Search Documents

By R. Immele-Meziou, G. J. Long, D. G. C. Robertson, O. A. Pringle

The reduction of naturally weathered ilmenite concentrate occurs in two steps: reduction of Fe3+ to Fe2+, followed by reduction of Fe2+ to Fe. Small amounts of a magnetic phase were also observed and may correspond either to an Fe3O4-FeTiO3 ilmenite phase or to an Fe3O4-Fe2TiO4 spinel phase. The total amount of metallic iron produced after 12 hr was only 50% of the total iron present in the sample.

Jan 4, 1992

Discussion at the Midland Institute of Mining, Civil, and Mechanical Engineers' general meeting held in Leeds, March 21st, 1916, with T. Beach, vice-president, in the chair, of a paper published in Trans. Inst. Min. Engrs., 1916, vol. L., page 509, comprised a written contribution by O'Shea L.T.

Dec 1, 1916

By T. F. Bamber

The South Nottinghamshire Area has not been greatly troubled by spontaneous combustion until the last few years, during which the Blackshale Seam has been developed and exploited. The problem was first encountered at a colliery which was heavily preoccupied with a major reconstruction scheme, and with the sudden appearance of a completely new hazard both men and management had to adapt themselves very quickly to meet the situation. The paper contributed to the Symposium by the South Nottinghamshire Area illustrates the problems by reference to actual incidents, and shows how the lessons learned from them have been applied to the shaping of future policy on the avoidance and treatment of spontaneous combustion.

May 23, 1905

By D. C. Yates, G. V. Jolliffe

In the five coalfields of Staffordshire, there have been some 43 incidents of spontaneous fires and heatings which have required special attention in the past ten years. This total excludes incidents in the Thick Coal Seam of South Staffordshire, which was worked until 1967, and which was subject to an almost continuous series of heatings. The incidents have been classified to show the sites of occurrence, the contributory factors which may have caused them and the treatments applied to them. The remedial techniques, as practised in Staffordshire, are dealt with in detail, with particular reference to standard methods of stopping-off. Precautionary measures taken are described, including a "liability to spontaneous combustion" classification of all seams, and the setting up of an emergency organization with emergency stocks of materials and equipment. The paper is concluded by a few words on the organization and control at the time of an incident.

May 23, 1905

Jan 1, 1947

By P. Beauvais

Philip Beauvais, from the Met Office's International Mining and Agriculture Department, explains the need to understand the impact of the weather and climate when developing future mine sites.

Mar 1, 2015

By R. W. Ruddle

The present state of knowledge on this subject may briefly be summarized as follows: (1) The copper content of the slag increases with the grade of the matte in contact with it; on the other hand, the proportion of copper lost decreases as the matte grade increases, because as a general rule a smaller volume of slag is produced when a high-grade matte is made. (2) The presence of CaO and MgO in the slag decreases the copper content of the slag, and the presence of ZnO increases it; the presence of A1203 seems to have little effect. The influence of the silicate degree is not yet clarified, but on theoretical grounds it seems likely that the copper content increases with the silicate degree of the slag. (3) High slag viscosity, high magnetite contents and low density difference between matte and slag all tend to increase the copper loss. The volume of slag is also an important factor. (4) The effect of bath temperature on the copper loss is not clear and further investigation of this point is needed. (5) It appears possible to recover a large part of the copper in the slag by adding FeS, CaS and other sulphides

Jan 1, 1953

By T. Guerin

More than 370 million litres of oil leak from hydraulic equipment every year, excluding all other sources of plant fluid losses. This item analyses the causes of fluid spills from plants and equipment on resource construction sites, and offers some possible solutions.

Apr 1, 2015

The first part describes a model (the C model) based on the motion of the grinding charge. The charge is treated as a continuum, which allows analytical solutions to the equations that are developed. The C model is equally applicable to ball-, semi-autogenous and autogenous mills and contains a description of the power draw of both the cylindrical section and the cone-ends. Differences between the power draw of grate- and overflow-discharge mills are described from consideration of the different shapes and compositions of their charges. A large database of industrial mill data is used to demonstrate the accuracy of the model. Part 2 describes a simpler, empirical model (the E model) whose performance is based on that of the C model. The same database was used to assess the predictive capabilities of the E model. The model was shown to be only slightly less accurate than the C model despite its much simpler structure

Jun 18, 1905

By C. M. Lesher, R. R. Keays

"The komatnte-associated Fe-Ni-Cu sulphide mineralization at Kanihalda, Western Australia, is generally believed to be magmatic in origin, but a number of postmagmatic processes significantly modified the original distribution, structure, texture, mineralogy and chemistry of the ores. Two important types of mobilized magmatic sulphides are interpillow/interbreccia sulphides and hydrothermal vein-type sulphides. Interpillow and interbreccia sulphides occur interstitial to pillowed or volcaniclastic footwall metabasalts beneath or adjacent to the stratiform contact ore horizons. They are mineralogically and compositionally similar to massive ores (and are similarly depleted in PGE relative to the compositions of bulk samples of mined ores), but normally do not contain the distinctive chalco-phile ferrochromites characteristic of contact ores. They are interpreted as magmatic sulphides that have been mobilized from the overlying or adjacent massive sulphide layer during peak tectono-nietamorphism.Hydrothermal sulphide-quartz + albite veins also occur in the footwall metabasalt and contain unannealed deformation fabrics indicative of emplacement during retrograde metamorphism. The high Ni and Pd contents of these sulphides (7-13% Ni, up to 70 ppm Pd) indicate that the metals have been derived from the spatially associated komatiites and/or contact ores, consistent with the Pd depletion previously inferred for massive ores. Very low Ir contents and high Pd/Ir ratios of the vein-type sulphides confirm an aqueous transportation-deposition mechanism; hydrothermal transfer of PGE results in strong decoupling of Pd from Ir.There appears to be a complete continuum of sulphide mobilization at Kambalda ranging from whole-scale phy sical dislocation (fault offset ores) and selective mobilization (stringer sulphides) through nietamorphie replacement (interpillow/interbrec- cia sulphides) to jiydrothermal dissolution and redeposition (vein-type sulphides)."

Jan 1, 1984

By A. J. Naldrett

"Synorogenic mafic intrusions are a common feature of the northern Appalachians. Two sulphide-bearing intrusions in central Maine that have been investigated revealed a number of important features that illustrate sulphide-silicate interaction that relates to magmatic sulphides. The Moxie Pluton is a large mafic intrusion emplaced during the Devonian Acadian orogeny. The Katahdin gabbro is a small mafic body that is probably genetically and temporally related to the Moxie Pluton. Both intrusions were formed bv the intrusion of variably fractionated magmas into irregular chambers and feeder zones. The southern half of the Moxie Pluton contains three small sulphide accumulations, whereas the Katahdin gabbro hosts a large, predominantly massive, sulphide body. Textural evidence clearly documents the magmatic origin of these sulphides.The three Moxie Pluton sulphide bodies are located at or very close to the intersection between the intrusion and the sulphidebearing Hildreths Formation. Sulphur assimilation, suggested by this relationship, is supported by the isotopically light (634S = —8 to —25) and the selenium-poor (S/Se - 25 000-48 000) character of the Moxie sulphides and correlation with the Hildreths Formation sulphides (S34S = —25, S/Se = 25 000-48 000). Isotopically light sulphur (534S = —20 to —21) and high S/Se ratios indicate that the majority of sulphur in the Katahdin sulphide body was also derived from an unexposed country rock source. The volume of sulphide in this example illustrates the potential efficiency of the sulphur assimilation process—so efficient in this case that marked dilution of the economic chalcophile elements resulted from the addition of so much external sulphur.The three Moxie Pluton sulphide occurrences are all impoverished in Ni and Cu (1.87-0.44% Ni; 0.72—0.32% Cu in massive sulphide), but contain normal Co contents (0.22-0.13%) relative to typical magmatic sulphides. The Katahdin sulphides show a greater Ni and Cu impoverishment (0.2% Ni; 0.1% Cu in massive sulphide) with similar Co (0.17%). The Ni content of the Moxie Pluton olivines document the fractional removal of sulphides during crystallization of the host magma, which resulted in the progressive depletion of the chalcophile metals in this magma. Modelling that involved the fractional crystallization of the magma coupled with the fractional removal of a specified proportion of sulphide has successfully duplicated the Moxie Pluton sulphide compositions. A similar magmatic model has been postulated for the Katahdin sulphides with a greater degree of sulphide fractionation. This latter model is again supported by extremely low Ni/forsterite ratios in olivines, though the compositional range is insufficient to document fractionation. These magmatic models are not unique, but they provide a relatively constrained and consistent explanation for the sulphide compositions.The Ni contents of olivines are the most important indicator of sulphide-silicate interaction in mafic magmas and have exploration potential. They provide a means of assessing the timing and extent of sulphur saturation in an intrusion and are a guide to the Ni content of a sulphide accumulation in equilibrium with olivine. In the Maine examples they provide strong evidence of the magmatic origin of the sulphide accumulations and justification for magmatic modelling."

Jan 1, 1984

By B. Denby

sintered ores, to be removed by a pneumatic,

Apr 1, 1995

By J. K. Brimacombe, F. D. Richardson

Studies have been made of interfacial turbulence occurring in reactions in which indium, zinc and cadmium, dissolved in amalgams, are oxidised into aqueous phases by ferric or mercurous ions. It has been found that this turbulence occurs when the concentrations of oxidising ions in the aqueous phase become sufficiently great. These concentrations are the same as those at which the mass-transfer coefficients in the aqueous phase increase sharply when both phases are stirred by gas bubbles rising through them. The effects of gas flow rate on the mass-transfer coefficients for zinc in mercury have been established, and the oxidation of pure mercury has been investigated. The relevance of the work to processes involving liquid metals is discussed

Dec 1, 1971

By T. T. Chen, J. E. Dutrizac, C. Canoo

The calcine consists principally of ZnO and ZnFe2O4, which occur as banded and porous grains, together with lesser amounts of Zn2SiO4, Zn-Fe-Pb silicate, sphalerite, quartz, PbSO4 and Fe2O3. Al is present in solid solution in most of the Fe-bearing phases and also as residual aluminosilicate minerals from the original concentrate. Si occurs mostly as Zn2SiO4, Zn-Fe-Pb silicate and as residual silicate minerals. As is commonly found in the ZnFe2O4, Fe2O3 and Zn-Fe-Pb silicate phases. The major As carrier may be calcium arsenate particles less than 1 micrometre in size which are dispersed throughout the calcine. The neutral leach residue consists mainly of ZnFe2O4 and precipitated masses of iron gel-silica gel. Lesser amounts of ZnO, Zn2SiO4, Zn-Fe-Pb silicate, PbSO4, sphalerite, Pb-K-jarosite and basic zinc sulphate are also present. Al occurs in minor concentrations in most of the Fe-bearing phases and in the Zn-Fe-Pb silicate. The residual aluminosilicates are also an important Al carrier. The major As carrier is the precipitated iron gel-silica gel phase, but some As is also present in the Zn-Fe-Pb silicate, ZnFe2O4 and Fe2O3 phases. Silicon is divided about equally between the iron gel-silica gel, Zn2SiO4, Zn-Fe-Pb silicate and residual silicate minerals. The weak acid leach residue is generally similar to the neutral leach residue except for its reduced content of ZnO and basic zinc sulphate.

Jan 4, 1993

By G. G. Lambert

The paper traces the pattern of spontaneous combustion in the workings of what was originally Hemsworth Colliery, but since July 1967 is now part of South Kirby Colliery. Examination is made of the Barnsley Seam sections and the part played by the top section of the seam as it comes in close proximity to the main seam. In this area of the colliery nine mechanised faces were set away between the years 1953 and 1968, every one "fired" at the pillar edge and six "fired" at the face line when production had ceased. The paper deals with the different preventative measures used, from sandbag walls, cement injections, spraying with polyurethane, until finally using Mandoseal as a sealant. Since the latter method was first used, the last three faces worked in this particular area were all salvaged completely, without any sign of a heating developing.

May 23, 1905

By S K. Das

An intensive investigation into modern roof support technology, including hy draulic and control systems, has been carried out against the perspective of global development and support behaviour on longwall faces across the Indian sub-continent. The wide ranging study examined various types and designs of modern supports used in seams of varying thickness and inclination where caving and stowing were practised. Consideration has been given to structural analysis, support resistance, the various forces acting over and on the powered supports and to support compatibility. The examination of the phy sical parameters has been allied to field experience and, together, have led to the formulation of standard designs for both the powered support structure and structural systems. A realistic mathematical model has been formulated for calculating the capacity of roof support requirements resulting from the actual behaviour of the immediate roof stratum. As a result of the work, it should be possible to readily select the most appropriate type of support sy stem for the conditions and longwall mining method that is to be employed.

Jan 4, 1997

By M. J. Russell, W. E. Stephens, D. B. Mohamad, A. B. MacKenzie

Redox front processes in rocks are important in the context of both radioactive waste disposal and the development of orebodies. Results are presented from a study of the distribution of uranium and thorium and the natural decay series equilibrium about redox fronts in a granite at the Criffel pluton and Craignair quarry, Dalbeattie in southwest Scotland. The results are considered in the context of large scale uranium aqueous transport in the region and compared with those from a previous study of highly developed redox fronts at Pocos de Caldas, Brazil. Results show that the Criffel pluton has experienced a recent and rapid removal of uranium from the uppermost section of the granite whereas thorium has remained relatively immobile. The radium and uranium distributions indicate that diffusion processes probably control the distribution of radionuclides about the front. These processes are similar to those observed at Pocos de Caldas. The trends of concentration and activity ratio about the Dalbeattie redox front are less pronounced than those at Pocos de Caldas owing to the shorter time available for the process and the lower intensity of weathering at Dalbeattie.

Jan 12, 1992

By J. E. Rouse, D. L. Buchanan

"During the emplacement of the Bushveld Complex in the Potgietersrus area magma reacted with the original floor rocks— Archaean granite or Malmani dolomite and overlying Penge handed ironstone or sedimentary rocks of the Pretoria Series. The complex sequence of sulphide-rich mafic rocks that formed along the contact is known as the Platreef. Associated with the sul­ phide mineralization are important concentrations of platinum-group metals, copper and nickel. Xenoliths of Malmani dolo­ mite have been incorporated into the Platreef and previous work has suggested that anhydrite is likely to have been present in the dolomite. The sedimentarv-derived sulphur thus introduced into the magma exercised an important control on the forma­ tion of the sulphides.Petrographic studies on the Platreef rocks from the Tweefontein area indicate that the original magma reacted with the banded ironstone to form iron-rich pyroxenites. In the Turfspruit area, to the south, the footwall rocks consist of sediments of the Timeball Hill Series. Original argillaceous rocks have been metamorphosed to cordierite-, corundum- and spinel-bearing hornfelses. Graphite was present in the contact zone in both the Tweefontein and Turfspruit areas. Anhydrite-bearing hornfels rocks are also present on Turfspruit.The Platreef rocks that overlie the corundum- and spinel-bearing hornfelses on Turfspruit are peridotitie, and pyroxenites are present in areas underlain by cordierite-bearing hornfels. The absence of orthopyroxene in the peridotite is probably indicative of low silica activity in the original magma. The pyroxenites have, however, undergone silica contamination from the underlying more siliceous cordierite hornfels.Carbon isotope studies indicate that the graphite in the Tweefontein and Turfspruit samples represents organic material orig­ inally associated with the footwall sediments. Sulphur isotope determinations on the anhydrite-bearing floor rocks indicate that this phase is clearly of sedimentary origin and was probably derived from an evaporitic unit within the carbonate sequence. This provides firm support for a model of ore genesis that involved the introduction of additional sulphur into the Bushveld magma. Isotope studies on sulphides associated with the banded ironstone and graphite indicate that these units were not the source of additional sulphur. Experimental studies predict, however, that a magma contaminated with iron- and carbon-rich material would have a high sulphur-carrying capacity. Where additional sulphur is available the magma would achieve saturation early in its crystallization history and precipitate an immiscible sulphide phase. Experimental work has also shown that sulphide precipi­ tation can be triggered by the introduction of salic material into a magma close to sulphur saturation. This mechanism probably played a role in the control of the sulphide mineralization in the Turfspruit area."

Jan 1, 1984

By A. Ludkin

The paper presents the history of the occurrence of spontaneous combustion in the north area, together with the associated problems. These are examined and a description is given of the methods used to combat the danger, including the use of modern scientific instrumentation. Detailed reference is made to the underground trials with pack injection and sealant coatings which were carried out at Seafield Colliery following the formation of a working group to assess the performance, in the same underground conditions, of (1) sandbagging, (2) pack injection, (3) surface coating. Based on these trials, an improved and more economical method of prevention has been established. There is, however, still scope for further improvement in techniques which would take into account the problems of gradient, transport, manpower and cost.

May 23, 1905

By B. Denby

Paper presented at a meeting on: Artificial intelligence in the minerals sector, held in Nottingham, UK, 20 April 1993. The design and scheduling of open pit operations are consistent problems encountered by the surface mining industry. Numerous techniques and algorithms have been developed to assist the mining engineer in the creation of optimum development strategies. Virtually all the practical techniques that have been produced have concentrated on one of the aspects (limit definition or scheduling) at the expense of the other. It has long been recognised, however, that the two activities are intrinsically linked and thus solving either problem independently of the other can only ever produce sub-optimal results as a whole. This has been termed the "circular reasoning problem". It has also been recognised that, for all practical-sized situations, solving both problems simultaneously is virtually impossible using conventional techniques due to the massive size of the search space involved. A technique is presented which is based on a self-learning genetic algorithm, which provides a combined pit limit and extraction schedule simultaneously in order to maximise the NPV (net present value) of the extraction. The theory is developed in two-dimensions and a number of examples of its application are presented. It is proposed that this approach is a highly efficient, heuristic technique offering the potential to transcend the circular reasoning difficulties of separate pit limit and extraction scheduling systems. Extension of the technique into three-dimensions and its application to realistic problem sizes are discussed

Apr 1, 1994