Search Documents

By Tyler Ross, John Tatom, Lon Lantis

The Institute of Makers of Explosives (IME) began development of a Quantitative Risk Assessment (QRA) tool, IMESAFR (Institute of Makers of Explosives Safety Analysis for Risk), in 2005 as a technology transfer effort with the United States Department of Defense (US DoD). Version 2.0 of the software has been developed over the last two years and introduces many new features and upgrades. Key upgrades include a new map-based user interface, new debris density hazard models, a metric version, and additional user options referred to as “conservatism switches”.

Jan 1, 2014

By Frank Huber, Ed Fulop, Neil Singh, Ron Elliott, Blair Gohl, Lewis Clarke

This paper covers the successful application of explosive compaction technology for the densification of the foundation soils for the seismic upgrade of the Seymour Falls Dam, Vancouver, BC. The original earthfill embankment constructed during 1958 to 1961 was upgraded in 2004 to 2007 to withstand the effects of a maximum credible earthquake. This paper provides general background information on the theory of the explosive compaction of soils, history of use, geology of the site, project constraints, explosives selection, blast designs, instrumentation used, problems encountered and solutions implemented, and the results achieved.

Jan 1, 2009

By Cathy Aimone-Martin, Kristin Dunlap Kolden

Blasting was conducted for the Army Corps of Engineers (Corps) in the Columbia River near Saint Helens, Oregon during 2009 and 2010 to deepen the navigation channel as a final phase of a dredging project to accommodate larger container ships. The Columbia River Channel Improvement Project (CRCI) required 4 months to blast and dredge 300,000 yd3 (229,366 m3) of basalt from the bottom of the channel to allow Post-Panamax vessels with drafts up to 50 ft (15.2 m) access to the Ports along the River. Explosives charges were limited to 90 lbs (40.8 kg) per delay for the protection of fish and marine life in the area. A fish mortality study and marine mammal monitoring program was also required by the Corps. Underwater overpressure monitoring was required for each blast and peak overpressures measured 10 ft (3.1 m) above the river bottom 140 ft (42.7 m) from the closest blast hole were not to exceed 70 psi (483 kPa) with a cautionary level of 40 psi (276 kPa). Specifications required sampling rates of 500k S/s and PCB Peizotronics tourmaline pressure sensors. The Corps granted permission to co-locate additional ceramic-type sensors at different sampling rates to design redundant monitoring systems 140 and 300 ft (42.7 and 91.4 m) from blasting and develop a site-specific overpressure attenuation model for the project. This paper presents the correlations of overpressure with cube-root scaled distance factors, a comparison of measurements using three different pressure sensor systems, and a discussion of blast design influence on overpressure measurements.

Jan 1, 2014

By Italo Onederra, Miguel Araos

"In order to characterize non-ideal explosives, the explosives industry rely on unconfined velocity ofdetonation tests and where possible underwater pond tests. The information obtained from such tests isquite helpful, however it cannot tell us much about the dynamics of the detonation reaction process. The detonation process has been studied for ideal explosives and the reaction zone length have been measured. However, for non-ideal explosives, that type of information is not available. Therefore, the primary aim of this work was to capture the detonation process of a non-ideal explosive using high speed video camera to determine the zone length."

Jan 1, 2017

By Phil N. Bradbury

"During a routine belt tightening of all cost centers, the management at the Martin County Coal Surface Mines, located in Martin County Kentucky felt that a thorough investigation of the drilling and blasting program could possibly pinpoint areas where the cost could be cut without sacrificing production. Upon close inspection of the drill benches it was noted that the actual layout of burden,spacing and stemming varied a bit from the actual blast design that the management had outlined for the blasters. This paper will outline the method of reducing the drilling and blasting cost at the Martin County Coal Operation."

Jan 1, 1986

By MacDonald B. Johnson, Douglass P. Bacon

With the advance of science, rise of public interest in environmental matters, and continuing erosion of air quality, Federal and state regulators are demanding an increasing complex array of data concerning emissions produced by burning and detonating energetic materials. The U.S. Department of Defense, one of the world's largest consumers of energetic materials, now must characterize combustion products resulting from open burning/open detonation disposal operations. The catch-all phrase "below detection limits" no longer satisfies the regulators who now want testing to delve into the ppt level for volatile organic compounds and ppt level for semivolatile organic compounds.

Jan 1, 1995

By Hubert den Dikken

ache, especially when it comes to forwarding of small quantities. Air transport is limited to 1.4 explosives on cargo aircraft and 1.4S classified explosives on passenger aircraft, so most samples cannot be transported by air. Ocean transport is a possibility, but due to stowage and segregation regulations of the IMDG code, a very expensive one. Road transport is often the only solution, but high explosives require special trucks with licensed drivers. The solution to these logistic problems is solved by creating a 1.4S (Class C) classification for all high explosives, when packed in special containment vessels.

Jan 1, 1995

By Shad M. Sargand, Glenn A. Hazen, A M. M Jayasuriya

Various types of waves originate from a blast source to propagate through rock/soil media away from the blast. Input vibration to a structure depends on the soil-structure interaction which varies with the dynamic properties at the intersection as well as the stress and strain levels developed from the vibration of the structure-ground system. Hence it is important to study such effects on the response of a structure due to blast loads and this knowledge can be used in the design and control of blasts that are carried out close to buildings, highways and other structures.

Jan 1, 1994

By Wang Xuguang, Kang Tingzhang, Zhang Xiaozhi, Wang Guoli, Li Ziqianga

Emulsion powder and granule explosive is produced through airflow fluidization technology by using W/O emulsion. Maintaining the microstructure of W/O emulsion, it has the advantages of both emulsion explosives, such as good water-resistance and detonation properties and powder explosives, such as low cost and east handling. The basic theory of emulsion powder and granular explosive, choices of constituents and formulation, technology for preparation, equipment and relevant parameters, product property as well as technology for safe use have been illustrated in this essay. Based on the above illustration, related factors influencing property and use result have been analyzed.

Jan 1, 2000

By Mark S. Stagg, Rolfe E. Otterness, Stephen A. Rholl

The Bureau of Mines has developed computer software to study the effects of initiator scatter on all aspects of the blasting process. The software is useful because it is difficult to obtain actual initiator data, particularly the standard deviation which is needed to express initiator scatter. The new software is structured to allow blasters to answer the question: how precise must initiators be to insure a successful blast? Successful is defined statistically in terms of a confidence level. The software can be used with any possible design since there are no restrictions due to size or complexity.

Jan 1, 1992

By J R. "Dick" Daniel

In the fall of 1988, The Cannon mine decided to investigate a central blasting system based on conventional electric blasting detonators being used to initiate rounds primed with Nonel detonators. The advantages of this hybrid detonator system were viewed as being safety and cost effectiveness. A study was done reviewing the safety aspects of utilizing a permanent blasting line installed throughout the main haulage drifts to a central blasting station located at the mine portal. The study addressed the following potential safety hazards: radio frequency induced current, stray current from both electrical utilities and transmission lines, galvanic and electrostatic sources of extraneous current.

Jan 1, 1989

By S Lukovic, Vishwa Bhushan, Calvin J. Konya

Effect of each of these variables has been well characterized for ANFO. This paper presents results of underwater energy measurements for one watergel and one emulsion type of slurry explosive which were initiated by 3 types of initiators (one electric and two cords of different strength) in 2 and 3 inch diameter steel pipes. Results of this 2 x 3 x 2 factorial experiment show the effects of detonating cord on energy released by the watergel and the emulsion explosive. Effect of diameter and its interaction with cord strength have also been characterized for the two explosives.

Jan 1, 1986

By Andy Hudson, Stuart Brashear, David Lilly

Because of greatly increased timing accuracy, electronic detonator systems are a well-known and widely accepted major tool to control and reduce ground vibration. At a Southeastern quarry the authors found that the use of electronic detonators improved the reliability of the well known cubed root scaled distance equation for determining air blast. In addition, the authors noticed significant correlations between selected major peak particle velocity frequencies and air blast magnitudes. The major peak particle velocity frequency alone is a close approximation to air blast magnitudes. This relationship is not as significant or not always evident when standard pyrotechnic initiation systems are used.

Jan 1, 2009

By Mike McGill, Stephen Chung, Dale S. Preece

Cast blasting can be designed to utilize explosive energy effectively and economically for coal mining operations to remove overburden material. The more overburden removed by explosives, the less blasted material there is left to be transported with mechanical equipment, such as draglines and trucks. In order to optimize the percentage of rock that is cast, a higher powder factor than normal is required plus an initiation technique designed to produce a much greater degree of horizontal muck movement. This is a significant change from normal blasting practice where fine fragmentation and sufficient muck movement were the prime requirements to permit efficient excavation.

Jan 1, 1994

By Richard J. Mainiero, James Q. Wheeler, Lewis H. Kopera, Yael Miron, Solin S. W Kwak

The research reported here was part of an effort to evaluate the safety of a process to recover TNT from MK-9 depth bombs by the autoclave meltout process. In this process the depth bombs are heated to 121oC so that the TNT will melt and run into a vat. Unfortunately, asphalt lining the inside surface of the bomb also melts and flows out with the TNT. Prior to this study, it was not known what effect the asphalt contamination and the higher than normal process temperatures (121oC) would have on the sensitivity of the TNT.

Jan 1, 1996

By David R. Holberg

In the Kansas City metropolitan area, mineable Bethany Falls Limestone occurs 80 ft below river level under the 700 acre Park College Campus on the north bank of the Missouri River at Parkville. For 20 years prior to this project various firms passed over this opportunity to mine this property for construction aggregate because of uncertain costs, financial risk, and the difficulty of constructing an entry tunnel. This paper describes the drill and blast construction, rock bolting, and shotcrete lining of a 750 ft. long, 15% declining grade, truck tunnel through several Pennsylvanian limestones and shales.

Jan 1, 1997

By S Burchell

During the past few years, high-speed cameras, laser surveying equipment and photogrammetry have become standard tools for recording blast geometry and results. While laser profiling yields accurate 3-D measurements, most cameras capture only two-dimensional images. Attempts to extract 3-D information from photographs have been unsatisfactory. Recent advances in electronic imaging and computer programming have made it possible to develop a 3-D computer based analysis system which can capture and measure 3-D images quickly and accurately. This paper describes the technology to create 3-D images and to analyze blast geometry before, during and after the blast.

Jan 1, 1992

By S C. Brashear, D A. Anderson, A P. Ritter, S R. Winzer, R Broughton

Results of quarry blasts can be quantified to show the effects of controlled variables. Two studies have been carried out: one to document the effect of delay on fragmentation and the other to show the effects of higher relief patterns and more accurate initiators. By using such techniques as highspeed photography and timing studies of mucking and crushing operations, subtle differences in blasting efficiency can be measured and quarry blasting can be optimized. Given the range of available and developing blasting technologies, quarry operators should resort to quantitative analyses of their blasting practices to get maximum productivity.

Jan 1, 1985

By Minoru Kawamora, Koichi Kurokawa, Kenji Hashimoto

We developed concentrated remote control blasting system to blasting simultaneously at a large number of sites in a mine of large scale. This system is consisted of three parts, the first part is a control station with high voltage power source units, the second part is a relay terminal with relaying and branching units, and the third part is a blasting machine with charging and discharging units. The control station is connected with the blasting machine by mean of control bus wire. The blasting machine adopts MBS(electromagnetic induction blasting system) for the reason of safety and good handling.

Jan 1, 1990

By Evan Smart, Andrew Palangio, David Klingspor, Blessing Taiwo

This study presents a DMAIC-based approach to optimize blasting performance and achieve crusher-compatible fragmentation at the Walker-Severn Quarry in Ontario, Canada. By applying the Six Sigma DMAIC (Define, Measure, Analyze, Improve, Control) framework, the study aims to enhance the integration between blasting and primary crushing operations. Several representative blasts will be simulated and evaluated using both aerial and terrestrial image analysis technologies to assess fragmentation characteristics. The investigation was guided by quarry-specific Key Performance Indicators (KPIs), ensuring that blast design modifications were both practical and operationally relevant. Through structured analysis and data-driven refinement of blast parameters, the study reveals how this framework was used to address the quarry production demand for increased crusher throughput, and reduced processing costs. The existing quarry blast design was assessed as a baseline and compared against the crusher's inlet requirements and the acceptable fines level specified by the quarry. This evaluation aimed to identify and implement modifications to enhance blast performance. A drone (UAV) was employed to capture post-blast images and monitor blast pile displacement. These UAV images were used to generate an orthomosaic image, which was analyzed to assess fragmentation. The orthomosaic was overlaid onto a GIS platform using a 10m-by-10m grid to evaluate fragmentation distribution across the bench and identify areas requiring optimization. Additionally, drone imagery was utilized to monitor the impact of each blast on the subsequent blast's free face and to assess energy utilization for optimizing front-row holes to achieve improved fragmentation. The outcomes of this research offer a replicable methodology for continuous improvement in quarry blasting practices, with a focus on producing fragmentation that aligns with primary crusher requirements.

Jan 26, 2026