Search Documents

By Philemon Desrochers, Ken Qian Liu

Following the success of the West Ore Zone distress mass blast in 2001 at Brunswick Mine, a similar approach was taken to distress the North Regional Pillar (NRP) which contained over 3 million tonnes of high grade ore. The NRP is located on the 1000 m Level with very poor hanging-wall (H/W) rock mass qualities. After an extensive geotechnical review, the distress slot is located close to the foot-wall (F/W) of the NRP in order to have the competent ore as H/W. The longitudinal area to distress covers 115 m along the strike and 85 m high from 1000 1-sub to 850 Sill. Prior to the final mass blast, 3 voids were created to allow rock swelling: the North void, the South void and the trench just below the mass blast. After over one year of preparation, the mass blast of 202,000 tonnes was successfully initiated on February 7, 2003 with 1561 electronic detonators and 210,000 kg of emulsion explosives. The blast achieved its objective of distressing the NRP as indicated the mine-wide micro-seismic monitoring system. This paper describes different stages of the project from void preparation to the mass blast itself, as well as some detailed aspects such as muck-pile prediction for mucking sequence with the help of DMC_Blast simulation code and electronic detonators.

Jan 1, 2004

By O Omidi

Selection of delay times to optimize fragmentation has been a controversial topic among researchers and blasting practitioners. This paper reviews previous experimental information and presents the results of new tests conducted in small blocks constructed using a commercial grout. The effect of the delay on the average fragment size, coarse fragmentation and uniformity of fragmentation is discussed. Fragmentation was coarser at extremely short or extremely long delays, while a fairly constant average size was obtained at a variety of intermediate delays. Uniformity, defined as the slope of the fragmentation distribution through the average fragment size, was poor at short and very long delays and relatively constant at the intermediate delays. Some tests attempted to minimize the effect of gas penetration by lining the boreholes with copper tubes. When this was the case average fragmentation changed marginally, while uniformity was significantly affected by delay and was typically smaller than in the unlined tests.

Jan 1, 2014

By Ruilin Yang

Kinematic approach of blast modeling refers to using the velocity, strain, or displacement as controlling parameters to model blasting, rather than the stress and the material constitutive relations. The rock stiffness or constitutive relations is very hard or impossible to obtain due to the complexity of the rock mass property.

Feb 1, 2020

By Eric Roller, Elliott Giles

All flyrock incidents have the potential to result in injuries or fatalities that can result in loss of company reputation, license to operate with clients, and bear the exposure to high cost liability. From 2007 to 2009,one NA Quarry and Construction Business experienced a series of flyrock incidents. In the spring of 2009, this business declared that the frequency and severity of Flyrock Incidents had reached an unacceptable level. A Flyrock Elimination Program was launched.

Jan 1, 2012

By Jeffrey W. Lin, Larry B. Weston, Jonathan D. Abbott, Jordan L. Arthur

Hydrocarbon fuel oils are one of the main components of ammonium nitrate-based explosives, including ANFO (Ammonium Nitrate-Fuel Oil) and emulsions. While a wide variety of fuels can, and have, been used in the manufacture of ANFO and emulsion products, No. 2 diesel, particularly dyed, off-road diesel, is widely used due to its ready availability and use in fueling mining equipment. However, a number of alternatives to standard diesel have been introduced over recent years, namely, biofuels, ‘high-performance’ diesels, and renewable diesels. The pressure to adopt these alternative fuels come from a variety of sources, such as initiatives to reduce carbon footprints, increased lifetime of equipment, and cost-advantages from tax credits. While these factors may provide a very real benefit to the mine site, a consideration that is often missed is how the use of these fuels can impact the formulation and characteristics of the ammonium nitrate-based explosives. Herein will be presented a discussion of these alternative fuels from a chemical perspective as well as the results of several studies focused on how the inclusion of various alternative diesels influences the production and performance of ammonium nitrate explosives. ANFO and emulsion were manufactured using representative fuel sources and studying in terms of the manufacturing parameters, shelf-life, interaction with other chemicals using in mining explosives. Detonation data was then collected for these products and compared to the behavior of products made with standard diesel fuels.

Jan 21, 2025

By Phillip R. Mulligan, Catherine Johnson, Edward Kinzel, Cody Lough, Jason Ho

A shaped charge is an explosive device used to focus detonation energy in a desired direction. Shaped charges have numerous applications in several industries such as oil extraction, weaponry and demolition. The focusing of the detonation energy is the result of the Munroe Effect, which greatly increases the penetration properties of the explosive due to a void in the explosive’s volume. The void in the explosive is lined with a metal substrate that becomes a super-heated projectile when the explosive is detonated. Additive Manufacturing (AM) can allow greater design freedom and geometric complexity for the liner portion of the shaped charge. Specifically, hierarchical structuring and functional grading can potentially provide greater velocity, directionality, and efficiency. By utilizing AM, the conventional use of shaped charges can be greatly expanded upon and may open new possibilities. In this work, selective laser melting (SLM) was used to explore different conical shaped charge (CSC) liners made out of stainless steel 304L. A series of liners were tested that had varying densities and were compared to conventional liners. The CSCs were filled with the high explosive Composition C-4 and detonated to evaluate performance. The blast events were recorded using break wire screens to calculate the velocity of the jet through steel target plates over a standoff of 6 times the charge diameter. A high-speed camera recorded the blast event to calculate the velocity of the jet through the air. The depth of penetration into the steel target plates was also used as a measurement of the effectiveness of the CSCs. The aim of this work is to show the potential for advanced shaped charges produced using SLM.

Jan 1, 2019

By Tony Francelj, D. Scott Scovira, Remi Proulx

The Meikle Mine is a high-grade, underground gold mine that utilizes a primary and secondary stoping method with delayed backfill. The newly developed Rodeo Mine will start production using similar mining methods in late 2001. The combined production for the mines will be 4100 stpd of ore in 2002. Dilution of the secondary stopes resulting from blast induced overbreak of the backfill placed in the primary stopes was an issue identified as being a major contributor to the total mining cost at the Meikle Mine. To address the overbreak issue, a low-density, polystyrene enhanced bulk emulsion was developed and introduced to the mine. The density and energy of the emulsion was varied until an optimal level was reached. The use of a low-density bulk emulsion has greatly reduced the overbreak of the primary stope backfill when blasting the secondary stopes. Benefits to the mines include reduced secondary stope dilution, lowered total mining cost, and increased revenues.1

Jan 1, 2002

By Hans-Peter Rossmanith

Fracture mechanics (Atkinson 1987, Broek 1988, Rossmanith 1978-2002, 1983, 1997, Kanninen & Popelar 1985) and wave propagation (Graf 1975, Rinehart 1975) form the main ingredients in the new electronic detonator based blasting technology. The full potential of using short delay initiation timing in bench and underground blasting can only be exploited if the underlying physical processes are properly understood. From a structural geology point of view, in many open pit mine operations, blasting is performed in incompetent and/or loose rock. Under such conditions the stress waves produced by blasting very quickly dissipate in the rock mass and often their energy cannot effectively be put to work. This contribution shows the effect of open and closed joints – and to some degree also faulting – on the blast wave field and shows the influence of structural geology on the blasting result. A simple engineering method which combines wave propagation and impact mechanics is developed in order to assist the non-scientifically trained blaster in understanding blasting in blocky rock formations. Extensive use will be made of the so-called Lagrange diagram which was introduced in detail in the author’s previous lecture at ISEE 2003 (Rossmanith 2003). This presentation can be considered a continuation of the 2003 presentation.

Jan 1, 2004

By W. Sharkey Bowers

This study was undertaken in order to determine a conservative estimate of the attenuation rate of vibrations through the shallow limestone in South Florida due to quarry blasting.

Feb 1, 2020

By Felix Degold, Mark Ganster

Achieving a customer optimized fragmentation by using robust data from new technologies e.g. GPS positions of boreholes, fragmentation analysis to calibrate the geology and fragmentation prediction models. The inclusion of the collected data into the blast’s design makes it possible to accomplish a desired particle size distribution.

Feb 1, 2020

By John Atkinson, Steve Repola

This paper will describe two blasting plans that have been developed for American Aggregates' Marble Cliff Quarry located near Columbus, Ohio. Two different limestone formations are mined on different levels of the quarry. Each formation requires a different blasting plan which address vibration considerations, crusher productivity, drilling and blasting costs and adjacent neighborhood concerns. Controlled blasting is critical to continued mining operations in this Midwest urban setting.

Jan 1, 1993

By K. Taylor

In surface coal mining, the performance of a shovel through blasted muck is one of the key performance indicators of the blast. Historically, performance has been measured qualitatively based on operator feedback or visuals of the muckpile. More complete shovel data, such as loading times and GPS location, is available from most fleet dispatch systems that are already in place at most truck and shovel operations. With some database and analysis skill, the drill and blast team can take advantage of this data to make targeted improvements to drill and blast designs. An area typically known to cause trouble for shovel operators at this operation are blast boundaries. Blast patterns with and without design changes along the boundaries were studied in this case study. The instantaneous loading times for each shovel pass were analyzed for 75 blasts across two subsequent benches with similar firing direction and shovel paths. The benches were split into three categories: Main body of pattern, boundary with design change, and boundary with no design change. The loading times from the main body of the patterns and where the design change was utilized in the boundary had similar prevalence of good loading times. However, boundary areas without the deign change had approximately 2% more prevalence of poor loading times compared to the main boundary of the pattern. Improving the dig rates through the boundaries up to the average loading time would result in approximately 280 hours taken off the total loading time for one bench. By quantifying the shovel’s performance by GPS location, the drill and blast team can decide how much of a design change is needed, can target precisely only the areas that require it and measure the impact of any changes made

Jan 1, 2024

By Paulo Couceiro, Manuel Lopez Cano, Carlos Rodgriguez Calvo

Apart from its difficult execution, underwater blasting is one of the most critical operations of the blasting techniques; mainly because of the ground vibrations - normally associated with low frequencies -, destructive hydraulic shock waves, the difficult coordination, and high costs. To solve these challenges during the underwater blasting on the expansion program for the Panama Canal “Widening and Deepening of the Pacific Entrance and the South approach Channel to the Third set of Locks of the Panama Canal”, a new method to blast using bulk explosive, developed by MAXAM, was used. The project was successfully executed, and more than 800.000m3 were blasted in less than 5 months, jointly with the biggest underwater drilling platform ever build, the Yuan Dong 007, with ten hydraulic drills on board guaranteeing a high production, excellent fragmentation result, total control of the vibration levels, no complain of the neighborhood surrounding the area of the project and simple local logistic due to the classification of the main product used (an oxidizer classified as 5.1). That was finally sensitized down in the hole.

Jan 1, 2011

By Keith Best

It has been said that when a person does something right no one remembers but when they do something wrong no one forgets. This statement, when applied to the explosives industry, has never been truer. Think about it.How many times have you seen a news crew reporting on how well a blaster is doing his/her job? Normally, all you will see is how bad things are going and how much “damage” is being done.

Jan 1, 2008

By Thomas M. Keevin, Gregory L. Hempen

A user-friendly model for environmental effects from underwater explosions is presently available. The model by Munday et al. (1986) is effective for determining fish mortality radii from underwater shooting. The IBLAST program (Coastline Environmental Services 1986) from this model includes estimates for both borehole-loaded explosives for demolition or rock removal purposes and midwater shots. Midwater shots may be used for fish population assessments or some seismic surveys. The program produces approximate mortality distances for planning purposes. IBLAST does have serious shortcomings of which users should be aware.

Jan 1, 1995

By Tom Snyder, John Brulia

Part I is the first of a series of articles by the authors on hazardous materials (HM) transportation safety and compliance for shippers and carriers who offer and transport commercial explosives in commerce on public highways in the U.S.

Jan 1, 2014

By Sedat Esen

"This paper presents a critical review of the fragmentation data obtained from some large open pit copper and gold mines. Database ncludes 35 mines with Uniaxial Compressive Strength values ranging from 19 MPa to 227 MPa (2756 psi to 32923 psi). Variation in the fragmentation data and the causes are discussed in detail. Quality assurance/quality control (QA/QC) in drilling and blasting was shown to have significant impact on fragmentation. In addition, controllable blast design parameters including drill pattern, powder factor, blast timing, stemming length, etc as well as the large blast sizes havesignificant potential to improve fragmentation. Feed size requirements of crushing and grinding circuits were discussed in detail. The paper discusses the effects of different size fractions (top size, 80 %passing size and % passing 10 mm (0.5 in)) on the downstream processes and the role of the fragmentation model in the mine to mill process. Blast domains based on rock strength and structure canbe established by using a fragmentation model which is calibrated using measured fragmentation data. This allows the blast engineer to compensate for changing rock characteristics and stabilize the ROMfragmentation size and result in increased crusher and mill throughput. Two case studies were presented to demonstrate the benefits achieved in downstream processes. Main benefits were reduced downtime at crusher circuits, improved mill throughput as well as reduced total operating cost. A simple relationbetween uniaxial compressive strength and powder factor was proposed using the database for the optimized mines as a guideline to allow site engineers to compare their sites against the other sites."

Jan 1, 2017

By Anderson da Cunha Meireles, Pedro Garcia, Ernst Young, Leandro Coelho, Carlos Eduardo Soares Feliciano, Key Fonseca de Lima

Rock blasting is a crucial technique employed in mining construction and quarrying industries to fragment large rocks into smaller, more manageable pieces. However, it often generates ground vibrations that can pose significant challenges. This study explores the application of Conformal Prediction (CP) in the context of rock blasting to develop predictive models that estimate blasting-induced vibrations and quantify the associated uncertainties. Various machine learning models were integrated within the CP framework using MAPIE and CREPES libraries. The results demonstrated the effectiveness of CP in providing statistically reliable prediction intervals, making it particularly useful for applications where the stakes of underestimating uncertainty can be high.

Jan 21, 2025

By John Wall

The use of electronic detonators in civil tunnelling applications, to reduce vibration is small firings has been successfully utilised for a number of years. As part of the mining industry’s commitment to reducing blast damage during the development cycle in underground mining applications, a series of development blasts using eDevTM electronic detonators in typical mining applications was conducted in North Queensland, Australia.

Jan 1, 2012

By H. Wallin, I. G. Wallace, J. Akhavan, E. Nilsson

Over the past three years the UK together with Sweden, Norway, Finland, Italy have been taking part in a EU funded Leonardo da Vinci programme. More recently EFEE have participated in the project known as the EU15/10/200715/10/2007Excert project which is aimed at addressing the perceived loss of explosives expertise in several EU nations. This could have implications for explosives safety and industrial competitiveness. The paper outlines the work that has so far been done in phase 1 and describes the work planned for the second phase of the project. The paper will describe work in the UK to develop competencies for all explosives workers in both the civil and defence sectors. These competencies in the form of National Occupational Standards have now been approved in the UK and are accompanied by a range of 24 new National Vocational Qualifications launched in May 2006. The paper will show how the standards define knowledge and skills and how these form the basis for vocational qualifications as well as higher education awards and professional qualifications. This UK initiative is now being considered in other EU countries and the project has now been extended to also include Germany, France, Portugal, Czech Republic, Lithuania and Estonia. To support the occupational standards and qualifications work is also being carried out to improve learning provision in the explosives area. In addition to formal educational and conventional training courses a series of workplace learning initiatives are being pursued as well as internet learning packages. Examples of these initiatives will be given.

Jan 1, 2008