Search Documents

During the construction of storage caverns, and during their lifetime if the use to which they are put so requires, it is necessary to provide adequate ventilation to ensure the safety and comfort of the underground workforce. An analysis of likely contaminants during construction has indicated that where a large facility is situated in a rock mass of even moderate temperature climatic conditions are likely to be the limiting factor during most of the mining operation and atmospheric pollution when blasting is undertaken. Possible options for improvement are increased air flow, cooling of intake air and reduction of the heat source by altering the number and type of haulage units employed in the cavern. Local solutions are an alternative approach where heat problems are confined to a few specific locations

Aug 1, 1994

By G. R. Doughty

It is shown that sodium can be removed very readily from molten aluminium by the use of a beta"-alumina, the more highly conducting form of beta-alumina, provided that the surface of the tube is wetted by a layer of salt. From current/time plots the theoretical amount of sodium removed has been calculated and excellent agreement obtained. The beta"-alumina tubes can be immersed directly in the Al without fracturing if they are pre-heated for a few minutes prior to immersion. According to its stability beta"-alumina should be attacked by molten Al at low Na contents, but in these experiments the salt acted as a protective layer. Magnesium chloride is a relatively cheap salt, whose Mg product can be used within a foundry. The only other product is NaCl, which can be used in-house as a flux or sent for disposal. No polluting gases are used or produced and no drosses created. The time for removal of sodium was quite short, comparable to that for chlorination

Jun 21, 1905

By A. F. Neil, A. S. Bahaj, P. Watkins, P. M. Hyslop, C. E. Kirby, P. A. B. James

The results of initial work indicate that for 3 of the 5 quarry sands bioleaching reduces the iron oxide content to a commercially acceptable 0.035 wt% Fe20 3, although the time taken to achieve this is 14-22 days against a target leach time of 7 day. Subsequent work has identified strains of Aspergillus niger that are more efficient at producing the array of complexing agents for iron and is yielding excellent and rapid reductions in Fe levels. Potentially, bioleaching offers a more environmentally friendly and energy-efficient process for the removal of Fe from glass-making sands than conventional routes but the production of organic acids by fermentation must be achievable with low-cost substrates such as sugar-beet molasses and lactose permeates for bioleaching to offer a commercially viable alternative to treatment with hot mineral acids. Silica sands usually contain three groups of Fe minerals: iron oxyhydroxides, which comprise crystalline types such as goethite and limonite tending to occur as thin, discontinuous coatings and in cracks and crevices on the surface of the quartz; the assemblage of heavy trace minerals, which include ilmenite, rutile, leucoxene, chromite and haematite, commonly present at levels of 0.1 wt% or less as discrete grains or sometimes cemented to the quartz; and clay minerals cemented in pits on the surface of the quartz and in association with weathered, discrete feldspars. The response of the assemblage of iron minerals to short periods of exposure to hot inorganic acids is broadly related to which group they belong to, those that form coatings being accessible to acid and tending to react rapidly whereas the trace minerals are usually resistant and react very slowly, if at all, and the clays are probably digested. The note reports on a preliminary study of the use of microorganisms to develop an alternative clean technology that will give results comparable to those achievable with hot inorganic mineral acids but with more environmentally acceptable procedures. Various fungi and bacteria produce organic acids when grown in certain media. When these acids come into contact with Fe-stained sand grains the iron is removed as soluble complexes. Several strains of Aspergillus niger have been found to produce organic acids from sugar, predominantly citric, gluconic and oxalic acids, their relative yields depending on cultivation medium and conditions. Sand samples were prepared from five quarries in the UK: Levenseat, Lothian; Redhill, Surrey; King's Lynn, Norfolk; Chelford, Cheshire; and Oakamoor, Staffordshire; ranging in iron oxide content from 0.035 to 0.153 wt% Fe203

Jun 18, 1905

By A. J. Beer, A. Wetherelt

Paper presented at the UK minerals industry conference held in Leeds, UK, 3-5 April 1995. Camborne School of Mines has developed a simple, cost-effective light-sectioning method that has been used successfully in tunnels and small stopes. Light sectioning provides an almost visual examination of the stope's excavated profile. An illuminated section of walls, roof and floor is recorded photographically. Overbreak and underbreak can then be easily quantified by reference to the designed shape. The prototype rig is described. Use of a fish-eye lens to capture a greater field of view is discussed. Calibration was achieved by comparison with images made with a conventional wide-angle lens with nominal distortion. The system is reliable under a range of operating conditions including dust, heat and humidity. It is also simple and easy to use, does not require skilled personnel and is low cost

Jun 18, 1905

By A. D. Read

Selective flocculation was investigated as a possible method of recovering values from mineral slimes which are too finely divided to be treated by conventional mineral processing methods. It has proved possible to flocculate selectively either haematite or a silicate from a stably dispersed mixture by varying the anionic character of the high-molecular-weight, partially hydrolysed polyacrylamide employed. Different separation methods have been developed for hard and soft water media. Electrokinetic and infrared techniques have been employed to elucidate the mechanism whereby selectivity has been attained in the different cases. The following influences on the various selective flocculation parameters have been investigated: (a) the level of the different reagent additions and (b) the shear conditions during and after flocculant addition. A feature of the particular system studied was the high solids content at which it was possible to achieve good selectivity. Probable reasons for this are advanced, and the possibilities and potentialities of the process are discussed.

Dec 1, 1971

By G. Richards

Following on from the article in Materials World February 2015 (Asset 997) this article is the second half of a special focus on graphite. It looks at graphite's market prospects over the next few years. Natural graphite is used in refractories, which accounts for ca. 20% of global demand and is forecast to grow by 2-4%/a to 2020, while the largest growth in demand (increases of 10-15%/a) is estimated to come from its application in anodes for lithium-ion batteries, especially those in hybrid electric vehicles. High-grade natural graphite deposits that are either coming back on stream or are in the pipeline are discussed including Woxna mine in Sweden, Bissett Creek project in Ontario, Canada, Balama mine in Mozambique and Lac Knife project in Quebec, Canada

Mar 1, 2015

By T. Guerin

More than 370 million litres of oil leak from hydraulic equipment every year, excluding all other sources of plant fluid losses. This item analyses the causes of fluid spills from plants and equipment on resource construction sites, and offers some possible solutions.

Apr 1, 2015

By C. C. Harris

The use of Alyavdin's equation Y(x,t) = 1-e(-bt) for describing the effect of grinding time on size distribution is discussed. The equation transforms into linear form by expressing it as log-log reciprocal (1 - Y) versus log t. For plotting, specially divided grids are available; Rosin-Rammler or Weibull charts may be used. The data of Herbst and Fuerstenau are especially useful for illustrating the Alyavdin-Weibull chart in two applications: (1) presenting data (which are relatively unaffected by experimental scatter) and comparing them with theoretical predictions, and (2) as a test for the zero-order kinetics production hypothesis. The chart based on the Alyavdin-Weibull equation is suggested as a useful aid in the analysis of kinetic data (/ versus f), though not as a procedure in its own right. Proposed applications are (1) displaying data with excellent clarity, since it avoids the kind of congestion inherent in some other plotting methods, and (2) as a test for assumed kinetic relationships. Sometimes, equation 1 describes the data quite closely, and in these cases the parameter values appear to be related to certain operating conditions.

Dec 1, 1971

By S. V. Shiraishi, H. B. Bell

Report of discussion at February, 1971, IMM general meeting (Chairman: M. J. Cahalan, President) of a paper published in Transactions/Section C (Mineral Processing & Extractive Metallurgy), vol. 79, June, 1970, pp. C120-C127, with a contribution by Wright P.A. on the miscibility gap

Dec 1, 1971

By N. Powell, R. J. Pine

An algorithm is proposed for updating the probability of slope failure on the basis of sequential testing using Bayesian probability theory. The approach is novel and computationally straightforward since, unlike other methods, updating of the probability of failure is carried out directly. This is because the probability is treated as a random variable whereas other methods have considered it as a purely deterministic value or as a function of shear strength parameters that are updated individually. The prior information required for the Bayesian analysis is obtained by a conventional probabilistic analysis. An exponential distribution is then used for the probability of failure, applying the principle of maximum entropy. This distribution is continually updated for individual slope cells, where repetitive excavation creates several such cells and a corresponding series of Bayesian estimates of the probability of failure is obtained. The approach is applicable to most simulations but there are limitations on its use. A more mathematically rigorous refinement using the beta distribution is currently under development

Apr 1, 1996

By R Lastra, J. A. Finch

An artificial standard material has been developed and used to examine the robustness of some of the procedures for correcting stereological bias. Different mineral liberation distributions were constructed from the standard material. The particles were mounted, sectioned and the sectioning data measured with an electron microscope interfaced to an image analyser. Four correction procedures were used and the corrected and true liberation distributions compared. It was found that the large-sections correction provided a simple, uncorrupted correction. Hill's fast approximation performed well except in cases of narrow liberation distributions; the sectioning data appeared to support the assumption that the locked section and locked particle distributions are identical. Barbery's correction performed well in most cases, having difficulty only with the very irregular liberation distribution. The PARGEN correction was able to provide a good estimate of the true amount of free material, but had difficulty in predicting the locked particle distribution

Jun 21, 1905

By Jones R. G.

Dr Pat Foster, Senior Lecturer in Mining Engineering at the UK's Camborne School of Mines, talks to Rhiannon Garth Jones about mining safety around the world, education and the future of the industry

Feb 1, 2015

By Fearnsides W. G.

The second part of the paper, presented at the Midland Institute of Mining, Civil and Mechanical Engineers' general meeting held in Doncaster on 27th May 1916, addresses the post-Carboniferous and pre-Permian movements which brought about the partition of the area and gave to the North Midland district its individuality as a separate coalfield. As earth-movements of several ages subsequent to the Carboniferous have played a part in the formation of this particular coalfield, the aim is to elucidate the effects which belong to the post-Carboniferous and pre-Permian Period and to disentangle them from those of later date. This is done by comparing the geometry of the folded surface of one of the more important horizons in the Coal-Measures with that of the surface of unconformity which divides the Permian from the Carboniferous rocks in South Yorkshire, Derbyshire, and Nottinghamshire

Dec 1, 1916

By P wade

This is the first Presidential Address given to the Nottinghamshire Branch of The Institution following the merger of the Nottinghamshire and North Derbyshire Branch of The Institution of Mining Engineers (IMinE) and the Midland Branch of The Institution of Mining Electrical and Mining Mechanical Engineers (IMEMME). I intend to review the formation of the individual institutions as well as what has been achieved by mining related institutions over the years and finally I intend to look to our future.

Jan 11, 1996

By A. L. W. Lips, B. P. J. Stevens, T. J. R. Barclay, E. Rothery, S. H. White

Discussion by B.P.J. Stevens of the paper, published in Trans. IMMA, vol.104, 1995, p.B1-B17, is presented together with the authors' response. Stevens questions the authors' radically different interpretation of the structural geology of the Broken Hill Block, considering that the descriptive part of the paper is a useful addition but that the conclusions are unwarranted on the basis of the data presented. A number of major points of disagreement are outlined and half a dozen additional minor points listed. In response, the authors admire Stevens's contribution to unravelling the geology of the area but defend their attempts to take the regional studies a step further, pointing out that he has misquoted what they wrote and arguing that because of the assumptions underpinning the derivation of the present stratigraphy it cannot be used to constrain structural models. With regard to shear zones, they cite the extensive earlier literature and refer to horizontal displacements shown on maps produced by Stevens et al. Detailed discussion follows of the stratigraphy and of the stratigraphic correlation problems resulting from failure to recognise the presence and significance of shears, particularly those parallel to stratigraphy. The remobilised position of the Pb mineralisation in the North Mine open cut is reiterated. It is concluded that there is an urgent need for systematic isotopic dating in the area to constrain the stratigraphy

Apr 1, 1996

By B. D. Rayment, J. D. Wilson, G. R. Davis

Wheal Jane, situated between Truro and the Carnmenellis granite, is under development by Consolidated Gold Fields, Ltd., as a tin producer. The main or B lode comprises a complex cassiterite-sulphide ore located in shear zones along the footwall of the lowest of a series of porphyry dykes (elvans) which strike ENE and dip 35° north. Minor mineralisation follows other elvan contacts and sets of later steeply dipping fractures. The localisation and overall geometry of the deposit is explained in terms of the complex structural geology of the Lower Palaeozoic metasediments and the shape and manner of emplacement of the invading Hercynian granite of Cornwall. Variations in the thickness and grade of the orebody, and in the nature of the mineralisation, are shown to be structurally controlled by undulations of the footwall contact of the B elvan. Wallrock sericitisation is present and is applied in exploration for ore

Dec 1, 1971

By Li Shibo, C. Halls

The compositions of olivine, pyroxene and chromite from the Proterozoic ultramafic complex are analagous to those of cumulate ultramafic rocks of tholeiitic origin, suggesting that the parent magma may have been tholeiitic rather than komatiitic. The complex contains economically significant Ni-Cu sulphide mineralisation. The high sulphide/silicate ratio is best explained in terms of the segregation of sulphides from a large volume of magma, of which all but the ultramafic cumulate fraction has since been eroded. Platinum-group minerals that have been identified include sperrylite, moncheite, native platinum, froodite, merenskyite, michenerite and Pd-rich pentlandite lamellae exsolved from pyrrhotite. They are characteristically found in close association with chalcopyrite, either along the contacts between hydrosilicate and sulphide grains or in cracks within pentlandite and chalcopyrite, which may also be intergrown with galena. Crystallisation from a Cu-rich residual magmatic liquid also enriched in Pt, Pd, As, Sb, Bi, Te, Zn and Pb is postulated.

Jan 12, 1993

By A. M. Tunstall

Aspects of blast vibrations, damage mechanisms and the influence of rock quality on damage severity are reviewed and results presented from a monitoring programme in which the rock mass rating for six tunnels was determined. The peak particle velocity induced in the tunnels during open-pit blasting was measured and the tunnels were inspected visually for fresh damage after each blast. The results suggest that the quality of rock in which an excavation is situated has an influence on the level of ground vibration to which it can be subjected without sustaining damage. This means that the use of a single limiting value of peak particle velocity, as in the blast damage criteria for residential structures, is not ideal and may result in damage to excavations in poorer-quality rock masses

Jun 19, 1905

By J A. Hacked

This paper explores the potential to exploit controls over the outputs of the primary blasting operation, arising from the performance consistency benefits gained in using modern bulk emulsion explosives technology. The former, allied with the latest powerful blast predictive software and measuring tools, offers the user the opportunity to apply control over both cost and performance, which has not been possible in the past.

Jan 12, 1997

Discussion of the paper presented at the North Staffordshire Institute of Mining and Mechanical Engineers' general meeting held in Stoke-on-Trent, March 27th 1916, with Mr. John Gregory, President, in the chair, included contributions by Gregory J., Cadman J., Hartley J.W., Wain E.B. and Henshaw A.M., followed by the author's reply

Dec 1, 1916