Search Documents

By G. Aguilera

It is known that an addition of rigid particles into a fluid medium changes the flow field. Therefore, the rheological behavior of suspensions will be hardly Newtonian, such as their continuum phase. This phenomena was studied by Einstein in 1906 (Einstein, 1956) for the single case of spherical particles in a continuum liquid of a very dilute suspension. The final analysis applied for suspensions was derived from the evaluation of the behavior of ideal gases, finding a simple expression for the viscosity of the dispersion. All the following works about the hydrodynamics of suspensions at low and high solid contents was based in the Einstein´s model. For clay minerals suspensions where the physical and chemical properties of the particles are complex, it was found that the Einstein´s model is not a good approximation, even so for the most dilute dispersions. The present paper shows a new approximation that describes the non-Newtonian behavior of the suspensions of clays, and the attempt of understand how the different fine sizes, shapes and physico-chemical properties of clay particle surfaces give specific characteristics of plasticity, viscosity or visco elasticity to suspensions. Keywords: viscosity, clay minerals, einstein´s model, dilute suspensions

Sep 1, 2012

By A. Prokopiev

The biological stage of reclamation is the third final stage in remediation the damaged mining terrains, which is carried out following the completion of the mining technical stage. The biological stage of reclamation is carried out through restoration of the vegetation layer. The biological reclamation includes all activities related to the introduction into the terrain of vegetation, microorganisms, insects, and animals, with the acceleration of the succession and creating conditions for a sustainable ecosystem close to the natural one. It comprises of all anti erosion and other activities such as the preparation of the land for growing agricultural crops, sowing grass seeds, planting seedlings, amelioration of the soil and further care for the vegetation until its final place on the land. Mineral and organic-mineral ameliorants for biological reclamation were studied. The basic mineral ameliorant is Bulgarian natural zeolites. The zeolitic-rich tuff samples provided from Golobradovo deposit was characterized by their chemical and mineralogical composition and ion exchange properties and X ray analysis. The average content of clinoptilolite was found to be more than 80%. The materials had ion exchange capacity (NH4+) varying from 100 to 110 meq/100g. Chemical modifications of natural clinoptilolites were made in order to form active phases of nitrogen, phosphorus, potassium, and microelements. Slow-acting mineral ameliorant was developed. Organic-zeolite substrate for biological reclamation was developed. This new product is a mechanical mixture of organo-matter and modified zeolites. Agro-chemical parameters of new ameliorants were determined. The substrates including studied overburden dump soil and mineral or organo-mineral ameliorants are produced. The grass growth test was performed. Keywords: biological reclamation, ameliorants, damaged mining terrains

Sep 1, 2012

By Dilip. Makhija, Asim. K. Mukherjee, Tamal Ghosh, Abhay Patra

In India around 15-20% of Run of Mine (ROM) from any iron ore deposit reports to slime dams as byproduct of iron ore beneficiation process. The proportion of iron ore slime to ROM will increase in future with higher proportion of lean grade ores in ROM. Furthermore, tonnages of iron ore slime will also increase with increasing demand of iron concentrate. Presently, this slime is stored in the dam in the absence of beneficiation technology. A beneficiation flowsheet has been developed at Tata Steel. This process produced concentrate of 2.2% alumina with 40 % yield from slime of 7-9% alumina. The iron content in the reject will be less than 40% thus adhering to the regulatory norm. Pilot scale study show waste from slime beneficiation is a good raw material for making a variety of building materials. Waste from slime beneficiation also has soil amendment properties. Pilot scale studies show productivity of rice increased when the waste of slime beneficiation process is mixed with soil. On commercialization of this zero waste technology slime generated from the iron ore washing plant will be completely used. In this paper the result of the pilot scale studies on slime beneficiation and utilization processes towards soil making and making of building materials are discussed in detail.

Jan 1, 2014

By Carlos Pereira, Fábio de São José, Francielle Nogueira

Votorantim Metals Corporation is one of the leader companies in the extraction of zinc in Brazil. One of its mines, located in the city of Vazante - MG, was composed by zinc silicate ores, but recent studies have indicated a change in mineralization type with arise of zinc sulphide’s ore bodies with disseminations of galena (PbS) and silver. The liberation size between sphalerite and galena in this ore occurs in very fine granulometry (approximately 18µm), fact that has negatively influenced into the flotation process. Aiming to reduce this problem, studies about the use of dispersing in the flotation process have started. Thus, this study investigated the action of different reagents dispersing on the stability of the suspensions. The tests were carried out with samples of mineral galena and sphalerite using four types of dispersing within two different dosages and two pH. The reagents tested were sodium hexametaphosphate, sodium silicate, carboxymethiylcellulose, and sodium polyacrylate. The results of the dispersion tests were analysed in relation to dispersion index. The tests with hexametaphosphate showed high dispersion for both galena and sphalerite. The sodium polyacrylate and arboxymethiylcellulose showed a high dispersion index for galena and a low index for sphalerite implying that reagent can be used in the concentration process of galena.

Jan 1, 2014

By M. Naymanbayev

The characteristics of the mineral composition of ores and valuable set of components: the technology of processing depending on the type of mineralization, the nature of the impregnation of ore minerals and their composition have been considered. There have been given technological schemes for processing concrete objects. The analysis of fitness fields for industrial development (degree of scrutiny, the effectiveness of developed enrichment and hydrometallurgy technology) has been provided.

Sep 1, 2012

By Anuttam Patra, Romain Bordes, Andreas Fredriksson, Tommy Karlkvist, Krister Holmberg, Kota Hanumantha Rao

Almost all of the flotation reagents used today were discovered by continued application of empirical methods and/or trial and error experimentation. Moreover, with the metal-ion specific approach used so far, it is difficult to separate the minerals containing the same constituent metal ion. A critical assessment of molecular recognition processes involved in biomineralization suggested the possibility of using reagents which are surface specific. The concept that the molecules consisting of two or more functional groups having appropriate spacing between those so as to achieve structural/stereochemical compatibility during interaction with the mineral surface exhibit structure-specificity is thought to be extended to the design of specific collectors in flotation processes. In the present study, for the first time, a rational design of surface active molecules, and thereby the recognition of crystal faces (of minerals) by these molecules through structural and stereochemical matching is being utilized successfully to selectively float various minerals. For this purpose, carboxylate-based collectors (for mineral specific flotation of calcium minerals) as well as xanthate-based collectors (for mineral specific flotation of sulphide minerals) with a fixed alkyl chain length but having two functional groups with varying geometrical distances (separated by a spacer of one, two and three carbon atoms) between them have been synthesized. In this article, we have discussed the design, synthesis, purification of these novel mineral specific collectors as well as their important solution parameters in relation to flotation processes.

Jan 1, 2014

By G. Belardi, N. Shehu, L. Passeri

"This paper illustrates the possibilities of applying what is essentially a physical soil-washing technique for treatment of soil contaminated by semi-volatile hydrocarbons in order to reduce the level of pollution to that permitted by Italian regulations.The ground around a factory producing lubricating-oil additives consists of silty-sandy soils which have long been contaminated by heavy hydrocarbons, especially branched alkyl benzenes and naphthalene derivatives. Pollution is particularly marked in some zones (hot-spots) where Total Petroleum Hydrocarbon (TPH) values are as high as 7000 ppm. The hydrogeological characterization showed the presence of a gravely soil in a sandy/silty matrix, with big stones making preferential paths to the water circulation. The permeability is 10-5 m/s and the water-table occurs at about 3 m below ground level.After laboratory and pilot-scale studies on representative samples of in-situ soils with TPH between 2700 and 7000 ppm a flow-sheet is proposed for reducing TPH values below the acceptable limits in Italy, namely 700 ppm for hydrocarbons with more than 12 carbon atoms and less than 250 ppm for those with fewer.On the basis of indications provided by laboratory tests a mainly physical treatment process of soil washing has been developed. This is used to clean-up soil from a site polluted by non-volatile hydrocarbons with a high TPH value. The process involves a high-density attrition stage followed by wet screening at 0.5 mm and then wet-gravity separation of the minus 0.5 mm fraction in the centrifugal field.The gravity separation products consist of a light fraction with particle size finer than 15 micron which contains most of the pollutants, and a heavy coarse fraction with TPH values conforming to the limits set by Italian regulations (less than 700 ppm hydrocarbons whose structure contains more than 12 C atoms, and less than 250 ppm of hydrocarbons with less than 12 C atoms)."

Jan 1, 2003

By E. Barsky

"The aim of separation is to obtain two products that are as distinct as possible from each other. It is currently believed that the most objective criteria for the quality of a separation are the Hancock criterion and the entropy criterion.1. Hancock criterion:- for yield of fine product"

Jan 1, 2003

By Aziza A. Yousef, Suzan S. Ibrahim, Mahmoud A. Arafa, Mohamed A. Abdel Khalek

Due to the shortage of fresh water in the Middle East, seawater has been used as an alternative in flotation beneficiation. The flotation process requires about 7 m3 of water/mt ore. This article aims to study the effect of seawater cations and anions on the flotation. Natural pure francolite, calcite, dolomite and quartz were characterized by chemical, thermal and x-ray diffraction analyses, surface area, solubility and zeta potential. Synthetic seawater was prepared with the major chemical composition similar to natural seawater as follow; 2.45% NaCl, 0.52% MgCl2, 0.41% Na2SO4, 0.116% CaCl2 and 0.07% KCl. Also, natural seawater was used in application. The point zero of charge was estimated at pH 6.5, 7.8, 9.2 and 2.2 for francolite, calcite, dolomite and quartz, respectively. Calcium ions were released from the three minerals with Mg2+ and P2O5 3– released from dolomite and phosphate, respectively. The adsorption of collector, zeta-potential and floatability of pure minerals were studied. The effect of individual cations and anions predominant in seawater are studied on individual mineral or group. The troublesome Ca2+ and Mg2+ ions should be controlled by soda ash addition. Sodium silicate improved the selectivity of mineral mixtures and natural ore. At optimum conditions the calcareous phosphate ore yielded a concentrate of 34% P2O5, at 83% recovery with 0.61% MgO, from an ore assaying 25.3% P2O5 and 9.4% MgO. To minimize the Clcontent, fresh water of about 0.5 m3 /t was used and the Cl- decreased to about 0.09 %

Jan 1, 2003

By H. M. Yang

Structural alteration of pyrophyllite during mechanical activation in a planetary mill was investigated by X-ray Diffraction (XRD) and Fourier Transform Infrared Spectroscopy (FTIR) techniques. Mechanochemical effect markedly promotes the decrease in reflection intensities with increasing the grinding time. Prolonged grinding causes the pyrophyllite to become the amorphous structure. It can be indicated that pyrophyllite is very susceptible to alteration by grinding. Crystal size (d006) of pyrophyllite appears to be a limit after 2h grinding. IR spectroscopy analysis shows a little alteration in the bands of pyrophyllite after mechanical activation. The results indicate that the ordered structure of pyrophyllite is destroyed and lattice deformation occurs. Porous silica was then successfully prepared via leaching the mechanically activated pyrophyllite. Pyrophyllite was first ground for 6 h. Ground samples were subsequently leached with 4 M hy-drochloric acid at 80 °C for 2 h to produce porous silica with specific surface area of 188.1 m2/g, total pore volume of 0.18 mL/g and average pore size of 3.9 nm from N2 adsorption analysis. Otherwise, the porous silica obtained from direct leaching of the original pyrophyllite only has a specific surface area of 4.3 m adsorption analysis. 2/g and total pore volume of 0.03 mL/g. It is inferred that grinding is favorable for the formation of microstructure pores. It offers a simple and convenient route for the preparation of porous materials from natural minerals.

Jan 1, 2014

By Nirmal Weerasekara, Malcolm Powell, Mohsen Yahyaei

"The conditions under which rocks become superficially damaged during the grinding process are not well understood. The main purpose of the work presented here is to understand how superficial breakage occurs under incremental low-energy impacts. To enable this study a series of abrasion tests with multi-size pilot mills have been performed. Outcomes of numerical simulation corresponding to each test were examined to investigate the experimental results. Abrasion tests have been conducted using three grinding mill sizes (i.e. 1.8, 1.2, and 0.8 m). Two types of ore were used to investigate different hardness strengths. To ensure abrasion was the dominant mechanism, in all tests the mill speed was reduced to 40% of critical speed. The relationship between the Fractional mass loss rate and particle size was investigated by randomly collecting seven tracer particles from sizes -73+63, -53+45, and -37.5+31.5 mm. It was evident from the results that the Fractional mass loss rate of angular particles declines as the particle size increases whereas the Fractional mass loss rate decreases from fine to coarse in rounded particles. Results of Discrete Element Method (DEM) simulations indicate that fine particles experience higher levels of collision energy per particle and this value reduces as the particle size increases and mill size reduces. This explains the higher Fractional mass loss rate of smaller particles as well as the increase in the Fractional mass loss rate as the mill size increases. Linked DEM and experimental data indicates that under these test conditions surface damage attrition is the dominant mechanism. This work suggests that DEM simulation can be implemented to predict the abrasion wear of particles in mills."

Jan 1, 2014

By Wei Qu, Yongsheng Song, Xingyu Liu, Wenjuan Li, Shuang Liu, Guiying Zhou, Bowei Chen

The Pb,Sb,Zn multi-metal sulphide ore is processed in sequence of beneficiation of jamesonite, sphalerite . Due to relative large amount of collector (xanthate), activator (CuSO4) and regulator (lime) during different flotation stage, the flotation wastewater from sphalerite beneficiation stage can’t be directly recycled to the first lead flotation stage. In this paper, the flotation wastewater from sphalerite beneficiation stage was treated by Ozone and BAC technology, results showed that when the influent concentation of COD and copper ion were 850 mg/L, 10.48mg/L respectively, the Ozone and BAC technology could effectively treat such type of water. In the treated wastewater, the COD is 60mg/L, copper ion concentration is 0.023mg/L, pH is 7.0, which satisfy the need of Pb,Sb-Zn preferential floatation separation process. After recycle of the treated wastewater to Pb,Sb floatation circuit, qualified Pb,Sb concentrate and Zn concentrate were obtained.

Jan 1, 2014

By Chuansheng Luo

If lead-zinc ores have high oxidation rate, separation of lead and zinc is very difficult. This paper studied the technology of preferential flotation by the coarse grinding and re-grinding. The lead concentrate grade is 51.40% and the lead recovery is 62.83% when feed grades Pb 1.74% and Zn 6.46% with oxidation rate being 13.75%. At same time, the zinc concentrate grade is 50.07% and its recovery is 90.01%.

Sep 1, 2012

By A. Buchanan, M. Mirnezami, A. L. Restrepo, J. A. Finch, M. S. Hashemi

Settling rate studies on slurries from Cu/Zn flotation plants occasionally revealed two aggregation maxima at pH 8-10 and 10-12. From measurements on sphalerite and silica suspensions the double maxima were replicated by Zn ions (pH 8-10) and Mg ions (pH 10-12) corresponding to the presence of zinc hydroxide and magnesium hydroxide, respectively. A combination of chemical and electrostatic bridging by the hydroxides is considered to be the aggregation mechanism.

Jan 1, 2003

By Kirsten Corin, Margreth Tadie, Michael Nicol, Cyril O’Connor, Jenny Wiese

"The recovery of base metal sulfides has been emphasized in the study of the flotation of platinum group minerals (PGMs). However, in some ore bodies such as the Platreef of the Bushveld Complex, sulfide minerals do not make up the majority of the more significant PGM mineralization. It is therefore important to develop a fundamental understanding of how non-sulfide and sulfide PGMs respond respectively to the current reagents being used in the flotation of these minerals. The interactions between platinum and palladium sulfides and tellurides with the thiol collectors, ethyl xanthate and diethyl dithiophosphate, have been studied using the electrochemical techniques of mineral rest potential and voltammetry measurements. The differences in the interaction between the two types of minerals with these reagents were of key interest. Rest potential measurements indicated stronger electrochemical interactions of the minerals with ethyl xanthate than diethyl dithiophosphate. These measurements also indicated that there are different forms of oxidized collector present on the mineral surfaces after interaction with ethyl xanthates. Voltammetry measurements support these observations and suggest differences of adsorption on Pt and Pd sulfides than on Pt and Pd tellurides. Voltammetry also showed that there was minimal electrochemical interaction between the Pt and Pd minerals and diethyl dithiophosphate."

Jan 1, 2014

By R. Imhof, S. E. Sánchez-Pino, H. Sprenger, S. A. Sánchez-Baquedano

"In 1992, Ingeniería de Minerales started with the introduction of pneumatic flotation technology in Chile and South America. This technology consists of vertical cells and gyratory cells, used mainly under actual operational conditions, with pilot units directly installed in the concentrator circuits of the industrial process. Successful industrial applications have been observed at Los Pelambres, in the molybdenum plant; at Codelco Andina in the molybdenum plant as pre-rougher to produce directly a final concentrate; in the copper circuit at Las Luces as pre-rougher producing final concentrate using sea water; at Minera Valle Aconcagua where a full automatic plant produces pre-concentrate from fresh tailings as feed; at the silica and silicate reverse flotation circuit of Compañía Minera del Pacífico; in cleaning the final concentrate of Zn by reverse flotation removing ultrafine carbonate; and in a plant that reprocesses fresh tailings from a copper slag flotation process. Positive operational changes in the design of the flotation circuit have been seen in plants using G-cells and V-cells, improving the performance of flotation circuits and the quality of final products. The high concentration of bubbles and micro turbulence produced by the pneumatic aeration units provide a high probability of collision and attachment, reducing dramatically the residence time. Though it is a pneumatic flotation, no compressed air is needed, and the equipment is characterized by low maintenance costs, full automation, savings in investment and energy."

Jan 1, 2014

By T. Laxmi

This paper details the optimization of rougher Wet High Intensity Magnetic Separator (WHIMS) using response surface methodology. The optimization is in parametric form and takes account of the major operating variables in WHIMS operation such as current in ampere and grid gap, in inch. The objective is to recover ilmenite mineral from red sediment deposits of Srikakulam, India by optimizing the rougher WHIMS. We predict mineral recoveries as a function of current and grid gap. Combination of these predictions with assay data provides predictions of mineral grades and recoveries. The optimized response was validated against data derived from laboratory-scale rougher WHIMS test work, comprising (i) mineral grade, (ii) mineral recovery, and (iii) separation efficiency of the process. We observed close match between the experimental and the predicted data over most of the operational range. This paper describes how the optimization was carried out using the response surface methodology along with MATLAB. The response surface was used to closely investigate the separation of ilmenite mineral by varying ampere and grid gap. The results show that under optimum conditions, such as 3.5 amp current (0.53 Tesla) and 2 inch grid gap, the mineral grade could reach, as high as 87.9% in the concentrate with 74.3 % recovery and 74.4% yield. Keywords: red sediment, wet high intensity magnetic separator, optimization, ilmenite, placer heavy minerals

Sep 1, 2012

By V. Tsyplakov

This article reviews factors of preg-robbing effect, occurring in the course of pressure oxidation of ore and concentrates, containing chloride compounds and so-called 'organic carbon'. The article also summarizes the main results of the studies and testwork conducted to overcome this effect. The following efficient preg-robbing mitigation methods have been noted: higher temperature of pressure oxidation process, preliminary removal of natural carbonaceous material from concentrate, chloride removal prior to concentrate pressure oxidation, and addition of water-soluble organic blanking agents, which suppress the adsorption activity of the native ore adsorbents. Keywords: preg-robbing, double-refractory gold concentrates, pyrite, arsenopyrite, blanking agents, pressure oxidation, autoclave leaching

Sep 1, 2012

By L. A. Nemchinova, M. A. Arustamian

"For a long time tailings piles of mining and smelting complexes have met the eye being a prospecting feedstock source for many industries. Nowadays, 6.5 million tons of copper and cooper-zinc processing tailings are stockpiled in the Urals annually, as there is no technology of its processing to provide a full and complex metal extraction within mining and processing operations. In spite of large volumes of mining wastes, not more than 20% of annual overburden, approx. 10% of processing wastes, approx. 40% slags (1) are involved into processing.Based on today’s complex of economic, environmental and social challenges of ore processing, waste processing technology using existing capacities is a burning issue. Mining wastes characteristics (including fine dissemination, variability of physical and chemical properties of mineral surfaces under impact of oxidizing, leaching, etc.) predetermine challenges arising out of its involving into processing and justify high capital intensity of new construction or reconstruction projects followed by replacement of existing processing lines with new ones.In this paper, the authors propose flotation technology for mature tailings of copper, copper-zinc and polymetallic ore processing. The technology developed provides for upgrade of existing process flowsheet diagrams at minimum costs to produce additional saleable products including low-grade copper concentrate, saleable zinc concentrate and gold concentrate thus facilitates sustainable use of depleting minerals and operational efficiency due to cost-efficient processing of already mined materials, being in fact, final semi-products located near existing operations. This is particularly important for operations with standby capacities and not engaged workforce."

Jan 1, 2018

By Kyle P. Flynn, Frank J. Hrach, James D. Bittner

ST Equipment & Technology, LLC (STET) has developed a processing system based on tribo-electrostatic belt separation that provides the mineral processing industry a means to beneficiate fine materials with an entirely dry technology. In contrast to other electrostatic separation processes that are typically limited to particles greater than 75µm in size, the triboelectric belt separator is ideally suited for separation of very fine (<1µm) to moderately coarse (300µm) particles with very high throughput. The high efficiency multi-stage separation through internal charging/recharging and recycle results in far superior separations that can be achieved with a conventional single-stage free-fall tribo-electrostatic separator. The triboelectric belt separator technology has been used to separate a wide range of materials including mixtures of glassy aluminosilicates/carbon, calcite/quartz, talc/magnesite, and barite/quartz. An economic comparison of using the tribo-electrostatic belt separation versus conventional flotation for barite / quartz separation illustrates the advantages of dry processing for minerals.

Jan 1, 2014