Search Documents

By Tom Burleson

High-speed photography has proven to be an extremely valuable tool for the evaluation of blasting practices in the Warrior Coal Basin. A research project, coordinated by Nelson Brothers Inc. and The University of Alabama's Mineral Engineering Department, has centered on the use of high-speed photography to study and analyze blast performance. A large number of production shots in this region has been filmed and studied. The data obtained from the films have been used to establish graphical relationships between certain blast parameters and overall shot performance. These relationships will be used to develop a computer model that will estimate cast results from a given burden explosive energy combination. This paper describes the methods and procedures used to develop these relationships. The results of the research are discussed along with plans for continuing the research project.

Jan 1, 1988

By Kis M

The purpose of seismic control of blasting is to indicate the vibration magnitude or to eliminate the occurrence of vibration damage caused by blasting. At the Mining Research Institute in Hungary, a new method has been developed to determine the method of delay. Near the blasting site (within 100-200 meters), the peak value of the particle velocity is determined by calculation and also by measurement. In the calculations, the time error of the electric detonators is taken into consideration. During the test program, the results of the experimental blasts and the calculated data have shown good correlation. The method of calculation helps the operator eliminate vibration damage, while the greatest quantity of charge can be detonated.

Jan 1, 1979

By John P. Ashby

Production blasting is a process of destruction of rock masses in order that ore may be extracted. Many open pit operations are faced with the apparently conflicting requirements of providing large quantities of fragmented rock for the processing plant and of minimizing the amount of damage inflicted upon the surrounding pit slopes. A reasonable compromise between these two conflicting demands may often be found by means of simple engineering of production blasts.

Jan 1, 1980

By Alan Minchinton, Ian Kirby, Jim Chan

It has long been known that successful blasting in soft and hard rock can require the use of different explosives. While choosing an explosive of the right energy density is important, the dynamics associated with non-ideal detonation behaviour play an equally major role. Tuning the energy release rate of an explosive to optimise its blast efficiency can be likened to tuning an internal combustion engine to improve its performance.

Jan 1, 2014

By Rodger Andrews

High cost - low productivity mining methods at the Homestake Mine forced the need for a new and safer means of ore extraction. Vertical Crater Retreat (VCR) was introduced in 1978 and accounts for over 50% of the underground mine production today. Many advantages can be attributed to this form of "bulk mining"; including steady production, decreased labor costs, and the ability to mine bulk stopes in the lower portion of the mine. However, safety and high productivity are the two major advantages. This paper will deal specifically with crater blasting and the application of mass blasting techniques in Vertical Crater Retreat slopes.

Jan 1, 1988

By Winfried Rosenstock

Following successful trials at Chuquicamata / Chile from February to May 2000 and from February 2001 onwards at Burton Coal Mine, RAG International/Thiess Pty Ltd., Queensland / Australia a significant advancement in blasting technology was achieved using electronic detonators. The mine now uses electronic intiation for the majority of overburden blasting.

Jan 1, 2002

By A N: Zditovetsky Shishov, M G. Menzhulin

At present in a building industry demand for products from granite, gabbro and other rocks, steady to erosion, natural and chemical weathering, was essentially increased. It has caused the enlargement of exploitation of stone block deposits and necessity of creation of new technologies of hard stone cut.

Jan 1, 1996

By Magnus Gynnemo

The primary purposes of drilling and blasting in hard rocks is to fracture solid rock and prepare it for excavation and subsequent transport to the crushing plant. Using explosives in excavation operations without counting for the geology gives no consideration to the quality of the macadam product or the excess production of waste material (fines).

Jan 1, 1997

By George Pittman, Dan McCutchen

When an explosive manufacturer in the USA wants to put a new explosive formula or detonator design in the toughest proving ground in North American, it is Florida. Florida conditions have baffled many creditable blasting experts. This paper deals with some of the methods used to overcome these problems.

Jan 1, 1995

This paper describes experience in designing and implementing casting blasts over the past fifteen years. Important design parameters such as powder factor, burden and spacing, blast pattern geometry, front row burden and toe distance, pit width versus height, blast length, explosive selection, millisecond delay timing and tie-in types are discussed.

Jan 1, 1995

By Jack C. Leader

The success of a blast using ANFO in wet boreholes is dependent on the quality of the bag the ANFO is packaged in. When a shot fails the dragline may stop and expensive redrilling may be necessary. The total loss to the mining operation can be hundreds-of-thousands-of-dollars.

Jan 1, 1981

By Duan Baofu, Wang Xuguang, Song Jinquan

In this paper, the model of optimizing selection on preparation of Powdery Emulsion Explosives(PEE) is established by the Neural Net Theory(NNT). On the basis of some data in the study of PEE, the training, prediction and optimizing selection of the Neural Net (NN) model are finished by a compiling procedure. The results indicate that the model is helpful to the preparation of PEE and worthy to extend and apply broadly. KTYWORDS Neural Net Powdery Emulsion Explosives Preparation Optimizing Selection

Jan 1, 2003

By Roger Holmberg, William Hustrulid

Swedish cautious blasting techniques were used to excavate a room at the CSM Experimental Mine in Idaho Springs, Colorado,as part of a ONWI/DOE sponsored nuclear waste disposal research program.

Jan 1, 1981

By John A. Huber

At an underground limestone mine in the Central United States; there were plans for the installation of a limestone processing plant. The special design and layout of the plant called for the installation of a tunnel from the underground mine to the surface above. The dimensions of the tunnel would be 10 feet high, 20 feet wide, and would be 500 feet long on a 17 degree incline. The tunnel would be used for the transportation of raw stone to the surface by a conveyor. A second conveyor would transport processed limestone into the mine for storage, that would be loaded out for shipment later.

Jan 1, 1995

By Liu Hui Yang Nianhua Feng Shuyu

The paper analyzed the dynamic stress in the rock around the tunnel and the effect on the stress variation for the different blasting parameters. Also, the paper verified the theoretical results by dynamic photoelastical tests and provided helpful reference for the design of blasting near a tunnel.

Jan 1, 1998

By Barbara A. Sciever, John H. Sr Schue

Riverboat gambling has caused quite a sensation among people since its talk of coming to Illinois. The year 1992 marked the start of an era for people that had a penchant for gambling, it was the year that riverboat gambling was legalized in the State of Illinois.

Jan 1, 1995

By Theodore A. Christensen

Besides the moral responsibility for ensuring worker safety, today's blasting contractor has a major financial incentive for establishing an effective safety program: on-the-job accidents have a direct impact on a very sensitive cost area - Workers Compensation. Within specific parameters, a good safety program can reduce WC costs by lowering the Experience Modification Rate.

Jan 1, 1993

By Carlos Pañura, Michael Geldres, Alejandro Rojas

In this current era of production in large volumes of surface mining, which demands the realization of large-scale blasting, the mining industry must deal with the impact of the vibrations generated by the detonations that are carried out daily in the mines. In this context, the need arises to minimize and control the impact produced by vibrations by determining the interference times of each generated vibration waveform. The vibration waves are produced by the detonation of the explosive charges of each blasthole, analyzing the vibration waves produced by each blasthole, allow us to determine the optimal time between the detonation of each blasthole to reduce the vibrations of the production shot. Once the optimal time is found, it is possible also, to predict the vibration of the production shot (considering times and sequences) using predictive models. The waveform recorded includes information regarding the particle velocity and the dominant frequencies of the vibration. To determine the time between holes, a graph was constructed with the values of the vector Sum VPP (m / s) vs Time between blastholes (s), once the time between blastholes “t” was found, the simulation of the output sequences continued in such a way that, by adding the single waves generated by the blasthole, it gave us a record of vibrations with the lowest level of vibrations.

By Thomas Palangio, Lyall Workman, Jack Eloranta, Tom C. Palangio

The fragmentation distribution of the blasted ore is an important descriptor of blasting results. Traditionally it has been hard to measure quantitatively. Developments in image analysis over several years makes it more feasible to measure fragmentation before crushing on a continuous basis. Post crushing, mill feed distributions can also be measured.

Jan 1, 2007

By Kamal Wadhwa

Liquid oxygen explosives have been used in India for well over 5 decades now. These are being extensively used both for shallow and deep hole blasting in the various opencast mines and quarries for mining of coal, limestone, ironore, bauxite, magnesite etc. IOL Ltd., are the pioneers in the introduction of these explosives in India and are marketing these under the brand name 'LOXITE'.

Jan 1, 1991