Search Documents

By Lawrence W. Gubbe

Air blast associated with detonation of explosives in mining, construction or military applications is often responsible for complaints by people who live or work in the vicinity of the activity. Most often, the complaints are based on the perception that vibration caused by the airblast damaged one or more residential buildings that may be located within several hundred feet or several miles from the blast site. The potential for airblast to cause damage is related to the amplitude and frequency of the airblast overpressure wave at the receptor. Amplitude and frequency of the overpressure wave are, in turn, dependent upon the type and amount of explosive detonated; the degree of confinement; the distance the wave travels; the topography between the blast site and the receptor; and, atmospheric conditions. It is well known that, as the result of atmospheric focusing, the amplitude of airblast overpressure that exists relatively far from the blast site may be substantially higher than the amplitude associated with the attenuated wave in an isotropic atmosphere. Two methods are available to predict baseline overpressures 1) the Sandia Laboratories, Atomic Energy Commission method as extended by the Naval Ordinance Laboratory (NOL method) and the Ballistic Research Laboratory method (BRL method). These methods are developed by different techniques, are based on different idealized atmospheres and predict widely different results. The amplification factor applied to account for the effect of focusing must be consistent with the method used to predict the baseline overpressure. Theoretically, the amplitude of the overpressure at distances several miles from the blast site could be more than 25 to 100 times the amplitude of the attenuated wave predicted by the BRL method. However, based on comparisons with measured overpressure data is probably less than approximately 3 times the amplitude of the attenuated wave as predicted by the NOL method. This paper is based on research conducted as part of investigations of airblast damage complaints associated with an accidental explosion near Eveleth, Minnesota and with the disposal of military explosives by detonation at the Sierra Army Depot near Herlong, California. The techniques available for estimating the airblast overpressure that might be generated at various distances from the blast site and criteria for evaluating the potential for damage are examined.

Jan 1, 2004

By Brian Wingfield, Greg Williams, Richard W. Givens

Application of required energies into the rig design can have a dramatic impact upon productivity. Computer modeling of these production variables has led to changes in design with values closely approaching actual field data. Knowledge of these required energies can also specify the proper drilling technique to the application. With this knowledge, productivity-to-cost ratios can be determined with the most efficient option chosen.

Jan 1, 1995

By Jessie L. Bonner, W. Stephen Blomberg, Mark Leidig, Heather Hooper

Understanding the effects of the bench on ground motion can improve the design of cast blasts and achieve improved blast efficiency while remaining below vibration requirements. A new dataset recorded in September 2003 from a coal mine in Arizona has allowed us to examine the excitation of short-period Rayleigh-type surface waves from four simultaneously-detonated explosions in and below a topographic bench of a mine. The explosions were recorded on a network of over 150 seismic sensors, providing an extensive understanding of the ground motion radiation patterns from these explosions. We detonated two separate explosions (~3 tons and ~1.5 tons ANFO) in the deepest pit of the mine, thus the explosions were shot to solid rock. Within 25 meters of these two explosions, we detonated two additional explosions of similar explosive yields in a bench, thus these explosions were shot to the free face. Radiation patterns and spectral ratios from the explosions show increased amplitudes (by a factor of 1.5 to 2) at azimuths behind the bench relative to the amplitudes in front of the bench. We compared these findings to seismic observations from two ~1.5 million pound cast blasts at the same mine and found similar radiation patterns. Modeling of these blasts shows that the variations in ground motion are caused by the topographic bench as a result of 1) horizontal spalling of the rock falling into the pit and 2) non- linear scattering near the free- face. We also note that shooting to a buffer (previously blasted rock) causes the azimuthal variations to be significantly reduced.

Jan 1, 2005

By Braden Lusk

This paper includes results from analysis of recorded Acoustic Responses of Structures to Blasting. The analysis was performed to determine specific characteristics of sounds experienced inside homes during blast events. Data was collected in a typical house within the Boone North No.2 Coal Surface Mine in Ashford, WV which was instrumented for several blast vibration and acoustic responses. The instrumentation consists of four acoustic microphones distributed throughout the internal areas of the house and three geophones buried near the house. Two additional channels collect the trigger signal and Air Blast information. For each blast event recorded by the system, the mine blast reports were used to obtain major blast characteristics such as distance from the blast to the instrumented house, weight of explosive used, number of boreholes, delays, and other important parameters. This information allowed study the relationship between the acoustic response and the blast design. From a database of 43 records, five records were chosen for complete analysis. These records were chosen based on distance from the blast to the house, and specific blast parameters. This paper presents the result of the relationship between the frequencies and amplitudes for the entire trace of acoustic records, the response due to ground vibration (GV), and the response due to air-blast (AB). Frequency content was obtained through Fast Fourier Transforms (FFT), using D-Plot software. The records have a typical shape that permits cutting and analyzing each part of the signal with respect to GV and AB separately. Some conclusions are reported concerning the relationship between blast parameters and acoustic response of structures.

Jan 1, 2009

By Ian Bell, Saman Nouranian, Shahram Tafazoli, Bahram Sameti, Mahdi Ramezani

"Image-based rock fragmentation sensing in mining and quarry applications includes an important rock boundary delineation step, which is commonly referred to as rock segmentation. This paper presents a novel approach to solve this problem, using artificial intelligence. In the proposed technique, priorknowledge of previously analyzed images is encoded into mathematical/statistical models. A set of human labeled images are used as training inputs. These images are used to train neural networksthrough an optimization process. The networks can then be used in real time for rock delineation. "

Jan 1, 2017

By Tapan Goswami, Geoff Keith

"At Bulga Coal, the objectives of drilling and blasting are to maximise safety and to minimise the totalcost of mining. A recent audit of two overburden blasts established that the standard of drilling and blasting is excellent. No apparent hazards were identified. Laser profiling showed that highwall free faces are reasonably planar with some exceptions, thereby promoting uniform burden distances along front-row charges. However, in three isolated areas along one face, small burden distances existed. The mean and the standard deviation of errors in the collar positions of front-row blastholes was found to be 0.3 + 0.03 m. A borehole video camera was used to show that blastholes did not feature open bedding plane partings, cavities or damage produced by the blast in front of them."

Jan 1, 1999

By Tony A. Rorke, Joe R. Brinkmann

The application of instrumentation to better understand and improve production blasting is one of the most fruitful areas of explosives and blasting research. The majority of instrumented studies of production blasting have relied on the extrapolation of far field measurements to postulate blast performance in regions of interest closer to the charge where rock breaking takes place. However, the nonlinear and dissipative nature of the quantities being measured raises serious questions as to the accuracy and validity of such extrapolations.

Jan 1, 1991

By Gordon K. Jorgeonson

Much of the modelling of blasting operations has been devoted to simulating blasts in open pit mines and quarries . This has been the most obvious application and has been reported in many papers and discussions in the past.

Jan 1, 1990

By Ray Jambakhsh, Gabrielle Bourget

In the summer of 1998, Ontario Hydro awarded a contract to demolish an obsolete and inefficient chimney by blasting. The Ontario Hydro Thunder Bay Thermal Generating Station (T.G.S.), is a fully operational hydro thermal generating station located in Thunder Bay, Ontario, Canada. The Chimney was a 356 ft (108 m) high freestanding structure constructed of reinforced concrete with a brick liner. Falling the chimney required careful planning due to the highly sensitive structures and equipment which surrounded it. Damage either sustained to the existing systems through ground vibrations or direct contact would have resulted in expensive power outage and/or lost production. The role of Explotech Engineering Ltd. on this project was to provide and evaluation of the proposed demolition procedure, defme the predicted and maximum seismic vibrations at sensitive structures including underground services, conduct pre-blast / post-blast inspections and recommend various safety precautions. The general contractor for the project, LeBrun Northern Contracting Ltd., of Thunder Bay, Ontario was responsible for all site preparations and post-blast clean up. All demolition blasting calculations and operations were conducted by Dykon demolition experts from Tulsa, Oklahoma. On September 13, 1999, the chimney was successfully demolished. Extensive analysis of the vibration records and visual post-blast inspections of the surrounding structures concluded that the demolition event induced no damage to any of the Ontario Hydro facilities.

Jan 1, 2000

When a company has an effective hearing loss prevention program, everyone wins-the employers, the employees, and the safety and health professionals who implement the program. This guidebook is not about minimal programs that meet only the letter of the law. It is concerned with programs that are effective as well as efficient: those optimizing program elements that succeed in preventing hearing loss in a practical and cost effective manner.

Jan 1, 2006

By R. Singh, M. Roy, D. Singh

Success of a blasting pattern in Blasting-off-the-solid (BOS) in Bord (Room) & Pillar method of coal mining is judged by the percentage of pull achieved vis-à-vis the yield of coal produced in a blasted round. Improper blast design and distribution of explosives in shot holes normally causes poor breakage i.e. a major portion of shot holes left unbroken resulting into reduced yield per blast. Over and above the disturbance to the roof is also due to excessive vibration caused by explosive energy not properly utilized in fragmentation.

Jan 1, 2003

By Paul Downing

Anyone in business today knows how difficult and time consuming it is to keep abreast of new and revised federal regulations. Those in the explosives industry know that such a task can be next to impossible as the regulatory environment faced by those in the hazardous materials community continues to undergo a major overhaul following the events of September 11th, 2001. This paper will attempt to clarify today’s regulatory picture by identifying some of the regulatory “hotspots” and “pitfalls” that affect individuals and companies involved in the sale, transportation, distribution and use of explosives.

Jan 1, 2003

By S. Behera, K. Dey

This paper presents a methodology for finite element (FE) modelling to analyse the total deformation of rockmass under blast-load, with a focus on predicting backbreak that may occur during surface blasting operations. Backbreak can result from improper use of explosive energy, leading to damage beyond the excavation zone and jeopardizing operational safety and productivity. The paper highlights the impacts of backbreak on bench stability, excavator operation, drilling operation, flyrock generation, and improper fragmentation and boulder formation in surface blasting. However, prior estimation of extent of rock breakage zone can provide an idea to formulate the blast design to control the backbreak. While vibration-based prediction models are commonly used to estimate backbreak, they require physical blasting experimentation. To overcome this limitation, the paper describes the development of a FE model using ANSYS Explicit dynamics, which simulates rock blasting and calculates the total deformation of the rockmass. The rockmass deformation is modelled using Drucker-Prager (D-P) strength model with the Jones-Wilkins-Lee (JWL) equation of state for the explosives. The accuracy of the FE model is evaluated through physical experiments, and the results are compared with the vibration models. The FE model demonstrates close proximity to physical observations as well as vibration model result in predicting backbreak, thereby offering a promising alternative to vibration-based prediction models. The primary objective of the study is to predict the response of the insitu rockmass to explosive blast loading and determine the effective rock breakage zone.

Jan 1, 2024

By Alain Duchesne, Dominique Fonfrede, Alan Broca

The technique involves the removal, in one piece, of an unwanted concrete pile section, exploiting the principle of crack propagation induced using gas pressure. The device, or pod, is made of a container in which an over-pressure is generated. After a predetermined time delay of 72 hours, gas and pressure are produced by the reaction between a calcium base chemical and water.

Jan 1, 2012

By Andreas Bienz

The safety of persons from accidental explosions and fires during manufacture, storage, transport etc. of explosives, pyrotechnics, propellants, firework and ammunition is most commonly assessed according to prescriptive rule-based approach: Safety is given when all requirements which are listed in numerous regulations and directives (such as e.g. safety distances, limited quantities, protective installations etc.) are complied with. Such a deterministic prescriptive rule-based approach is quite easy to apply but has got disadvantages, however: The actual state of safety in a specific case is not explicitly and quantitatively expressed, and it is not distinguished between the endangered individuals and the whole group. As a result, the effects of the safety measures cannot be measured. This is why uneconomical and in the worst case useless safety precautions cannot be avoided. In addition, waivers are difficult to negotiate, meaningful and sound arguments for pro and con being lacking.

Jan 1, 2007

By Doss Brittain

The term ground breaking is taken to include the process of so loosening the ground as to enable it to be readily loaded into buckets or cars and hoisted from the shaft or drift. In the Joplin district are encountered two varieties of ground, the hard and the soft. Hard ground consists of massively bedded rock requiring heavy blasting to loosen it. Such ground is to be found throughout the district in the same localities as the soft ground but more extensively, even to the exclusion of the appearance of soft ground in the sheet formation in the vicinity of Webb City. The Yellow Dog Mine at Webb City and the Grace mine on the Granby land at Joplin furnish well known examples of hardground mining which has become the most extensive in the district.

Jan 1, 2008

By Krishna Nand

For assessing the safety of structures during underground explosions, ground particle velocity gives the best damage criteria, and 100 mm/see of ground particle velocity has been internationally accepted as the threshold value of safety (no damage). Results of extensive controlled underground explosion experiments conducted by the author to study the effects of ground vibrations on specially prepared concrete blocks, and also on low rise buildings and dams showed that no damage normally occurred when ground particle velocities were less than 100 mm/sec. Analysis of a large number of accelerograms from a dam site in India also indicated that no damage occurred to normal structures when integrated ground particle velocities were less than 100 mm/sec. Major damage in well built structures like a dam was noticed for ground particle velocity as high as about 350 mm/sec. These results are also generally substantiated from damage data obtained for various structures during other earthquakes, including Elcentro (1940), Taft (1952), Parkfield (1965), and San Fernando (1971). These studies, therefore, suggest that the damage criteria during underground explosions and earthquakes are similar; and 100 mm/see of ground particle velocity seems to be the general threshold value of safety (no damage) against ground vibrations.

Jan 1, 1988

By Mo Jadbabaei, Scott Harrison

There is very limited information available regarding the air pressures, flow rate, and velocity profiles in blast hole air drilling applications. Currently, many people are using incompressible flow correlation to calculate the bailing velocity. In this article, air pressure, flow rate, and velocity profiles are calculated using compressible flow theory. The airflow at the bottom of the hole is simulated using the jet flow theory. The concept of choking condition is introduced, and it is concluded that the velocity at the nozzle exit cross section cannot exceed sonic velocity. The minimum pressure required for achieving choked condition at the nozzle cross section is calculated. Choked and overchoked flow conditions at the nozzles are examined, and the maximum achievable cleaning power is correlated to the nozzle size and pressure.

Jan 1, 1999

By Steve Dillingham

The origin of the written blasting log or shot report can likely be traced back to the earliest annals of blasting and record keeping. These records were, for the most part, a way of checking inventory, production progress, or billing, and not necessarily designed with the intention of being used as a legal document in a court of law. As our litigious society has evolved to include far reaching regulatory requirements, however, the blasting log has developed to support and aid in the defense of the common blaster from blasting lawsuits by providing a comprehensive written report of his or her actions.

Jan 1, 2002

Blast vibration analysis under relatively near-field conditions has been carried out in a narrow-vein underground operation. The objective was to characterize the vibration signal (particle acceleration and velocity) from carefully controlled stope blasts. The limitations of such analysis in deriving design guidelines for reducing dilution has been elucidated. It has been shown that identification of each individual hole with specific explosive types can yield explosive-specific predictive equations for particle velocity. This has been coupled with measurement of actual overbreak to arrive at a limiting vibration level to generate a realistic design tool for controlling dilution in narrow-vein mines.

Jan 1, 2003