Search Documents

By P Stone, J. M. Cook, P. R. Simpson, C Mcdermott

Paper presented at the conference Economic geology in Europe and beyond II, models for mineral deposits in sedimentary basins, held in Keyworth, UK, 13-14 April 1994. The SW part of the Southern Uplands is a back-arc section of an accretionary thrust system, divided into structural blocks by major NE-SW shear zones and NW-SE faults forming the margins of Permian half-grabens. The highest arsenic levels in stream sediments (over 65 ppm) are associated with those blocks carrying brittle-ductile transition fabrics. Three factors combine to recomend the area as having potential for gold mineralisation: As-rich greywackes as country rock, felsic intrusions and a major shear zone. Selected stream sediments were analysed for gold using lead fire assay with ultra-pure flux and ICP-MS finish. Several localities showed over 15 ppb Au, the three most significant being within the hanging wall of the Orlock Bridge Fault and each having distinct characteristics

Aug 1, 1995

By B. R. Reddy, Y. V. Swamy, B. V. R. Murthy, H. S. Ray

The Ni oxide was reduced with a CO-CO2-N2 gas mixture and the effects were observed of process variables such as roasting temperature, time and CO partial pressure. Extraction of over 90% of Ni was achieved by ammoniacal leaching of ore that had been reduced for 1 h at 760 degrees C under a gas mixture with a volumetric CO/(CO+CO2) ratio of 0.57. The kinetic data were found to conform to the Ginstling-Brounstein equation. The applicability of this model was confirmed by evaluating the apparent activation energy with the use of independently constructed differential and integral plots, which showed an excellent match

Dec 1, 1995

By A. K. Tripathy, P. K. Pattnayak, H. S. Ray

The effects of water addition on the solid-state reaction between Cr2O3 and Na2CO3 at low temperatures (up to 873 K) were investigated to determine its possible influence on the reaction rate and the degree of conversion to soluble chromate. Experiments at high temperatures were conducted for comparison. It was found that adding water to the mixture before roasting enhanced both reaction rate and yield significantly. The reactions followed the Lesokhin-Tempelman equation at low temperature and the Ginstling-Brounshtein equation at above 973 K; the respective activation energies were 95 and 22 kJ/mol

Jun 19, 1905

By W. R. Paterson, W. Morton, D. B. Cameron

The Massbal II computer simulation program has been used to develop a general framework for the building of thermochemical models of metallurgical processes. The framework allows the rapid, simple construction of complex models of process equipment for use in flowsheet design, planning and plant operation. Application of the program to model the iron-making blast furnace and a flash smelting process is described

Apr 1, 1991

By G. Kill

Although other energy commodities have developed successful futures contracts, long-term contracts still dominate the coal market. To establish whether coal markets will develop in the same way, coal price and volume data are tested against a set of criteria considered to represent some of the factors contributing to the development of a successful futures contract. Coal meets only some of the criteria: market players are subject to little risk in quite a stable market, have strong preferences for the specific nature of long-term contracts and profit from product uniqueness, each trade being individually negotiated. Potential structural changes in the western European market are not felt to be sufficient to create demand for a coal futures contract, but an empirical model has been developed that could form the basis of a further study to predict the potential for success

Aug 1, 1994

Errors in ore reserve estimation can occur during drilling and sampling, sample preparation and analysis, geological logging and modelling, database construction, statistical or geostatistical evaluation, selection of economic parameters, selection of ore reserve method and assessment of mining constraints. Core sample recovery can be a major source of error, and it is proposed that the modelling of grade, metal accumulation and thickness should be accompanied by the modelling of core recovery (or core loss) so that for each ore block a weighted block recovery factor is obtained. This gives a good indicator of the reliability of a reserve estimate. It is suggested that a resource reliability rating (RRR) system be established to quantify what is meant by geological assurance and to combine this with an estimate of the precision of estimation as gained by geostatistical analysis. Proven and probable minable reserves would be those with an RRR better than 50% and a precision of estimation better than 20%

Dec 1, 1996

By M. Feely, W. G. O'Keefe, C. O'Reilly, M. P. Holdstock

A petrographic and microthermometric study of fluid inclusions in the Kentstown Granite, crosscutting quartz (VI) and calcite+quartz (V 2) veins in the granite and calcite+quartz (V 2) veins in the overlying sediments was performed on samples taken from the borehole. Comparisons of the type 1, type 2 and type 3 fluid inclusion populations recorded in the present study with those from other Irish Caledonian granites strongly suggest a similar fluid evolutionary history. Furthermore, the low-temperature CaC12-rich brines (type 5) of this study, which must be syn- to post-Lower Carboniferous in age, have correlatives both in Irish Caledonian granites and in the Lower Carboniferous base-metal deposits of the Irish midlands

Jun 19, 1905

Carbon anode cells were studied by two-dimensional computer simulation to evaluate their suitability for alumina electrolysis at high superficial current densities. The most efficient anode arrangement was needed to overcome the electrochemical disadvantages of alumina's low solubility in chlorides. Cells with packed-bed anodes might provide practical superficial current densities greater than 0.67 A/cm2 when the granule size was less than 1 cm, but in the process of electrolysis the granules within the active zone would be consumed and become smaller, affecting alumina concentration transport. For zones of very small granules a concentration-dependent model should be considered; for more complete consideration a time-dependent model can be introduced to describe the variation of granule size and its influence on mass transfer and polarisation

Jun 19, 1905

By T. C. Alex, S Srikanth, Premchand

It has been suggested that reduction of the iron and manganese phases as far as FeO and MnO is preferred for the complete liberation and selective reduction of the copper, nickel and cobalt oxides in manganese nodules. The oxygen partial pressure/temperature regime suitable for this purpose has been delineated. Free-energy minimisation and thermogravimetric results indicate that the requisite conditions can be achieved if more than 10% of neutral oil is used at temperatures greater than 923 degrees C. Neutral oil content, temperature and roasting time have been optimised to maximise leaching recoveries of Cu, Ni and Co: up to 96% of Cu and Ni and up to 85% of Co can be recovered if 15% of neutral oil is used as a reductant at 973 K for 90 min

Jun 21, 1905

By R. H. T. Garnett

N.B. This paper provoked much (positive!) discussion in later issues, with responses from the author (and thanks also for the many private contributions he had received) - see under Garnett R.H.T. Expanded version of a paper originally presented at the Alluvial mining conference, London, 11-13 November 1991 and published in Alluvial mining, Barking: Elsevier Applied Science for IMM, 1991, p.115-156. The usual measure of performance in gold and tin dredging is the R/E factor. It compares actual production or recovered grade for a given period with that estimated from the original sampling. The factor is a multiple of four component factors, each ideally approaching 1.00. The factors are concerned with estimation, selection, excavation and treatment. The estimation factor reflects the errors involved in determining the grade and depth of single drill-holes or pits. An optimum selection factor is achieved by a higher drilling density. The excavation factor is affected by failure of the dredge to excavate the total volume contained within its course. The required dredge throughput rate influences not only the success in digging recovery but also the treatment factor. No two alluvial deposits are the same, but, in general, the greatest divergence from 1.00 is invariably demonstrated by the estimation factor. A major divergence in one of the other factors may also be the cause of the R/E factor being significantly different from 1.00. The component factors are examined in detail and historical trends in R/E factors are discussed

Sep 1, 1991

By P. Golledge, A. D. S. Gillies

An investigation has been carried on samples of three Queensland coal dusts to determine the potential explosibility of dust-gas mixtures. The explosion potential of the samples was classified by the lean and rich limits of explosibility and the limiting oxygen concentrations for each sample. Plotting of these points showed 2-dimensional flammability limit surfaces for coal dust/oxygen, methane/oxygen and coal dust/methane mixtures. From these plots the 3-dimensional flammability envelopes defining the explosibility of the mixtures were defined. The explosion limits of the coal dust/methane/oxygen system were seen to be influenced most by the explosibility characteristics of coal dust. Methane exerted a stronger influence over the explosion limits when the coal had a low volatile content

Jun 19, 1905

By R. Sweennen, A. Vervoort, J. Caers

A case study is presented of the mechanical behaviour of fractures in the Westphalian A and B siliciclastic succession of mud-, silt- and sandstones with intercalating coal layers in the Campine basin of northeast Belgium. Mining ceased in the area in 1992 and a pilot well was drilled to assess the feasibility of methane extraction by hydraulic fracturing. Work was carried out to study the influence of types of cement fill in fractures on the shear behaviour of the rocks by comparison with that of the coal seams. X-ray computerised tomography was used for visual appraisal and selection of jointed rocks before destructive shear testing was carried out. Two major type of veins were found to be present, one cemented with carbonate and the other with kaolinite or kaolinite/carbonate. Uniaxial compressive strength and shear tests showed that differentiation of the two types of veins was vital in evaluating the strength of the sandstones, as cementing of the fractures by rigid carbonate minerals can reinstate the strength of the rock masses to that of the intact material. Kaolinite was more susceptible to plastic deformation than carbonates

Jun 19, 1905

By R. L. F. Kay, T. A. Fletcher, A. J. Boyce, C. M. Rice

Paper presented at Mineralisation in the Caledonides, the Mike Gallagher memorial meeting held in Edinburgh, 27-28 June 1996. The synorogenic, mafic Ordovician intrusion comprises orthopyroxene-rich xenoliths and mafic-ultramafic cumulates with low-grade pyrrhotite, chalcopyrite and pentlandite mineralisation. Despite abundant textural, mineralogical and O isotope evidence for significant assimilation of country rocks, S isotopes indicate only a modest uptake and suggest that mineralisation is dominated by magmatic sulphur. The preferred explanantion is that the magma was close to S saturation on emplacement. Uptake of elements such as Si and O led to early crystallisation of orthopyroxene, resorption of olivine and early segregation of a sulphide liquid. Post-magmatic interaction with a high-temperature, surface-derived fluid, whose movement may have been controlled by regional shear zones, reset biotite and whole-rock O isotope values but not those of orthopyroxene. This model identifies the presence of olivine-rich rocks and evidence of extensive assimilation as guides to prospectivity

Jun 19, 1905

By J. H. Morris, G. M. Steed

Paper presented at Mineralisation in the Caledonides, the Mike Gallagher memorial meeting held in Edinburgh, 27-28 June 1996. Oxygen isotope analysis indicates that quartz, carbonates and muscovite could all have formed in near-isotopic equilibrium with the mildly saline H2O-CO2 ore fluid at 330 degrees C. Calculated values for O, C and S in the ore fluids imply derivation from a deep, homogeneous source region and are consistent with formation either as a direct or an indirect result of igneous processes. Values for delta-O18 plot a little outside the accepted magmatic range, but have almost certainly been modified by exchange reactions with wall rocks. These reactions were also the most likely cause of deposition of the ore constituents. The chemical and isotopic character of the fluid was similar to that in many Archaean and later mesothermal auriferous vein systems, especially the Mother Lode region of California. If the Southern Uplands-Longford Down accretionary complex conceals an Ordovician arc, the tectonic setting was also broadly comparable

Jun 19, 1905

By S. P. Ball, A. J. Monhemius

In a laboratory study under acidic oxidising conditions, the thiocyanate system gave results at least as good as cyanide and considerably better than thiourea, with modest consumption of SCN (less than 1 kg/t ore). For both cyanide and thiocyanate lixiviants a residence time of about 24 h was required for maximum gold extraction, which was generally in the range of 92-96%. The adsorption of gold from thiocyanate leach liquors was found to be rapid, but activated carbon catalyses the autoreduction of ferric iron to ferrous iron in thiocyanate solutions, suggesting that ion exchange may be a better recovery route

Dec 1, 1995

The reduction of zinc from slags by a molten, carbon-saturated bath was examined in a laboratory study under conditions of continuous slag feeding. The results show that it is possible to reduce the bulk of the zinc from the slag before there is a net reduction of iron. However, the recovery of zinc was not as high as in batch tests performed in an earlier study. Lead in the slag was reduced simultaneously with the zinc to very low levels and was volatilised. Copper in the slag was reduced and dissolved in the alloy. An attempt was made to identify potentially commercial ways of treating zinc slags using an iron bath. The approaches that appear to have the greatest potential are reduction in a batch process using electrical heating and reduction in a continuous process with co- or countercurrent flow of the slag and alloy. In the latter the alloy would be prepared in a separate furnace before being contacted with the slag. The purpose of this would be to superheat and carburise the alloy so that no additional heat or reductant would have to be supplied in the slag-alloy reactor

Jul 1, 1991

By A. M. Tunstall

Aspects of blast vibrations, damage mechanisms and the influence of rock quality on damage severity are reviewed and results presented from a monitoring programme in which the rock mass rating for six tunnels was determined. The peak particle velocity induced in the tunnels during open-pit blasting was measured and the tunnels were inspected visually for fresh damage after each blast. The results suggest that the quality of rock in which an excavation is situated has an influence on the level of ground vibration to which it can be subjected without sustaining damage. This means that the use of a single limiting value of peak particle velocity, as in the blast damage criteria for residential structures, is not ideal and may result in damage to excavations in poorer-quality rock masses

Jun 19, 1905

By R. M. Cooper, H. K. Herbert, D. N. Phillips

A study was carried out to determine the effects of adding CaCO3, Fe, Al and CaSi2 to the ladle, rather than to the raw materials, in order to increase the concentration of Ca, Fe and Al in the final product to meet customer specifications at Simcoa's Kemerton plant in Western Australia. LA-ICP-MS, SEM-EDXRA and ICP-AES analysis of samples and controls showed that the technique is suitable for controlling minor element concentrations. Iron was successfully added, while calcium silicide with aluminium proved better than limestone with aluminium for controlling Ca and Al concentrations in the silicon

Jun 19, 1905

By D. M. Milne, P. J. Lunder, R. C. Pakalnis

During the mining of an open stope, deformation of the hanging-wall and the potential for dilution generally increase with the size of the exposed hanging-wall. Excluding discrete structures that may delineate unstable blocks, the mechanisms that drive hanging-wall deformation and possible dilution comprise several factors which can include elastic, plastic and discontinuum deformation. These stages of deformation are not mutually exclusive and at any point during mining all three of these mechanisms may be acting on the hanging-wall rock mass. Computer modelling techniques are available to analyse the three stages of deformation, but the difficulty lies in trying to obtain realistic rock mass properties for input and in determining when each stage of deformation is acting. Instrumentation data can be used to predict the effect of continued mining. However, it is often difficult to calibrate numerical models against field data owing to the large number of input parameters required. An empirical approach is recommended that uses two new parameters, the radius factor and the effective radius factor. A method is proposed for predicting the effect of continued mining from existing deformation and dilution data for a given hanging-wall

Apr 1, 1996

"Prior to the publication of the General Report of the Miners' Phthisis Prevention Committee of South Africa in 1916 little attention was paid to the dust hazard and the necessity for its suppression in the underground workings of the Broken Hill mines. Such precautions as were observed for the elimination of dust were related rather to the prevention of lead poisoning, which, in the early days of Broken Hill when large tonnages of lead carbonate ore were being won, was rather prevalent. Ventilation and hygiene followed the general practice in this and most foreign countries.This paper covers incidence and action since 1918, considering medical aspects and operating aspects. "

Jan 1, 1947