Search Documents

By K. Lillkung

The use of secondary sources has become a very attractive option in the production of platinum group metals as the demand for these metals has increased. One of the promising sources are the spent catalysts, which provide an attractive source as they have relatively high metal content compared with the ores where the metal is originally extracted from. The concentration of platinum group metals in catalytic converters is in the range of 0.1-1 mg/g as the concentration in ores is usually less than 10 ppm. Aqueous chloride solutions are claimed to be a cost effective way in which platinum group metals can be brought into solution and concentrated. In this work the effect of different parameters on the dissolution rates of Pt, Pd and Rh were investigated. The parameters investigated were the Cl- concentration, the temperature and applied potential. Chloride concentrations used were 62.5, 90, 125 and 250 g/l. Temperatures were 25, 40, 60, 80 and 94°C. Potentials were 950, 1050, 1150 and 1250 mV vs. SCE for Pt and Rh and 380, 410, 440 and 470 mV vs. SCE for Pd. Dissolution rates were calculated from the current densities determined by potentiostatic measurements. Thin wire electrodes were used in the measurements. As expected, higher temperature, higher potential and higher chloride content generally increasedthe dissolution rate. However, the effect was nonlinear and slightly different for different metals. The results show that strongly oxidizing conditions are needed in order to achieve reasonable dissolution rates. With the highest chloride content and at potential of 1250 mV vs. SCE and 94°C the dissolution rate of Pt was nearly 1 mm/h, whereas in similar conditions Rh achieved a rate of only nearly 100 µm/h. Similarly, with the highest chloride content and at potential of 470 mV vs. SCE at 94 °C the dissolution rate of Pd was nearly 1 mm/h. Keywords: Pt, Pd, Rh, redox potential

Sep 1, 2012

By Jaime Sepúlveda

"A broad diversity of critical operating conditions may influence, in very convoluted ways, the actual performance of any given mineral processing system, to the extent that it becomes nearly impossible to empirically determine the independent, decoupled impact of each condition. An effective approach to better understand the behaviour of such complex systems is via the extensive use of sufficiently detailed and reliable mathematical models, allowing the process analyst to explore and learn about the independent effect of all relevant operational conditions. Certainly, these tasks are greatly facilitated if the appropriate software tools - such as the Moly-Cop Tools software package - are readily available. Moly-Cop Tools 3.0 is a set of 63 easy-to-use EXCEL spreadsheets designed to help process engineers characterize and evaluate the operating efficiency of any given grinding circuit, following standardized methodologies and widely accepted evaluation criteria. Moly-Cop Tools 3.0 covers conventional and semiautogenous mills, crushers, HPGR’s, rod mills and vertimills, with the corresponding mass balance and parameter estimation routines; plus complementary spreadsheets regarding Bond’s Law calculations, grinding media selection and performance evaluations and other useful utility functions. As a relevant example of application, specifically focusing on semiautogenous grinding operations, the current publication describes how the models can help us learn and rationalise critical empirical observations such as the relationship between feed particle size and optimal ball filling, the role of the rocks as autogenous grinding media as well as the impact of feed size and discharge grate opening on the mill grinding capacity. Over the last 20 years, Moly-Cop Tools has gained wide acceptance around the mineral processing community in recognition to the quality of the mathematical models contained, their simplicity of application and ease of sharing of the calculations amongst all interested parties, since it is available free-of-charge with no restrictions to make as many copies as needed."

Jan 1, 2014

By Cheng Xiang, Nan Ye, Xinyuan Ke, Yang. Jiakuan, Huabin Wang

Bayer red mud is a highly alkaline residue produced by the alumina industry through the Bayer process. Its disposal is a worldwide problem. The high alkali content and poor pozzolanic activity is aconstraint for its utilization on construction materials. In this study, the red mud was activated through an alkali-thermal method to improve its activity so that it can be utilized in geopolymerization. The red mud was mixed with different amounts of sodium hydroxide, and calcined under 800 °C to produce geopolymer precursors, and then mixed with water directly to prepare one-part geopolymer. X-ray diffraction was conducted to study the phase transformation of red mud and the mechanism of its geopolymerization. Nitrogen Isothermal Adsorption tests were conducted to analyze the pore structure of the geopolymer binders. The results show that calcinations with alkali would promote the Al in red mud transforming into glassy SiO2 to form the N-A-S phase which is soluble in water. When the red mud was calcined at 800 °C with a Na2O addition more than 10%, the dissolving of Si and Al from red mud was greatly improved. The thermal-alkali activated red mud with 10% Na2O obtaining a compressive strength of 9.77 MPa after it reacted with water and cured for 7 days at 20 °C and 95% RH. But the strength decreased as the curing time extended to 28 days. The reason is suggested to be that the polymerization of Al-O and Si-O is unstable due to the low Si/Al ratio of red mud. The alkali in the structure dissolves again into the pore water and corrupts the pore structure. Therefore, the thermal-alkali red mud should be combined with other reactive aluminosilicate materials such as granulated blast furnace slag to absorb the alkali released by the thermal-alkali red mud at the latter curing days.

Jan 1, 2014

By Fangming Liu

The key problems of current flowsheets and equipments are analyzed. A new steel slag's crushing flowsheet whose key equipments are the improved inertia cone crusher and inertia vibrating jaw crusher is proposed. An advanced two stage open-circuit crushing method is adopted in the flowsheet, with 90% of particle size crushing under 6mm. Using inertia vibrating technology and selective crushing principle the crushers can realize steel slag separating fully into steel and slag and with flexible transmission mechanism the crusher can be protected when iron lump is passing. The flowsheets can enhance the recovery of metal greatly, and expand the application range of tail slag and added value.

Sep 1, 2012

By M. Maldonado

A flotation bank is a serial arrangement of cells. How to optimally operate a bank remains a challenge. This article reviews three reported strategies: air profiling, mass-pull (froth velocity) profiling and Peak Air Recovery (PAR) profiling. These are all ways of manipulating the recovery profile down a bank, which may be the property being exploited. Mathematical analysis has shown that a flat cell-by-cell recovery profile maximizes the separation of two floatable minerals for a given target bank recovery when the relative floatability is constant down the bank. Available bank survey data are analyzed with respect to recovery profiling. Possible variations on recovery profile to minimize entrainment are discussed.

Sep 1, 2012

By D. I. Verrelli

Within the flotation community a belief has developed that some particle shapes are more ?floatable? than others. This is usually attributed to an influence of particle shape or roughness on the induction period required to achieve attachment between the particles and the air bubbles in the pulp. Up to now, such measurements have not been able to readily isolate the effect on individual flotation subprocesses. In contrast, our experimental apparatus, the CSIRO Milli-Timer, enables us to directly observe the process of particle?bubble interaction and attachment by means of a high-speed video recording, thus providing a direct measure of the induction period for attachment. To assess the influence of particle shape on induction time we used two varieties of methylated borosilicate glass particles ? spheres and angular ?frit? ? in a range of tightly-sized fractions. In doing this, we take care to account for the influence of other factors that could affect the induction time, such as the polar angle of sliding commencement, and approach velocity. These parameters are recorded as variables for each interaction, and corrected for using multiple nonlinear regression. Our results illustrate the importance of particle shape on induction period, with angular particles exhibiting induction periods that were an order of magnitude lower than those of spheres. Furthermore, the induction period was seen to decrease with increasing particle velocity, or kinetic energy on approach, but increased as the trajectory approached the limit of just grazing the bubble. Particle shape in mineral processing is a consequence chiefly of the mineral type and the type of grinding employed. The results presented herein indicate that attention should be paid to the shape of particles obtained from the grinding operation, besides particle size. Keywords: attachment, bubbles, flotation, induction period, particles, shape effects, surface roughness

Sep 1, 2012

By C. Dorfling, W. A. Rossouw

"Hydrometallurgical processes used for metal recovery from waste printed circuit boards (PCBs) typically involve dismantling, shredding and physical separation prior to successive leaching stages for selective dissolution of different metals. The principles of the physical separation units are well understood, but valuable metal losses of more than 30 % can be incurred during these processing steps. The impact of the physical separation units’ performance on downstream leaching operations have not been defined; this prevents the development of a well-integrated process. The objective of this project was to determine to what extent the base metal leaching behavior depends on the physical separation pre-treatment. PCBs were shredded to 100 % passing 2 mm before physical separation by dense medium separation (DMS) as well as magnetic separation. Batch leaching tests using various concentrations of sulfuric acid were conducted on three feed fractions: (1) shredded PCBs without any physical separation, (2) heavy fraction recovered from DMS, and (3) non-magnetic fraction recovered from the DMS heavy fraction. DMS increased the metal content in the feed from 48 % to 75 % on a mass basis, but 70 % of the gold and 20 % of the copper reported to the light fraction. The application of magnetic separation to the heavy fraction produced by DMS removed 67 % and 61 % of the iron and nickel, respectively, while negligible amounts of non-magnetic metals were removed. Although DMS successfully concentrated the feed and magnetic separation removed the majority of iron and nickel, these steps did not result in any improvement in the rate or extent of copper leaching. Metals generally leached faster when the sulfuric acid concentration was increased from 1 M to 2.5 M; this effect was seen to be more pronounced for pretreated feed. INTRODUCTION The fast rate of technological development has led to a decrease in the service life of electronic devices. This is resulting in an increased rate of electronic waste generation. The recovery of metals from electronic waste is of environmental and economic interest. The majority of these metals are typically located on printed circuit boards (PCBs) within electronic devices (Tuncuk, Stazi et al., 2012). Hydrometallurgical processes are considered a viable option for small scale metal recovery from waste PCBs, and generally involve the following steps: disassembly for removal of hazardous and reusable parts, size reduction, physical separation, successive leaching stages for metal dissolution and finally recovery of metals from leach solutions."

Jan 1, 2018

By Y. Foucaud, I. Filippova, L. Filippov

Flotation is the most common beneficiation route for tungsten ores, but the predominance of minerals with similar surface properties poses a real challenge. This study investigates the use of Falcon centrifugal separators for gangue minerals removal and desliming prior to flotation. A typical tungsten-bearing skarn ore (Tabuaço, Portugal) is used, containing scheelite (CaWO4) associated with dense calcium-bearing silicates (vesuvianite), fluorite, apatite and light silicates (feldspars) as gangue minerals. Two types of Falcon bowls (Falcon UF and Falcon SB) were used, prior to flotation tests with fatty acids as collectors and a combination of sodium carbonate and sodium silicate as gangue minerals depressants. This flowsheet was compared with a reverse configuration, using flotation prior to Falcon concentrator, and with a classical flowsheet, using hydrocyclone and flotation. Gravity pre-concentration and desliming with the Falcon concentrator were optimized through the design of experiments (DoE) methodology. The influences of pulp density, rotational speed, feed flowrate and fluidisation pressure (for the Falcon SB) were studied for both bowls. Results showed that the Falcon can be used as a desliming and pre-concentrating apparatus. Separation performances depend mainly on rotary speed and pulp density for the Falcon UF, whereas rotary speed and fluidisation pressure are the main parameters for the Falcon SB. With only one stage of Falcon SB, an enrichment ratio of 7.9 is obtained with a 65% WO3 recovery while 89% of apatite and fluorite are rejected, which constitutes a very good selectivity. In comparison, Falcon UF shows lower enrichment ratios, around 2.7. In terms of desliming, Falcon UF is as efficient as the hydrocyclone, while the Falcon SB is significantly more efficient. Hence, the use of Falcon SB prior to flotation improves the overall performance of the tungsten flotation route by desliming the flotation feed while pre-concentrating the scheelite. It impacts very advantageously the flotation, as most of the calcium-bearing minerals are eliminated. A Falcon SB stage prior to flotation yields a final concentrate grade of 29.7% WO3 with a recovery of only 36.8 % that should be optimized as the reagents dosages were not adapted to the pre-concentrated feed.

Jan 1, 2018

By M. Gonzalez Fernandez

"Commercially introduced in 2004, the SAGDesign™ test has today proved its efficiency for sizing SAG mills for a wide variety of ores, from very soft to very hard ones. The interest of building a model using the SAGDesign™ test specific energy is the introduction of such a model into a complete process simulator making it possible to predict a complete material balance. The developed model compares the required specific energy with the energy provided by the mill. This energy calculation is derived from the Austin Power Formula. The specific energy provided by the test is corrected, using various parameters, such as the Ball Mill Work Index, to take into account the true operating conditions, the feed and product sizes. The core of this model allows the determination of the product d80 using the mill geometry, its operating conditions and of course the SAGDesign™ test results. To be included in a simulator, the model must also predict the overall size distribution of the SAG mill discharge. Assumptions to answer this point are presented here. The model has been implemented in the USIM PAC simulator. It is used either to predict the product size distribution for a given SAG mill, but also to size a SAG mill for getting a required reduction ratio. INTRODUCTION Over the last few years several types of new comminution machines have been introduced in the market. The most notable newcomer was the HPGR (Morley, 2006). But, even when these machines have some advantages, they have not earned the trust of the mining industry. That is why the established technologies still being the first choice. And, in comminution, that first choice are SAG and ball mills. The design of ball mills has been well understood for a long time. The Bond Ball Mill Work Index is the standard test which helps to describe the ore in terms of energy requirements for milling. Unfortunately, the development of an equivalent test to characterize the ore subject to SAG milling has taken some time. As of today, several tests are available in the market, like the MacPherson test, the MinnovEX SAG Power Index (SPI™), the JK Drop Weight Test, the SMC Test® and the SAGDesign™ test (Verret et al., 2011). The SAGDesign™ test, developed by John Starkey in Canada in the early 2000s (Starkey et al., 2008, 2015), has become one of the standards to assess the grindability of an ore in a SAG mill. One of its advantages is the reduced sample mass needed to perform it, hence, the reduced cost. The second one is that the output of the test is straightforward, it is the energy required to grind the ore between two sizes. Because of this energetic approach, the results provided by the test can be directly applied to size a new mill or to assess the performance of an existing mill."

Jan 1, 2018

By Eberhard Gock

The worldwide implementation of corrosion protection of low alloyed automotive metal sheets by zinc coating has led to supply shortages of zinc free non-alloyed steel scrap in the foundry industry. In a collaboration project, partly financed by the German government, with partners from the automotive industry, zinc metallurgy, scrap trading, foundry industry, and plant construction, a new acid-based pre-dezincification process has been developed, and a pilot plant with throughput of about 100 t/d has been put into operation at the Clausthal Umwelt-Institut GmbH (CUTEC) together with the Clausthal University of Technology in Germany. During the treatment process, acid from a zinc metallurgical plant will be supplied, which can be recycled to the primary zinc extraction process after raising the zinc concentration to more than 130 g/L zinc. This way, the separation of small amounts of iron by precipitation and the electrolytic zinc winning are outsourced and, as a result, the pre-dezincification process runs waste-free. In Germany, the amount of zinc coated ?new scrap? is approx. 3 million t per year with a zinc content of approximately 60,000 t per year. The possible additional incomes for the dezincified steel scrap are in the order of ?40 to ?50 per ton of scrap, the gained zinc content during the acid dezincification defrays the costs of the process, if the throughput is more than 700 t/d. In comparison to conventional dezincification during the electro arc furnace process followed by upgrading in a rotary kiln (Waelz process), the acid dezincification process running at a maximum of 50°C will cut the energy costs by up to 74% and the CO2 emission by up to 88%. In fact, a demonstration plant is being designed right now and will be installed for processing a part of the zinc coated metal scrap from the Volkswagen AG in Wolfsburg, Germany. Keywords: steel scrap, zinc-coated steel, dezincification methods, acid

Sep 1, 2012

By Naoki Hiroyoshi, Hajime Miki, Tsuyoshi Hirajima, Masami Tsunekawa

Acidic solutions for chalcopyrite leaching contain cupric, ferrous and ferric ions, and the oxidizing power of the solutions is indicated by a redox potential, determined by the concentration ratio of ferric to ferrous ions. This paper reviews our previous studies on the redox potential dependence of chalcopyrite leaching in sulfuric acid solutions. Leaching and anodic-polarization experiments showed that coexistence of cupric and ferrous ions activate anodic dissolution of chalcopyrite, causing faster copper extraction at the potentials below a certain value (critical potential). The analysis of the AC impedance spectra for chalcopyrite electrode indicated that a high-resistance passive layer grows on the chalcopyrite surface without cupric and/or ferrous ions, and that coexistence of these ions causes a formation of another product layer and inhibits the passive layer growth at low potentials. These results are explained by a reaction model assuming the formation of intermediate Cu2S due to chalcopyrite reduction and the subsequent oxidation of the Cu2S. The critical potential corresponds to the redox potential of the Cu2S formation and the predicted values matched with the experimental results. Catalytic effect of silver ions on chalcopyrite leaching was also discussed based on experimental results and the above model.

Jan 1, 2003

"This research aims at improving the beneficiation of coals and minerals in fine and ultrafine size fractions. A widely used method for upgrading fine and ultrafine particles is froth flotation, which is generally classified into mechanical flotation and column flotation. The present work is focussed on column flotation. A flotation column equipped with a conventional bubble diffuser/sparger was used with oscillatory air supply generated using a fast-switching solenoid valve. The flotation tests were carried out for coal particles and mineral particles, respectively, and a comparison in flotation performance was made between oscillatory air supply and steady air supply. It was found that use of oscillatory air supply with a proper valve switching frequency and on/off time ratio to replace steady air supply could lead to increased recovery of coals or minerals by more than 14 percentage points and substantial reagent cost savings. The improved flotation performance was attributed to enhanced gas dispersion and flow conditions. This research offers a simple new approach to improving the beneficiation of fine coals and minerals with using flotation columns.INTRODUCTIONFroth flotation has been widely used for the separation and concentration of fine coals and minerals by exploiting the difference in their affinity to air bubbles in aqueous medium. Froth flotation is an effective method for beneficiation of coal and mineral particles in a certain size range. It remains difficult to upgrade ultrafine mineral particles. One of the reasons for the ineffective flotation of fine particles is the low probability of bubble-particle collision in the collection zone (i.e., the pulp zone). According to Reay and Ratcliff (1973) and Yoon and Luttrell (1989), the probability of collision is significantly affected by bubble size and particle size, and the collection zone recovery can be increased by decreasing the bubble size."

Jan 1, 2018

By Gurubasayya Swamy

This paper presents the performance study of sag mill in the processing of gold ore. Deterioting ore grade and high demand of metals has tremendously influenced the SAG mills. Today?s high capacity Semi-autogenous grinding (SAG) mills expand vast amounts of energy and in doing so consume tons of shell liners and steel balls, while processing ore. Semi-autogenous (SAG) mill performance is influenced by ball charge, feed properties, shell, grate, and pulp lifter design. In the performance study of SAG mill, based on the results obtained it can be observed that SAG mill performed better at feed size +4 inch and grinding media consumption 0.90kg/mt. In the present study the effect of crusher bypass on SAG mill performance, an immediate drop of throughput ranging from 10-20tph is observed. Keywords: sag mill, pulp lifters, grinding media, energy, consumption, throughput

Sep 1, 2012

By P. Yu, L. X. Liu

"A mechanistic model for tumbling mills was developed during PhD studies at the JKMRC. The concept was presented at the IMPC of 2014, followed by progress in a sub-process of the model presented at the IMPC of 2016. Additionally, a number of papers on the sub-models and breakage function have been published. This paper provides a consolidated summary of the outcomes and status of the model. The overall model structure is presented along with the sub-models such as appearance functions, breakage rate functions, energy distribution, transport, and multicomponent grinding interaction model. The strengths and capabilities of the model structure as achieved to date are presented. The gaps in knowledge and sub-processes are also presented, providing a guide to the areas that require further research and development. It is proposed that the approach developed in this paper provides a structure that can accommodate future mechanistic, dynamic mill model evolution that can incorporate the latest research outcomes and provide a platform to test modelling improvements. This can assist in substantially improving the predictive mill modelling capability in the industry, the importance of which should not be underestimated for this workhorse of mineral processing.INTRODUCTION Grinding is almost the largest single energy-consuming process in the mineral processing industry, which was estimated that about 0.2% of global, and 1.3% of Australia’s electricity is consumed by comminution of gold and copper ores (Ballantyne and Powell, 2014). Although there are some relatively new grinding mills, such as stirred mills, vibrating mills and HPGRs (High-Pressure Grinding Rolls), etc., tumbling mills, as the traditional grinding facilities, are more extensively used."

Jan 1, 2018

By Xinyang Xu, Chen Zhang, Lixia Li, Zhitao Yuan

"Density functional theory was employed to clarify the mechanisms of the activation of a quartz surface and its collection by the flotation method at the molecular level. The calculation results indicated that hydrogen bonds on the quartz surface (1 0 1) existed in pairs while in contact with water. The simulation was carried out to investigate the different effects of Ca2+ and Ca(OH)+ on a quartz surface with hydrogen bonds, and the results suggested that Ca(OH)+ most likely adsorbed onto and activated the quartz surface. Mulliken population analysis of the external oxygen atom of the quartz surface, calcium atom of Ca(OH)+, and the oxygen atom of oleate showed that there were electron transfer and the formation of a chemical bond between Ca1-O1 and Ca1-O3, which were indicative of strong interactions between the three atoms. In addition, the –OH of the Ca(OH)+ contributed to the activation, which suggested that the Ca(OH)+ group acted as a bridge between the surfaces of oleate and quartz.INTRODUCTIONFlotation is an effective separation method in mineral processing that takes advantage of the physicochemical differences between minerals and gangue, and the properties of the mineral surfaces play a key role in this process (Liu et al. 2016, Qin et al. 2017). In the reverse flotation process of iron ore, gangues are captured by cationic or anionic collectors and floated with air-bubbles as tailings, and the pre-depressed iron oxide minerals are left at the bottom as concentrates (Lima et al. 2013, Yianatos et al. 2015, Zhu et al. 2015). Quartz (SiO2) is one of the major gangues of hematite ores and cannot be easily removed. It is a naturally hydrophilic mineral, in which silicon is the cation in its crystal structure and has very limited solubility. Therefore, quartz must be activated, usually by metal ions, for its effective rejection as a float-product by reverse flotation (AIME. et al. 1976)."

Jan 1, 2018

By Arkady Senchenko

The paper deals with the problem of refractory gold-containing material processing. It is observed that all traditional methods for liberation of fine gold from this type of products are characterized by a number of essential disadvantages, where the main ones are ? considerable expenses for ore processing and big environmental impact. As an alternative to the existing methods there is considered a gold liberation method, which is based on the combination of ultra fine grinding process with the consequent atmospheric oxidation. The theoretical justification of atmospheric oxidation was carried out, in the result of this the mechanism and the degree of sulphide minerals? oxidation was found out, the dependence of gold dissolution speed on the slurry content in liquid phase produced by grinding and oxidation was identified. The experimental data and results of pilot-plant testing are given and the most effective grinding and atmospheric oxidation mode is selected on this basis. The performed complex of research works allowed us to use the provided technology at the gold processing plant having capacity of 8 mln. tons of ore per year. The questions, problems, advantages and disadvantages of atmospheric oxidation technology for refractory gold-containing concentrates are considered in this paper. Keywords: refractory gold-containing material processing, gold liberation method, cyanidation

Sep 1, 2012

By Máximo Pérez, Julio C. Videla, Rosa Dzioba

"This paper reports the hydrometallurgical treatment of gravity concentrates of gold samples and outcrops associated with graphite ores obtained from:- flotation tailings of crystalline graphite minerals- outcrop samples of graphitic rock associated with auriferous minerals and free gold located in the Villa Union district and surrounding areas - La Rioja Province - Argentina.Previous studies of the flotation potential of crystalline graphite minerals failed to consider the presence of noble metals.The samples represent a mineralized zone of crystalline graphite which is distributed in different formations with a NE - SW trend in Maz, Punta Colorada and Las Ramaditas hills, covering an area of about 300 square kilometers.The most important variables affecting the leaching process, such as grain size, mineralogical species, reagent consumption, and so on, were previously studied. (Weiss, L.1985)On the basis of the present study results, the possible definition of an economically viable mineralization will be analyzed to define an auriferous district."

Jan 1, 2003

By Ofra Damm, v du Preez, D. van Vuuren, L. Simpson, H. Chikwanda

"South Africa is the world?s second largest producer of titanium bearing minerals, but apart from producing titanium mineral concentrate to form TiO2 slag, little further value is added in South Africa to mined minerals. Various studies were undertaken by both government and the private sector in an un-coordinated manner until 2007 when the South African Department of Science and Technology (DST) planned and adopted a national strategy to establish a local titanium metal industry through the research and development of key technologies that would provide a competitive advantage to such a local industry. The strategy entailed a two-pronged approach in the development of this capability, viz. simultaneous investments in the development of high-level human capital and technology in the fields of titanium metal powder production and downstream titanium metal powder processing technologies. To date significant progress has been made to establish research and/or pilot scale facilities in the following technical areas: TiCl4 production technology, titanium powder production technology, high energy milling of titanium powder, metal injection moulding facilities, rapid production of large components using laser additive manufacturing technology, investment casting of titanium, resource efficient machining of titanium and friction stir welding of titanium. Supporting technologies are also at an advanced stage through investments in titanium powder spheroidization and direct rolling of titanium powder. The intent with investment in some of these areas is not to develop new technology per se, but rather to establish local capability that will position South Africa to collaborate with other organisations in the world so that technologies can be acquired and transferred when needed in the future."

Jan 1, 2014

By Felipe Sepulveda, Edelmira Gálvez, Luis Cisternas

"In mineral processing, the recovery and/or concentration of the value components cannot occur in one operational stage, therefore requiring the use of separation circuits based on several flotation stages. The components to be separated are typically distributed at different concentrations and different particle sizes, resulting in different levels of recovery. Typically, more than one value component must be selectively removed by exploiting the differences in the components’ floatability at different pH values, pulp potential and particle size. Several methods for the design of these circuits are available in the literature, but comparatively few studies present circuit analysis tools or address the design of a multiple-product flotation circuit. In this study, global sensitivity analysis was used to analyze a flotation circuit with several products, such as copper, lead and zinc. This analysis was based on the Eureka mine concentrator plant. The analysis was performed for each of the sections of the circuit as an overall evaluation of the circuit. The Sobol’ method and the correlation method were used to evaluate the Eureka mine concentrator plant using the SimLab 2.2 software."

Jan 1, 2014

By A. V. Kanarskay?

The research is aimed at involving in the processing of poor platinummetal natural and technogenic raw materials. The purpose of the research is the creation of a multifactorial complex of innovations in the system of ore preparation and separation cycles, which ensure a high efficiency of flotation enrichment of hard-to-treat raw materials. In the usual practice of enrichment, minerals of the platinum group (PGM) of less than 10 microns in size are the source of inevitable process losses. For poor raw materials, it is precisely thin PGMs that are characteristic, their proportion sometimes being almost 100%, and their opening leads to the formation of a large amount of slime, which adversely affects the efficiency of flotation. To reduce the yield of slimes and increase the selectivity degree of the opening of the PGM in the ore preparation cycle, a dry grinding scheme and pneumoclassification of the milling material has been developed to obtain fractions of different fineness, density and morphology of the particles. From 2 to 5-fold reduction in the yield of slurries for various ores has been achieved. The separation cycle successfully tested are: flotation of fractions in separate cycles with a differentiated choice of the reagent regime; preliminary selective flocculation of slime fraction material; use of a new generation of bioreagents for flocculation and flotation. A new approach to subsoil research is protected by a patent. The dependence of the efficiency of biocollectors on the composition of biomineral extract from the processed raw materials, which forms the basis of new reagents, is established. The possibility of obtaining the degree of extraction of PGM, native gold and sulphides from finely ground pre-fractionated poor ores with the use of biocollectors of at least 85% is proved. With conventional reagents, the extraction of PGM is 12-23% lower, with the use of traditional ore-preparation apparatuses, the PGM recovery rate was halved. Methods for the long-term storage and preparation in industrial conditions of biocollector reagents that do not require the purification of waste waters from them have been developed. The developed multifactorial system of intensification of flotation enrichment can be introduced to recovery PGM from tailings of enrichment of titanomagnetite, chromite and copper-nickel ores.

Jan 1, 2018