Search Documents

Two of the most important economies in coal-washing are in the actual washing of the coal and in a proper lay-out to reduce to a minimum the cost of labour for handling and washing. A guarantee is usually required for turning out a washed coal containing not more than 2% of free dirt and a resulting refuse with not more than 2% of free coal; any plant that gives results within such guarantees can he considered economical, provided that there are no other losses during the washing process. Various drainage arrangements and washery lay-outs are illustrated and discussed with respect to drainage, bunkers, sieves, settling tanks and conveyors and two further points considered: siding accommodation, which may become quite important with washeries of large capacity especially when the coal is brought in railway-wagons; and the irregularity with which the coal arrives. (Paper presented at the Manchester Geological and Mining Society's general meeting held in Manchester, April 11th 1916, with Mr. Leonard R. Fletcher, President, in the chair)

Dec 1, 1916

By R. W. Ruddle

The present state of knowledge on this subject may briefly be summarized as follows: (1) The copper content of the slag increases with the grade of the matte in contact with it; on the other hand, the proportion of copper lost decreases as the matte grade increases, because as a general rule a smaller volume of slag is produced when a high-grade matte is made. (2) The presence of CaO and MgO in the slag decreases the copper content of the slag, and the presence of ZnO increases it; the presence of A1203 seems to have little effect. The influence of the silicate degree is not yet clarified, but on theoretical grounds it seems likely that the copper content increases with the silicate degree of the slag. (3) High slag viscosity, high magnetite contents and low density difference between matte and slag all tend to increase the copper loss. The volume of slag is also an important factor. (4) The effect of bath temperature on the copper loss is not clear and further investigation of this point is needed. (5) It appears possible to recover a large part of the copper in the slag by adding FeS, CaS and other sulphides

Jan 1, 1953

By A. G. Royle

Sampling formulae for in-situ material, hard rock sampling and alluvial sampling are briefly discussed

May 1, 1991

By B. H. Smith

"Most of the discoveries of nickel sulphide deposits in Western Australia have followed the search for gossans. The chances of further discoveries depend on improving our understanding of the cover of strongly leached and transported materials that obscure approximately 85% of the area of the Yilgarn Block that has nickel sulphide mineralization potential. The lateritic profiles that are observed on the Yilgarn Block today were formed over a period of more than 100 m.y. of warm and humid climates. This lateritized land surface has been preserved by induration during subsequent arid climates as well as by the structural stability of the Yilgarn Block.In geochemical surveys of lateritied terrain samples have to be taken from at least the saprolite zone usually by drilling so that confident predictions can be made of the significance of analytical data. Account must be taken of the mineralogy of samples, as well as the nature of the horizon of a laterite profile that is being sampled, owing to the concentrating effects on trace elements of Fe and Mn oxides.Multivariate techniques have been applied successfully to analytical data in gossan recognition when textural evidence is ambiguous. Pathfinder geochemistry has also been used in gossan recognition and the most significant recent advance has come from studies of platinum group metals in nickel sulphides and their dispersion during weathering."

Jan 1, 1984

By C. A. Pickles

Mixtures of silver chloride and copper chloride are produced during gold refining by the Miller process. A study was carried out into the reduction with iron of a synthetic Miller chloride containing 13.64 mass% Ag and 2.42 mass% Cu. The effects of smelting temperature and time and of additions of iron and borax were investigated. The results were interpreted in terms of metal recovery and quality. Temperature did not have a significant effect on metal recovery above the melting point of the metal product. Borax additions reduced vapour losses and improved metal recovery. With excess iron it was possible to achieve silver recoveries of about 100% and copper recoveries of about 70%. The metal product contained on average 76.1 mass% Ag, 7.5 mass% Cu and 12.8 mass% Fe.

Jan 4, 1993

By A. D. Read

Selective flocculation was investigated as a possible method of recovering values from mineral slimes which are too finely divided to be treated by conventional mineral processing methods. It has proved possible to flocculate selectively either haematite or a silicate from a stably dispersed mixture by varying the anionic character of the high-molecular-weight, partially hydrolysed polyacrylamide employed. Different separation methods have been developed for hard and soft water media. Electrokinetic and infrared techniques have been employed to elucidate the mechanism whereby selectivity has been attained in the different cases. The following influences on the various selective flocculation parameters have been investigated: (a) the level of the different reagent additions and (b) the shear conditions during and after flocculant addition. A feature of the particular system studied was the high solids content at which it was possible to achieve good selectivity. Probable reasons for this are advanced, and the possibilities and potentialities of the process are discussed.

Dec 1, 1971

By L. D. Smith

Paper presented at the conference: Risk assessment in the extractive industries, held in Exeter, UK, 23-24 March 1994, and first published London: IMM, 1994, preprint volume. 22pp., 15 refs. The concept of risk is well established in the mining industry but it is difficult to provide a quantitative assessment of risk. A discussion is presented of the significant sources of risk in a mineral project and how they are addressed. The discount rate is examined as a fundamental means of reflecting risk in discounted cash flow evaluations. Current industry practice is discussed and a methodology for the analysis of risk levels is proposed which assesses the constituent components of the discount rate (real interest, mineral project risks and country risk)

Dec 1, 1994

Further discussion at the North of England Institute of Mining and Mechanical Engineers' general meeting held in Newcastle-upon-Tyne, 3rd June 1916, on the paper published in Trans. I.Min.E., vol.L, 1915, p.179, consisted of the author's written response to Mr. Hare's comments at the April meeting

Dec 1, 1916

By P. A. Rossouw, G. A. Fourie

The correction to the paper published in Trans. IMM A, vol.105, 1996, p.A162-A165 stresses that figs. 4 and 5 had been interchanged, reproduces them with their correct captions for clarity and encourages readers to comment on the Delft proposal

Jun 19, 1905

Paper presented at the conference Risk assessment in the extractive industries, held in Exeter, 23-24 March 1994. Sensitivity analyses based on financial variables are now routinely applied to the forecast financial results of mining projects especially during the feasibility stage. Risk analysis is gaining acceptance but is still almost universally confined to the effects of variations in financial variables. The single most sensitive factor in almost all mining projects is the ore reserve, but it is either ignored or improperly used in sensitivity and risk analyses. Unlike financial variables, the components of the ore reserve (grades and tonnages of mining blocks) are a function of location within the orebody. Physical (mining) access to these components is therefore a function of time which has a crucial effect on forecast cash flows. It is critical that these fundamental concepts are included in risk analyses of mining projects. The effects are considered of the uncertainty of the ore reserve on feasibility studies and open-pit mine design for a small gold mining venture. Geostatistical simulation is used as a method of quantifying the risk in using grades and tonnages estimated from sparse data

Jun 16, 1905

By R. J. Pine

Procedures are described for the application of risk analysis or probabilistic methods to mining geomechanics. The methods are widely applicable to existing mine design models. Detailed examples are given of plane slope failure and of pillar design based on displacement-discontinuity stress modelling and empirical strength assessment. The modelling techniques assessed are the Latin hypercube sampling method, incorporated in a spreadsheet environment, and the general point estimate method (GPEM), programmed in TurboBasic. An example GPEM program listing is included. Both methods are very convenient to use. Probabilistic acceptance criteria for slope stability after Priest and Brown are examined and alternatives are proposed where output distributions of factor of safety are approximately normal or lognormal and output distributions of safety margin are normal. The reliability index is included as a useful measure of variability with proposed acceptance criteria.

Jan 12, 1992

By Z Hu

The technique of reclaiming disturbed land by use of a hydraulic dredge pump (HDP) (which is a set of hydraulic machines for earthwork), termed 'digging deep to fill shallow has been used in the reclamation of subsidence areas in Chinese coal mines. This paper discusses the operational principle of the technique and summarises its reclamation procedures, which are being used in current reclamation practice. The soil condition reclaimed by the HDP was studied. The results showed that the pioneer crops to be planted in the reclaimed soil should be the ‘pulse’ family crops, and that improvements to the reclaimed soil and the HDP technique itself are needed. Bused on the analysis of the previous technical processes, a new rational technical model for the HDP reclamation method is presented in this paper.

Jan 4, 1996

By G. D. Nicholls

There have been very few attempts to isolate the various factors that contribute to the overall imprecision of geochemical analytical procedures, due in part to the difficulty of distinguishing between them. The technique of spark source mass spectrography permits a ready distinction between the contributions to overall precision from sampling error and instrumental and other errors. With conventional methods of sample preparation for this technique sampling difficulties are responsible for 80-90 per cent of the overall imprecision. Examination of the probable location of the major difficulties in sample preparation indicates that the preliminary stage of grinding, mixing and extraction of a first aliquot (about 1/100 of the original sample) is generally perfectly adequate. The difficulty lies in the subsequent stages of sample preparation. Dry mixing techniques are unlikely to give good precision if the sub-samples actually examined by the analytical technique are less than 10 mg in amount. Solution techniques are less prone to sampling difficulty. Fusion techniques, unless conducted with great care, can produce more difficulty than dry mixing. Sample preparation is critical to the success of many analytical procedures. Selection of appropriate sample preparation techniques requires just as much care as the selection of techniques for the actual analysis.

Dec 1, 1971

By G. G. Lambert

The paper traces the pattern of spontaneous combustion in the workings of what was originally Hemsworth Colliery, but since July 1967 is now part of South Kirby Colliery. Examination is made of the Barnsley Seam sections and the part played by the top section of the seam as it comes in close proximity to the main seam. In this area of the colliery nine mechanised faces were set away between the years 1953 and 1968, every one "fired" at the pillar edge and six "fired" at the face line when production had ceased. The paper deals with the different preventative measures used, from sandbag walls, cement injections, spraying with polyurethane, until finally using Mandoseal as a sealant. Since the latter method was first used, the last three faces worked in this particular area were all salvaged completely, without any sign of a heating developing.

May 23, 1905

By P. Seppanen

Cemented fill was first introduced at the Keretti mine in 1952, but entailed high cement costs, the need for stope preparation, slimes handling, clean-up and maintenance, increased mine dewatering, segregation of fill and long setting times. In the 1970s research began into the use of iron blast-furnace slag as a binding agent and by 1989 Pyhasalmi, Vihanti, Keretti, Vammala and Enonkoski had saved US $11 000 000 by using slag binders instead of cement. Viscaria in Sweden and Tara in Ireland also use slag as 90-100% of total binder, although their backfilling methods vary. The main area of interest in slag research is determining the activation methods for initiating the binding reactions; it is also important to achieve other characteristics such as resistance to corrosion by sulphuric ion. New backfilling techniques developed during the 1980s included the use of high-density cemented tailings fill at Vammala and porous cemented rockfill at Enonkoski and Viscaria. Future developments focus on concepts such as integration of mining and milling with backfilling and the achievement of total underground disposal of wastes

Dec 1, 1995

By C. C. Harris

The use of Alyavdin's equation Y(x,t) = 1-e(-bt) for describing the effect of grinding time on size distribution is discussed. The equation transforms into linear form by expressing it as log-log reciprocal (1 - Y) versus log t. For plotting, specially divided grids are available; Rosin-Rammler or Weibull charts may be used. The data of Herbst and Fuerstenau are especially useful for illustrating the Alyavdin-Weibull chart in two applications: (1) presenting data (which are relatively unaffected by experimental scatter) and comparing them with theoretical predictions, and (2) as a test for the zero-order kinetics production hypothesis. The chart based on the Alyavdin-Weibull equation is suggested as a useful aid in the analysis of kinetic data (/ versus f), though not as a procedure in its own right. Proposed applications are (1) displaying data with excellent clarity, since it avoids the kind of congestion inherent in some other plotting methods, and (2) as a test for assumed kinetic relationships. Sometimes, equation 1 describes the data quite closely, and in these cases the parameter values appear to be related to certain operating conditions.

Dec 1, 1971

By J. Coxon, G. W. Walker

The paper describes the discovery, location and events concerning three types of heating which have occurred in recent years: a) in a district being salvaged, b) in the shaft pillar at an air-crossing, and c) in the gate side of a production district, all of which have occurred in the Beeston Seam at collieries in the deeper eastern part of the area. The paper describes the precautions, air sampling arrangements, training methods and codes of practice which have been adopted at collieries where spontaneous combustion is, or is likely to be, a hazard. The air samples taken from behind the stoppings following the sealing off of the salvaging district are examined and interpreted. The problem of effectively sealing off where more than two stoppings are required is made apparent. Other lessons have been learned as a result of these heatings and are described in the paper.

May 23, 1905

Discussion of the paper presented at the Manchester Geological and Mining Society's general meeting held in Manchester, April 11th 1916, with Mr. Leonard R. Fletcher, President, in the chair, included questions asked and points for discussion raised by Bramall V., Paton J.D., Fletcher L.R., Siddall F.N., Stoker A. and Stone T., in particular on how to eliminate dust

Dec 1, 1916

By S. Y. Ezz

Report of discussion at February, 1971, IMM general meeting (Chairman : M. J. Cahalan, President) of a paper published in Transactions/ Section C (Mineral Processing & Extractive Metallurgy), vol. 79, September, 1970, pp. C226-C233 with contributions by Wild R. and Astier J. on fluidised bed reduction of iron ore fines

Dec 1, 1971

By Blatchford A. S.

Discussion at the North of England Institute of Mining and Mechanical Engineers' general meeting held in Newcastle-upon-Tyne, 3rd June 1916, on the paper published in Trans. I.Min.E., vol.LI, 1916, p.361-377, comprised written comments by Ashworth J. on the practicality of applying quenching materials to a dust cloud ahead of the explosion flame

Dec 1, 1916