Search Documents

By M. E. Holuszko

This paper reports the results of induction time measurements carried out on the products of film flotation of galena and sphalerite particles from three different size fractions (38~75µm; 75~150µm; 150~212µm). As expected, the tailings (sinking fraction) from film flotation at any particular surface tension, had always longer induction times than the concentrates (floating fraction), for both minerals. The difference between the induction times of film flotation concentrate and tailings could be as little as 2.5 ms and 5 ms, and as large as 6 ms and 10 ms. These differences can be related to the different hydrophobic characteristics of these fractions, as expressed by (?c) and composition of the particular film flotation product. In addition, the induction times of the larger particle size fraction were shown to be longer than for the corresponding smaller particle size fraction, even though the average ?c(degree of hydro-phobicity) of these fractions appears to be very similar. Desliming, Cu activation and collector addition to the sphalerite samples was shown to decrease the induction time values significantly.

Jan 1, 2014

By E. R. Bobicki

"Low-grade ultramafic nickel ores, while representing a large potential nickel resource, are difficult to process due to their serpentine content. Microwave treatment is proposed as a technique to improve the beneficiation of ultramafic nickel ores by converting the constituent serpentine to olivine. The present paper reviews the microwave heating response of ultramafic nickel ores and resultant changes in mineralogy, as well as effects on grinding and slurry rheology. Beyond nickel extraction, microwave treatment improves the mineral carbon storage capacity of ultramafic ore tailings, providing a potential source of additional revenue via the sale of carbon credits. The combined positive effects, considered in the context of the whole operation, suggest an economically viable process is possible.INTRODUCTIONAs high-grade deposits become depleted, the processing of low-grade ores has become increasingly important. One such resource is low-grade ultramafic nickel ores. While representing a large source of nickel, these ores are difficult to process due to their serpentine content. Serpentine is a phyllosilicate mineral consisting of 1:1 stacked sheets of silica tetrahedra and magnesium hydroxide octahedra. There are three primary polymorphs: lizardite (platy), antigorite (corrugated) and chrysotile (coiled, fibrous). The anisotropic nature and non-spherical morphology of serpentine particles leads to complex rheology. Suspensions of serpentine minerals, especially those of chrysotile, exhibit high viscosity and yield stress, which can have a negative effect on comminution, flotation and dewatering operations. In flotation, serpentine is known to slime-coat pentlandite, a valuable nickel mineral, and form bubble-fibre aggregates that report to the froth, reducing nickel concentrate grade and recovery. Methods used to counteract the effects of serpentine in processing include desliming, the addition of chemical dispersants, salts or acid, and dilution (Bobicki et al., 2014a). Microwave pre-treatment has been proposed as an alternative way to eliminate the deleterious effects of serpentine in ultramafic nickel ore processing by converting the serpentine to olivine via dehydroxylation, which occurs at 600-700oC (Reaction 1). Olivine is isotropic, consisting of isolated silica tetrahedra linked by octahedrally coordinated magnesium ions, and has the same surface potential as pentlandite at the pH of flotation (~pH 9). Furthermore, since olivine is more reactive to CO2 than serpentine, microwave pre-treatment creates an opportunity to store more CO2 in tailings, an attractive option for mining operations looking to increase their bottom line where carbon pricing exists."

Jan 1, 2018

By Yuhua Wang, Huilan Yang, Yanqing Jiang, Dongfang Lu

"Generally, the concentration of bauxite flotation tailings is around 10%, a large amount of water in tailings needed to be recycled in the flotation process. Sedimentation and dewatering properties of tailings were investigated under different conditions. Surface high negative charges on mineral particles are the key factor to destroy the settlement of tailings when the pulp pH is around 8.9. Hence, the modification of pulp pH around 7 is necessary to the diminution of the repulsive force between mineral particles and then the acceleration of sedimentation of tailings. Anionic polyacrylamine with molecular weight of 14 million is the best flocculant for the settlement of tailings in all tested polyacrylamines. P-toluene sulfonic acid shows better properties than hydrochloric acid for pulp pH adjustment when anionic polyacrylamine with molecular weight of 14 million is used as flocculant. Although the flotation of diaspore is depressed in the presence of polyacrylamine using sodium oleate as collector, but the recycling water traded by the combination of ployacrylamine and p-touenesulfonic acid does not show the depression effects on the flotation of bauxite ore. The lower residual content of polyacrylamine in recycling water treated by the combination of ployacrylamine and p-touene sulfonic acid plays an important role. INTRODUCTION Generally, the waste water generated from mineral processing plant is usually treated by sedimentation, oxidization, electrodialysis, ions exchange, active carbon adsorption and flotation technology, and the treated water is also used again in the industrial process. Flotation was adopted widely to improve the quality of bauxite from low grade diasporic bauxite in China. For flotation, the grinding fineness of bauxite is over 90% -0.074 mm, sodium carbonate and sodium hexametaphosphate were used as regulators, so the tailings pulp is very difficult to settle and be dewatered (Y. Wang et al., 2004; Y. H. Wang et al., 2007; Wang Yu-hua et al., 2008; Wang Yuhua et al., 2011). The water recycling of bauxite tailings are becoming the highlight for the industrial application of the flotation process for bauxite ore. Researchers in China shift their attentions onto this topic."

Jan 1, 2018

By I. Nishkov, I. Grigorova, M. Ranchev, S. Dzhamyarov

"Chelopech concentrator (part of Dundee Precious Metals) is located in central-western Bulgaria. The current process plant utilizes conventional primary crushing and SAG mill grinding, copper and pyrite rougher and cleaner flotation stages to produce a marketable gold-rich copper and pyrite concentrates. As in the most processing plants, the pyrite depression is carried out alkaline media using lime. The subsequent activation of pyrite mineral is achieved by adding sulfuric acid, which has an adverse effect on the flotation equipment. Therefore, a series of laboratory flotation experiment for activation of lime depressed pyrite by ammonium salts, such as ammonium chloride (NH4Cl), ammonium sulfate (NH4)2SO4 and ammonium bicarbonate (NH4HCO3), have been conducted. The obtained results showed that ammonium bicarbonate proved to be the most appropriate reagent choice for pyrite mineral activation. These results are confirmed by X-ray photoelectron spectroscopy (XPS), performed to determine the surface chemistry of pyrite in its natural state, after lime treatment and subsequent treatment by NH4HCO3. The registered XPS spectra indicate that the hydrophilic phases on the pyrite surface could be efficiently removed by using the ammonium salt NH4HCO3. The industrial use of NH4HCO3 as an activator of lime-depressed pyrite is a possible alternative for sulfuric acid replacement as a most widely used pyrite activator. Flotation experiments with addition of 200, 400, 600 and 800 g/t from each of the studied ammonium salts have been conducted. Furthermore, the impact of the flotation pulp pH within the scope of 9.00 – 10.50 was also investigated. The obtained results from the laboratory flotation experiments, showed that the pyrite activation with ammonium bicarbonate is an excellent possibility for replacing the sulfuric acid as main pyrite activator reagent, in order to eliminate the gypsum accumulation during the flotation of pyrite in Chelopech concentrator.INTRODUCTION The Chelopech deposit, located about 60 km east of Sofia is one of the largest Cu-Au deposits in Europe. The ore have complicated mineralogical and chemical composition. The main ore minerals are represented by pyrite, enargite (luzonite), tennantite, chalcopyrite and bornite. The average copper content of the mined ore is about 1.1 % and the gold content is about 4.0 g/t."

Jan 1, 2018

By H. Araneda

Throughout Chile?s history, mining has consistently been a leading industry in the country. The 1990s marked the beginning of a boom in Chile?s mining industry, especially in copper mining, due to both foreign and local direct investment in the sector. Mining?s contribution to the GDP was 15.6% at current prices in 2009, and it accounts for 56% of the country?s exports. Chile?s copper market share reached 35% in 2009. The investment portfolio in mining in Chile for the coming decade has been estimated at 90 billion US dollars. The acute scarcity of human resources currently experienced by the mining sector in Chile will be accentuated in the coming decade as a result of this scenario of investments. The situation is, additionally, similar to the one confronted by other countries involved in the mining industry such as Australia, South Africa, Canada, and in Latin America includes, Peru, Colombia and Brazil. A study carried out by Fundacion Chile, ¨Labor Force in the Chile Mining Industry, Diagnostic and Recommendations, 2011-2020? shows the projected labor shortage for the operation of projects in the development stage, considering only the requirements of the process of extraction, processing, and maintenance. The demand, accumulated incrementally, will be around 115,000 technically skilled workers, professionals, and qualified workers. This figure refers to the operational work force, and does not include the human resources that will be required for the prior stage of the engineering and construction of the projects (brownfield and greenfield). The demand for technically skilled workers and professions for the stages of engineering and construction of the projects that have already received investments is estimated to be 190,000 people for the period 2012-2020. The peak of the demand for engineering is 2012, with a figure that surpasses the 12,000 professionals for all of the engineering specialties. The analysis of the formation of human resources at the tertiary level (where tertiary includes technical/vocational and academic degrees at the undergraduate level) for mining and related majors demonstrates that the programs are scarce with a bias toward theoretical contents and that they are excessively long (40% longer than comparable programs in Australia, Canada, and in OECD countries). The completion rates are low, especially in the technical-vocational programs, which have a completion rate of only around 30%. Finally, the rates of attraction of technically skilled labor and professionals towards careers in mining are insufficient to reduce the identified skill gaps. In the case of university professionals such as geologists, mining engineers and engineers in metallurgy, 80-90% will work in mining. In the case of graduates of relevant majors, that cover skills also utilized by other industries, not only mining?such as maintenance workers, operators of fixed and mobile equipment, etc.?the mining sector appears to be unattractive for reasons such as shift schedules, geographical location of work sites, and other factors. On the basis of the available diagnosis a strategy for the sector has been developed (Workforce Development and Skills Strategy) whose objective is (i) to define a Mining Qualifications Framework to identify the critical roles to be filled (ii) to start, with public resources, a ¨fast-track? training program to assure the availability of at least 28,000 operators (machinery operators, truck drivers, etc.) and maintenance specialists in 2015 (iii) to promote the development of training hubs for mining with learning technologies to train technical labor and professionals on the basis of world class standards (iv) to design and implement a campaign oriented toward the perception of mining as an attractive field of employment opportunity (v) to develop curricular innovations for tertiary education programs, on the basis of international benchmarks. Keynotes: Chile, mining, copper mining, skilled human resources

Sep 1, 2012

By N. Naudé

The theory on particles displacement subjected to upwards and settling movements in water, using a water pulse, is described in literature, but very little experimental data is available to verify these theoretical ideas. The aim of this research work was to visualize the displacement of solid particles in a mixture of water and solid particles created with the aid of water pulses in the Mineral Density Separator. From the literature it is known that lighter particles are subjected to higher levels of displacement than heavier particles, and when the particles then settled down, layers of material are formed ac-cording to the densities of the material. By removing the individual material layers, the materials can then be separated according to their densities. During this study the individual material layers were investigated regarding the density and size distribution in that specific density layer. It is important for this project to have a statistical prediction of the ?real? flow of the particles with different density and size distribution, inside the Mineral Density Separator. The information gathered during this study will be used to show the correlation between a two dimensional model of the particle flow and that of the real three dimensional flow inside the Mineral Density Separator.

Jan 1, 2014

By V. G. Prikhodko, G. I. Sukhinin, I. V. Yarygin, A. V. Fedoseev, S. A. Novopashin

"The first experiments on the vacuum drying of spherical clay sample are presented and the theoretical model of the process is considered. The model is based on the solution of the heat and the moisture transfer equations with the effective thermal conductivity and water diffusion coefficients for wet porous clay-like medium. The time and radial dependence of the temperature and the moisture were calculated for different initial conditions. The results obtained for the time dependence of the moisture content are in good agreement with the experimental results obtained in the initial period, when all the moisture in the sample did not freeze to form an ice crust. INTRODUCTION Capillary-porous materials very often occur in nature and in industry. A porous medium is a solid matrix with voids, or pores, which are continuously connected. These pores are usually filled with fluids or moisture, water vapor and air that can pass through the medium because the voids are interconnected. The void fraction in the solid matrix is referred to as the porosity. Porosity or void fraction is a measure of the void (i.e. ""empty"") spaces in a material, and is a fraction of the volume of voids over the total volume. The moisture content in porous media determines the properties of the porous body, its mechanical and thermo-physical properties, such as density, plasticity, viscoelasticity, swelling, cracking, and so on. Complex processes of heat and mass transfer occur in porous bodies when they are heated or cooled, during drying or freezing (Luikov,1966). The course of these processes depends essentially on the physical-chemical composition of the solid matrix of the porous body, on its fractal dimension, porosity and morphology. The clay and clay minerals are the most important porous materials in the history of the mankind (Mukherjee, 2013). Clay is a very fine grained, unconsolidated rock matter, which is plastic when wet, but becomes hard and stony when heated. It has its origin in natural processes, mostly complex weathering, transported and deposited by sedimentation within geological periods. Clay is composed of silica {SiO2), Alumina (Al2O3) and water (H2O) plus appreciable concentrations of oxides of iron, alkali and alkaline earth, and contains groups of crystalline substances such as quartz, feldspar, and mica. Building materials, bricks, and tiles, pottery, porcelain and faience are made from clay. Clay is used in the food and medical industry, and, not least, in the mining industry as a carrier containing aluminum, silicon and other valuable elements, as well as metals (copper, gold) as constituents, contained in the pores in the form of micro- and nano-particles or grains."

Jan 1, 2018

Three high-grade limestone ores (CaO content over than 53 %) with different geological origin have been characterized for the synthesis of aragonite precipitated calcium carbonate. Limestone ores examined in this study showed different crystal particle size that cause difference in disintegration degree and surface area of the synthesized slaked limes. The limestone ore with smaller crystal particle size showed higher disintegration degree and also yielded slaked lime with smaller surface area, which is good for the synthesis of aragonite precipitated calcium carbonate. The synthesis of aragonite PCC using the limestone with a small crystal particle size was yielded needle-shaped aragonite with the aspect ratio of about 14. Keywords: limestone, lime, slaked lime, precipitated calcium carbonate, aragonite, accelerated carbonation

Sep 1, 2012

By Fedotov Pavel

One of the efficient means of ore disintegration during the processing is its volume breakage in such machines as roller-presses. Up to date neither the ore disintegration mechanism in roller-presses nor the reasons of their high efficiency are thoroughly investigated. In this work, the mathematical model of Finite Element Method of bad material disintegration in roller-press is discussed. The mechanism of the interparticle ore disintegration is traced.

Sep 1, 2012

By Sashnee Raja, Mehdi Nemati, Ashley Sissing, Susan T. L. Harrison

"Extreme thermophiles, operating at 65 - 90°C, are finding increasing application in biohydrometallurgy These microorganisms have the advantage of exhibiting better oxidation kinetics in terms of reaction rate and extent of mineral solubilisation. These extreme thermophiles are Archae, characterised by a different cell envelope structure perceived to provide reduced structural strength in comparison to bacterial envelopes, and customised metabolic pathways.The active tank bioleaching process, used for high rate leaching, is conducted in a slurry bioreactor. Here sufficient energy dissipation is required to ensure suspension of the mineral phase as well as to sustain high rates of gas liquid mass transfer. It is well known that subjection to hydrodynamic stress of sufficient magnitude may alter the physiological state of a range of micro-organisms through changed viability (ability of the microbes to grow), metabolic activity and integrity.In this paper, we report on studies carried out to quantify the ability of the extreme thermophile Sulfolobus to withstand the hydrodynamic stress environment generated at high pulp densities in the slurry bioreactor. Both a pyrite system (as a model system) and a chalcopyrite system (as an application) were studied. In laboratory reactor systems, the nature of biological responses to stress induced at high pulp density have been identified in terms of ability of the microbes to grow, their metabolic activity and rate of leaching and cell integrity. Critical operating conditions within the laboratory reactor are identified and the mechanism mediating reduced performance considered."

Jan 1, 2003

By B. McFadzean, P. E. Ngoepe, P. P. Mkhonto

"The theoretical technique of computational modeling and the experimental determination of the enthalpy of adsorption of a ligand molecule onto a mineral surface deliver the same output parameters and, therefore, complement each other in investigating the affinity of different ligand types for mineral surfaces.This study ran parallel experimental tests and computational calculations to determine the enthalpy of adsorption of a series of increasing chain length xanthates onto a pyrite surface. The outcomes showed that, while the absolute energy values were different, the trends were similar. Both computational and experimental approaches showed that the extent of the interaction of the xanthate molecule increases with increasing carbon chain length. The computational values were larger than the experimental values, which could be explained, in part, by the addition of water to the computational system, which resulted in a decrease in the heat of adsorption on the (100) surface, compared to the adsorption of the collector in a vacuum. The computational method showed that, in the case of the pyrite (100) surface, the most exothermic reaction was obtained when the two xanthate sulfur atoms bridged two pyrite 5-coordinated iron atoms. The (111) surface was found to be more reactive and different adsorption mechanisms were predicted for each of the C2, C3, C4 and C5 chain length xanthates.The experimentally determined exothermic increase in heat of adsorption for the addition of each CH2 group was found to be -8.17 kJ/mol. The contribution of the thiol head group was -34.9 kJ/mol. Previous studies on self-assembled monolayers have shown that these values are compatible with lateral interactions between CH2 groups and the exclusion of water. This study provides a rigorous experimental and computational approach which is intended to afford confidence in modelled data for the screening of new ligands for flotation processes.INTRODUCTIONComputational modelling is a fast and cost-effective method of screening collector molecules for the efficacy of their adsorption onto mineral surfaces. However, it is desirable to measure the computational outputs against experimental outputs to check for congruency. Computational modelling and experimental microcalorimetry both deliver the same output parameter: the energy of adsorption of the molecule onto the solid surface. These techniques are therefore ideally suited to complement one another in investigating the affinity of the interaction between collector molecules and mineral surfaces."

Jan 1, 2018

By Jacek Kolacz

A new sensor based sorting system has been developed, based on complex image analysis, where an image texture and a shape pattern is considered for identifying particles for separation. The sorting system employs different images generated by visual light and X-ray to provide maximal information about processed particles. Application of X-ray makes it possible to analyse the internal structure of the particles, which provides a 2D image with complicated texture, however, which contains valuable information. The advanced system for the texture and the pattern recognition is applied to analyse these images simultaneously, to provide the required identification of the particles for efficient separation. The mathematical models applied during identification and separation, are assisted by high speed calculations being specially optimised for this kind of process. This allows sorting with high capacity and high accuracy, which is critical for practical applications in mineral processing. The paper describes a number of tests during sorting of iron ore and coal with high separation efficiency.

Jan 1, 2014

By A. Sand

Within stamp-charged coke making a large volume of coal is compacted to one single coal cake before entering the coke oven chamber. This is done by means of several falling stampers in a stamping machine having a mold nearly of the oven?s dimensions. Producing a high quality coke also from inferior coals requires a cake density of approximately 80% of the coal density. Besides that the industrial stamp-charging process demands a minimum mechanical strength of the coal cake to move it from the stamping mold into the oven chamber without failure. Densification and the build-up of cake strength were investigated earlier in stamping tests using a micro-stamping device. The quantities derived from these tests (as e.g. cake density or porosity) represent average values for the entire cake. Statements describing the local compaction state at different heights are difficult to achieve without destructing the cake. In order to gain better insight into the densification process and the inner structure of the coal cake a computational model based on the discrete element method (DEM) has been set up using 2 and also 3-dimensional simulation software. The stamper?s position and velocity as well as the force acting on the stamper were monitored and the model?s response was compared against measurement data from laboratory stamping tests. It was possible to reproduce the force and displacement pattern of the stamper in response to the viscoelastic properties of the cake using standard DEM bonding and contact models. Furthermore, the rearrangement of particles in response to the compaction by the stamper was tracked by calculating their displacement at the point the stamper hit the coal surface. The latter can also be used as indicators of particle deformation or breakage. By defining control points at different heights the particle displacement, stress and strain rates, porosity could be studied at different heights. Keywords: coke making, coal stamping, compaction, agglomeration, DEM, simulation

Sep 1, 2012

By S. Gaydardzhiev

Laboratory batch tests having preliminary and orientation character aiming at improvement of the molybdenum flotation at Ellatzite copper processing plant in Bulgaria have been conducted. The following technological parameters have been screened to study their influence on the grade and recovery of copper and molybdenum during the rougher flotation stage: flotation pulp density, pH, addition of secondary collector and replacement of MIBC by pine oil as a frother. The results have shown that slightly better grade/recovery figures could be obtained for both copper and molybdenum at lower flotation pulp densities. The addition of kerosene has improved the recovery of molybdenum however, on the expense of that of copper. The effects from pH variation and the replacement of MIBC by pine oil as a frother have been almost negligible.

Sep 1, 2012

By Pan, Jian, Siwei Li, Deqing Zhu

"It is great significance to realize the efficiently and comprehensively utilization of iron, manganese and aluminum from refractory high-aluminum and high-manganese iron ores. Aimed at the two types of low grade refractory iron ores, mineralogical characteristics were studied. The direct reduction behaviors and evolution of mineral compositions of single iron ores and their blended ones were analyzed, and the corresponding reduction mechanisms were demonstrated. The results showed that only a part of iron oxides in high-aluminum ore are transformed to metallic iron after reduction, while the other react with aluminum and silica to form fayalite and hercynite which are difficult to be reduced. For the high manganese iron ore, most iron oxides can be reduced to metallic iron and manganese oxides can combined with aluminum-silica minerals to form galaxite and tephroite, promoting the reduction of iron oxides. Co-reduction results demonstrate that reduction of high- aluminum ore can be promoted by adding with high-manganese ore. Metallization and metallic iron grains increase dramatically by elevate high-manganese blending ratio. At the ratio of 60% high- manganese iron ore in the pellet feed, iron-slag separate well with a slag assaying 28.51%~36.35% Al2O3 and the recovery of iron and manganese can be reached 93%, respectively. The high-aluminum rich manganese residue was recycled with H2SO4. INTRODUCTION The growth of the Chinese iron and steel industry has been pushed forward by its rapid economic development in recent years, and 1126 million tons of iron ore have been consumed in 2014, where 933 million tons were imported according to the data from World Steel Association [1]. However, iron resources are limited, and especially the reserves of high-grade iron ores are declining, so it is of significant importance to optimize the mining rate of iron resources [2] and to utilize low- grade refractory iron resources, such as high-aluminum iron ore."

Jan 1, 2018

By H. Z. Kuyumcu

Coking of coal blends using high volatile coals with poor coking abilities to produce a high quality coke for blast furnace application can be achieved by compacting the coal blend prior to the carbonization process. Here densification up to a relative material density of 80 %, i.e. a compact density around 1100 kg/m3, has proven to be advantageous. Coal is compacted by stamping, if the so-called stamp charging process applied. Compacting of the coal by pressing is practised in case of the cokemaking with so-called heat-recovery ovens. Stamped and pressed coal cakes require over the cake volume uniform high density and mechanical stability. Besides the aspects of the coal selection, the efficiency of the process is mainly determined by the operating parameters compacting time and compacting energy for coal cake making. At the Department for Mechanical Process Engineering & Solids Processing of the Technical University Berlin the two sub-processes of densification and strengthening during stamping and during pressing are theoretically and experimentally investigated using specially developed lab-scale compacting test units and a strength test device. Describing cake density in terms of coal properties for a given coal and measured compacting energy input then leads to a compacting equation with the so-called Stampability as the integral model parameter for the stamping process. For the pressing process the cake density can be calculated with the measured compacting pressure and the Compressibility factor, respectively. Investigations were carried out to provide evidence of a significant influence of coal type, coal surface moisture, coal granulometric and mechanical properties on the densification process. The overall objective of the work is to establish a comprehensive mathematical model on the compacting behavior of large coal bulk quantities and the optimization of the compacting processes by stamping and by pressing. Keywords: coal compacting, agglomeration, stamping, pressing, cokemaking

Sep 1, 2012

By A. I. Urvanzev, N. V. Shikhov

"In this paper, we present the study’s results of electrical separation processes on the basis of new separator designs, new technological solutions, and newly discovered effects. We considered the options of enrichment by magnet separation of magnetite and titanomagnetite ores, ores and products containing chromium and manganese, ores of non-ferrous and precious metals. During pneumo-electric separation of mixed iron ore of SMPC, 43.3% of the output of the concentrate with an iron content of 61.7% was obtained in one step, with extraction of 70.5%. The paper also presents the results of the finalization on the air-electric separator of the magnetic fraction when separating oxidized ores of MPPOO (mining and processing plant of oxidized ores) on the Jans polygrade magnetic separator. A concentrate was obtained with an iron content of 65.1% with the extraction of 95.0% and tails with an iron content of 13.0%. The possibility of obtaining low-silica concentrates from these ores with an iron content of 67.15 and a quartz of 2.88% is shown. Also, the results of tests on the enrichment of chromite ores on the firing-magnetic scheme with corona-electrostatic separation are considered. On the initial ore of the Don MPP (mining and processing plant), a concentrate with a content of 61.8% Cr2O3 was obtained with a quartz content of ~ 1.0%. The results of pneumo-electric separation with triboelectric charge of the separated particles are presented. The results of the tests indicate a principal possibility of enriching chromite ores without costly high-temperature roasting. Dry technology of enrichment of manganese ores with the use of electrical separation increases the quality of the oxidized concentrate to the first grade and raises the total extraction by 2 times. For the Chineya deposit of titanomagnetite ores with copper impurities, electroseparation operations were carried out on two samples with a Cu content of 1.93 and 3.75%, respectively. For a sample with a Cu content of 6.02%, a copper concentrate output of 24.42% was obtained with a Cu content of 23.82% and the extraction of 94.88%. The results of enrichment by electroseparation of gold-containing sulfide ores can have the practical importance. For ores of the Berezovskoye deposit, a pyritic concentrate containing 100 g / t of gold was obtained after two or three operations of IES (integrated energy systems)."

Jan 1, 2018

By M. Saghaeian, R. Hejazi, M. Mohammadinejad, M. Zare

"Water quality and quantity at the Tailing Thickening Section of processing plants is considered to be a crucial factor and impacts the performance of several sections. Therefore, gaining stable and effective performance at the Tailing Thickener Section is one of the principal goals of minerals processing plants. Different factors such as: qualitative and quantitative sustainability of plant feed, the balance between the mass of input and output water flow, the dissolving method and distribution of flocculant and the amount of dirt, solid percent of thickener inlet pulp, affect the performance of Tailing Thickener. The present study investigates the successful improvement of Tailing Thickener performance at Jalal Abad Hematite Iron Ore Concentrate plant through optimizing the above operational parameters. For this purpose, the following optimizations have been done: homogeneity and sustainability of plant input feed rates, fine pulp removal collected by the bag filters at the input of the thickener, adding an quietness box before moving the tail pulp into the thickener to reduce the pulp turbulence, replacing flocculant pump and injection pipes, improving water mass balance which leads to optimizing and stabilizing the concentration of input tail pulp into the thickener, adding a mixer to increase the flocculant preparation time, increasing the locations for adding flocculant to thickener from 1 point to 6 points. Applying the above modifications and monitoring the Tailing Thickener performance over the course of months, has led to the improvement of recovered water quality from 500 ppm to 200 ppm, increasing the solid underflow of the thickener from 40% to 48.5%, and similarly, reducing water loss by 60%. Of other important effects, due to improvement of water quality, grade of final concentrate 0.5% increased and because of 73% increase in monthly working hour, concentrate tonnage 55% increased. Finally, sludge thickener optimization has had a significant effect in selecting and designing the dewatering system from the underflow of the sludge thickener."

Jan 1, 2018

By P. Han

The preparation technological conditions and regeneration method of two novel granulated adsorbing materials of rectorite/fly ash composite (Material 1) and rectorite/water quenched - slag composite (Material 2) and the use of them to remove heavy metals from copper smelting plant wastewater have been studied. The experimental results showed that under the preparation conditions with the ratio of rectorite to fly ash or water - quenched slag of 1:1, the amount of the additive (Industrial Starch, IS) of 15% (Material 1) or 10% (Material 2), the addition of 50% water, and the calcination temperature of 500? (Material 1) or 400? (Material 2), the efficiency of heavy metal removal with the granulated materials was the best, whereas the ratio of disintegration loss was the lowest. Under the treatment conditions of natural pH, and with the addition of the granulated materials of 0.07g/cm3 (Material 1) or 0.05g/cm3 (Material 2), a reaction time of 60 minutes (Material 1) or 40 minutes (Material 2), and the adsorption temperature of 25?, the efficiency for the granulated materials to remove Cu2+Pb2+Zn2+Cd2+ and Ni2+ from the copper smelting plant wastewater was 98.9, 97.5, 96.7, 90.2, and 79.1, (Material 1) or 98.2, 96.3, 78.6, 86.2, and 64.2, (Material 2), respectively, and the quality indexes of the wastewater after treatment conformed with the first level of integrated wastewater discharge standard (GB8978-1996). When the adsorption of heavy metal ions on the surface attained saturation the granulated materials could be regenerated by washing with 1 mol/L sodium chloride (NaCl) solution and still with quite good heavy metal removal efficiency. The granulated adsorbing materials had the advantages of high efficiency of wastewater treatment, easy method of solid-liquid separation and regeneration, and a broad prospect of applications.

Jan 1, 2014

By V. Hema

Granular materials are widely used in process industries, such as chemical, pharmaceutical, cement, food, detergents, and fertilizers. Mixing, blending, calcining, reduction, heating, and granulation of these materials are frequently carried out in rotating cylinders. In all of these processes, the mixing and segregation of these granular materials is important as this controls the secondary phenomena in the rotating kiln such as heat transfer to the material. A significant amount of work is available in the literature but to date these efforts have not been able to capture the important parameters affecting the mixing and segregation in rotating kilns. In addition, the range of parameter values studied so far is rather limited. Simulations of granular materials are based on either discrete elements or continuum models. The discrete element methods (DEM) combine semi-empirical models for the inter particle interactions with the equations of motion from classical mechanics to simulate the explicit paths of all granules in a rotary kiln, thus yielding realistic predictions of the mixing process. This approach is very demanding computationally, which strongly limits the number of granules and the number of revolutions in a simulation. Continuum models dispense with the discrete particles and can therefore be scaled up more easily. But the constitutive relations that serve as the foundation for continuum modeling are difficult to come by, and often only applicable to specific systems and conditions. Here we have chosen DEM simulation for investigating the mixing and segregation behavior of granular materials in a rotating cylinder. This work is directed towards demonstrating the capability of the prediction of the mixing and segregation behavior of granular materials in a horizontal rotating cylinder through discrete element simulation. Further the effect of particle size and rotational velocity on the mixing and segregation behavior is investigated. The simulation results are quantified in terms of mixing index, mixing rate, segregation index and percolation index. Keywords: DEM simulation, granular mixing

Sep 1, 2012