Search Documents

By Catherine T. Aimone-Martin, Susan G. Beattie

A series of small scale explosive tests were performed at a perlite mine near Socorro, New Mexico. The tests were designed to investigate the azimuthal or directional relationship between small scale geologic structures such as joints and the propagation of explosively-induced ground motions. Three shots were initiated within a single borehole located at ground zero at depths varying from 83 m (272 ft) to 10 m (32 ft). An array of three component velocity and acceleration transducers were placed in two concentric rings at distances of 20 m (66 ft) and 40 m (131 ft) surrounding the single hole at 7.5° , 15° , and 30° azimuths as measured from ground zero. Data from the transducers were then used to determine the average propagation velocity and waveform characteristics of the blast vibration through the rock mass at the various azimuths. The rock mass was mapped to determine the predominate joint orientations (strike and dip) and the average propagation velocities were correlated with this geologic information. The results showed that there is a correlation between the predominate joint orientation and ground motion amplitudes and velocity. The more predominate geologic structures allow the wave to follow along their strike thereby forming a planar path of least resistance and in turn, allowing higher velocities and amplitudes. Secondary joints or structures may act in concert with more prominent features to form a network of channels or paths along which the wave moves more freely than it may when traveling against the structures. The greatest azimuthal variations in velocity and amplitude was observed for the shallow shot at 10 m (32 ft) depth.

Jan 1, 1996

By Abdulkadir Karadogan, Zikri Keti, Umit Ozer, Mehmet Aksoy, Ulku Kalayci

This paper presents an investigation about how the motions of blast induced vibration waves were affected by the presence of the fault planes. This study was carried out at Espey Open- Pit Boron (Colemanite) Mine in Turkey. Within the scope of the study, ground vibration components were measured for 8 shots using 9 vibration monitors, considering the direction of the fault. Measurement stations were located around the fault line that intersects the open-pit mine in the north-south direction and on different benches along the fault plane. Then, the data of the vibration components obtained from the 77 recorded events were analyzed and the results were presented.

Jan 1, 2012

By Catherine T. Aimone-Martin, Brent Meins

Blast vibration monitoring for buried pipelines is typically conducted at the ground surface with a shallowly buried geophone. In many jurisdictions across the U.S., blast-related vibration limits set for pipelines are dictated by surface measurements and do not consider the significant reduction of PPV amplitudes acting on the pipe at depth. This study involved a vertical array of geophones deployed in drilled holes at two blasting sites of the Loop 202 South Mountain Freeway construction project in Phoenix, Arizona. City of Phoenix pipeline engineers were concerned that blasting would damage an aged 48-inch (122 cm) prestressed concrete cylinder pipe (PCCP) that serviced water for South Phoenix

Jan 1, 2019

By Brent Blanchard

The use of explosives to safely fell structures can be traced back over 300 years. Since then, dozens of chemists, inventors, blasters and demolition experts worldwide have played prominent roles in the evolution of what has become the modern-day explosive demolition industry. In America, one of the earliest applications of explosive demolition occurred in response to the great fires of San Francisco, where homes and businesses were blasted with gunpowder in a desperate attempt to create firewalls. Later in the 19th century, inventions such as nitroglycerine, dynamite and blasting caps made structural blasting a safe, efficient alternative to conventional demolition methods. The 20th century brought the first experiments in shaped charge technology, and this, combined with developments in portable seismology and non-electric delay systems, allowed an ever-expanding variety of structures to be explosively felled by demolition experts throughout the country. The 1950s and .60s brought a new wave of commercial structural-blasting entrepreneurs (several of whom are still active today), and their efforts towards improving adjacent-structure protection and public relations beget the felling of large commercial buildings in dense urban environments. By the late 1980s, publicity-driven motives were gaining greater influence in the decision to .implode. various structures, and the transformation of blasting operations into promotional spectator events played a role in several injuries and fatalities. Since that time, however, a renewed sense of responsibility practiced by most blasting firms and project officials has resulted in the safe, successful completion of hundreds of recent endeavors. In sum, what appears today as an efficient, economical - and visually spectacular - way to demolish structures has its roots in developments of the past several centuries

Jan 1, 2002

By Kamal Wadhwa

Ever since the introduction of Liquid oxygen explosives in India in 1927, these explosives are being extensively used in the various mining industries such as coal, ironore, limestone, bauxite, magnesite etc. The earlier LOX compositions were based on cellulosic material of Weberlox series of French origin. They contained the basic ingredients of saw dust with an admixture of cork dust, some hydrocarbons and some metallic powders. However, there were some inherent defects in the soaking characteristics of these compositions, in as much as, absorption and retention of liquid oxygen in the cartridges were not properly regulated in the fine pores and in the inter-granular spaces inside the ingredients in a uniform manner.

Jan 1, 1989

By G. C. Naveen

Punatsangchu Hydroelectric Project Authority is constructing 1020 MW underground hydroelectric project in Bhutan. The project envisages construction of concrete dam, Desilting Chamber, Head Race Tunnel, Power House Complex and Tail Race Tunnel. Tunneling is one of the major activity in any underground projects as they are driven for multiple activities. By and large the tunnels are a major part of connecting networks from surface to caverns/underground working sites. Many tunnels in hydropower project are part of water conducting systems and one such important tunnel is the Tail Race Tunnel in this project and had to be excavated in thinly foliated rockmass conditions by D&B method. The rockmass is traversed by three to four joint sets and few minor shear seams. Rock Class “Q” values were between III and IV. Tunnel was excavated by full face parallel hole drilling blasting method. The adopted blasting method consisted of drilling 45mm (1.77 inch) diameter holes to a depth of 2m and the drilled holes were charged with 40mm (1.57 inch) diameter cartridge explosives and charges were initiated with half second non electric initiators. The perimeter holes were drilled at closer spacing of 30cm (1 feet) and alternate holes were charged using 32mm (1.23 inch) diameter cartridges explosive. Low dipping foliation joints present in the rockmass tend to slab in crown portion and erratic occurrence of intrusive bodies lead to unpredictable behavior of rock mass posing a major challenge for the safe excavation. Stability was a major issue through controlled blasting under constant supervision too could not limit the overbreak in certain weak rockmass conditions thereby exposing cavities of about 2.5m (8.2 feet). The stabilization of these cavities and handling the overbreak due to rockmass condition was time consuming and warranted additional supports. With systematic measurements and controlled blast designs the Horse Shoe Shaped Tail Race Tunnel of 9.1 m (29.85 feet) diameter and 304m (997.37 feet) length to connect with Downstream Surge Gallery of 314m (1030 feet) length, 18m (59 feet) wide and 58.8m (193 feet) height in thinly foliated and jointed biotite gneiss rockmass was successfully excavated.

By Rob Grant, Manuel Lopez Cano, Mike Briggs, Ken Fletcher

The scorched desert sands and life giving waters of the River Nile in Egypt have been the back drop to awe inspiring engineering feats for over 4,700 years. The latest engineering marvel to grace the land of the Pharaohs is the Mubarak Pumping Station Project at Toshka. This ambitious project aims to open up an area of 607,000 hectares (1.5 million acres) of barren desert to irrigation based farming with the supply of 29 million tonnes (32 million tons) of water per day, drawn from Lake Nasser on the river Nile. It is anticipated that this currently unpopulated area of southern Egypt will soon flourish and become home to several million Egyptians who will conduct their lives around the water supplied by the 230 kilometers (144 miles) of concrete canals. An integral part of the pumping station is the intake canal. The canal was excavated in two sections – the dry excavation, and the wet excavation. The wet excavation comprised of some 5.5 million cubic meters (7.2 million cubic yards) of rock to be drilled, blasted, and excavated, from the surface of the lake. The challenge at hand was how to achieve this safely, quickly, and cost effectively, with water depths of up to 45 meters (148 feet), excavation depths of up to 47 meters (154 feet), blast production rate peaks of up to 30,000 bank cubic meters (39,200 bank cubic yards) per day, blistering summer air temperatures up to 60°C (140°F), and security concerns about the storage of large quantities of explosives in the Middle East region. The solutions to these challenges were engineered by UEE Explosives and centered around the use of a microgel bulk explosive called Rioflex™ and an international team of engineers and operators from three continents. The microgel and accompanying pumping system allowed pumping rates of up to 17,400 kg (38,400 lb) per day, and more importantly, enabled the bulk product to remain as an oxidizing matrix whilst in transport and storage, transforming into an explosive only moments before being pumped into the blastholes. This case study outlines the underwater drill and blast process employed at the Mubarak Pumping Station Project at Toshka, and the novel solutions to the unique challenges encountered.

Jan 1, 2004

By Ed O'Connor, Per-Anders Persson, Manhong Zhou

This chapter deals with the concepts of shock waves and detonation waves together, because a detonation wave is really a shock wave, supported by the explosive reaction that the shock wave ignites and propagates as it travels through the explosive material. In the context of rock blasting, furthermore, there is justification for treating shock waves and detonation waves together, because the mechanical effect of the detonation in an explosive in a drillhole in rock is propagated and its effects are spread throughout the surrounding rock by means of a shock wave. The overall performance of an explosive in rock blasting or any other application is of course dependent on how much thermal energy is released in the chemical reaction that occurs when the material detonates, and on how much useful mechanical work the reaction products can do as they expand. A major portion of this chapter deals with the prediction and measurement of explosive performance, a subject which is now still in a process of rapid development.

Jan 1, 1997

By Tom Treleaven

This guide presents numerous patterns that provide 8 millisecond separations between initiated charges. The guide is tabulated in seven sections to provide quick reference by number of decks or bunch blasting. The pattern is presented in the section where the highest number of decks works. It should be noted that patterns applicable to multiple deck shootings are also applicable for fewer decks.

Jan 1, 1997

By Charles Zdazinsky

Back-break induced from blasting is a concern in open pit metal mining because it compromises the conditions of the pit’s final walls. Final walls that have excessive blast induced damage commonly require extra attention and can often lead to increased cycle times. Most importantly however, the safety conditions of a back-broken region can be significantly compromised and it must be addressed to prevent injury and/or damage to equipment. This occasionally results in the necessity to alter mine plans to prevent an incident from occurring in a back-broken region which can be costly to the mine.

Jan 1, 2014

By David Kosnik

This paper describes the technology and methods deployed in the continuous autonomous remote monitoring of cracks in interior and exterior walls of a residence near a limestone quarry. The objective is to quantitatively compare crack response due to blast-induced ground motion to that induced by diurnal temperature changes, weather fronts, occupant activity, and other phenomena. The remote monitoring and communication technology developed to obtain and disseminate crack response data for this study may provide the means to mitigate the effect of public concerns about potential impacts of ground vibrations inherent in construction and production of raw materials; it is critical to address these concerns because subsequent litigation may result in delays and increased costs.

Jan 1, 2009

By Ian Bell, Shahram Tafazoli, Bahram Sameti, Aylin Azmin, Edmond Chow, Nima Ziraknejad

Image-based rock fragmentation analysis methods have been applied by blast engineers to estimate rock size distribution for over 25 years. These methods utilize a wide range of image segmentation techniques, from manual to fully-automated, to delineate the edges of the rocks in the image. In most commercially available image-based rock fragmentation analysis systems, rock delineation results are converted to physical rock sizes by introducing one or more reference objects (e.g., basketballs or other objects with known geometry) to the scene as size-scaling references.

Jan 1, 2014

By Jon Andrews

Purpose: To show how in managing risk in avalanche control blasting has changed throughout the years, and try to define the term “Acceptable Risk”. History: The history and the way we manage risk in avalanche control blasting to the avalanche control crews and public has change over the years dramatically. From the mid 1800s to about 1920 was the Risk vs. Rewards era, the Industrial Revolution. Now it is a Risk vs. Liability, the age of Liability.

Jan 1, 2009

By Robert Slivinski, Kyle Hobbs, Michael Stern, John Willox, Brad Jewson

Prairie Mines & Royalty Ltd. produces over 12 million tonnes annually of thermal coal for TransAlta’s Sundance and Keephills power stations from the Highvale Mine. This opencast mine is next to a lake and is surrounded by cottages and farms, which means that blast vibrations and air overpressure have to be kept to a minimum.

Jan 1, 2008

By Ronald Ticona, Anaani Huaman, Andrea Lucero

Mine-to-mill optimization begins with a clear understanding and ongoing assessment of blasting, crushing, and grinding operations. Modification of blasting practices to optimize feed size can increase a mine’s throughput. However, this is only an initial step. To optimize the entire process and fully utilize downstream equipment, fragmentation must be measured at critical points along the size reduction circuit

Jan 1, 2019

By Robert J. Nothnagle, Kristen Franz Begor, Rodney W. Sutch

Recovery of contaminated groundwater in a fractured bedrock system presents some unique problems. Typically, the most common problem occurs from the inability to adequately characterize the discrete fractures through which contaminants may be migrating. Without adequate characterization, difficulties arise in properly positioning recovery wells and verifying the performance of the system. To overcome these difficulties at a site in Upstate New York, an innovative approach was developed involving the creation of an artificial fracture zone through controlled blasting to intercept contaminated groundwater flow.

Jan 1, 1988

By Donald Jonson

Stockholm’s Northern Link, currently Europe’s largest urban road tunnel project, will be about 5 km long from west to east. Running through two separate, mostly parallel tunnels, each with 2-4 lanes, the complex will include numerous entries and exits, as well as a major branch to the north. The total length of tunnel will be 11 km, of which 9 km will be in rock. Over million m3 of rock will be blasted. The Northern Link will open to traffic in 2015. After a 10-year stop to deal with environmental questions regarding Ekoparken, Stockholm’s unique “national city park”, the Northern Link project in the Swedish capital was restarted in the autumn of 2006, with the construction of five works-access tunnels.

Jan 1, 2009

By James Ludwiczak

We are coming to an end of an era in Midwest surface coal mining. For many years, large tracts of coal lands were readily available for sale or lease to surface mine operators.

Jan 1, 1980

By G F. Baur

Even though the benefits of an effective, perimeter control program in production and development blasting are evident to most everyone involved in the mining industry, there continuer to be only select properties where such a program is in effect and is producing on-going and measurable results.

Jan 1, 1992

By Pierre De Pasquale, Gilles Jauffret, Ricardo Chavez

"When blasting in quarries or mines, the main source of inconsistent results is directly related to thenon-homogeneous energy distribution through the rock-mass volume. This variation has differentorigins: drilling deviations, geometry differences from one borehole to another (burden, spacing ...),and inherent geological conditions."

Jan 1, 2016