Search Documents

By William C. Lane

The Pacific Northwest has an abundance of seamy, coarse granite and basalt rock. It is used primarily for road construction. Small quarries are opened nearest the road work to cut the cost of hauling. The crushers are portable. Small diameter holes 2 1/2" to 3 1/2" are placed close together to insure proper fragmentation. It is not unusual to load and shoot 100 to 700 holes 40' deep.

Jan 1, 1986

By Abdel Rahman, M. Khaled, Abo Makarem

There are four large limestone quarries, located nearby Cairo metropolitan. Drilling and blasting operations are used to extract limestone for the cement industries. In these quarries, the blast vibration should be kept below a certain limit. One of these quarries is Tourah Portland Cement Company (TPCC) limestone quarry which, lies near important and historical large caves, within Tourah Mountain. Therefore, control of blast vibration level becomes very critical.

Jan 1, 2007

By John T. Watson, Jim Bailey

Increasing public awareness is probably the single most important challenge faced by any blasting contractor today. This increased awareness usually results in an outcry for tighter regulations and restrictions on those in the blasting industry. Those affected do not often understand the dynamics of blasting and are simply fearful of the unknown. This reaction very often results in more regulations and restrictions which frequently fail to address the real problems.

Jan 1, 1990

By Conny Postupack, Jim Petrunyak, John Hope

The authors discuss the concepts, engineering considerations, and cost relationships involved in the use of drilling and blasting to accomplish backfilling and reclamation with minimum use of mechanical equipment. The four xchods o f reclsnacisn now in use are reviewed, and their advantages and disadvanrages a r e nocea. Guidelines for seleccrng a particular method are offered in terms of applicability under varying geologic, economic, and technological condirions.

Jan 1, 1989

By Jack Eloranta

This paper describes a method of evaluating shot performance through the use of available mine- data. The mine had already been monitoring the following parameters for other purposes: drill penetration rates, shovel loading rates, crusher throughput, crusher power and crusher hangups. By assigning pit coordinates to these factors, maps showing the location of difficult and favorable blasting are as are identified. Products and techniques are compared by the same method.

Jan 1, 1993

By Scott Gustfason, Richard N. Snyder

What is a safe stand-off distance? Recent mishaps using conventional blasting equipment have seen flyrock as distant as 3,750 feet from the blast area, or close to three-quarters of a mile, therefore, whether below ground, under water, in surface quarries or at a structural demolition site, data signals riding a radio wave promise a new horizon for the users of both electric and non electric blasting circuits.

Jan 1, 1987

By Thomas F. Mechtenberg, Michael S. Powell

In the past several years many coal operators and stone producers have reduced drilling and blasting cost by utilizing Bulk Emulsion/ANFO blends. For many operators the cost of equipment to handle blend products has been a major consideration in evaluating overall cost effectiveness of changing from packaged products or bulk ANFO to blends. This is especially true when the project length is short term or is uncertain.

Jan 1, 1990

By Richard Dooley

This paper is one sided because it presents the problem, but not the solution. The problem of blisters (bubbles) and occasional tears in caisson liners occurred when blasting and we have not found a conclusive cause nor a preventive solution. (For back ground information, consult Techniques of Precision Blasting in the Excavation of Drilled Piers, by George Mosteller at the Sixth Conference on Explosives & Blasting Technique in Tampa, Florida 1980).

Jan 1, 1983

Almost one half of Canada's total land surface is underlain by permafrost. This term describes the thermal condition of earth materials when their temperature remains below 0°C continuously for a number of years. The drilling and blasting of frozen materials requires more energy than the blasting of same in its unfrozen state. The cost of comminution could double in permafrost even with adequate organization, drilling equipment and proper explosives.

Jan 1, 1975

By Steve Collinsworth

Sometimes, for those of us in the right place at the right time with the right product, necessity creates opportunity. Such is my case at a West Virginia coal mine where a mine manager was desperately seeking a way to eliminate coal damage on cast shots while maintaining cast percentage without the expensive process of secondary drilling. This paper will focus on how bottom hole air decking is solving the problem.

Jan 1, 2000

By Gordon M. Matheson, David K. Miller

Sinkhole development in karst terrains is a serious problem and risk to facilities built in these areas. The potential for sinkholes are a function of many things including the chemistry of the underlying rock, the location of water conductive fractures and fissures in the rock, the natural fluctuation of the ground water table, vibrations from various sources and surface regrading activities. When sinkhole open near quarry operations the occurrence of these features is occasionally attributed to vibrations from quarry blasting. The purpose of this paper is to review the evidence regarding the development of sinkholes as a result of quarry blasting. In general, it has been found that sinkholes result from collapse or piping of overburden soils into cavities or caverns developed within underlying carbonate rocks that have been in existence for many thousands of years. The overburden soils in karst areas are typically clayey and as a result are not subject to densification or liquefaction as a result of vibrations. The primary cause of an increased rate of sinkhole development can be attributed to changes in the ground water table or local surface water drainage. These changes may be caused by seasonal fluctuations, ground water level lowering in drought periods, dewatering of excavations or quarries, or local changes in surface drainage resulting from grading activities.

Jan 1, 1998

By John Wright

As part of the redevelopment of the Royal Brisbane Hospital complex in Australia, a number of antiquated buildings were to be demolished and replaced by newer, modem facilities. Aside from the decommissioning of the hospital buildings, the project called for the removal of approximateIy 24,000 bank cubic metres (bcm) of varying quality rock material. Given the sensitivity of the project, in particular the close proximity of the required excavation to the existing hospital structures (-3 metres at the closest point), and the requirement that these were to remain lily operational during the construction phase, it was initially proposed to use hydraulic rock hammers as the primary means of excavation. Poor production rates and unexpected dif3icuIt rock conditions led to a revision of the excavation methods and a feasibility study on drill and blast practices was undertaken. Subsequent to an initial series of trial blasts to illustrate that vibration and flyrock could be adequately controlled, drill and blast methods were used in conjunction with mechanical methods of rock breakage. This paper reviews the drU and blast processes and the practices which were necessary to comply with the multiple constraints imposed on the project. The project has highlighted that modified drill and blast practices remain a cost-effective method of excavation, even in sensitive areas which are commonly deemed inappropriate for such methods.

Jan 1, 2000

By P. R. Mohanty, Kaushik Dey

Blast-induced tunnel overbreak prediction in the past has been based on peak particle velocity measured far from the blast site with necessary extrapolation. This has often resulted in suggesting higher damage threshold levels of Acceleration/PPV for overbreak prediction (Bogdanhoff, 1995, Holmberg and Persson, 1997, Murthy and Dey, 2002). These, site-specific far-field blast vibration studies, have also revealed that predicted PPV levels for overbreak could lie in the range of 700-5000 mm/s, an extremely wide range to generalize. Experimental blasts were conducted, in an underground metal mine located in eastern India, with an objective to study the level of acceleration /peak particle velocity generated in tunnel blasting. Accelerometers and tri-axial geophones with measuring ranges upto 500 g, 254 mm/s respectively, were mounted on the tunnel floor close to the blast face, with sensor distances varying from 15.25m to 36.10m. Due to straight faces the measuring distance could not be reduced further anticipating, in particular, cable damage. The equipment used was of M/s Instantel Inc., Canada. The blast pattern used was burn cut with large dia relief holes providing the required free face. The blast hole depth was 1.8m. Tunnel overbreak was measured using a telescopic offset rod fabricated at Indian School of Mines, Dhanbad, India.

Jan 1, 2004

By Frank Hammelmann, Peter Reinders

This paper briefly describes the past history of blast management. A modern blast management suite is then presented which demonstrates the current capability of the functional link between an electronic blasting system and blast design software. Finally, we look at the potential of tomorrow’s fully integrated blast management systems. From the first time blasting was introduced in mining as part of the production process, blasting technology and blast management have been interconnected. Over the past decades we have gained more recent experience with the new electronic blasting systems in mining, quarrying and construction. To start, the primary focus of electronic blasting was to increase timing accuracy. However, since then the technology has gradually developed, broadened and opened up new possibilities, including impressive flexibility in blast design and full in-situ verification of system functionality. To support this capability, modern electronic blasting systems are specifically designed to facilitate full two-way transfer of information between the office-based blast management software and field-hardened equipment. Blast management systems now comprise a suite of expert systems for planning, documentation, analysis, measurement and prediction of blasts. Within this blast management suite, the blast design software allows the transfer of the blast design information from a PC directly to the hardware of the electronic blasting system. The future development of this technology holds huge potential for the blasting industry.

Jan 1, 2004

By John L. Floyd

The use of explosive energy to displace overburden or waste material can provide substantial savings to operations which normally rely on mechanical means for material removal. To optimize the available explosive energy, it is important to quantify the rock's response to the type of explosive and explosive accessories used. During a blast, rock breakage and movement occur so rapidly that the naked eye cannot detect the details of the fragmentation process. A relatively high speed motion picture camera (500 frames per second) can provide the extended time base needed to analyze in detail the site-specific rock response to the explosive detonation. The data of importance to blast casting that can be quantified from these films includes initial face movement, trajectory of rock, and differential face velocities of the material shot. In addition, the ground swell velocities, stemming confinement, and stemming ejection velocity can be determined. The performance of explosive products and delay element accuracy can also be ascertained. The use of high speed motion picture photography and analysis can reduce the number of field trials necessary to maximize explosive performance and increase the benefit provided by blast casting, and in turn, lower production costs. This paper will discuss the methods used for data accumulation and analysis. In addition, three field studies conducted at three separate mining operations will be presented.

Jan 1, 1988

By Robert Jacob Cefalo, Rio Tinto Kennecott

At the end of 2016, the Mine started a new ore phase in the section of the pit located on the East Wall. The East Wall geological structures required controlled blasting for peak particle velocity (PPV) frequency vibrations to protect the wall. Frequency controlled blasting using linear seed wave superposition modeling was required and implemented to reduce the far-field affects to the wall. This paper covers the work done by the drill and blast engineering group, controls used to protect the mine infrastructure, and the continuation of work-to-date of frequency controlled blasting for wall stability. The narrow width of the layback required the combination of hole sizes to blast large diameter production patterns with smaller diameter trim patterns in the same blast. A single blast had to use different burden & spacing and hole diameters and required the use of different timings throughout the pattern. Electronic detonators were required to limit blast vibrations and accommodate the specific timings needed to reduce low frequencies. The geotechnical group with the help of geotechnical radars worked with the drill and blast group on creating a tracking and reporting of blast performance. The radar readings informed the drill and blast engineers of the performance of the blast as it related to the long term performance of the highwall

Jan 1, 2019

By David R. Ziegler

Blasting complaints are as unpredictable as human nature. Being prepared to speak to the complainant, and having a good idea of what you should say, or what NOT to say, may affect the evolution, and eventual resolution of the complaint. The person taking that first phone call will probably not be responsible for resolving the complaint. However, the person in charge should respond to the complainant ASAP, the same day, if possible.

Jan 1, 1998

By J R. Phin

The properties of all available modern blasting initiation techniques are reviewed. Primadets are nonelectric initiators, the nonelectric features of the system eliminates concern of premature initiation from static or stray currents. The loading techniques are simple and a minimum of training is required. There is no limitation in the number of necessary sequences in which the Primadet need be connected for initiation. This flexibility improves vibration control,and often reduces costs due to increased fragmentation.

Jan 1, 1975

By R DeLon Hunsaker

In the past, quarrying and other small operations have not been able to take advantage of the lower cost, convenience and better performance of bulk slurries. However, with the introduction of repumpable emulsion slurries and their ability to be stored in containers as blasting agents, bulk slurries are now available for small operations with small diameter boreholes and are producing excellent results. This same concept is being used successfully in larger underground operations.

Jan 1, 1984

By James L. Wilcox, Douglass P. Bacon

As the U.S. Environmental Protection Agency (USEPA) and state regulators increase the stringency and enforcement of regulations concerning emissions produced by open-air detonation of energetic materials, research must provide the means of obtaining emissions data. The BangBox emissions testing program established the technical foundations for emissions characterization which have been accepted by the USEPA and other regulatory agencies; the technical issues remaining are nettlesome and require new approaches in test procedures.

Jan 1, 1996