances staff development, the purchase of equipments, textbooks, consumables, technical assistance, and incentives for outstanding faculties such as teaching grants, project grants, lecture note awards, and educational policy studies. These additional investments are provided to produce chemical engineering graduates that will compete beyond the national market.Chemical Engineering Department of Institut Teknologi Bandung in Indonesia has been selected to receive the QUE grant beginning the year 2000 and ending the year 2004. The department is actively involved in the mineral processing issues, particularly in the aspects of energy supply and the environmental protection. The activities are distributed in different laboratories and areas of expertise, such as: thermodynamics and utility systems, process equipment, chemical reaction and catalysis, microbiology and bioprocess engineering, process control, ceramics, as well as polymer and membrane technology. The main objectives of the QUE project are to improve the undergraduate program in the following aspects: Relevance, Academic atmosphere, Institutional management and commitment, Sustainability, as well as Efficiency and productivity, or abbreviated as RAISE. At the end of every fiscal year, the progress of the program is evaluated to measure the effectiveness of the project.The achievement of the QUE project objectives were assessed using performance indicators developed during the program design. There are six indicators to measure the performance of the individual program of study, such as: (1) Admission Test score, (2) average students' Grade Point Average (GPA), (3) average graduates' length of study, (4) graduates' waiting time before getting first job, (5) Test of English as Foreign Language (TOEFL) score, (6) Graduate Record Examination (GRE) score. Essentially, the RAISE evaluation criteria will be used to perform three main functions, such as (1) to measure the achievement through the six quantitative performance indicators, (2) to support the progress of evaluation and reporting throughout the implementation of the program, (3) to provide a universal framework for qualitative evaluation."

Jan 1, 2003

By Rhulani F. Maluleke, Francis W. Petersen, John H. Marsh, Johann de T. Steyl, Allan Nesbitt

"Pressure leaching of chalcopyrite and nickeliferrous pyrrotite at temperatures between 105 and 200 ºC has been proposed as a potentially viable route for the extraction of mineral elements from sulphide concentrates. In general, these concentrates contain iron, and the economic success of the processes is partially dependent on the choice of the environmentally acceptable iron-removal technique. One of the most widely used methods for the removal of iron from sulphate liquors is precipitation as hematite, goethite, or jarosite. The nature of the iron precipitate formed, dictates downstream dewatering and residue treatment and disposal options. However, a better understanding of iron precipitation under the defined process conditions would consequently be of benefit in process design and optimization.This study investigated the precipitation of iron in the autoclave at temperatures between 105 and 200 ºC. The effects of temperature, acid concentration, iron concentration, and the presence of other metal cations on the nature and composition of the precipitates were determined."

Jan 1, 2003

By R. Roufail

In this paper, the effect of different operating parameters of high speed stirred mill on the particle breakage mode is addressed. Morphological features of broken particles is investigated and related to the types of forces generated in the mill using Discrete Element Method (DEM). The stress intensities generated in the mill are varied by changing the agitator speed. The investigated agitator speeds were 1000, 1500, and 2000 revolution per minute (rpm). The minerals considered in this study are hard minerals (quartz) and soft, sulphide minerals (galena). The morphological features examined are roughness, roundness and elongation, which shed light on the mode of breakage during the grinding process. Particles that are rough, less round and elongated would imply that they broke via fracture, along their grain boundaries. On the other hand, the smooth, less elongated particles would mean breakage occurred across the grain, which is abrasion mod. DEM study complemented the understanding of particle breakage mechanism via tracking the types of forces applied on the particles. Normal forces imply compressive loading, which is presumed to impose fracture breakage along the grain boundaries, whereas tangential forces imply abrasion loading. Stirred mill grinding has been regarded as an attrition/abrasion process, whereas, this study showed that about 60% of total particles that are morphologically analyzed for both minerals were rough particles. Such an observation indicates that the fine product, which contain a significant amount of progeny from the coarse fractions are consistently broken via fracture. The morphology results agreed with the DEM findings, which indicated that the agitator speed, mineral type, and residence time would dictate the type and mode of particle breakage. Keywords: DEM, high speed stirred mill

Sep 1, 2012

By Y. Y. Zhou

This paper introduces the application of CRIMM high-gradient magnetic separator in refinement of feldspar powders as well as the supporting technical outfits needed by the refining process with the high-gradient magnetic separator as main equipment. It could reduce the content of Fe2O3 to 0.03% with a deferrization rate of 85.88% from the feldspar raw ore containing 0.17% Fe2O3by using the above refining technology, producing an ultrapure feldspar product.

Jan 1, 2014

By Y. Q. Qui

In the bauxite flotation process for desilication, the middling treatment mode is the important factor to raise the flotation recovery of the preparation concentrate. The middling treatment mode mainly depends on A/S and the size composition. However, similar ratio of A/S should not be the single factor of re-dressing, size composition plays an important role also. Re-dressing the middling mixed with the tailings of concentrated to the rough ground for desilication and the concentrate of scavenged to the fine ground for desilication to raise the recovery of 5.83%, when compared two flow sheet schemes.

Jan 1, 2014

By V. Tsyplakov

This article reviews factors of preg-robbing effect, occurring in the course of pressure oxidation of ore and concentrates, containing chloride compounds and so-called &apos;organic carbon&apos;. The article also summarizes the main results of the studies and testwork conducted to overcome this effect. The following efficient preg-robbing mitigation methods have been noted: higher temperature of pressure oxidation process, preliminary removal of natural carbonaceous material from concentrate, chloride removal prior to concentrate pressure oxidation, and addition of water-soluble organic blanking agents, which suppress the adsorption activity of the native ore adsorbents. Keywords: preg-robbing, double-refractory gold concentrates, pyrite, arsenopyrite, blanking agents, pressure oxidation, autoclave leaching

Sep 1, 2012

By John Ralston, Stephen Grano, Yongjun Peng, Daniel Fornasiero

"A specially designed mill which allowed the control of pH throughout grinding was used to study the effect of rgrinding conditions on galena flotation and galena separation from pyrite. The various reactions occurring on the mineral surface were investigated by a range of techniques, including OH- addition to maintain the grinding pH, EDTA extraction, XPS and ToF-SIMS measurements.Galena flotation and galena separation from pyrite were strongly dependent on the metal oxidation species produced on galena and pyrite surfaces under different grinding conditions. Iron oxidation species depressed both galena and pyrite flotation, whilst lead oxidation species activated pyrite but had little effect on galena. Optimum galena flotation and galena selectivity against pyrite were achieved by selecting grinding conditions that enabled lead and iron oxidation production to be controlled."

Jan 1, 2003

By Elzbieta Mielczarski, Jerzy Mielczarski, Jan Drzymala, Yann Duval

"The monoalkyl ethers of polyethylene glycols are universal flotation reagents because they can be used as collectors, frothers, surfactants, and depressants. Their collecting power was demonstrated for different minerals including coal and quartz.It was confirmed in this work that monoalkyl ethers of polyethylene glycols could be used as collector in flotation of quartz in a monobubble Hallimond cell. Since feldspar does not float in the same cell, it was also shown that selective separation of quartz and feldspar in the Hallimond tube is possible. However, a trail to use the monoalkyl ethers of polyethylene glycols compounds for separation of quartz and feldspar by flotation of mixture of these minerals in a Mechanobr laboratory flotation machine was futile, indicating that these reagents required special environment for flotation.Most probable parameter responsible for a decrease in quartz flotation in the flotation machine is the hydrodynamics of process, and different adsorption/desorption conditions. To prove this, another series of experiments was carried out to separate quartz and feldspar, in which a laboratory flotation column was utilized. The performance of the flotation column was in between that of in the Hallimond tube and flotation machine. These experiments confirmed that the hydrodynamics of flotation plays a vital role in flotation of quartz with monoalkyl ethers of polyethylene glycol compounds."

Jan 1, 2003

By Peter N. Holtham, Mary M. Ng

"Resistivity measurements of minerals in the laboratory are commonly made with a low DC voltage source. Common test voltages specified in the ASTM Standard D257 are 100, 250, 500, 1000, 2500, 5000, 10000 and 15000 V, however 100 and 500 V are the most frequently used. Resistivity results obtained in the laboratory have been used to infer the electrical behaviour of minerals undergoing electrostatic separation. However because the voltages employed in electrostatic separation in the plant are of the order of thousands of volts, typically greater than 15000 V, whether the laboratory results are applicable as a predictor of plant performance is a critical question. It is unclear whether resistivity values taken at a low voltage are characteristic of those seen in electrostatic separation, in which the minerals are exposed to a much higher voltage. No definitive answer could be found in the literature.In this work, the resistivities of zircon, rutile and ilmenite were measured in a corona field for the first time. The measurement principle was based on a technique developed to measure fly ash resistivity in electrostatic precipitators, however the test apparatus and findings are novel.Resistivities of rutile and zircon were found to be easy to measure. The values measured in a corona field were several orders of magnitude less than those obtained with a dc voltage of 100 V. Evidence of back corona was observed with zircon. When the voltage drop was greater than the sample layer could withstand a localised electrical stress developed, resulting in a voltage breakdown, at which point a sudden surge of corona current (back corona) was detected in the sample layer. Rutile, on the other hand, exposed to the same conditions as that of zircon (i.e. same temperature and applied voltage) did not exhibit any sign of back corona. Its resistivity across the range of test voltages (14 to 33 kV) remained fairly constant."

Jan 1, 2003

By B. K. Mohapatra

Small manganese ore bodies in south Odisha, India occurs both as stratiform and stratabound ore bodies. These two ore bodies show contrasting mineralogical, petrographical and chemical characteristics. Stratiform type of Mn-ores consists of manganese, iron and silicate- phases in approximately same proportion. In contrast, stratabound ore bodies contain a high proportion of manganese oxides, silicates and phosphorus phases. Phosphorus is found within apatite in the stratabound ore bodies while in the stratiform ore it occurs as an adsorbed state with iron phase (goethite). Both ore bodies are low-grade (17-23% Mn) therefore do not have a market value. However, the stratabound ores are enriched in phosphorus (P2O5: >1%) compared to the stratiform ores. Both the ore types were processed through gravity, magnetic and roast reduction followed by magnetic separation techniques. The strata bound ore could be upgraded to 33% Mn from a feed of 23% by combination of dry and wet magnetic separation methods. But the phosphorus content also suits up (P2O5: 1.2%) in the processed product making it unsuitable for further use. The stratiform ores do not respond to either gravity or magnetic separation because of close association of manganese with iron phases. However, this could be beneficiated through roast reduction followed by magnetic separation. An ore with 17% Mn content could be upgraded to 40% Mn with a 42% yield and 78% recovery. The goethite, having phosphorus, converts to magnetite and is retained within the magnetic fraction, thereby reducing the concentration of phosphorus in the non-magnetic fraction, which becomes the product. This report demonstrates the influence of ore petrology in determining the up-gradational potential of manganese ore in the southern Odisha, India. Keywords: manganese ore, physical beneficiation, phosphorus rich ore

Sep 1, 2012

By R. ?. Shishmarjov, Yu. ?. Davidenko, S. V. Bukhalov, ?. S. Baksheev, M. S. Shkirya, N. ?. Aikasheva, D. V. Bogdanovich, ?. Yu. Faustova

"The goal of prospecting operations in the Republic of Altay was to locate gold-sulfide-quartz mineralization. For this purpose we applied the technology of electromagnetic sounding and induced polarization (EMS-IP). These operations resulted in localizing promising sites with presence of sulfidization. The EMS-IP method proved to be highly efficient amongst other prospecting methods targeted at recognizing zones of sulfide mineralization making up 91%, considering that in more than half cases the ore intervals were the case. In the Yakutian diamondiferous province the EMS-IP technology was approbated during three field seasons to accomplish the assignments on searching for kimberlite bodies under conditions of various geological types. As a result, the reference objects were distinguished, and geoelectric parameters of kimberlite pipes of explosion were defined.INTRODUCTION In the time span 2015-2016 in Gorny Altay the EMS-IP technology was approbated in the Novokuznetsk area. The on-land areal geophysical survey was performed by EMS-IP method applied to identify, outline and locate promising sites with Au-Ag-bearing polymetallic mineralization within surveyed areas. Compared to the hosting rocks, the sulfides contained in polymetallic mineralization are typified by low specific electrical resistivity (SER) and high polarization. The areal survey conducted via EMS-IP method provided spatial characteristics of searched object. From July 2016 to August 2017 our expedition group carried out serial test works and laboratory investigations intending to define performance capabilities of EMS-IP technology in searching for kimberlite bodies under conditions of diverse geological types. The prerequisites for serial work were operations accomplished at the «Listvenichny» site lying 35 km away from Mirny town in the Sakha Republic (Yakutia), where the EMS-IP technology was probed for locating position and measuring geoelectric parameters of tuff pipe «Buardakhsky». After successful completion of operations it was decided to evaluate geoelectric parameters of kimberlite pipes of explosion."

Jan 1, 2018

By Johan Nell, Paul den Hoed

"Carbochlorination tests were conducted with matched particle-size fractions of rutile, ilmenite and hightitania slag in a small bubbling fluidized-bed reactor. The effects of temperature, the type and proportion of solid reductant in the charge, and the fraction of Cl2 in the fluidizing gas were investigated. Tests confirm the need for solid carbon in the bed if chlorination is to run at high rates. With solid carbon in the bed, CO supplied with the fluidizing gas does not increase significantly the degree of chlorination after 75 minutes.When large proportions (30 wt%) of carbon are added to the charge, then the reactionTiO2 + 2C + 2Cl2 = TiCl4 + 2COis favoured overTiO2 + C + 2Cl2 = TiCl4 + CO2Ilmenite is chlorinated more quickly than titania slag, which in turn is chlorinated more quickly than rutile. Rates of chlorination at 1100°C and 1000°C are much the same and significantly higher than at 900°C. Chlorination is associated with significant increases in particle porosity (even for rutile), which is brought about by the rapid initial chlorination of FeO and MnO (in ilmenite and slag) and (it is argued) by the chlorination of Ti2O3 which forms at high-energy surface sites."

Jan 1, 2003

By P. C. Beuria

Iron ore concentrate contains different mineral phases viz. hematite, magnetite, goethite, kaolinite, and gibbsite. Presence of some of these phases like goethite, kaolinite, and gibbsite contribute to the loss on ignition (LOI) content of the sample. Iron ore fines (pellet feed) are pelletized for utilization in DRI & BF processes. In the present pelletization technology i.e., straight grate and grate kiln processes, the LOI in the ore should be within the range of 2.0-2.5%. LOI content in the iron ore concentrate is found to be more than 4% after beneficiation of low-grade iron ore. It is therefore difficult to produce good quality pellet because of high LOI content. The LOI content of the sample is a detrimental factor in the pellet making. For effective pelletization, the LOI content in iron ore fines needs to be reduced before pelletization. It can be reduced by fluidized bed roasting. The objective of present work is to understand the kinetics of removal of LOI from iron ore fines. The effects of bed depth, temperature, and residence time on reduction of LOI content in iron ore fines were studied using muffle furnace. The process of roasting was carried out at four different temperatures varying from 400 to 950 °C with a variable residence time of 30, 45, 60 & 75 minutes and at bed depths of 16, 32, 48 & 64 mm. In all instance of experiments carried out, one of the parameters was kept constant. It was observed that at 850 °C and 30 minutes of residence time, there was sufficient removal of LOI in static bed condition even at a high bed depth of 64 mm. Keywords: LOI, pellet feed, fluidized bed roasting, goethite

Sep 1, 2012

By D. Endara, E. De la Torre, S. Echeverria

"The study was conducted with the sulfide mineral from the province of Zamora Chinchipe. It was characterized physical, chemical and mineralogical, obtaining between its main results a copper concentration of head ore of 0,58 %. The mineral was homogenized and taken to direct closed circuit: rollers mill - vibratory sieve (mesh # 16). Flotation was carried out in two stages: the collective and selective where in each one were performed 6 water recirculation as suggested by the technique used to relate information of a batch flotation to a continuous circuit called cyclic flotation tests (LCT). In the collective flotation (bulk) 2 Kg of mineral were grinded with 10 Kg of balls for 30 minutes and 62.5% of solids, the pulp was taken to the flotation process with solids percentages of 33.3% and pH 7, it was conditioned with 45 g / t of KAX 1%, 50 g/t of Aerofloat 208 and 20 g /t of Pine oil. The concentrate and tailings bulk obtained were filtered separately for the recovery of water and it was recirculated to the next grinding of 2kg mineral. In the selective flotation 1Kg of bulk concentrate was carried to regrind for 40 min, 62.5% percent of solids, 10 g of lime and 5 g of tannin FLOATAN T5, the pulp was taken to the roughing-collection-refining flotation circuit controlling the pH between 10.5 and 11 where conditioning (60 g/t of Aerofloat 208 and 30 g/t of Pine oil) and adding lime to the circuit and FLOATAN according to the procedure. The four fractions obtained from the circuit were filtered; the water was recirculated to the regrind process of the bulk concentrate. In the collective flotation process tends to stability in the fourth recirculating water to obtain a copper content of 4.5% and a recovery of 87%, recirculated water represents 69.8% of all water used in the 6 recycles. In the selective flotation circuit the fifth recirculating of water is the optimal where obtaining a copper content of 13% and a recovery of 72%, recirculated water in the selective flotation circuit represents 95% of the total water used in the 6 recycles."

Jan 1, 2018