Search Documents

By T. A. Penzov

As a result of recent scientific and experimental studies new technical devices have been developed for monitoring and control the process of grinding. The description of microprocessor module MILLCONT 1 for control of the loading of the mill and microprocessor density control module DENSIMETER is given in the paper. The improved variant of the automatic system for ore grinding control in single-stage ball mill working in close cycle with a classifier with above mentioned technical means is shown in the paper. The loops for measuring and stabilization of the basic technological parameters (density of the ready pulp ? and fineness of grinding of the pulp ß) are described in the paper. The nowadays economic results in ore grinding process automation are given as well.

Jan 1, 2014

By Y. Y. Li, Q. Chen, Y. X. Cai, Q. Zhang, S. Mao

"Due to the influence of combustion conditions, the fly ash produced by some power plants has the problem of high-carbon content. The unburned carbon in fly ash can be removed by flotation, and the decarbon tailings should reach the national standard level I fly ash. The fineness of the requirement is one of the important indicators and is also an important factor affecting the tail ash activity. In this paper,adopting two methods investigate the effect of particle size on the flotation index: one is direct flotation of fly ash, and the other way is wet grinding + flotation of fly ash, comparing the two methods and selecting the appropriate process,which provides a way for the effective utilization of fly ash. INTRODUCTION Fly ash is a solid waste discharged from coal-fired power plants. The annual amount of emissions of fly ash are very large in China. The amount of fly ash were discharged from coal-fired power plants are increasing gradually, and the amount of fly ash stored has exceeded 2.5 billion tons, but the comprehensive utilization of fly ash is not high, which brings about a huge environmental problems( Lu et al.,2011). Carbon is a harmful component of fly ash in cement and concrete application (Zhang et al.,2008). Fly ash decarburization is an essential link to improve the utilization efficiency of fly ash and the reduce pollution ( Yang et al.,2012). Carbon is selected from fly ash to make full use of fly ash resources and improve utilization of fly ash (Li et al.,2008). In this paper, the flotation decarburization of high-carbon fly ash is studied, through comparing the grinding and not-grinding processes, optimizing the separation process of fly ash, which provides a way for the effective utilization of fly ash."

Jan 1, 2018

By X. Y. Liu

A culture-independent approach based on 16S rRNA gene clone library was used to analyze the bacterial community change both associated to the solids and in the liquid phase during pyrite bioleaching process. Phylogenetic analyses of 16S rRNA fragments revealed that the retrieved se-quences mainly related to genus Leptospirillum, genus Sulfobacillus and genus Acidithiobacillus. During the bioleaching process, genus Leptospirillum trends to grow associated to the solids while major of genus Sulfobacillus were in the liquid fase, only accounting little portion in the solids. Genus Acidithiobacillus can grow both on the solids and in the liquid phase, but accounting high portion on the solids.

Jan 1, 2014

By Bertil I. Pålsson

The most common REE containing mineral that is worked today is bastnäsite. It means that mineral processes are adapted to it and that the metallurgical separation techniques for winning of individual REE are adapted to bastnäsite concentrates. For all other deposit types, suitable mineral processing methods and separation technologies need to be adapted and/or developed. Preliminary mineralogical analyses indicate that slightly less than half of the REE in the tailings dumps at LKAB/Kiruna are associated to apatite. The rest is in the minerals monazite (maybe associated to apatite) and allanite. At least allanite is probably not floatable with reagents commonly used for apatite. Mass and element distributions for the tailings sand reveal that very little apatite is present above 300 µm, and that approx. 30 % is below 20 µm. REE does not follow P2O5 completely and are also present in coarser fractions. Flotation results show that the best condition for both apatite and REE winning is pH 9, high collector addition and low dosage of water glass. Under these conditions, the lab-scale flotation gives an apatite concentrate with at least 30 % P2O5 at 70 % recovery. REE follows apatite in the cleaner steps but only partly. Its recovery is approx. half compared with apatite. The reason for the low REE recovery is likely to be that REE to a large extent is trapped in non-winnable minerals, especially allanite. The REE grades in the concentrate are expected to be in the range 3000 ? 4500 g/ton. Keywords: flotation, REE, apatite, monazite, allanite

Sep 1, 2012

There are interactions between different minerals from the same ore, minerals and grinding media, and the electrochemical conditions present in the system. Grinding in steel rod and ball mills is a common practice in minerals processing. It is accepted, that the electrochemical interactions between the grinding media and minerals in a grinding mill, influence the corrosive wear of balls/rods and the surface properties of the ground minerals. A complex massive sulphide, Cu-Zn, TAKNAR, Iran, was used for all the experiments. The aim of this study was to investigate the effect of grinding media (dry or wet) on the pulp chemistry and recovery of Cu and Zn in bulk concentrate. 1100 g of ore samples were milled, and mill products with d80=85 and 75 micron in wet and dry grinding methods were produced. Rougher bulk flotation experiments were performed with 550g ore samples, at 30% solids. SIPX in conjunction with Aero238 in 1:2 ratio (48 g/t), was used as mixed collector system, and copper sulphate (200g/t) and MIBC (20 g/t) were employed as sphalerite activator and frother. Lime and High purity Oxygen gas were used for adjusting pH at 8.5 and aeration. The results showed that, more positive pulp potentials were measured when the feed had been ground in a dry environment, and the difference in pulp potentials between the dry and wet ground feed was approximately 250 mV after the grinding stage. In dry grinding method, the recovery of Cu and Zn increased approximately 5 and 10%, respectively. In addition, in dry ground samples, the volume of middling and coarse particles (+100 micron) were more and Dry ground flotation feed had better agreed with using a mixture of collectors. After using copper sulphate, pulp potential increased about 50 mV in dry and 75 mV in wet grinding methods. Keywords: grinding media, pulp potential, Cu-Zn massive sulphide, bulk flotation

Sep 1, 2012

By A. F. Usov

A potential of electric pulse disintegration in benification used for primary deposits ores containing precious metals is shown. Of special significance is that PGM and gold grains, being highly plastic, are easily liberated and are not smeared on the disintegrated rock fragments surface. It al-lows gravity separation, which is less expensive and more efficient, to be used instead of chemical processing, which is expensive and environmentally faulty.

Jan 1, 2014

By M. H. Moys, M. M. Bwalya

The use of the Discrete Element Method (DEM) to simulate the interaction of particles in dynamic environments is growing rapidly. This technique is also being applied in the study of milling extensively. However, to date more focus has been on the validation of the model. In spite of the advantages of the detailed information that is available from the simulator, appropriate application of this information remains a daunting task. In this paper a technique that combines particle breakage probability data with the energy spectra generated from the DEM is discussed.

Jan 1, 2003

By A. Saramak

"The paper focuses on problems of atmospheric pollution by the dusts, produced during the course of crushing and grinding processes, and the main objective of investigative programme is an assessment of emission of particulate pollutants for following crushing devices operated in plant scale: impactors, cone and jaw crushers. All crushers operate in aggregate production plants in Poland. In the first stage of investigations there were determined dust emission levels and supporting characteristics for all crushers under investigation. Then there were introduced indices that allow for comparative analysis in terms of dust emission, for devices with different energy consumptions and comminution ratio. It appeared that crushers with high the overall dust emission do not always achieved unfavorable dust emission per comminution ratio or energy consumption. The introduced indices proved their usefulness, because they helped to carry out a comparative analysis among crushers, operating under different technological conditions. It is also easier to assess environmental impact of individual crushing devices, under analysis. Results of investigations also show that environmental impact of different types of crushers is diverse and it is difficult to compare dust emissions of various types of crushers without taking into account technological aspects (like throughput, comminution ratio, energy consumption, and others) of their operations.INTRODUCTION Mineral processing of raw material is a complex process, involving in general operations of size reductions and separation. Depending on the type of specific raw material, the technological circuit may include operations of comminution and size classification. This is a typical circuit for aggregate production. In ore treatment industry the process in much more complicated and include also a metallurgical treatment of ore concentrate – the final product from processing plant stage.In general, regardless the type of raw material, operations of size reduction are present in each technological circuit of mineral processing. Operations of crushing and grinding are an integral part of processing technology, because they play a crucial role in effective treatment of mineral raw materials (Gawenda 2013). Their duty is to liberate the useful minerals from the gangue in ore treatment industry, or to produce the material with the required particle size in case of aggregate processing. Crushing and grinding operations are of a high negative impact on environment and humans. They consume great amounts of energy, what indirectly contributes to higher emission of carbon dioxide CO2. Apart from energy, crushing and grinding device consume significant amount of steel and other metals and alloys due to high wear of working parts and grinding media. This is also of negative environmental impact due to emissions of additional amounts of CO2 in production of steel and other metals required as spare parts for comminution devices."

Jan 1, 2018

By D. M. R. Sekhar

Certain types of rock phosphates of sedimentary origin are applied to acidic soils as fertilizer directly. Recent research in India showed that high grade rock phosphate in fine size when used as a mix with organic manure works as efficiently as di-ammonium phosphate (DAP) in alkaline soils. The rock phosphate from Jhamarkotra, India (sedimentary origin), Egypt (sedimentary origin) and South Africa (volcanic origin) showed good agronomic efficiency when used as Phosphate Rich Organic Manure (PROM). Further PROM shows equal residual effect. The results of efficiency of PROM made using two grades (+ 24% P2O5 and 34% P2O5) of rock phosphate mineral from Jordan show that low grade rock phosphate slimes are as effective as high grade phosphate concentrate when used in PROM. Also PROM is very effective in the saline soil of Eshidiya desert where DAP is not at all effective.

Jan 1, 2014

By Ahmad Amini, Hadi Abdollahi, Pouya Karimi

Due to detrimental effects of cyanidation process on the environment in gold industry, application of cyanide alternatives such as thiourea are being highly considered in recent projects. In this study, the extraction of gold from poly metal ore, using thiourea was precisely investigated. The representative sample contained 2.5 ppm Au and 160 ppm Ag. The sample was categorized as oxide gold ore, because the main part of its pyrite was changed to iron oxide and hydroxide such as goethite and lepidocrosite. According to mineralogy, the main gangue mineral was quartz. It shows that gold grains are free and interlocked with quartz matrix. Also, the presence of a high amount of silver in free and sulfide forms and also the low content of other sulfide minerals such as base metal sulfides is a remarkable point of these studies. In the gold extraction process with thiourea, there are several parameters that affect the rate of gold dissolution such as concentrations of thiourea as a gold lixiviant and ferric sulfate as an oxidant, pH and size fraction of feed and leaching time. The influence of these parameters on the gold dissolution rate were investigated and optimized. The results showed that the concentration of thiourea is the most influential parameter which could increase the gold recovery to 71% (at 10 g/kg sample). The optimal amount of ferric sulfate was determined as 6 g/kg sample. Also, the optimal levels of size fraction of feed and pH of solution were 88% under 75 micron and 2 as acidity; respectively. Leaching time was 6 hrs. In addition, this sample was leached with cyanide and the optimized values of size fraction of d88=75 microns, pH=10.45, 2500 ppm of sodium cyanide with time leaching of 24 hours were concluded for maximum recovery of gold in solution. Finally, the results of cyanidation tests were compared to the thiourea dissolution after optimizing all affected parameters in cyanidation process.

Jan 1, 2018

By Hermann Wotruba, Günther Petzold, Fabian Riedel

"Increased mechanisation in underground stoping operations results in higher waste percentages in the run of mine. A new method of reducing waste is optical sorting. Optical sorters have low maintenance costs and can be installed underground. Rejected waste can be backfilled directly without having to be hoisted, therefore increasing the shaft capacity for a more valuable product.Pre-Concentration by Optical SortingA series of tests with an optical sorter at the laboratories of the Mineral Processing Department of the RWTH Aachen have shown that it is technically possible to sort almost any kind of ROM which has even slight differences in colour (Platinum Reef, Gold Reef, Kimberlites, Industrial Minerals, Aggregates, Coal, etc.).By employing optical sorters prior to conventional sorting plants, it is possible to reduce the amount of waste to be processed. Figure one shows test results of ore which is quite similar in colour to the waste (grey). With increasing waste in the feed, the recovery decreases according to the graph. In figure two, the colour ratio parameter of the sorter was changed with a similar waste percentage in the feed. With increasing loss of ore, a cleaner product can be achieved. Before designing a sorting plant, throughput tests are carried out. Throughputs vary depending on the size range. Sorters have a limit of about 250mm top size. In this upper size range, throughputs of 150t/h can be achieved."

Jan 1, 2003

By M. Pelser, Lorenzen L.

"The presence of calcium and magnesium in the hydrometallurgical processing of base metals, results in a number of process difficulties. These problems range from the contamination of the final product (where the final product is a precipitate) to high energy consumptions and large bleed streams during electrowinning. Calcium poses an additional problem in sulphate solutions owing to the low solubility of its sulphate salts. This can easily lead to a process stream that is supersaturated with calcium sulphate, resulting in unwanted solids formation within the process equipment.A review of literature has proven that there is no conventional method for the control of calcium and or magnesium, although a number of potential processes have been identified. The technologies investigated included precipitation, ion exchange and solvent extraction, for which at least one method was found under each. To make the reader aware of these processes a short description was provided of each within the text.Of these processes, fluoride precipitation was selected for experimental investigation based on the low solubility of calcium and magnesium compared to the base metals. This process involves the addition of a soluble fluoride to precipitate CaF2 and MgF2. The experiments were designed to investigate the equilibrium of the system at varying parameters of which the level of fluoride addition, the ratio of calcium to magnesium, and the identity of the soluble fluoride was reported. In all of the instances the process showed high selectivity towards calcium and magnesium over the base metals. The experiments proofed the process to have a higher affinity towards the removal of magnesium at compositions where the molar ratio of calcium to magnesium was higher than 1:3. It is often the case that the calcium to magnesium ratio is in the region of 1: 10. From this it follows that the fluoride addition has to be stoichiometric or greater for calcium and magnesium combined, if the calcium is to be precipitated. This was demonstrated as well. On the identity of the soluble fluoride hydrogen fluoride was compared to ammonium fluoride, of which the latter was found to be preferred."

Jan 1, 2003

By M. Bhartia

India is the 5th largest producer of steel in the world and is slated to produce more than 180 Mt by 2020. Expectedly about 50 % of this would be through the Blast furnace route and the rest through Sponge iron / DRI route. Considering that there will not be any major change in iron making technology by that time, the Blast operation would require lump ore (10-40mm) with around 64% Fe grade and sinter fines (<10mm) with 60% Fe (min) as its feed. DRI process would need calibrated ore of size 5-18 mm as the most suitable size of feed. It is also expected that of the total requirement of ore for the DRI route a significant part would be DRI pellets. In India, there is considerable debate going on regarding the technology to be adopted for the processing of iron ore and there is a lack of clear consensus. The above scenario indicates that the processing requirement of iron ore in the country would involve both washing technology as well as beneficiation technology. CDE Asia Ltd is in the forefront of iron ore processing in the country and the experience gained by the company over the last few years of functioning has led the company to believe that route to be adopted depends on the end product requirement and the starting grade of the feed. Keeping in mind the nature of the feed required for the Blast furnace & DRI operation; it is obvious that good washing technology would be highly beneficial to the iron ore industry. Depending on the grade of ore available the limits of washing will be decided and equipment for lump ore beneficiation such as jigs could be incorporated into the washing circuit. Scrubbing of ore either before washing or selectively scrubbing the lumps could be necessary. Very low grade ore and jig rejects would be required to be totally ground and beneficiated for the production of pellet feed in order to utilize the iron ore resources entirely. Another source of ore for pelletisation would be slimes generated from the washing process as well as the huge quantities already available in the tailings dams in the operating mines. Deslimimg and magnetic route of beneficiation could release at 30-40% of the Fe locked up in these tailings ponds/dams. The paper describes the concept with examples from operating plants and proposes how the adoption could be engineered through test work and proper plan of integration. Keywords: washing, beneficiation, iron ore, lumps, sinter fines, pellets, jigs, screens, evowash, nanowash, thickeners, log washers, drum scrubbers

Sep 1, 2012

By M. L. Wu

A moderately thermophilic acidophiles strain had been isolated from the bio-heap leaching plant in Zijinshan Copper Mine, and the identification based on the PCR-16S rRNA gene sequence homology analysis with morphologic and physiologic methods was conducted by polyphasic taxono-my and phylogeny research. The results show that the strain by depurated belongs to Acidthiobacillus genus and is considered as Acidthiobacillus albertensis.

Jan 1, 2014

By X. L. Song

In this paper, ZrSiO4-Cd(S1-xSex) inclusion pigments were synthesized by hydrothermal method. Microstructure, morphology and properties of the powder were characterized by X-ray diffraction (XRD), transmission electron microscopy (TEM), infrared spectroscopy (IR) and CIE chromaticity, respectively. It shows that, precursors obtained at pH is about 6.0 are sol and products with higher crystallinity, red hues (a*=38.23) and inclusion ratio when hydrothermal synthesis temperature is 180? and holding time is 12h. Hydrothermal reaction mechanism was further analyzed as well. In particular, an ideal model of pigment formation was proposed.

Jan 1, 2014

By Y. H. Tang, H. Y. Zhang

"Tailings from lead-zinc mine contain plenty of dolomite and low-grade fine-grained barite, which is difficult to enrich by mineral processing. Since the density of barite and dolomite has some differences due to the fine dissemination size in a complex sedimentary, the gravity separation tests were conducted with no results obtained. The magnetic separation was conducted to remove the magnetic gangues, and the results were not satisfactory because of the gangue minerals such as limonite and others were low in content. The results of floatation tests showed that the mineral separation of barite and dolomite is quite difficult because that they have similar mineral floatability. Experimental research shows that the good results can be obtained by “desulfurizationbarite floatation” processing with the new depressant TS. The barite concentrate containing BaSO4 91.27%, BaSO4recovery is 70.25% when sodium dodecyl sulfonate serves as a collector and TS as the depressant.INTRODUCTIONBarite is an important mineral material. Often associated with other minerals, it usually needs to be separated by mineral processing in order to meet the application requirements. The main barite beneficiation methods include hand sorting, gravity separation, floatation, magnetic separation, acid leaching, etc. Usually barite associated with oxide ore such as fluorite dolomite, quartz ore etc. are also associated with sulfide ore such as pyrite, sphalerite and galena. The separation between barite and sulfide ore (such as pyrite) is easy. On the other hand, the separation between barite and oxide ore (such as dolomite and fluorite) is very difficult. There are quite a lot of reports on the separation between barite with fluorite dolomite however the separation between barite and dolomite is seldom discussed.The ore properties are quite complex attributable to mineral assemblage containing a large amounts of dolomite. As the density of barite and dolomite has some differences, gravity separation between them is usually easy. The gravity separation tests were conducted with no results obtained due to the fine dissemination size in a complex sedimentary. The magnetic separation was conducted to remove the magnetic gangues, and the results are not satisfactory as the gangue minerals such as limonite and others were low in content. Due to the fine dissemination and intimate association of minerals, and barite and dolomite contain the same group ions of Ba2+, Ca2+ and Mg2+, the results of flotation tests showed that the mineral separation between barite and dolomite by flotation means problematic. Previous studies have been conducted by several institutions but none to date has come up with a satisfactory process in dealing with the deposit. This may be attributable to: high cost of reagents; unsatisfactory performance. Therefore, the key to the flotation separation of barite and dolomite is the application of selective inhibitors. Based on previous test observations and years of extensive research experience in barite processing technology, with the new depressant TS has selectivity inhibition on dolomite developed and used, good results can be obtained by “desulfurization-barite flotation”, which allows barite in the lead-zinc tailings to a comprehensive recovery."

Jan 1, 2018

By X. Q. Wu

Magnetization in slurry (MIS) of weakly magnetic minerals by iron ions was investigated. The magnetic seeds (strongly magnetic particles) were synthesized by ferruginous chlorides directly in slurry instead of previous preparations of magnetic seeds by finely grinding mineral magnetite or specially synthesizing them separately in an aqueous solution. In this way, the growth of the seeds and their adsorption on the minerals simultaneously take place in the same slurry. That after MIS the recovery of weakly magnetic mineral limonite in a magnetic separator increased means the formation and adsorption of magnetic seeds on the surface of iron mineral limonite. The magnetization effect was evaluated by limonite recovery at a magnetic strength of 3.500 Gs in a magnetic separator. Mineral limonite was properly magnetized in the following slurry condition: molar ratio of Fe3+ to Fe2+1:3, slurry temperature of 45 °C and pH 10.5. The selectivity of the magnetization between minerals limonite and quartz was improved by adding surfactant sodium oleate.

Jan 1, 2014

By Kari Niiranen, Andreas Fredriksson

LKAB (Luossavaara-Kiirunavaara AB) is operating iron ore mines, concentration plants and pelletizing plants in Northern Sweden. Geometallurgy, which combines geological and metallurgical information is not a new way of thinking at LKAB, but rather a revised and updated version of an old working process. A project called "Silica in the Mine" which started in 2007, was an important reason to set a new focus at the geometallurgy. The target of the project was to develop a simplified method in laboratory scale to predict SiO2 grade in the magnetite concentrate in Kiruna and further predict the physical properties of the crude ore with respect to processing characteristics. The connection between mineralogy and products properties have started to be even more vital and necessary to examine due to the future exploiting new iron ore deposits. Geometallurgy at LKAB can be described as a mental and strategic framework where the Research and Development department (R&D), and others within the organization of LKAB, aims towards the connection of the minerals-production-products. It could in its basics be called "research & development", but it must be clarified that changes have been made, mainly due to the development on the instrumental analysis side. LKAB’s idea is to work quite broad, with internal educations, an active working process in ongoing projects, together with external parties (such as universities), with several PhD-projects and an upgrading on the instrumental side at the LKAB Research & Development department. This paper is a summary about the concept Geometallurgy at LKAB and some of the actions within its framework.

Jan 1, 2014

By Liu Jie

Refractory iron ore deposits in China have various genesis and complicated types, the nature of which is poor, fine-disseminated and complex. Therefore, refractory iron ore could scarcely be separated and utilized by traditional mineral processing technology at present. It is necessary to explore deep reduction technology to change the characteristics of refractory iron ore and to use effectively the iron resource. And deep reduction technology is that on the condition of higher reduction temperature than that of magnetic roasting and stronger reducing atmosphere, the iron oxides from iron ore was reduced to metallic iron particle that is easy to dissociate. And then production from deep reduction is easily separated by magnetic separation and iron powder production was obtained finally. Deep reduction technology for Lingyang iron ore from Jilin, China, as the refractory iron ore, was studied in this paper. The influences of such main factors as reduction temperature, time and coal content were investigated. The results showed that the Metallization rate of reduction product was up to more than 90% under optimum conditions, and then higher iron grade and recovery of reduction iron powder were obtained from subsequent magnetic separation. Furthermore, the deep reduction mechanism in the system was studied by the means of XRD and SEM analysis for reduction production and Physical Chemistry of Metallurgy. Analytical results indicated that during deep reduction, the size of iron particle from deep reduction materials was increasing as reduction temperature rising and reduction time extending. The growth of metallic iron particle from deep reduction production was divided into such three stages as reduction nucleation, deep reduction and growth of metallic iron particle.

Sep 1, 2012

By Q. Zhang

This paper, by studying the surface properties of pure dolomite minerals separated from representative marine sedimentary rare earth-bearing phosphate ores in Zhijin, Guizhou, aims to study the effect of different anions on the ? potential of dolomite. The research findings showed that the dolomite mineral had a point of zero charge (PZC) at pH 6.5, and the PZC shifted towards lower pH values with addition of anion SiO32- and PO43-. However, addition of anion CO32- and F- resulted in higher PZC values. Keywords: dolomite, ? potential, PZC, anion

Sep 1, 2012