Search Documents

Increasingly specialized blasting needs require that the explosive energy available in a borehole be reliably known for representative blasting conditions. The underwater test, when properly performed, can yield such information and thus provide a reliable rating of explosives in terms of energy release. This paper reiterates the stringent experimental conditions to be satisfied, and data analysis and interpretation techniques to be followed to achieve this. This is supported by detailed experimental studies involving select parameters in both detonator and booster sensitive explosive compositions. The paper also illustrates the inadvisability of equating blasting performance with the commonly calculated energy values.

Jan 1, 2000

By P D. Katsabanis

Image analysis has been proposed to be an accurate and convenient means of measurement of blast fragmentation. The paper compares the results of image analysis to screening using laboratory scale rock piles. The muckpiles ranged from uniform distribution samples to well graded samples following the Rosin-Rammler distribution.Deviations between screened and imaged distributions were observed in most cases due to the loss of fines. Addition of fines in the system improved the result derived by image analysis considerably. It is suggested that techniques for the prediction of fines be evaluated for modifying the size distributions produced by image analysis.

Jan 1, 1999

By Zhang Qi

For the most part, the flying piece is serious endangerment in the demolition blasting. To prevent the endangerment, a large number of materials are needed as the protection. Therefore, the determination and design way of the flying distance of piece in demolition blasting have been concerned extensively. Previously, the experienced or half experienced formula was adopted to calculate the distance of the flying pieces. The calculating values of the distances of flying pieces are not identical with the practice results. The problems concerning the design way of flying distance of pieces are researched in the paper.

Jan 1, 1994

By David E. Siskind

Increased mineral consumption and environmental concern have caused much interest in potential damage and annoyance from ground vibration and airblast produced by production blasting in surface mines and quarries. Ground vibrations are traditionally blamed for "shaking the house to its foundations," but often the airblast is responsible, particularly when the distances from mine to structure are large. Simultaneous measurements of ground vibrations, structure vibrations, and indoor and outdoor noise from blasting are being used by the Bureau of Mines to determine the relative importance of the ground and airborne blast energy in shaking the structure and making windows, dishes, etc., rattle.

Jan 1, 1977

By Pierre-Alexandre Abeel, Charles Dowding, Justin Lueker

When blasting is eliminated as a cause of cosmetic cracking, often someone will ask, “If blasting didn’t cause the crack, then what did?” This paper describes detection by remotely operated instrumentation of the new cosmetic crack that was climatologically-induced. The measurement was obtained as a part of the development of Autonomous Crack Measurement (ACM) instruments to measure micro-inch response of cracks to both long-term, climatological, and dynamic, blast vibration effects. The crack occurred in the wall of a structure that was monitored for over 29 months and as such represents one of the longest periods of ACM observation.

Jan 1, 2015

By Charles Zdazinsky

Back-break induced from blasting is a concern in open pit metal mining because it compromises the conditions of the pit’s final walls. Final walls that have excessive blast induced damage commonly require extra attention and can often lead to increased cycle times. Most importantly however, the safety conditions of a back-broken region can be significantly compromised and it must be addressed to prevent injury and/or damage to equipment. This occasionally results in the necessity to alter mine plans to prevent an incident from occurring in a back-broken region which can be costly to the mine.

Jan 1, 2014

By Midori Sakamoto, Nobuaki Sakuma, Tsuyoshi Murashita

Recently, tunnel blasting works near the residential area and existing building are increasing and environmental problems caused by vibration have become serious public concern. In order to solve these problems, blasting works have been conducted with segmented blasting and reduce advance per round. However, with these blasting, work efficiency is not obtained, and regrettably the cost and risk of accident tend to increase. We developed a new controlled tunnel blasting technique with electronic delay detonator. Electronic delay detonator can supply extremely large range of delay period which could not be achieved with conventional pyrotechnical delay detonators. We utilized advantages in initiating hole by hole over entire tunnel face at the same round. Much seismic data obtained from tunnel blasting with conventional detonator was statistically analyzed in order to find average duration time of vibration caused by a single hole initiation. Numerical simulation using sample waves from a single hole initiation was carried out in order to find an optimum delay time which can separate vibration in each hole initiation and without decreasing blast performance. Trial blasting was conducted to examine the correctness of optimum delay time obtained from numerical simulation. This blasting technique was applied to an actual tunnel construction. This tunnel is 2 lane automobile tunnel with a total length of 659 meters and internal cross section of 70 square meters. The purpose of the use of blasting technique on occasion, was the protection of fresh water reservoirs directly above the tunnel, and to keep the effect on local private houses to a minimum. The vibration level against this station was limited under 20 mm/see P.V.V. With this blasting, the tunnel construction was completed without exceeding the limited vibration level, with minimum cost and construction time.

Jan 1, 1998

By Fumihiko Sumiya, Yuji Ogata, Masahiro Seto, Yukio Kato, Yuji Wada, Kunihisa Utsuyama, Yoshikazu Hirosaki

It is well known that emulsion explosives can be dead-pressed especially in underground blasting. Voids in emulsion explosives will affect such malfunction of explosives. To clarify the factors that affect the dead-pressing phenomena, the characteristics of the pressure wave propagation in emulsion explosives were investigated. Three types of microballoons .or microbubbles, glass microballoons(GMB), resin microballoons(RMB) and chemical gas bubbles, were used as sensitizers for emulsion explosives. The pressure profiles inside the explosives were measured to determine the effects of the microballoons or microbubbles contained. The underwater explosion test and the large-scale drop hammer test were carried out to load the explosives with a dynamic pressure and a quasi-dynamic pressure respectively. In the underwater explosion test, the pressure profiles in the emulsion explosives were measured by a piezo-electric pressure gauge inserted to the center of the explosive cartridge which had a diameter of 30mm. In the large-scale drop hammer test, the same type of pressure gauge was placed at the bottom of the explosives. From these experiments, the following results were obtained ; A) The pressure profiles in the sample explosives sensitized by RMB or chemical gases were sharp, while in the sample explosives sensitized by GMB the profile was broad. B) The peak pressure levels in the sample explosives sensitized by RMB or chemical gases were twice as high as that in the sample explosives sensitized by GMB in the underwater explosion test. However in the large-scale drop hammer test, the amplification of the peak pressure is low compared with in the underwater explosion test. C) The impulse value was independent of the types of the microballoons or microbubbles in both tests. It was concluded that the type of the microballoons or microbubbles significantly influenced the characteristics of the pressure wave propagation in emulsion explosives.

Jan 1, 2001

By Dave Kay, Young-Suk Song

To meet the needs of South Korea's rapidly expanding economy, a large number of infrastructure projects are under way to improve transportation efficiency within the nation. These projects include high-speed rail links between major population centres and improvements to the road network. Being densely populated and geographically mountainous, infrastructure development in Korea requires a significant amount of tunnelling. Owing to the predominantly hard granitic nature of rock, drill and blast is the preferred method of tunnel advance. The Korean tunneller, however, faces the same pressures as those of his international counterpart in that both cost and production targets need to be achieved while meeting expectations of both community and regulator.

Jan 1, 2005

By ATF Publications

The following is a summary of the changes that were incorporated into the new Federal Explosives Regulations, 27 CFR Part 55, dated 9/2000. However, in light of the recent events of September 2001, additional changes in the Federal Explosives Laws and Regulations may be forthcoming. The nature and extent of any such potential changes are impossible to gauge at this time. However, this synopsis of the changes contained in the September 2000 Orange Book, ATF P 5400.7 was current at the time of this writing. Any questions regarding this paper should be directed to the Public Safety Branch in ATF Headquarters in Washington, D.C.

Jan 1, 2002

By Sang Ho Cho, Masaji Kato, Masaaki Yamamoto, Masaaki Nishi, Katsuhiko Kaneko

This paper presents a numerical simulation method to predict rock fragmentation and to verify a fracture mechanism by bench blasting. The rock fragmentation, which has been used as a means of the index to estimate the effect of bench blasting, affects the expenses for loading, conveyance and crushing of blasting muck piles. The developed numerical simulation method is based on the finite element method and fracture mechanics and includes the re-meshing procedure to express the fracture process of the rock mass. This paper discusses a procedure for a determination of size distributions of the results, which were calculated by numerical simulation, including the tines.

Jan 1, 2002

By V. Wetzig

In the past, various investigations have been carried out at the Hagerbach Experimental Gallery under accurately reproducible conditions, in order to determine the emissions emanating from blasting operations. Comparative investigations proved that the composition of the blast fumes is influenced by the choice of different explosives. It also emerged that the use of emulsion explosives leads to significantly lower concentrations of harmful substances in the blast fumes. Further investigations concerned the residues and reaction products from the explosive process which are left in the debris. Eluate tests on representative samples of debris were used to determine the concentrations of nitrate, nitrite and ammonium in the debris.

Jan 1, 2001

By Guang-Xin Li, Rui-Ping Guo

Based on the analysis of factors affecting the cracking performance of Silently Cracking Agent (SCA), a new SCA structural model is built and a study on the swelling mechanism of SCA and a method to increase swelling thrust by adding the swelling agent are presented. The reason for blow-out and the theory for avoiding blow-out are put forward. The new model improves the SCA theory and provides new method for developing effective SCA. Based on experiments made in laboratory, two types of SCA are developed. A Temperature Control Meter (TCM) has been developed to solve the alltemperature- crack problem after studying the suitable temperature scope of SCA.

Jan 1, 2000

This is the story of a blast - not a large blast by todays standards as it only involved a total of approximately 50 cubic yards of rock. Nor did this blast involve any new or revolutionary blasting technique or require involved analysis or the applications of rock mechanics theories. Instead, it was a blast that involved the tried-and-true principles of good blasting: precise alignment of blastholes; selection of explosives and detonators designed for the conditions encountered; extreme care in loading and hooking up and the use of several ingenious devices and techniques to achieve the proper loading and firing of the blast

Jan 1, 1976

By Dale L. Ramsey

Blasters in the field for years have been faced with the task of plotting blast locations for future reference and calculating scaled distances or seismograph placement from maps,aerial photo's etc.'With the constellation fully operational, GPS provides a satellite signal transmitted to a ground receiver which will display the desired coordinate positioning worldwide, 24 hours a day in any kind of weather conditions. There are a variety of GPS receivers available with varying levels of accuracy. The field trials of a handheld navigational quality instrument for plotting blast and seismograph locations along with other necessary industry related data is the basis of this paper.

Jan 1, 1994

By Lewis L. Oriard

Some two million cubic yards of sandstone and orthoquartzite were blasted and excavated at Upper Stillwater Dam, located high in the Uinta Mountains in northern Utah. The material was processed to produce concrete aggregate for the construction of the largest roller compacted concrete (RCC) dam ever constructed, and one of just a few in existence. The dam cross-section is shown in Figure 1. The aggregate was sound rock produced from required dam foundation excavation and from a quarry located about 1/2 mile from the dam site. Representative compressive strengths of the sandstones and quartzites were in the range of 20,000 to 30,000 psi.

Jan 1, 1993

By Kirk Yeager

During the last several years the FBI has been involved with a detailed study of explosives designed to replicate formulations utilized world-wide by terrorists. In addition, numerous formulations , based on literature and internet sources were examined. During the early stages of this work, a good many of the energetic mixtures studied were based on simple ammonium nitrate fertilizer. While the use of ammonium nitrate in commercial explosives is well studied and documented, the characteristics of the mixtures produced by criminals and terrorists have been less well researched. To aid law-enforcement in understanding the properties of these poorly understood formulations, a “cradle to grave” examination of their characteristics was conducted.

Jan 1, 2001

By Terry Graf, Bill Thompson, John Guenther

SYNCRUDE CANADA LTD.. operates the largest synthetic crude oil production facility in the world. Over 60,000,000 Bank Cubic Metres of oil sand is mined each year from their open pit located in Fort McMurray, Alberta. Despite the extremely cold temperatures encountered during the winter months and the problems associated with frost buildup, SYNCRUDE has continued to operate on a 12 month per year basis. In 1989 SYNCRUDE mine management embarked on a comprehensive Frost Blasting program to improve mine production of their oil sand moving equipment. The following paper will discuss the development of their frost blasting program to its current status.

Jan 1, 1993

By Jaki M. Wilson, Neville T. Moxon

The detonation pressure of ANFO can be significantly reduced by the addition of low density materials such as polystyrene, bagasse, sawdust or perlite. Laboratory and field test results have shown that homogeneous mixtures of these low density explosives can be produced in a bowl truck and loaded into a blasthole without segregation. The detonation pressure of the mixture can be altered to be more compatible with the material in which it is being used by varying the quantity of low density additive incorporated into the mixture. Field results have shown that these low density explosives can lead to significant cost savings without compromising fragmentation or production.

Jan 1, 1989

By R Deshaise, B Mbhanty

The importance of controlling density of commercial explosives, and the various means to achieve it are described. m e field conditions responsible for density changes during blasting and their effect on blast results are examined. Understanding of the behaviour of density control ingredients such as gas bubbles, glass and plastic microballoons under pressure, is considered essential to predicting explosives performance. Both static and dynamic pressure effects have been studied for typical donor-receptor cartridge configurations. The amplitude and temporal characteristics of dynamic pressures inside receptor explosives have been studied by means of the underwater test, and guidelines developed to limit density changes due to external pressures.

Jan 1, 1989